Cottonwood StoBed User manual

Live Assembly Assistance 888.608.6086 (Business Days10am-5pm Central Time)
24/7 Email: [e-mail] (reply within one business day)
ASSEMBLY INSTRUCTIONS
StoBed
ASSEMBLY INSTRUCTIONS 1 of 3
PARTS IN BOX:
AHeadboard/ Footboard (2pcs.)
E Center Support Legs (3pcs.)
C Slats
D Center Support Rail (1pc.)
HARDWARE:
UM6 x 40mm Flat Head Bolt (3pcs.)
VFlat Washer (8pcs.)
WM8 x 45mm Flat Head Bolt (8pcs.)
XWood Screw M3.5x30 (45pcs.)
Y4mm Allen Key (1pc.)
Z5mm Allen Key (1pc.)
Phillips head/starhead Screw Driver (not
included)
BSide Rails (2pc.)
DO NOT RETURN PRODUCT TO YOUR RETAILER.
Contact Technical Support
T M8 Lock Washer (8pcs.)
DO NOT RETURN PRODUCT TO YOUR RETAILER.
Contact Technical Support
a) Foot (4 pcs)
b) End Rail (2 pcs)
RWoodScrew M5x40 (4 pcs.)
Full / Twin (14 pcs)
Qeeen/ King(15 pcs)
F SpacerBlock(2pcs.)

ASSEMBLY INSTRUCTIONS
StoBed
ASSEMBLY INSTRUCTIONS 2 of 3
STEP 1:
Attach Foot(a) and End rail(b) to
Side Rails (B) using M8 x 40mm
Flat Head Bolts (W) with flat washer
(V) and lock washer (T) ,and center
with the bigger M5 x 40 screw(R) to
fix ,as shown in Diagram 1.
Total of 3 attachment points in this
step
B
DO NOT RETURN PRODUCT TO YOUR RETAILER.
Contact Technical Support
DO NOT RETURN PRODUCT TO YOUR RETAILER.
Contact Technical Support
Live Assembly Assistance 888.608.6086 (Business Days10am-5pm Central Time)
24/7 Email: [e-mail] (reply within one business day)
DIAGRAM 2:
B
B
A
A
Z
w
T
v
w
T
v
DIAGRAM 1:
Top
Bottom
a
b
b
a
a
a
b
B
B
R
STEP 2:
Repeat step 1 assembling the
other 3 corners. There are a
total of 9 attachment points in
this step (3 per corner). See
diagram 2

ASSEMBLY INSTRUCTIONS
StoBed
ASSEMBLY INSTRUCTIONS 3 of 3
DIAGRAM 6:
B
B
E
E
E
D
U
U
U
STEP 3:
Attach Center Support Legs (E) to Center Support
Rail (D) using M6 x 40mm Flat Head Bolts (U) as
shown in Diagram 3. Total of 3 attachmentpoints in
this step.
STEP 4:
Attach Slat s(C) to Side Rails (B)
1) Attach the first slat flush with one end of the lip of
the side rails (Part B) using WoodScrews (X) with
your phillips head screw driver as shown in Diagram
4, Total of two attachmentpoints in this step.
2) You next attach the center support rail (D) to this
slat at one end of the center support rail, one
attachmentpoint in this step.
3) Then attach another slat flush with the other end
of the lip of the side rails (Part B), just as you did in
above step 4.1. Now secure the center support to
this slat as you did with the slat at the other
end ,Total three attachmentpoints in this step
4) Now using the spacers (F) enclosed, start at one
end of the bed and secure each slat with screws into
both sides of lip of the side rails (Part B) until you
reach the opposite end of the bed. as shown in
Diagram 5
Note :the spacing between the last two slats may or
may not equal the spacing of the other slats. This is
not a problem and will not affectthe strength of the
assembly, Total of 24-26 attachmentpoints,
depending on bed size, in this step.
STEP 5:
Attach Center Support Rail (D) to Slat Subassembly
(C) using WoodScrews (X) with your phillips
head/starhead screw driver as shown in Diagram6.
Full & Twin: 14 attachment points
King & Queen:15 attachment points
C
Y C
DO NOT RETURN PRODUCT TO YOUR RETAILER.
Contact Technical Support
DO NOT RETURN PRODUCT TO YOUR RETAILER.
Contact Technical Support
Live Assembly Assistance 888.608.6086 (Business Days10am-5pm Central Time)
24/7 Email: [e-mail] (reply within one business day)
x
x x
D
x
x
x
x If center support legs
(E) are short to the
floor, this can be
corrected by rotating
the black adjustable
glide on the bottom of
the leg
DIAGRAM 4:
DIAGRAM 3:
F
x
D
DIAGRAM 5:
F
x