Core Products DALLAS DL914 Manual

120 min
Height: 1070 mm
Width: 562 mm
Depth: 410 mm
PLEASE RETAIN THIS INSTRUCTION LEAFLET FOR FUTURE REFERENCE.
BATCH NUMBER
Thank you for choosing this furniture.
BEFORE YOU START ASSEMBLY please store the carton for 48 hours or more so the contents can acclimatise.
PLEASE RETAIN ALL PACKING UNTIL YOU HAVE COMPLETED ASSEMBLY.
Information about your furniture.
This furniture range has been carefully crafted from melamine faced manufactured board.
Each piece is manufactured to the highest standards using specialised computer controlled machinery to ensure accuracy.
Caring for your furniture.
Extreme temperature can cause slight movements in the board material so please avoid placing your furniture close to radiators or other direct sources of heat.
Please avoid exposing your furniture to continued bright sunlight as this can affect the colour.
Any fluid spills should be removed as quickly as possible.
Always lift your furniture when moving as dragging may cause damage to your furniture or flooring.
Always use place mats, coasters or tablecloths to help protect against scratches and accidentally dropped items. Always use heat resistant mats when placing hot or
cold items on to surfaces.
Do not sit or stand on your furniture.
After care.
Wipe all surfaces with a dry cloth and the occasional use of a normal household furniture polish and a household glass cleaner on glass surfaces.
Please do not use detergents or chemicals on your furniture.
After assembly remove all visible component identification stickers, these should remove easily however any remaining adhesive residue can be easily removed with
a label adhesive removal liquid available from most DIY or hardware stores.
Specialist glass care.
Glass can be marked with continual use by contact with rough surfaced objects or strong coloured fluids. In the unlikely event that the glass is damaged it must be
replaced without delay with toughened glass made to specification BS EN12150. Please consult a specialist glass retailer for this.
DALLAS DRINK BAR
REF. DL914
BEFORE YOU START ASSEMBLY
Please check that you have all the correct
parts and fittings as detailed.
In the unlikely event that you require to
order spare parts or fittings please refer to
your delivery note for details of how to order
using our Parts website.
www.coreproducts.co.uk/parts
Customer help line 01738 630555
We recommend that you build your
furniture on top of a soft clean cover to
ensure the unit does not get marked or
damaged during assembly.
02/10/2020

Page 2
ASSEMBLY PARTS
ASSEMBLY HARDWARE
x54
Dowel Minifix Bolt
x28
Cover Caps
x30
x28
Minifix Cams
MAX SUGGESTED LOADS
A - x1
B - x1
C - x1
D - x1
E - x1
F - x1
G - x1
H - x4
I - x2
J - x1
K - x1
L - x1
M - x1
N - x1
(Colour 1)
End panel hinge (EPH)
(Screws included)
x1
Shelf support Wall Fixing Kit
x2
x8 x4
x2
Cover Caps
x2
(Colour 2)
(Screws included)
x1
End Panel Push
(EPPH)
Soft Closing End
Panel Hinge (SCEPH)
(Screws included)
Push to
open system
x1
25,4mm
Leg
x5
Drywall Screw
Hinge
N
B
D
L
A
K
J
O
M
F
I
H
C
E
G
H
H
H
I
O
O - x2
5 Kg.
5 Kg.
2 Kg.
2 Kg.
2 Kg.
2 Kg.
2 Kg.
10 Kg.
(Screws included)

Gently hit to adjust.
Repeat this in the
following steps.
12
1
2
3
Page 3
E
I x 2
E
I
Gently hit
to adjust.
Rotate to tighten

Page 4
4
5
6
F
Turn over
F
E
I
Rotate to tighten
Gently hit
to adjust.
F

7
8
9
Page 5
H x 4
F
I
H
H
H
H
E
Gently hit
to adjust.
C
12 3
Push to open
system

Page 6
10
11
12
C
E
F
H
H
H
H
Gently hit
to adjust.
Rotate to tighten
J
J
I
F
E
C
H H H H
Rotate to tighten
Gently hit
to adjust.
I

End Panel Push
(EPPH)
Hinge
13
14
Page 7
D
!Be careful, make sure each type of hinge is in the right place
End panel
hinge (EPH)
Soft Closing End
Panel Hinge (SCEPH)
D
E
C
I
J
F
H H H H
Rotate to tighten
Gently hit
to adjust.

15
16
Page 8
17
Slide the back panels
inside the cabinet
D
E
HHHH
O
N
O
F
C
B
D
N
E
B
H H H H C
F
Rotate to tighten
Gently hit
to adjust.
O
O
Slide the back panels
inside the cabinet

18
19
Page 9
20
K
A
K
A
Rotate to tighten
Gently hit
to adjust.

21
22
Page 10
23
A
B
D
C
E
F
H
H
H
HO
O
K
N
Gently hit
to adjust.
Rotate to tighten
25,4mm
B
D
E
H
H
H
H
F
A
C
1
2
Insert into
the hole
Slide the shelve
inside the cabinet.
A
D
C
E
B
H
F
G
K
H
HN