Country Manufacturing 300 User manual

ESTATE WAGON
MODEL 300
OWNER MANUAL
Country Manufacturing, Inc.
P.O. Box 104
Fredericktown, OH 43019
PH: 740-694-9926
FAX: [phone]

I. INTRODUCTION
The Model 300 Four Wheeled Wagon (ESTATE VERSATILITY WAGON) i de igned for rugged u e and
ver atility. The ideboard are removable from any ide allowing unloading from any of the four ide . By removing
the four corner take the wagon can be converted into a flatbed.
II. ASSEMBLY INSTRUCTIONS
TOOLS REQUIRED
1/2" wrench
5/8” wrench
Plier
FIG. 1
(2)

CHASSIS ASSEMBLY (Refer t FIG 1)
1. Attach the front and rear upport member to center angle iron cha i a hown in figure 1 u ing four (4)
each 5/16” x 1 1/4" bolt , 5/16” nut , and 5/16” lock wa her . Firmly tighten.
2. Attach tongue to front teering yoke by aligning the hole located on the tongue with the teering yoke
bu ing tube and in erting the 5/8” clevi pin. In tall a 1/8” cotter pin thru the clevi pinhole to ecure in
place.
3. Slide each of the four (4) wheel onto the 3/4" axle tub . In tall 3/4" flat wa her . In ert a 1/8” cotter pin
into each axle tub to ecure the wheel .
4. Grea e each of the four wheel via the grea e fitting located on the in ide of each wheel hub.
BED ASSEMBLY (Refer t FIG 1)
1. While holding bed between upright on the cha i align the pivot hole located at rear on the angle iron
runner on the bottom ide of the bed with the two hole on the upright of the real ale holder. Once aligned,
in ert the 1/2" rod through the axle holder and bed hole allowing the bed to pivot. In tall cotter pin thru hole
in 1/2" rod.
2. In tall the four bed corner bracket by removing the four bolt located at each corner of the bed and
rein erting through the hole of each bracket. Firmly ecure u ing a 5/8” wrench.
3. In tall the eight 1” x 6” wood board by in erting each into the groove at each corner take. In tall the two
middle angle iron take into the pocket located midway on the ide rail while hooking the top over the
ideboard.
MAINTENANCE
1. Unloading can be accompli hed from any ide of the wagon by removing the de ired ideboard.
2. Periodically grea e each of the four wheel via the fitting located in ide the hub.
(3)

EXPLODED VIEW MODEL # 300 SERIES – 4 WHEELED WAGON
(4)

PARTS LIST
MODEL 300 SERIES --- 4–WHEELED WAGON
ITEM NO DESCRIPTION PART NO QTY /
UNIT
1 Front Cha i 3001 1
2 Rear Cha i 3002 1
3 Cha i Connector Frame 3003 1
4 Tongue A embly 3004 1
5 Steering Yoke 3005 1
6 Right Wheel Spindle 3006 1
7 Left Wheel Spindle 3007 1
8 Steering Tie Rod 3008 1
9 Bed Attachment Clevi Pin 3009 1
11 Wheel / Tire A embly (16 x 6.50-8) 3011 4
12 3/4" Flat Wa her 3012 4
14 5/16 x 1 1/4 Grade 5 Bolt 3014 4
15 5/16 Nut/Wa her 3015 4
16 Steering Yoke Clevi Pin 3016 1
17 Tongue Attachment Clevi Pin 3017 1
18 Tie Rod Clevi Pin 3018 3
19 5/16 Bolt, Nut, Wa her A embly 3019 4
22 Grea e Fitting 3022 2
23 1/8” Cotter Pin 3023 13
24 7/16” Corner Stake Bolt, Nut, Wa her 3024 4
25 Bed Frame 3025 1
26 Bed Frame Front Angle 3026 1
27 Right Corner Po t 3027 2
28 Left Corner Po t 3028 2
29 Side Support Stake 3029 2
30 Side Board 3030 4
31 End Board 3031 4
32 Floor Board 3032 7
NOTE: Above part can be obtained at your local dealer or by contacting the manufacturer a follow .
Country Manufacturing, Inc.
P.O. Box 104
Fredericktown, OH 43019
PH: 740-694-9926
FAX: [phone]
(5)

WARRANTY POLICY
Country Manufacturing, Inc., will, at it option, replace or repair, without charge to the original
purcha er any part or part manufactured by it and found upon examination, to be
DEFECTIVE IN MATERIAL AND/OR WORKMANSHIP if received for uch examination
within 90 day from date of original purcha e.
Damage re ulting from accident, abu e or neglect are condition under which warranty
cannot be claimed. Nor will warranty apply to damage re ulting from failure to follow the
Manufacturer’ in truction for operation and maintenance nor from the improper election of
a particular application.
All tran portation charge on, and damage and lo incurred in connection with the
tran portation of, part ubmitted for replacement or repair under thi WARRANTY hall be
borne by the purcha er.
No other warrantie , guarantee , or liabilitie , either implied or expre ed, will be the
re pon ibility of Country Manufacturing, Inc.
(6)