coreDAR GLAMOS User manual

Manual
www.coredar.com

In the Box
•GLAMOS 1set
•USB C TYPE Charge Cable
•User's Guide
Tech Specs
•Model name : GLAMOS PRO
•Bluetooth version : 4.2
•Input voltage : 5V 1A
•Battery capacity : 700mah
•Usable time : 2 hours
Design
① ②
③ ④ ⑤
①Staus display LED
②Power LED
③Power Button (ON / OFF)
④Bluetooth Button/ Calibration Button
⑤USB-C TPYE connector

To use
Power ON
•Press the Power Button for 3 seconds.
(When you push the Button, The WHITE LED turn on. And
GLAMOS is working, RGB LED turn on .
•When RGB LED is blinking, Please keep your hans off to the
GLAMOS and wait for 3 seconds, (During calibration, the LEDs
turns on and off as follows)
.
Power OFF
•Press the Power Button for 3 seconds
(Flashes green LED while pressing button)
1m
MAGENTACYAN
YELLOW
BLUEGREEN
REDWHITE
3seconds
GREEN

Status LED Info
RED
GREEN
BLUE
WHITE
•Power On sensor error
•Bluetooth update mode
•Calibration - Bottom Right
•When the power button is pressed to power off
•Calibration Mode on ( GLAMOS in Operation)
•Sleep mode off (Flashing 3 times)
•Calibration –Top Left
•When the power button is pressed to power off (Flashing)
•Calibration - Top Right
RED
•GLAMOS Power in test
•Bluetooth pairing mode
GREEN BLUE
YELLOW
•GLAMOS get ready
CYAN MAGENTA

Function
Bluetooth pairing Mode
•Automatically enters pairing mode on initial operation.
•If the connection is lost, pressing the Bluetooth button for 1 second
will make the RGB LED to flash quickly and enter pairing mode.
android
IOS

Function
Calibration Mode
•Press the Bluetooth button for more than 2 seconds to enter the Calibration
Mode. Touch the 3 corners of the screen you are using to measure the
distance.
* Sequence : Left Top -> Right Top -> Right Bottom
* Keep touching until the calibration is completed
GLAMOS
① ②
③
RED
GREEN
BLUE LED off LED off LED off
①start-> finished ②start -> finished ③start -> finished

Function
GLAMOS Firmware Update Mode
•If GLAMOS is operating, turn off the GLAMOS.
•hold the Bluetooth button while pressing the power button to enter update
mode.
•Hold the power Button.
BLE Firmware Update Mode
•Trun on the GLAMOS
•Press the Bluetooth button, power button at that same time.
Sleep Mode
•It enters sleep mode when there is no touch for 10 minutes.
Wake up Mode
•Cover the GLAMOS, After a while, the blue LED will flash 3 times and
start operation..

Android OS
1. Install "CySmart” application in GooglePlay.
2. Download a Firmware file at Coredar homepage (www.coredar.com)
Ex) GLAMOS_BLE_Firmware_v3.0.cyacd
3. Connect your phone and PC.
This PC\”Your Device Name\Phone\CySmart
Copy the file to folder above
(Filename extension is CYACD)
4. Turn on the GLAMOS and press two button
to enter Bluetooth Update Mode
The Red LED lights up until the update is complete.
* Bluetooth mode is disabled during update execution
Do not turn off the product or press any other buttons during the update.
* If the product does not work due to an update error, press the power
button for 3 seconds to force shutdown.
5. After entering Bluetooth update mode, run the CySmart application on
your phone.
How to Firmware Update (BLE Device)
Power
Button BLE
Button

How to Firmware Update(BLE Device)
6. In the App, select “GLAMOS-OTA-Bootloader”.
7. Select the “Bootloader” icon.
8. Under “Select Upgrade Option”, select “Application Upgrade”.
9. In Select Firmware Upgrade files, select the
GLAMOS_BLE_Firmware_v3.0.cyacd file and press the UPGRADE
button at the bottom.
10. When finished, close the CySmart App.
11. Shut down and restart GLAMOS.

How to Firmware Update(BLE Device)
Select GLAMOS-OTA-Bootloader Select Bootloader Service Select Application Upgrade
Select the file and click UPGRADE UPGRADE proceed

How to Firmware Update(BLE Device)
IOS
1. Install "CySmart” application in Appstore.
2. Download a Firmware file at Coredar homepage (www.coredar.com)
Ex) GLAMOS_BLE_Firmware_v3.0.cyacd
3. Connect your phone and PC.
Run iTunes.
Click iPhone icon( ).
click

How to Firmware Update(BLE Device)
4. Settings → File Sharing → Apps → CySmart
5. Drag and copy the downloaded firmware file into CySmart Documents.
Ex) GLAMOS_BLE_Firmware_v3.0.cyacd
Drag file

How to Firmware Update (BLE Device)
6. Turn on the GLAMOS and press two button
to enter Bluetooth Update Mode
The red LED lights up until the update is complete
* Bluetooth mode is disabled during update execution
Do not turn off the product or press any other buttons
during the update
* If the product does not work due to an update error,
press the power button for 3 seconds to force shutdown.
1. After entering Bluetooth update mode, run the CySmart application on
your phone.
6. In the App, select “GLAMOS-OTA-Bootloader”.
7. Select the “Bootloader” icon.
8. Under “Select Upgrade Option”, select “Application Upgrade”.
9. In Select Firmware Upgrade files, select the
GLAMOS_BLE_Firmware_v3.0.cyacd file and press the UPGRADE
button at the bottom.
10. When finished, close the CySmart App.
11. Shut down and restart GLAMOS.
Power
Button BLE
Button

How to Firmware Update (BLE Device)
Select GLAMOS-OTA-Bootloader Select Pair Select Bootloader Service
Select Application Upgrade Select the file and click UPGRADE UPGRADE proceed

How To Update (GLAMOS Device)
FIRMWARE UPDATE
•You can update the firmware using the DfuSe Demo
program. Without turning on GLAMOS product,
press the Bluetooth button and the power button to
enter GLAMOS firmware mode.
•If it cannot enter, the white light will illuminate.
* After entering DFU Mode, keep the power button
pressed to maintain DFU Mode.(To be updated later)
DFU connection fail DFU connection success
If the DFU connection fails, no information is
displayed. When the DFU connection is successful, the device information appears as shown in the box.
Power
Button BLE
Button

file selection Upgrade Progress
Upload complete
Download the firmware to update from our
homepage.
Choose within the box shown (choose...)Press
the button to select the downloaded file.
File name Ex)
GLAMOS_DFU_Firmware_v3.0.dfu
Upgrade Progress
If you succeed in importing a file, the phrase
"File correctly loaded" appears at the bottom of
the program.
Press the Upgrade button when the phrase is
confirmed.
A warning window may appear as above.
Press the Yes (Y) button to proceed with the update. If the upload is successful, you can verify the
following statement: "Target 00: Upgrade
successful!"

Warning
•High reflectivity mirrors and metal products can malfunction when used as
recognition objects. We recommend using non-metallic objects whenever
possible.
•The battery usage time is 2 hours. Low battery capacity may cause
malfunction or product power loss. It is recommended to charge the USB-C
cable when using it for a long time.

product warranty