A. Remove wall plate from existing wall switch.
B. Disconnect and remove the toggle switch from wall outlet box.
C. Using the wire connectors provided, make the electrical connections to
the wall control as shown in Figure 4. Wrap each wire connector
separately with electrical tape as an extra safety measure.
D. Carefully push all connected wires back inside wall outlet box.
E. Secure wall control with 2 screws provided. Attach wall plate cover with
the 2 original screws.
page 2
Craftmade Customer Support:
1-800-486-4892
www.craftmade.com
JMLI2202
ASSEMBLY OF WALL CONTROL
(Figure 4)
Fig. 4
CAUTION: The transmitter can be programmed to multiple receivers or fans.
If this is not desired, turn wall switch off to any other programmable receiver
or fan.
A. Remove faceplate from remote to reveal battery compartment and
dimmer switch.
B. Install 12-volt battery (included) IMPORTANT: Wall control will not function
unless battery is installed. NOTE: Battery is NOT rechargeable.
Remove battery with low or no charge and dispose of properly.
C.Restore electrical power, set slider switch on wall control to the ON position.
Within 30 seconds of turning on the wall control, press the “OFF” button,
located on the wall control, for 5 seconds or until light on fan blinks twice.
Test the light and fan functions to confirm the programming (learning process)
is complete.
D. Replace faceplate on wall control. (Fig. 4).
A. If you find that your fan and light kit go on and off without using your
remote control, turn power off and repeat Step D under Automated
Learning Process.
B. To prevent damage to transmitter, remove the battery if not used for long
periods.
C. Operation buttons on the front panel of the transmitter:
HIGH button for fan HIGH speed
MED button for fan MEDIUM speed
LOW button for fan LOW speed
OFF button for fan OFF
L button for light BRIGHTNESS and OFF
The light function is controlled by pressing the L button. Hold button
down to increase or decrease light. Tap button quickly to turn light off or on.
If you press the button in excess of 0.7 seconds it becomes a dimmer.
The light varies cyclically in 0.8 seconds. The light button has auto resume
so the light will stay at the same brightness as the last time it was turned off.
1. Download the Bond Home App, available on the Google Play Store and Apple
App Store, or use the QR code to download the app.
2. Open the Bond application.
3. If you already have a Bond account, simply log in and continue to Step 4. If you
do not have a Bond account, press “Create Account” and enter your name,
email and create a password.
4. Select “+” to add a device.
5. Select “Smart By Bond” (SBB).
6. Select this smart ceiling fan.
7. Once the Bond application connects to the fan, select “CONTINUE” to proceed.
8. Test the fan functions:
- You have the option to disable the light function if your fan does not have a
light.
9. Select “YES, IT WORKS.”
10. Specific information about your fan:
-Select “Location” and choose from one of the predefined entries or add
your own by selecting “OTHER”. When finished, select “Save”.
- Select device name and enter the name for your device. When finished,
select “OK” to save.
PLEASE NOTE: This name will be used for integrations so a simple,
easy-to-remember name is best.
11. Select “Continue”.
12. Select the Wi-Fi network you would like to connect the SBB to.
13. Enter the Wi-Fi password and select “OK”.
14. If there is an issue with the connection or wrong password is entered, you will
receive an error message. Select “OK, I’ve Got It”.
15. Once the connection is made, select “DONE”.
16. If the SBB fan is not displayed in the Bond application, swipe down to refresh.
For assistance at any time during this process, go to the “Help” section of the app:
- Tap on “Settings”
- Tap on “Help Center”
- Choose “Open a Ticket” or “Live Chat”
TROUBLESHOOTING GUIDE
A. Remote and/or wall control fails to operate:
1. Make sure there is power to the receiver.
2. Make sure the receiver is wired correctly.
3. Make sure that the fan is set on the highest speed via pull chain.
4. Make sure the light kit is turned on via pull chain.
5. Make sure the battery/batteries in the remote/wall control is/are
good.
6. The learning process between fan and remote and/or wall control
may not have been successful. Turn power off and repeat step D in
“Automated Learning Process”.
B. Transmitter won't operate at a distance: If transmitter operates fan and
light kit when up close but not at 40 feet away, try placing the black
antenna wire higher and make sure the black antenna wire is visible.
ASSEMBLY OF WALL CONTROL
SMART CEILING FAN WI-FI CONTROL
black (OUT to fan)
green
black
(AC IN from
breaker box)
black
(TO POWER supply)
black
green/
bare
ground
outlet box wall
control
faceplate
12V battery
wall plate
AUTOMATED LEARNING PROCESS
CARE AND OPERATION
