manuals.online logo
Brands
  1. Home
  2. •
  3. Brands
  4. •
  5. Craftsman
  6. •
  7. Blower
  8. •
  9. Craftsman 358.794900 User manual

Craftsman 358.794900 User manual

Other Craftsman Blower manuals

Craftsman 138.74899 User manual

Craftsman

Craftsman 138.74899 User manual

Craftsman 358.794200 User manual

Craftsman

Craftsman 358.794200 User manual

Craftsman 358.799400 User manual

Craftsman

Craftsman 358.799400 User manual

Craftsman INCREDI-PULL 316.794010 User manual

Craftsman

Craftsman INCREDI-PULL 316.794010 User manual

Craftsman 138. 99078 User manual

Craftsman

Craftsman 138. 99078 User manual

Craftsman 358.798380 User manual

Craftsman

Craftsman 358.798380 User manual

Craftsman 358.794731 User manual

Craftsman

Craftsman 358.794731 User manual

Craftsman CMCBL700 User manual

Craftsman

Craftsman CMCBL700 User manual

Craftsman 154.58973 User manual

Craftsman

Craftsman 154.58973 User manual

Craftsman 358.797960-22cc User manual

Craftsman

Craftsman 358.797960-22cc User manual

Craftsman 358.794963 User manual

Craftsman

Craftsman 358.794963 User manual

Craftsman CMEBL710 User manual

Craftsman

Craftsman CMEBL710 User manual

Craftsman 315.CR2100 User manual

Craftsman

Craftsman 315.CR2100 User manual

Craftsman CMCBL700 User manual

Craftsman

Craftsman CMCBL700 User manual

Craftsman 358.794770 User manual

Craftsman

Craftsman 358.794770 User manual

Craftsman 358748200 - 7.5 Amp Electric Blower User manual

Craftsman

Craftsman 358748200 - 7.5 Amp Electric Blower User manual

Craftsman 900.74828 User manual

Craftsman

Craftsman 900.74828 User manual

Craftsman 358.798980 User manual

Craftsman

Craftsman 358.798980 User manual

Craftsman 358.794741 User manual

Craftsman

Craftsman 358.794741 User manual

Craftsman 358.794763 User manual

Craftsman

Craftsman 358.794763 User manual

Craftsman INCREDI.PULL 316.794802 User manual

Craftsman

Craftsman INCREDI.PULL 316.794802 User manual

Craftsman 257.796362 User manual

Craftsman

Craftsman 257.796362 User manual

Craftsman 358.797120 User manual

Craftsman

Craftsman 358.797120 User manual

Craftsman 51171 User manual

Craftsman

Craftsman 51171 User manual

Popular Blower manuals by other brands

Lithium Earthwise LB20024 Operator's manual

Lithium Earthwise

Lithium Earthwise LB20024 Operator's manual

EINHELL GE-CL 36 Li E Original operating instructions

EINHELL

EINHELL GE-CL 36 Li E Original operating instructions

EINHELL VENTURRO 18/210 operating instructions

EINHELL

EINHELL VENTURRO 18/210 operating instructions

Troy-Bilt 657 Operator's manual

Troy-Bilt

Troy-Bilt 657 Operator's manual

Weed Eater VS2000BV instruction manual

Weed Eater

Weed Eater VS2000BV instruction manual

KRAUSMANN U37020-00 Operation manual

KRAUSMANN

KRAUSMANN U37020-00 Operation manual

GreenWorks Pro BLB482 Operator's manual

GreenWorks Pro

GreenWorks Pro BLB482 Operator's manual

ARIETE 2768 manual

ARIETE

ARIETE 2768 manual

NuTone 331H user guide

NuTone

NuTone 331H user guide

GÜDE GLB 200 18 Li-Ion Translation of the original instructions

GÜDE

GÜDE GLB 200 18 Li-Ion Translation of the original instructions

I.VA.CO. SC Series Operating and maintenance manual

I.VA.CO.

I.VA.CO. SC Series Operating and maintenance manual

DeWalt DCE100 instruction manual

DeWalt

DeWalt DCE100 instruction manual

Ryobi RY40404VN Operator's manual

Ryobi

Ryobi RY40404VN Operator's manual

Becker SV 7.330 operating instructions

Becker

Becker SV 7.330 operating instructions

Metabo AG 18 Pro instructions

Metabo

Metabo AG 18 Pro instructions

Desa GA3650TB installation instructions

Desa

Desa GA3650TB installation instructions

Hanseatic BVN 2500 operating instructions

Hanseatic

Hanseatic BVN 2500 operating instructions

Echo Power Blower PB-230LN Operator's manual

Echo

Echo Power Blower PB-230LN Operator's manual

manuals.online logo
manuals.online logoBrands
  • About & Mission
  • Contact us
  • Privacy Policy
  • Terms and Conditions

Copyright 2025 Manuals.Online. All Rights Reserved.

Instruction Manual
ICRAFTSMAN°I
25cc/1.5 cu.in. 2-Cycle
185 MPH/385 CFM
GASOLINE POWERED
BLOWER
Model No.
358.794900
• Safety
•Assembly
•Operation
•Maintenance
•Parts List
•Espar_ol
WARNING:
Read and follow all Safety Rules and Operating
Instructions before first use of this product.
For answers to your questions about this product:
Call 7 am-7 pm, Mon.-Sat., or 10 am-7 pm, Sun.
1-800-235-5878 (Hours listed are Central Time)
Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.
530165835-01 1/19/05
Warranty Statement 2 Troubleshooting Table 10
Safety Rules 2 Emissions Statement 11
Assembly 4 Parts List 13
Operation 5 Spanish 15
Maintenance 7 Parts and Ordering Back
Storage 9
FULL ONE YEAR WARRANTY ON CRAFTSMAN® GAS BLOWER
For one (1) year from date of purchase, when this Gas Blower is maintained, lu-
bricated, and tuned up according to the instructions in this manual, Sears will re-
pair, free of charge, any defects in material or workmanship.
This warranty excludes blower tubes, spark plug, and air cleaner, which are ex-
pendable parts and become worn during normal use.
Ifthis blower is used for commercial purposes, this warranty applies for 90 days from
the date of purchase. If this Blower is used for rental purposes, this warranty applies
for 30 days from the date of purchase. This warranty applies only while this product
is in use in the United States.
WARRANTY SERVICE ISAVAILABLE BY RETURNING THE BLOWER TO THE NEAREST
SEARS STORE OR SERVICE CENTER IN THE UNITED STATES.
This warranty gives you specific legal rights, and you may also have other rights
which vary from state to state.
Sears, Roebuck and Co., D/817WA, Hoffman Estates, IL 60179
_WARNING: Failure to follow all
Safety Rules and Precautions can re-
sult in serious injury.
KNOW YOUR UNIT
• Read your instruction manual care-
fully until you completely understand
and can follow all warnings and
safety rules before operating the unit.
• Restrict unit to users who under-
stand and will follow all warnings and
safety rules in this manual.
41_WARNING: Inspect area before
starting unit. Remove all debris and
hard objects such as rocks, glass,
wire, etc. that can ricochet, be thrown,
or otherwise cause injury or damage
during operation.
Use your unit as a blower for:
• Sweeping debris or grass clippings
from driveways, sidewalks, patios, etc.
• Blowing grass clippings, straw, or
leaves into piles, around joints, or be-
tween bricks.
PLAN AHEAD
• Always wear eye protection when op-
erating, servicing, or performing main-
tenance on unit. Wearing eye protec-
tion will help to prevent rocks or debris
from being blown or ricocheting into
eyes and face which can result in
blindness and/or serious injury. Eye
protection should be marked Z87.
• Always wear foot protection. Do not
go barefoot or wear sandals.
• Always wear respirator or face mask
when working with unit in dusty envi-
ronments.
• Secure hair above shoulder length.
Secure or remove jewelry, loose
clothing, or clothing with loosely
hanging straps, ties, tassels, etc.
They can be caught in moving parts.
• Do not operate unit when you are
tired, ill, upset, or if you are under the
influence of alcohol, drugs, or medi-
cation.
• Keep children, bystanders, and ani-
mals away from work area a mini-
mum of 30 feet (10 meters) when
starting or operating unit. Do not
point blower nozzle in the direction of
people or pets.
-2-
HANDLE FUEL WITH CAUTION, IT IS
HIGHLY FLAMMABLE
• Eliminate all sources of sparks or
flame (including smoking, open
flames, or work that can cause
sparks) in the areas where fuel is
mixed, poured, or stored.
• Mix and pour fuel in an outdoor area;
store fuel in a cool, dry, well ventilated
place; use an approved, marked con-
tainer for all fuel purposes.
• Do not smoke while handling fuel or
while operating the unit.
• Make sure the unit is properly as-
sembled and in good operating con-
dition.
• Do not fill fuel tank while engine is
running.
• Avoid spilling fuel or oil. Wipe up fuel
spills before starting engine.
• Move at least 10 feet (3 meters)
away from fuel and fueling site be-
fore starting engine.
• Always store gasoline in a container
approved for flammable liquids.
OPERATE YOUR UNIT SAFELY
_ WARNING: This unit is intended
for blower use only. Do not attempt to
open inlet cover. Opened or damaged
inlet cover can result in serious injury.
Discontinue use of blower immediately
if inlet cover becomes opened or dam-
aged. Take unit to your nearest Sears
Service Center for repair.
• Inspect unit before each use for
worn, loose, missing, or damaged
parts. Do not use until unit is in
proper working order.
• Keep outside surfaces free from oil
and fuel.
• Never start or run engine inside a
closed room, building or other un-
ventilated area. Breathing exhaust
fumes can kill.
• To avoid static electricity shock, do
not wear rubber gloves or any other
insulated gloves while operating unit.
• Do not set unit on any surface except
a clean, hard area while engine is run-
ning. Debris such as gravel, sand,
dust, grass, etc. could be picked up by
the air intake and thrown out through
discharge opening, damaging unit,
property, or causing serious injury to
bystanders or operator.
• Avoid dangerous environments. Do
not use in unventilated areas or
where explosive vapors or carbon
monoxide build up could be present=
• Do not overreach or use from unsta-
ble surfaces such as ladders, trees,
steep slopes, rooftops, etc. Keep firm
footing and balance at all times.
• Never place objects inside the
blower tubes; always direct the blow-
ing debris away from people, ani-
mals, glass, and solid objects such
as trees, automobiles, walls, etc. The
force of air can cause rocks, dirt, or
sticks to be thrown or to ricochet
which can hurt people or animals,
break glass, or cause other damage.
• Never run unit without the proper
equipment attached. When using
your unit as a blower, always install
blower tubes.
• Check air intake opening and blower
tubes frequently, always with engine
stopped and spark plug discon-
nected. Keep vents and discharge
tubes free of debris which can accu-
mulate and restrict proper air flow.
• Never place any object in air intake
opening as this could restrict proper air
flow and cause damage to the unit.
• Never use for spreading chemicals,
fertilizers, or other substances which
may contain toxic materials.
• To avoid spreading fire, do not use
near leaf or brush fires, fireplaces,
barbecue pits, ashtrays, etc.
• Use only for jobs explained in this
manual.
MAINTAIN YOUR UNIT PROPERLY
• Have all maintenance other than the
recommended procedures described
in the instruction manual performed
by a Sears Service Center.
• Disconnect spark plug before per-
forming maintenance except for car-
buretor adjustments.
• Use only recommended Craftsman _:
replacement parts; use of any other
parts may void your warranty and
cause damage to your unit.
• Empty fuel tank before storing the
unit. Use up fuel left in carburetor by
starting engine and letting it run until
it stops.
• Do not use any accessory or attach-
ment other than those recommended
by manufacturer for use with your unit.
• Do not store the unit or fuel in a
closed area where fuel vapors can
reach sparks or an open flame from
hot water heaters, electric motors or
switches, furnaces, etc.
• Store in a dry area out of reach of
children.
-3-
SAFETY NOTICE: Exposure to vibra-
tions through prolonged use of gasoline
powered hand tools could cause blood
vessel or nerve damage in the fingers,
hands, and joints of people prone to cir-
culation disorders or abnormal swelling.
Prolonged use in cold weather has been
linked to blood vessel damage in other-
wise healthy people. If symptoms occur
such as numbness, pain, loss of
strength, change in skin color or texture,
or loss of feeling in the fingers, hands, or
joints, discontinue the use of this tool
and seek medical attention. An
antivibration system does not guarantee
the avoidance of these problems. Users
who operate power tools on a continual
and regular basis must monitor closely
their physical condition and the condition
of this tool.
SPECIAL NOTICE: For users on U.S.
Forest Land and in some states, includ-
ing California (Public Resources Codes
4442 and 4443), Idaho, Maine, Minne-
sota, New Jersey, Oregon, and Wash-
ington: Certain internal combustion en-
gines operated on forest, brush, and/or
grass covered land in the above areas
are required to be equipped with a spark
arresting screen, maintained in effective
working order, or the engine must be
constructed, equipped, and maintained
for the prevention of fire. Check with
your state or local authorities for regula-
tions pertaining to these requirements.
Failure to follow these requirements is a
violation of the law. This unit is not facto-
ry equipped with a spark arresting
screen; however, a spark arresting
screen is available as an optional part. If
a spark arresting screen is required in
your area, contact Sears Service for the
correct kit. The spark arresting screen,
blower tubes, and nozzles must be as-
sembled to unit to be in full compliance
with regulations.
CARTON CONTENTS
Check carton contents against the fol-
lowing list.
Model 358.794900
• Blower
• Blower tube
• 2-Cycle Engine Oil
NOTE: It is normal for the fuel filter to
rattle in the empty fuel tank.
ASSEMBLY
_ WARNING: This unit is intended
for blower use only. Do not attempt to
open inlet cover. Opened or damaged
inlet cover can result in serious injury.
Discontinue use of blower immediately
if inlet cover becomes opened or dam-
aged. Take unit to your nearest Sears
Service Center for repair.
,_ WARNING: If you receive your
unit assembled, repeat all steps to en-
sure your unit is properly assembled
and all fasteners are secure.
BLOWER TUBE ASSEMBLY
1. Align the rib on the blower tube
with the groove in the blower outlet;
slide the tube into place.
NOTE: Knob must be loose enough to
allow blower tube to be inserted in blow-
er outlet. Loosen knob by turning coun-
terclockwise.
.,Y-_ Blower
i'4_/f"_ Outlet Blower
_i_,. _ Tube
"_Y Groove _........................_ Rib
2. Secure the tube by turning the
knob clockwise.
3. To remove the tube, turn the knob
counterclockwise to loosen the
tube; remove the tube.
-4-
KNOW YOUR BLOWER
READ THIS INSTRUCTION MANUAL AND SAFETY RULES BEFORE OPERATING YOUR
UNIT. Compare the illustrations with your unit to familiarize yourself with the location
of the various controls and adjustments. Save this manual for future reference.
Primer Button
Thro
Lever
Spark Plug
THROTTLE LEVER
The THRO]q-LE LEVER is used to select
the desired engine speed and to stop the
engine. Move the throttle lever to the
'{_ position for full speed operation.
Move the throttle lever to the _ posi-
tion for idle speed. To stop the engine,
move the throttle lever to the STOP posi-
tion.
PRIMER BUTTON
The PRIMER BUqq-ONremoves air from
the carburetor and fuel lines and fills
them with fuel. This allows you to start
Choke Lever
Fuel Mix
Fill Cap
! _" Starter
_'_ Rope
Rear
Handle
the engine with fewer pulls on the starter
rope. Activate primer button by pressing
it and allowing it to return to its original
position.
CHOKE LEVER
The CHOKE helps to supply fuel to the
engine to aid in cold starting. Activate
the choke by moving the choke lever to
the FULL CHOKE position. After engine
attempts to start, move the choke lever
to the HALF CHOKE position. Once en-
gine starts, move choke lever to the
RUN position.
OPERATING TIPS
•While blowing debris, hold the unit
with the muffler side facing away
from your body and clothes (see OP-
ERATING POSITION below).
• To reduce the risk of hearing loss
associated with sound level(s), hear-
ing protection is required.
• To reduce the risk of injury associated
with contacting rotating parts, stop the
engine before installing or removing
attachments. Do not operate without
guard(s) in place.
• Operate power equipment only at rea-
sonable hours-not early in the morn-
ing or late at night when people might
be disturbed. Comply with times listed
in local ordinances. Usual recommen-
dations are 9:00 a.m. to 5:00 p.m.,
Monday though Saturday.
• To reduce noise levels, limit the num-
ber of pieces of equipment used at
any one time.
• To reduce noise levels, operate pow-
er blowers at the lowest possible
throttle speed to do the job.
• Use rakes and brooms to loosen
debris before blowing.
• In dusty conditions, slightly dampen
surfaces or use a mister attachment
when water is available.
• Conserve water by using power blow-
ers instead of hoses for many lawn
and garden applications, including
areas such as gutters, screens, patios,
grills, porches, and gardens.
• Watch out for children, pets, open
windows, or freshly washed cars.
Blow debris away safely.
• Use the full blower nozzle extension
so the air stream can work close to
the ground.
• After using blowers and other equip-
ment, CLEAN UP! Dispose of debris
in trash receptacles.
-5-
OPERATING POSITION
Eye
Protection
products in the fuel tank or permanent
damage may occur.
Fuel stabilizer is an acceptable alterna-
tive in minimizing the formation of fuel
gum deposits during storage.
Craftsman brand oil is already blended
with fuel stabilizer. See the STORAGE
section for additional information.
NOTE: Unit must be placed on its side
when adding fuel (see illustration below).
Blower
BEFORE STARTING ENGINE
_,WARNING: Be sure to read the
fuel information in the safety rules
before you begin. Ifyou do not
understand the safety rules, do not
attempt to fuel your unit. Call
1-800-235-5878.
FUELING ENGINE
_WARNING: Remove fuel cap
slowly when refueling.
This engine is certified to operate on un-
leaded gasoline. Before operation, gaso-
line must be mixed with a good quality
synthetic 2-cycle air-cooled engine oil.
We recommend Craftsman brand syn-
thetic oil. Mix gasoline and oil at a ratio
of 40:1. A 40:1 ratio is obtained by mix-
ing 3.2 ounces of oil with 1 gallon of un-
leaded gasoline. Included with this blow-
er is a 3.2 ounce container of oil. Pour
the entire contents of this container into
1 gallon of gasoline to achieve the prop-
er fuel mixture. DO NOT USE automotive
oil or boat oil. These oils will cause en-
gine damage. When mixing fuel, follow
instructions printed on container. Once
oil is added to gasoline, shake container
momentarily to assure that the fuel is
thoroughly mixed. Always read and fol-
low the safety rules relating to fuel be-
fore fueling your unit.
IMPORTANT
Experience indicates that alcohol
blended fuels (called gasohol or using
ethanol or methanol) can attract mois-
ture which leads to separation and
formation of acids during storage. Acidic
gas can damage the fuel system of an
engine while in storage. To avoid engine
problems, empty the fuel system before
storage for 30 days or longer. Drain the
gas tank, start the engine and let it run
until the fuel lines and carburetor are
empty. Use fresh fuel next season. Nev-
er use engine or carburetor cleaner
STOPPING YOUR ENGINE
•To stop the engine, move the throttle
lever to the STOP position.
STARTING THE ENGINE
Ai_ WARNING: You MUST make sure
the tubes are secure before using the
unit.
• Fuel engine. Move at least 10 feet (3
meters) away from the fueling site.
• Hold the unit in the starting position
as shown. Make sure the blower end
is directed away from people, ani-
mals, glass, and solid objects.
POSITION
,A
4_ WARNING: When starting engine,
hold the unit as illustrated. Do not set
unit on any surface except a clean, hard
area when starting engine or while en-
gine is running. Debris such as gravel,
sand, dust, grass, etc. could be picked
up by the air intake and thrown out
through the discharge opening, damag-
ing the unit or property, or causing seri-
ous injury to bystanders or the operator.
-6-
STARTING A COLD ENGINE
1. Move the throttle lever to the '_
position.
2. Move the choke lever to the FULL
CHOKE position.
3. Slowly press the primer button 8
times.
ThrottIe Lever Primer Button
Choke Lever
4. Pull starter handle sharply until the
engine attempts to run, but no
more than 5 pulls (below 30"F, 8
pulls).
NOTE: If the engine attempts to start
before the 5th pull, go to the next step
immediately.
5. Move choke lever to HALF CHOKE.
6. Pull the starter handle sharply until
the engine runs, but no more than
5 pulls (below 80°F, 10 pulls).
7. After a 5 second warm-up, move
the choke lever to the RUN posi-
tion.
8. Allow the unit to run for 80 more
seconds at RUN before moving the
throttle lever to the -a_ position.
If the engine has not started after 5
pulls (at HALF CHOKE), repeat the
STARTING A COLD ENGINE procedure.
If the engine still does not start, pro-
ceed to STARTING A FLOODED ENGINE.
9. To stop the engine, move the
throttle lever to the STOP position.
STARTING A WARM ENGINE
NOTE: If fuel tank is empty, add fuel;
then, follow STARTING A COLD ENGINE
procedure. Do not fill fuel tank while
engine is hot.
1. Move the throttle lever to the
position.
2. Pull the starter handle sharply until
the engine starts, but no more than
5 pulls.
NOTE: If the engine has not started,
pull starter handle sharply for 5 more
pulls. If engine still does not run, it is
probably flooded. Proceed to START-
ING A FLOODED ENGINE.
3. To stop the engine, move the
throttle lever to the STOP position.
STARTING A FLOODED ENGINE
Flooded engines can be started by plac-
ing the choke lever in the RUN position.
Move throttle lever to the fast position
; then, pull rope until engine starts.
After engine starts, move the throttle le-
ver to the slow position ._ to allow en-
gine to idle.
Starting could require pulling the starter
rope many times depending on how
badly the unit is flooded. If the unit still
doesn't start, refer to the
TROUBLESHOOTING TABLE or call
1-800-235-5878.
CUSTOMER RESPONSIBILITIES
WARNING: Disconnect the spark plug before performing maintenance,
service, or adjustments.
CARE & MAINTENANCE TASK
Check for loose fasteners and parts
Check for damaged or worn parts
Inspect and clean unit and labels
Clean air filter
Replace spark plug
Replace fuel filter
Check muffler mounting screws
_,WARNING: Avoid touching muf-
fler unless engine and muffler are cold.
A hot muffler can cause serious burns.
WHEN TO PERFORM
Before each use
Before each use
After each use
Every 5 hours of operation
Yearly
Yearly
Yearly
_b WARNING: This unit is intended
for blower use only. Do not attempt to
open inlet cover. Opened or damaged
-7-
inlet cover can result in serious injury.
Discontinue use of blower immediately
if inlet cover becomes opened or dam-
aged. Take unit to your nearest Sears
Service Center for repair.
GENERAL RECOMMEN DATIONS
The warranty on this unit does not cov-
er items that have been subjected to
operator abuse or negligence. To re-
ceive full value from the warranty, the
operator must maintain unit as instruct-
ed in this manual. Various adjustments
will need to be made periodically to
properly maintain your unit.
CHECK FOR LOOSE
FASTENERS AND PARTS
• Spark Plug Boot
• Air Filter
• Housing Screws
CHECK FOR DAMAGED OR
WORN PARTS
Contact Sears Service Center for re-
placement of damaged or worn parts.
• Throttle Lever - Ensure throttle lever
functions properly by moving the
throttle lever to the STOP position.
Make sure engine stops; then restart
engine and continue.
• Fuel Tank - Do not use unit if fuel tank
shows signs of damage or leaks.
INSPECT AND CLEAN UNIT
AND LABELS
• After each use, inspect complete unit
for loose or damaged parts. Clean
the unit using a damp cloth with a
mild detergent.
• Wipe off unit with a clean dry cloth.
CLEAN AIR FILTER
Cleaning the air filter:
1. Clean the cover and the area
around it to keep debris from falling
into the carburetor chamber when
the cover is removed.
2. Remove parts as illustrated.
NOTE: Do not clean filter in gasoline
or other flammable solvent. Doing so
can create a fire hazard or produce
harmful evaporative emissions.
3. Wash the filter in soap and water.
4. Allow filter to dry.
5. Apply a few drops of oil to the filter;
squeeze filter to distribute oil.
6. Replace parts.
REPLACE SPARK PLUG
Replace spark plug each year to ensure
the engine starts easier and runs better.
Set spark plug gap at 0.025 inch. Igni-
tion timing is fixed, nonadjustable.
1. Twist, then pull off spark plug boot.
2. Remove spark plug from cylinder
and discard.
3. Replace with Champion CJ-6Y
spark plug and tighten securely
with a 3/4 inch socket wrench.
4. Reinstall the spark plug boot.
REPLACE FUEL FILTER
To replace fuel filter, drain unit by run-
ning it dry of fuel, then remove fuel
cap/retainer assembly from tank. Pull
filter from tank and remove it from the
fuel line. Install new fuel filter on fuel
line; reinstall parts.
_7¸_
i.9
_" /Air Filter
_i_ Air Filter
i_._,,,_ Cover
Screws
A dirty air filter decreases engine per-
formance and increases fuel consump-
tion and harmful emissions. Always
clean after every 5 hours of operation.
Fuel Filter
CHECK MUFFLER MOUNTING
SCREWS
Once each year, ensure muffler
mounting screws are secure and tight-
ened properly to prevent damage.
Mounting Screw
Holes
Muffler Cover
Screws
-8-
1. Loosen and remove the 2 screws
from the muffler cover.
2. Remove the muffler cover.
3. Tighten the 2 muffler mounting
screws securely.
4. Reinstall muffler cover and 2
screws. Tighten securely.
CARBURETOR ADJUSTMENT
There is no screw for idle adjustment
on your blower. The throttle lever is
used to control engine speed. The
throttle lever can be placed in one of
four positions: STOP, IDLE or -iF,
FULLTHROTTLE or '(_, and one inter-
mittent position. If your engine will
not run properly or you require further
assistance, contact your Sears Service
Center or call our customer assistance
help line at 1-800-235-5878.
41 WARNING: Perform the following
steps after each use:
• Allow engine to cool, and secure the
unit before storing or transporting.
• Store unit and fuel in a well venti-
lated area where fuel vapors cannot
reach sparks or open flames from
water heaters, electric motors or
switches, furnaces, etc.
• Store unit with all guards in place.
Position unit so that any sharp object
cannot accidentally cause injury.
• Store unit and fuel well out of the
reach of children.
SEASONAL STORAGE
Prepare unit for storage at end of sea-
son or if it will not be used for 30 days
or more.
If your unit is to be stored for a period
of time:
• Clean the entire unit before lengthy
storage.
• Store in a clean dry area.
• Lightly oil external metal surfaces.
FUEL SYSTEM
Under FUELING ENGINE in the OPERA-
TION section of this manual, see mes-
sage labeled IMPORTANT regarding
the use of gasohol in your engine.
Fuel stabilizer is an acceptable alterna-
tive in minimizing the formation of fuel
gum deposits during storage. Add stabi-
lizer to gasoline in fuel tank or fuel stor-
age container. Follow the mix instruc-
tions found on stabilizer container. Run
engine at least 5 minutes after adding
stabilizer.
Craftsman 40:1,2-cycle engine oil (air
cooled) is already blended with fuel
stabilizer. If you do not use this Sears
oil, you can add a fuel stabilizer to your
fuel tank.
ENGINE
• Remove spark plug and pour 1 tea-
spoon of 40:1,2-cycle engine oil (air
cooled) through the spark plug open-
ing. Slowly pull the starter rope 8 to
10 times to distribute oil.
• Replace spark plug with new one of
recommended type and heat range.
• Clean air filter.
• Check entire unit for loose screws,
nuts, and bolts. Replace any dam-
aged, broken, or worn parts.
• At the beginning of the next season,
use only fresh fuel having the proper
gasoline to oil ratio.
OTHER
• Do not store gasoline from one sea-
son to another.
• Replace your gasoline can if it starts
to rust.
-9-
TROUBLESHOOTING TABLE
WARNING: Always stop unit and disconnect spark plug before perform-
ing any of the recommended remedies below other than remedies that re-
TROUBLE
Engine will not
start.
quire operation of the unit.
CAUSE
1. Engh_eflooded,
Engine will not
idle properly.
Engine will not
accelerate,
lacks power, or
dies under a
load.
Engine smokes
excessively.
Engine runs hot.
2. Fuel tank empty.
3. Spark plug not firing.
4. Fuel not reaching
carburetor.
5. Compression low. 5.
1. Fuel not reaching 1.
carburetor.
2. Carburetor requires 2.
adjustment.
3. Crankshaft seals worn. 3.
4. Compression low. 4.
1. Air filter dirty. 1.
2. Fuel not reaching 2.
carburetor.
3. Spark plug fouled. 3.
4. Carburetor requires 4.
adjustment.
5. Carbon build up. 5.
6. Compression low. 6.
1. Choke partially on. 1.
2. Fuel mixture incorrect. 2.
3. Air filter dirty. 3.
4. Carburetor requires 4.
adjustment.
1. Fuel mixture incorrect. 1.
2. Spark plug incorrect. 2.
3. Carburetor requires 3.
adjustment.
4. Carbon build up. 4.
REMEDY
1. See "Starting a Flooded Engine"
in Operation section.
2. Fill tank with correct fuel mixture.
3. Install new spark plug.
4. Check for dirty fuel filter; replace.
Check for kinked or split fuel line;
repair or replace.
Contact Sears Service (see back cover).
Check for dirty fuel filter; replace.
Check for kinked or split fuel line;
repair or replace.
Contact Sears Service (see back cover).
Contact Sears Service (see back cover).
Contact Sears Service (see back cover).
Clean or replace air filter.
Check for dirty fuel filter; replace.
Check for kinked or split fuel line;
repair or replace.
Clean or replace spark plug
and re-gap.
Contact Sears Service (see back cover).
Contact Sears Service (see back cover).
Contact Sears Service (see back cover).
Adjust choke.
Empty fuel tank and refill with
correct fuel mixture.
Clean or replace air filter.
Contact Sears Service (see back cover).
See "Fueling Engine" in Operation
section.
Replace with correct spark plug.
Contact Sears Service (see back cover).
Contact Sears Service (see back cover).
-10-