Core Products MANHATTAN MN912 Manual

80 min
Height: 560 mm
Width: 1370 mm
Depth: 390 mm
PLEASE RETAIN THIS INSTRUCTION LEAFLET FOR FUTURE REFERENCE.
BATCH NUMBER
Thank you for choosing this furniture.
BEFORE YOU START ASSEMBLY please store the carton for 48 hours or more so the contents can acclimatise.
PLEASE RETAIN ALL PACKING UNTIL YOU HAVE COMPLETED ASSEMBLY.
Information about your furniture.
This furniture range has been carefully crafted from melamine faced manufactured board.
Each piece is manufactured to the highest standards using specialised computer controlled machinery to ensure accuracy.
Caring for your furniture.
Extreme temperature can cause slight movements in the board material so please avoid placing your furniture close to radiators or other direct sources of heat.
Please avoid exposing your furniture to continued bright sunlight as this can affect the colour.
Any fluid spills should be removed as quickly as possible.
Always lift your furniture when moving as dragging may cause damage to your furniture or flooring.
Always use place mats, coasters or tablecloths to help protect against scratches and accidentally dropped items. Always use heat resistant mats when placing hot or
cold items on to surfaces.
Do not sit or stand on your furniture.
After care.
Wipe all surfaces with a dry cloth and the occasional use of a normal household furniture polish on wood surfaces and a household glass cleaner on glass surfaces.
Please do not use detergents or chemicals on your furniture.
After assembly remove all visible component identification stickers, these should remove easily however any remaining adhesive residue can be easily removed with
a label adhesive removal liquid available from most DIY or hardware stores.
MANHATTAN WIDE SCREEN
TV UNIT
REF. MN912
BEFORE YOU START ASSEMBLY
Please check that you have all the correct
parts and fittings as detailed.
In the unlikely event that you require to
order spare parts or fittings please refer to
your delivery note for details of how to order
using our Parts website.
www.coreproducts.co.uk/parts
Customer help line 01738 630555
We recommend that you build your
furniture on top of a soft clean cover to
ensure the unit does not get marked or
damaged during assembly.

Page 2
A
B
C
D
E
F
G
H
I
J
E
G
A - x1
B - x1
C - x1
D - x1
E - x2
F - x1
G - x2
H - x1
I - x1
J - x1
ASSEMBLY PARTS
ASSEMBLY HARDWARE
x4
Steel Leg
Flat Head Screw
(14mm)
x16
End Panel Hinge
(EPH)
(Includes screws)
x4
Cover Caps
x4
Colour 2
x24
Dowel Minifix Bolt
x36
Cover Caps
x32
Colour 1
x36
Minifix Cams
x1
Wall Fixing Kit
(Includes screws)
MAX SUGGESTED LOADS
17,6 lbs.
2 Kg.
20 Kg.
20 Kg.
15 Kg.

Gx2
1
2
3
A
Rotate
A
End Panel Hinge
(EPH)
Page 3
Repeat this in the
following steps.

H
Rotate
H
Page 4
4
5
6
F

C
G
G
H
Rotate to tighten
H
G
G
F
Rotate to tighten
7
8
9
Page 5

Ex2
D
G
G
F
C
D
H
Rotate to tighten
10
11
12
Page 6

B
B
F
AHD
C
E
E
Rotate to tighten
H
A
F
D
C
E
E
Rotate to tighten
13
14
15
Page 7

B
C
D
H
F
A
I
J
Hinge Adjustment
1
Side Adjustment
3
Depht Adjustment
25
Height Adjustmen
4
17
After you finish the
adjustment of the cams,
cover them whit the
cover caps. AAfter you finish
assembling the cabinet,
take off the adhesive
letters.
16
Page 8
-WARNING! TIPPING HAZARD – Unanchored
furniture can tip over
-WARNING: CHECK FOR HIDDEN PIPES AND
CABLES BEFORE DRILLING.
-IMPORTANT: IF YOUR WALLS ARE NOT SOLID
LIKE BRICK OR STONE, YOU WILL REQUIRE
SPECIALIST FITTINGS (NOT SUPPLIED)
-Pre-drill small pilot hole on the back edge of the
furniture top using a 2mm drill bit. Attach the other
end of the fixing strip to the back edge of the
furniture top using the 15mm screw + washer and
securely tighten.
-Place fixing strip against the wall and mark position
for drilling hole.
-Drill hole in your wall to a depth of 30mm using a
6mm drill bit. If the surface of your wall is soft and
crumbly, we would advise you to use a 5mm drill bit
for a tighter fit.
-Insert plug into hole with end flush to the wall
surface.
-Attach fixing strip to the wall using the 25mm
screw + washer and securely tighten.