Craftmade Olivier OV70-LED User manual

PRINTED IN CHINA
READ THESE INSTRUCTIONS AND
SAVE THEM FOR FUTURE USE
Installation Guide
For Model:
OV70-LED
net weight of fan: 30.2 lb (13.7 kg)
Olivier
APPROVED FOR USE IN
DAMP LOCATIONS
Table of Contents:
Safety Tips. pg. 1
Unpacking Your Fan. pg. 2
Parts Inventory. pg. 2
Installation Preparation. pg. 3
Hanging Bracket Installation. pg. 3
Fan Assembly. pgs. 4 - 5
Wiring. pgs. 5 - 6
Canopy Assembly. pg. 6
Blade Assembly*. pg. 7
Light Kit Assembly. pgs. 7 - 8
Handheld Remote Control Assembly. pg. 9
Automated Learning Process./
Activating Code. pg. 10
Remote/Wall Control Operation. pg. 11
Testing Your Fan. pg. 11
Troubleshooting. pg. 12
Warranty. pg. 12
Parts Replacement. pg. 12
WARNING:
DC Motor will not
operate until blades
are installed
*sold separately

SAFETY TIPS.
page 1
WARNING: To reduce the risk of electrical shock, turn off the electricity to the fan at the main fuse box or circuit panel before you
begin the fan installation or before servicing the fan or installing accessories.
1. READ ALL INSTRUCTIONS AND SAFETY INFORMATION CAREFULLY BEFORE INSTALLING YOUR FAN AND SAVE
THESE INSTRUCTIONS.
CAUTION: To avoid personal injury, the use of gloves may be necessary while handling fan parts with sharp edges.
2. Make sure all electrical connections comply with Local Codes or Ordinances, the National Electrical Code, and ANSI/NFPA
70-1999. If you are unfamiliar with electrical wiring or if the house/building wires are different colors than those
referred to in the instructions, please use a qualified electrician.
3. Make sure you have a location selected for your fan that allows clear space for the blades to rotate, and at least ten (10)
feet (3.05 meters) of clearance between the floor and the fan blade tips. The fan should be mounted so that the tips of
the blades are at least thirty (30) inches (76 centimeters) from walls or other upright structures.
4. The outlet box and ceiling support joist used must be securely mounted, and capable of supporting at least 35 pounds (16
kilograms). The outlet box must be supported directly by the building structure. Use only CETL (Canada) or ETL (USA)
listed outlet boxes marked "FOR FAN SUPPORT."
WARNING: To reduce the risk of fire, electrical shock, or personal injury, mount to the outlet box marked "Acceptable for Fan
Support of 15.9 kg (35 lb) or less," and use the mounting screws provided with the outlet box. Most outlet boxes commonly
used for the support of lighting fixtures are not acceptable for fan support and may need to be replaced. Consult a qualified
electrician if in doubt.
WARNING: To reduce the risk of fire, electrical shock, or personal injury, wire connectors provided with this fan are designed to
accept only one 12 gauge house wire and two lead wires from the fan. If your house wire is larger than 12 gauge or there is more
than one house wire to connect to the corresponding fan lead wires, consult an electrician for the proper size wire connectors to
use.
5. Electrical diagrams are for reference only.
6. After installation is complete, check that all connections are absolutely secure.
7. After making electrical connections, spliced conductors should be turned upward and pushed carefully up into the outlet
box. The wires should be spread apart with the grounded conductor and the equipment-grounding conductor on
opposite sides of the outlet box.
WARNING: To reduce the risk of fire or electrical shock, do not use this fan with any solid state speed control device or control
fan speed with a full range dimmer switch. [Using a full range dimmer switch to control fan speed will cause a loud humming
noise from fan.]
8. Do not operate the reverse switch until fan has come to a complete stop. [Note: If using remote control with reverse
capability, reverse fan blade direction only when on LOW speed.]
9. Do not insert anything between the fan blades while they are rotating.
WARNING: To reduce the risk of personal injury, do not bend the blade arms during assembly or after installation. Do not insert
objects into the path of the blades.
WARNING: To avoid personal injury or damage to the fan and other items, be cautious when working around or cleaning the
fan.
10. Do not use water or detergents when cleaning the fan or fan blades.A dry dust cloth or lightly dampened cloth will be
suitable for most cleaning.
WARNING: To reduce the risk of personal injury, use only parts provided with this fan. The use of parts OTHER than those
provided with this fan will void the warranty.
WARNING: This fan MUST be installed with the safety cable provided with the fan. Failure to use the safety cable provided may
result in personal injury, damage to the fan or damage to other property.
NOTE:This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules.These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
* Reorient or relocate the receiving antenna.
* Increase the separation between the equipment and receiver.
* Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
* Consult the dealer or an experienced radio/TV technician for help.
NOTE: The important safety precautions and instructions appearing in the manual are not meant to cover all possible conditions
and situations that may occur. It must be understood that common sense and caution are necessary factors in the installation
and operation of this fan.

page 2
1. Unpacking Your Fan.
Carefully open the packaging. Remove items from
Styrofoam inserts. Remove motor housing and place
on carpet or Styrofoam to avoid damage to finish. Do
not discard fan carton or Styrofoam inserts should
this fan need to be returned for repairs.
Check against parts inventory that all parts have
been included.
2. Parts Inventory.
a. canopy. 1 piece
b. hanging bracket. 1 piece
c. 3in. downrod with hanging ball. 1 piece
d. 6in. downrod. 1 piece
e. motor housing. 1 piece
f. light kit fitter. 1 piece
g. glass shade. (pre-attached to light kit fitter).
1 piece
h. glass shade cage. (pre-attached to light kit
fitter).1 piece
i. yoke cover. 1 piece
j. blade arm. 5 pieces
k. rubber washer. (pre-attached to light kit fitter).
1 piece
l. hex nut (pre-attached to light kit fitter). 1 piece
m. finial (pre-attached to light kit fitter).
1 piece
n. blade*. 5 pieces
o. canopy cover (in hardware pack). 1 piece
p. anti-sway adapter (in hardware pack).
1 piece
q. wall control. 2 pieces
r. remote control cover. 1 piece
s. plate. 1 piece
t. faceplate. 3 pieces
u. hardware packs
a
g
hj
o
bc
f
e
p
i
k
l
m
n
IMPORTANT REMINDER: You must
use the parts provided with this fan for
proper installation and safety.
d
u
t
s
q
OFF ON
r
I
II
IV
VI
III
V
*Blade drawings in this manual are representative only.
required bulbs:
3 x 4 watt candelabra base LED bulbs
(included)

page 3
3. Installation Preparation.
ON
OFF
ON
OFF
4. Hanging Bracket Installation.
Turn off circuit breakers to current fixture from breaker
panel and be sure operating light switch is turned to the
OFF position.
WARNING: Failure to disconnect power supply prior to
installation may result in serious injury.
Remove existing fixture.
WARNING: When using an existing outlet box, be sure the
outlet box is securely attached to the building structure and
can support the full weight of the fan. Ensure the outlet box is
clearly marked "Suitable for Fan Support." If not, it must be
replaced with an approved outlet box. Failure to do so can
result in serious injury.
CAUTION: Be sure outlet box is grounded and that a ground
wire (GREEN or bare) is present.
Install hanging bracket to outlet box using original screws,
spring washers and flat washers provided with new or
original outlet box.* Arrange electrical wiring around the
back of the hanging bracket and away from the bracket
opening.
*Note: It is very important that you use the proper hardware
when installing the hanging bracket as this will support the
fan.
downrod
installation flushmount
installation
10 feet
(3.05m) (76cm)
30
inches
12ft. - 20ft.
12ft. - 20ft.
(3.66m - 6.1m)
(3.66m - 6.1m)
blade edge
To prevent personal injury and damage, ensure
that the hanging location allows the blades a
clearance of 10 feet (3.05m) from the floor and
30in. (76cm) from any wall or obstruction.
This fan is suitable for room sizes up to 400
square feet (37.2 square meters).
This fan can be mounted with a downrod on a
regular (no-slope) ceiling only. The hanging
length can be extended by purchasing a longer
downrod (0.5in./1.27cm diameter). Fan cannot
be installed as a flushmount or on a vaulted
ceilling.
Installation requires these tools:
Phillips screwdriver, flathead screwdriver,
adjustable pliers or wrench, stepladder, wire
cutters, and rated electrical tape
hanging bracket
spring washers
outlet box screws
flat washers
CANNOT be
installed on
angled or
vaulted ceilings

page 4
5. Fan Assembly.
NOTE: The important safety precautions and instructions
appearing in the manual are not meant to cover all possible
conditions and situations that may occur. It must be
understood that common sense and caution are necessary
factors in the installation and operation of this fan.
set screw
hanging ball
stop pin
set screw hole
hanging
ball
stop pin
diagram 2
diagram 1
diagram 4
diagram 3
clip
downrod
electrical
wiring
safety
cable
yoke set
screw
and nut
pin
Remove hanging ball from downrod provided by
loosening set screw on hanging ball. Lower hanging
ball and remove stop pin and then slide hanging ball
off of the downrod. [Refer to diagram 1.]
Loosen yoke set screws and nuts at top of motor
housing. Remove pin and clip from motor housing
yoke. [Refer to diagram 2.]
Tip: To prepare for threading electrical wires through
downrod, apply a small piece of electrical tape to the
ends of the electrical wires--this will keep the wires
together when threading them through the
downrod. [Refer to diagram 2.]
Determine the length of downrod you wish to use.
Thread safety cable and electrical wires through
threaded end of downrod and pull extra wire slack
from the upper end of the downrod. [Refer to
diagram 2.]
Thread downrod into the motor housing yoke until
holes for pin and clip in downrod align with holes in
yoke--make sure wires do not get twisted. Re-insert pin
and clip that were previously removed. Tighten yoke
set screws and nuts securely. [Refer to diagram 2.]
Locate anti-sway adapter and canopy cover in
hardware packs. Slide yoke cover, canopy cover,
anti-sway adapter and canopy over downrod. [Refer
to diagram 3.] (Note: Canopy cover must be turned
with shiny side toward the motor housing. Anti-sway
adapter must be turned with flat side toward the
canopy.)
Thread safety cable and wires through hanging ball;
then slide hanging ball over downrod--the top of the
downrod should be noted as having a set screw hole;
use this hole when setting the set screw. Insert stop
pin into top of downrod and raise hanging ball. Be
sure stop pin aligns with slots on the inside of the
hanging ball.Tighten set screw securely. [Refer to
diagram 4.]
WARNING: Failure to tighten set screw completely
could result in the fan becoming loose and possibly
falling.
["Fan Assembly" continued on next page.]
canopy
motor
housing
yoke cover canopy
cover
downrod
anti-sway
adapter

page 5
hanging ball slot
hanging bracket tab
motor housing
safety cable
wood screw
and washer
safety cable loop
wood
ceiling joist
canopy
5. Fan Assembly. (cont.)
6.Wiring.
WARNING:Turn off circuit breakers to current fixture
from breaker panel and be sure switch is turned to the
OFF position.
CAUTION: Be sure outlet box is properly grounded and
that a ground (GREEN or Bare) wire is present.
Make sure all electrical connections comply with Local
Codes or Ordinances and the National Electrical Code.If
you are unfamiliar with electrical wiring or if the
house/building wires are different colors than those
referred to in the instructions,please use a qualified
electrician.
Note: Excess lead wire length from the fan can be cut to
the desired length and then stripped.
When downrod is secured in place on the hanging
bracket, electrical wiring can be
made as follows:
Connect BLACK wire from fan to BLACK wire from
ceiling with wire connector provided.
Connect WHITE wire from fan to WHITE wire from
ceiling with wire connector provided.
Connect all GROUND (GREEN) wires together from fan
to BARE/GREEN wire from ceiling with wire connector
provided.
* Wrap each wire connector separately with electrical
tape as an extra safety measure.
black
black
white
white
black supply wire
ground
(green
or bare)
white supply wire
from ceiling
from fan
ground
(green or bare)
*
[”Wiring” continued on following page]
(wiring for fan)
With the hanging bracket secured to the outlet box and able
to support the fan, you are now ready to hang your fan. Grab
the fan firmly with two hands. Slide downrod through
opening in hanging bracket and let hanging ball rest on the
hanging bracket.Turn the hanging ball slot until it lines up
with the hanging bracket tab.
WARNING: Failure to align slot in hanging ball with tab in
hanging bracket may result in serious injury or death.
Tip: Seek the help of another person to hold the stepladder
in place and to lift the fan up to you once you are set on the
ladder.
Find a secure attachment point (wood ceiling joist highly
recommended) and secure safety cable. It will be necessary
to use a heavy duty wood screw, washer and lock washer
(not supplied) with the safety cable loop. If necessary, adjust
the loop at the end of the safety cable.The loop at the end of
the safety cable should just fit over the threads on the wood
screw. Test safety cable by pulling on loose end with pliers. If
the safety cable slips, the loop must be adjusted tighter. Extra
cable slack can be left in ceiling area.

page 6
Modifications not approved by the party responsible for compliance
could void the user's authority to operate the equipment.
*NOTE:This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules.These limits are designed to provide
reasonable protection against harmful interference in a residential installation.This
equipment generates,uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
* Reorient or relocate the receiving antenna.
* Increase the separation between the equipment and receiver.
* Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
6.Wiring. (cont.)
7. Canopy Assembly.
Locate 2 screws on underside of hanging
bracket.
Lift canopy to hanging bracket. Align holes in
canopy with holes in hanging bracket.While
holding canopy in place, slide anti-sway adapter
up to canopy. Align holes in anti-sway adapter
with holes on underside of canopy and then
re-insert the screws that were previously
removed.Tighten both screws securely.
Slide canopy up to anit-sway adapter, aligning
rounded part of slotted holes in canopy cover
with screw heads in bottom of anti-sway
adapter.Turn canopy cover to the right
(clockwise) until it stops.
canopy
canopy cover
hanging bracket
screw
[PLEASE NOTE: Wall and/or handheld remote
control must be used for fan to operate. If you do
not wish to use the wall control,please proceed to
Section 7 below to continue with fan installation.]
To install wall control, remove existing wall
switch.Wire one of the wall controls with wire
connectors provided as shown in diagram at right.
*Wrap each wire connector separately with
electrical tape as an extra safety measure. Gently
push wires and taped wire connectors into outlet
box.
Install one battery (included) in wall control.
IMPORTANT:Wall control will not function unless
battery is installed.
Since this fan comes with incandescent bulbs, the
dimmer switch (labeled ON and D) has been
pre-set to the "ON" position (ON). If you do not
wish to have dimming capability, please move the
switch to the "OFF" position (D).
Attach wall control to outlet box and secure with
screws from original wall switch. Attach plate
(included) to wall control using 2 screws provided
with the wall control.
(wiring for wall control)
black (OUT to fan)
green
black
(AC IN from
breaker box)
black
(TO POWER supply)
black
green/
green/
bare
bare
ground
ground
green/
bare
ground
outlet box wall
control
12V battery
dimmer
switch
plate
I
I
I
I
V
VI
VI
I
I
I
I
I
V

page 7
8. Blade Assembly.
WARNING: To reduce the risk of serious bodily injury,
DO NOT use power tools to assemble the blades. If
overtightened, blades may crack and break.
Locate 15 blade attachment screws/washers in
hardware pack. Locate 15 blade attachment screws
and washers in hardware packs. Hold blade arm up to
blade and align holes. Insert 3 blade attachment
screws (along with washers) with fingers first and
then tighten screws securely with a Phillips
screwdriver. Repeat for the remaining blades.
Remove blade arm screws/lock washers from
underside of motor. Slide blade arm through one of
the openings on motor housing, aligning holes in
blade arm with holes located on the underside of the
motor housing--refer to drawing at right. Attach blade
arm with blade arm screws/lock washers. Before
securing screws permanently, repeat this procedure
with the remaining blade arms. Securely tighten all
screws.
Note:Tighten blade arm screws twice a year.
blade
blade attachment
screws/washers
blade arm screws/
lock washers
blade arm
opening
Place the light kit fitter on its base to
disassemble it. Remove finial, hex nut and
rubber washer. Carefully lift the glass shade
cage from the light kit fitter base. Now,
carefully remove the glass shade and set in
a safe place for later use.
[”Light Kit Assembly” continued on next
page.]
finial
hex nut
rubber washer
glass
shade
cage
glass
shade
light
kit fitter
9. Light Kit Assembly.
light
kit fitter
base

9. Light Kit Assembly. (cont).
Remove 1 screw from motor plate on
underside of motor housing and partially
loosen the other 2 screws.
Connect WHITE wire from motor housing to
WHITE wire from light kit fitter. Connect BLACK
wire from motor housing to BLACK wire from
light kit fitter. Be sure molex connections snap
together securely.
Align slotted holes in light kit fitter with
loosened screws in motor plate. Twist light kit
fitter to lock. Re-insert screw that was
previously removed and securely tighten all 3
screws with Phillips screwdriver.
Install 3 candelabra base 4 watt LED bulbs
(included).
Important: When replacing bulbs, please allow
glass shade cage, glass shade, light kit fitter and
bulb(s) to cool down before touching them.
Re-attach the glass shade and glass shade cage
to the light kit fitter using the rubber washer,
hex nut and finial that were prevously removed.
Do NOT overtighten finial as glass may crack or
break.
motor
plate
molex
connections
motor plate
screw
light kit
tter
finial
hex nut
rubber washer
glass
shade
cage
glass
shade
light kit
fitter
page 8

page 9
dimmer
switch
wall control
wire
wire
wire
12V battery
10. Handheld Remote Control Assembly.
(top)
(bottom)
remote
control
cover
diagram 1
diagram 2
I
I
I
IV
VI
I
I
I
V
wall
control
remote control
cover, BOTTOM
post
hole
diagram 3
post
hole
remote control
cover, TOP
I
II
IV
VI
III
V
IN ORDER TO USE THE HANDHELD REMOTE
CONTROL, CONTINUE WITH SECTION 10 for remote
control assembly instructions.If you have already
installed the wall control but do not wish to use
the handheld remote control,please proceed to
Section 11.
Gently pull on remote control cover to separate
top and bottom parts. [Refer to diagram 1.]
In order to use wall control as a handheld
remote control, cut each wire on wall control
(that was not previously used)--use wire cutters
to cut off each wire as close to the wall control
as possible. [Refer to diagram 2.]
Install one battery (included) in wall control.
[Refer to diagram 2.]
The dimmer switch (labeled DIM and ON) has
been pre-set to the "ON" position (DIM). If you
do not wish to have dimming capability, please
move the switch to the "OFF" position (ON).
[Refer to diagram 2.]
Align holes in wall control with posts located on
inside of TOP part of remote control cover and
press together firmly. Place wall control into
BOTTOM part of remote control cover, aligning
posts in top of remote control cover with post
holes in the bottom. [Refer to diagram 3.]
(NOTE: Make sure to align narrower ends of
remote control cover before closing.) Squeeze
top and bottom of remote control cover
together until you hear a click at each end,
indicating that the remote control cover has
closed completely.
IMPORTANT: Store the remote control away
from excess heat or humidity.To prevent
damage to remote control, remove the battery if
remote control will not be used for long periods.

page 10
11. Automated Learning Process./Activating Code.
wall control
faceplate
(almond
or white)
I
II
IV
VI
III
V
OFF ON
SET button
faceplate
(black)
handheld
remote control
I
II
IV
VI
III
V
O
FF
O
N
SET button
diagram 1
diagram 2
CAUTION: “DO NOT DISPOSE OF BATTERIES IN FIRE, BATTERIES MAY EXPLODE OR LEAK.” - When
disposing of household alkaline batteries, it is best to check with your local and state recycling or
household hazardous waste coordinators concerning the specifics of the program in your area. You
may also locate a recycling center by calling 1-800-8-BATTERY or 1-877-2-RECYCLE or visit
www.epa.gov/epawaste/index.htm or www.earth911.org for more information.
CAUTION:The wall and/or handheld remote control
can be programmed to multiple receivers or fans.If
this is not desired, turn wall switch off to any other
programmable receiver or fan.
Restore electrical power and then, if using wall
control, set slider switch on wall control to the ON
position.Within 60 seconds of turning on the wall
control, press and hold the fan SET button on the
wall control for 5 seconds or until light blinks
twice.
Turn power off again for at least 5 seconds and
then turn power back on. Within 60 seconds of
restoring the power, press and hold the fan SET
button on the handheld remote control for
5 seconds or until light blinks twice.
Test the light and fan functions to confirm the
learning process is complete--see Section 13 on the
following page.
Select a faceplate (almond or white) and press
firmly onto front of wall control that was previously
installed to the outlet box on the wall. [Refer to
diagram 1.]
Attach black faceplate to front of handheld remote
control; press down firmly. [Refer to diagram 2.]
IMPORTANT: Store the handheld remote control
away from excess heat or humidity.To prevent
damage to handheld remote control, remove the
battery if remote control will not be used for long
periods.

page 11
Fan SPEED control buttons--1: Use to control the ceiling fan speed 1-6
Fan OFF button--2: Use to turn the fan off
REVERSE function button--3: Use to control fan direction
LIGHTING button--4: Use to control down-light and up-light (if applicable)
ON/OFF slider switch--5: [Wall control only] Use to turn wall control ON or OFF
IMPORTANT:
Handheld remote
control and wall
control must be
SYNCHRONIZED with
fan in order to
properly function.
handheld
remote control wall control
I
OFF ON
II
III IV
V
VI
12. Remote/Wall Control Operation.
13.Testing Your Fan.
It is recommended that you test fan before finalizing installation.
Restore power from circuit box and light switch (if applicable). Test wall
control (optional installation) by locating ON/OFF slider switch on wall
control, then set to the ON position. Test light and dimmer function and
then test fan speeds. Next, locate handheld remote control. Test fan
speeds with the different fan speed buttons (I - VI) on handheld
remote control.
Test the light ON/OFF function by pressing the
button; test the dimmer function by pressing the button and
holding it down for 1 second.
If the remote control operates all of the
functions of the fan, battery has been installed correctly. If the wall
and/or remote controls do (does) not operate all of the fan functions,
refer to "Troubleshooting" section to solve any issues before contacting
Customer Service.
Fan must be on LOW before setting the fan in reverse. Use button
to recirculate air depending on the season. A ceiling fan will allow you
to raise your thermostat setting in summer and lower your thermostat
setting in winter without feeling a difference in your comfort.
NOTE: If the wall control/handheld remote control interferes with other
appliances, activate a new code on the wall control/ handheld remote
control by turning the power off first. Go back to the instructions for
the SET button in Section 11 (page 10).
IMPORTANT: Handheld remote control and wall control must be
synchronized with fan in order to properly function.
I
II
IV
VI
III
V
4
1
2
3
I
II
IV
VI
III
V
I
OFF ON
II
III IV
V
VI
IMPORTANT: The Automated Learning Process takes approximately 5 minutes to complete. Please
leave the fan “ON” for the duration of the 5-minute programming and do NOT use the
remote control or turn off the power during this time.
The fan will cycle through ALL SIX (6) speeds in forward and reverse and will then stop
automatically after the learning process is complete.

page 12
Troubleshooting.
Problem: Fan fails to operate.
Solutions:
1. Check power to wall switch/wall control.
2.Verify that wall control (optional use) is wired properly.
3. Check to be sure fan is wired properly.
4. Learning process between fan, handheld remote control and, if
applicable, wall control may not have been successful and code was
not activated.Turn off power and repeat instructions for SET button
in Section 11 (page 10).
5. Check that red light on remote control transmitter turns on when
a button is pressed indicating that the battery is good.
Problem: Light kit not lighting.
Solutions:
1. Check wall switch to fan.
2. Check that bulbs are installed correctly.
3. Check that wires in canopy are wired properly.
4.Verify that molex connections in light kit fitter are connected
properly.
5. Learning process between fan, handheld remote control and, if
applicable, wall control may not have been successful and code was
not activated.Turn off power and repeat instructions for SET button
in Section 11 (page 10).
Problem: Fan operates but light fails.
Solutions:
1. Check that bulbs are installed correctly.
2. Check to be sure wires in canopy are wired properly.
3.Verify that molex connections in light kit fitter are connected
properly.
4. Replace defective bulbs with same type of bulb.
Problem: Fan and light fail to operate with remote control.
Solutions:
1. Check battery power to remote control.
2. Learning process between fan, remote control transmitter and
wall control may not have been successful and code was not
activated.Turn off power and repeat instructions for SET button in
Section 11 (page 10).
3. If using optional wall control, check that battery in wall control is
still good.
Problem: Lighting source (up-light, down-light or both) not
functioning.
Solution:
Wattage Limiting Device has interrupted the flow of electricity to
the light source.Ensure bulbs total no more than 190W in the light
source.
Problem: Fan wobbles.
Solutions:
1. Use the balancing kit provided in one of the hardware packs.
If no blade balancing kit is provided, please call Customer Support,
1-800-486-4892, to request one.
2. Check to be sure set screw(s) on motor housing yoke is (are)
tightened securely.
3. Check to be sure set screw on hanging ball is tightened securely.
Warranty.
WARNING: Failure to disconnect power supply prior to
troubleshooting any wiring issues may result in serious
injury.
JMLI1510
Parts Replacement.
For parts and information, please refer to
"Parts Inventory" on page 2.
Craftmade Customer Support:
1-800-486-4892
www.craftmade.com
CRAFTMADE™ LIFETIME LIMITED WARRANTY:
CRAFTMADE warrants this fan to the original household
purchaser for indoor use under the following provisions:
1-YEAR WARRANTY: CRAFTMADE will replace or repair any
fan which has faulty performance due to a defect in
material or workmanship.Contact Craftmade Customer
Service at 1-800-486-4892 to arrange for return of fan.
Return fan, shipping prepaid, to Craftmade. We will repair
or ship you a replacement fan, and we will pay the return
shipping cost.
5-YEAR WARRANTY: CRAFTMADE will repair or replace, at
no charge to the original purchaser, any fan motor that fails
to operate satisfactorily when failure results from normal
use.
RETURN FAN MOTOR ONLY, shipping prepaid, to Craftmade
Industries.We will repair or ship purchaser a replacement
motor and Craftmade will pay the return shipping cost.
6-YEAR to LIFETIME LIMITED WARRANTY: CRAFTMADE will
repair the fan, at no charge for labor only to the original
purchaser, if the fan motor fails to operate satisfactorily
when failure results from normal use. Parts used in the
repair will be billed to the purchaser at prevailing prices at
time of repair.
The purchaser shall be responsible for all costs incurred
in the removal, reinstallation and shipping of the product
for repairs.
This warranty does not apply when damage from
mechanical, physical, electrical or water abuse results in
causing the malfunction. Deterioration of finishes or other
parts due to time or exposure to salt air is specifically
exempted under this warranty.
Neither Craftmade nor the manufacturer will assume any
liability resulting from improper installation or use of this
product. In no case shall the company be liable for any
consequential damages for breach of this, or any other
warranty expressed or implied whatsoever.This limitation
as to consequential damages shall not apply in states
where prohibited.