Craftsman 917.25081 User manual

Operator's Manual
19.0 HR* 42" Mower
Electric Start
Automatic Transmission
Model No.
917.25081
•EspaSol, p. 33
I_ his product has a low emission engine which operates
differently from previously built engines. Before you start the
engine, read and understand this manual.
IMPORTANT:
Read and follow atl Safety
Rules and Instructions before
operating this equipment.
For answers to your questions
about this product, call:
1-888-331-4569
Craftsman Customer Help Line
Sears Brands Management Corporation, Hoffman Estates, tL 60179 U.S.A.
Visit our Craftsman website: www,craftsman.com
* The powet r_ing as desiared bythe engine manufacturer isthe * La potenc_a nominaJ declareda por elfabr_cacte del motor es la
average gross power output at the specked RPM of a typical ealida medla do potencia brata alos RPM espectficadas de un
production engine for the engine model measured using SAE motor do eerie tfptco pare el modelo de motor, medida eag/,n
Standards for engine gross power. Please refer to the engine los no_mas SAE sob_e potencie br,Jta de motor. Pa,,a m&s
mentJfacturer for details, informacl6n, consu_teal fabdcante del motor.
588134349

Warranty .................................................. 2
Safety Rules ............................................ 3
Product Specifications ............................. 6
Assembly/Pre-Operation ......................... 7
Operation ................................................. 9
Maintenance Schedule .......................... 16
Maintenance ........................................... 16
Service and Adjustments ....................... 21
Storage .................................................. 27
Troubleshooting ..................................... 28
Sears Service ......................... Back Cover
CRAFTSMAN LIMITED WARRANTY
FOR TWO YEARS from the date of purchase, all non-expendable parts of this riding equipment are
warranted against any defects in material or workmanship. With proof of purchase, a defective non-
expendable part will receive free in-home repair or replacement at option of seller.
BATTERY LIMITED WARRANTY
FOR 90 DAYS from the date of purchase, the battery (an expendable part) of this riding equipment is
warranted against any defects in material or workmanship. Wffh proof Of purchase, a new battery will be
supplied free of charge. You are responsible for the labor cost of battery installation,
ADDITIONAL LIMITED WARRANTIES
In the following additional warranties, you are responsible for the tabor cost of part installation after the
second year from the date of purchase.
FOR FIVE YEARS from the date of purchase, the frame of this riding equipment is warranted against any
defects in material or workmanship. With proof of purchase, anew frame wilt be supplied free of charge,
FOR TEN YEARS from the date of purchase, the front axle of this riding equipment is warranted against any
defects in material or workmanship. With proof of purchase, anew front axle will be supplied free of charge.
FOR AS LONG AS IT !S USED by the original owner after the tenth year from the date of purchase, the
cast iron front axle (if equipped) of this riding equipment is warranted against any defects in material or
workmanship. With proof of purchase, a new cast iron front axle will be supplied free of charge.
WARRANTY SERVICE
For warranty coverage details to obtain free repair or replacement, call 1-888-331-4569 or visit the web
page: www.craftsman.com/warranty
In ali cases above, if part repair or replacement is impossibie, the riding equipment will be replaced free of
charge with the same or an equivalent model.
All of the above warranty coverage is void if this dding equipment is ever used while providing commercial
services or if rented to another person,
This warranty covers ONLY defects in material and workmanship. Warranty coverage does NOT
include:
•Expendable parts (except battery) that can wear out from normal use within the warranty period, including
but not limited to blades, spark plugs, air cleaners, belts, and oil _ters.
• Standard maintenance servicing, oi] changes, or tune-ups.
• Tirerep_a_ement_rrepaircausedbypuncturesfr_m_utside_bjects_suchasnai_s_th_ms's_umps__rg]ass.
• Tire or wheel replacement or repair resulting from normal wear, accident, or improper operation or
maintenance.
• Repairs necessary because of operator abuse, including but not limited to damage caused by towing
objects beyond the capability of the riding equipment, impacting obiects that bend the frame, axle
assembly or crankshaft, or over-speeding the engine.
• Repairs necessary because of operator negligence, including but not limited to, electricaI and mechanical
damage caused by improper storage, failure to use the proper grade and amount of engine oil, failure
to keep the deck clear of flammable debris, or failure to maintain the riding equipment according to the
instructions contained in the operator's manual.
• Engine (fuel system) cleaning or repairs caused by fuel determined to be contaminated or oxidized
(stale). tn general, fuel should be used within 30 days of its purchase date.
• Normal deterioration and wear of the exterior finishes, or product label replacement.
This warrantygivesyou specific legaldghts,andyoumay alsohaveother rightswhichvaryfromstatetostate.
Sears Brands Management Corporation, Hoffman Estates, IL 60179
2

_DANGER: This cutting machine is capable of amputating hands and feet and
throwing objects. Failure to observe the following safety instructions could result
in serious injury or death.
A(_WARNING: Inorderto prevent acciden-
tal starting when setting up, transporting,
adjusting or making repairs, always discon-
nect spark plug wire and place wire where
it cannot contact spark plug.
_WARNING: Do not coast down a hill in
neutral, you may lose control of the tractor.
_WARNING: Tow only the attachments
that are recommended by and comply with
specifications of the manufacturer of your
tractor. Use common sense when towing.
Operate only at the lowest possible speed
when on a slope. Too heavy ofa load, while
on a slope, is dangerous. Tires can lose
traction with the ground and cause you to
lose control of your tractor.
_WARNING: Engine exhaust, some of
itsconstituents, and certain vehicle compo-
nents contain or emit chemicals known to
the State of California to cause cancer and
birth defects or other reproductive harm.
_IbWARNING: Battery posts, terminals and
related accessories contain lead and lead
compounds, chemicals knownto the State of
California to cause cancer and birth defects
or other reproductive harm. Wash hands
after handling.
I. CHILDREN
_(_WARNING! CHILDREN CAN BE IN-
JURED BYTHIS EQUIPMENT. TheAmeri-
can Academy of Pediatrics recommends
that children be a minimum of t2 year of
agebefore operating apedestrian controlled
lawn mower and a minimum of 16 years of
age before operating a riding lawnmower.
_WARNING! CHILDREN CAN BE
SERIOUSLY INJURED OR KILLED BY
THIS EQUIPMENT. Carefully read and
follow all of the safety instructions below.
Tragic accidents can occur if the operator
is not alert to the presence of children.
Children are oftenattracted to the machine
and the mowing activity. Never assume
that children will remain where you last
saw them.
•Keep children out of the mowing area
and inthe watchfulcare ofa responsible
adult other than the operator.
•Be alert and turn machine off if a child
enters the area.
• Before and while backing, look behind
and down for small children.
• Never carry children, even with the
blades shut off. They may fall off and
be seriously injured or interfere with safe
machine operation. Children who have
beengiven ridesinthe past may suddenly
appear in the mowing area for another
ride and be run over or backed over by
the machine.
• Never allow children to operate the ma-
chine.
•Use extreme caution when approaching
blind corners, shrubs, trees, or other
objects that may block your view of a
child,
IL GENERAL OPERATION
- Read,understand, andfo]low all instruc-
tions on the machine and in the manual
before starting.
• Do not put hands or feet near rotating
parts or under the machine, Keep clear
of the discharge opening at all times.
• Only allow responsible adults, who are
familiar with the instructions, to operate
the machine.
• Clearthe area of objects such as rocks,
toys, wire, etc., which could be picked
up and thrown by the blades.
• Ensure the area is clear of bystanders
beforeoperating. Stop machine ifanyone
enters the area.
•Never carry passengers.
• Do not mowin reverse unless absolutely
necessary. Alwayslook down and behind
before and while backing,
• Neverdirect discharged materialtoward
anyone, Avoid discharging material
against a wall or obstruction, Material
may ricochet back toward the operator.
Stop the blades when crossing gravei
surfaces.
• Donot operate machine withoutthe entire
grass catcher, discharge chute, or other
safety devices in place and working.

•Slowdown beforetuming.
•Never leave a running machine unat-
tended. Always turn off blades, set
parking brake, stop engine, and remove
keys before dismounting.
•Disengage blades when not mowing.
Shut off engine and wait for all parts to
come to acomplete stop before cleaning
the machine, removing the grass catcher,
or unclogging the discharge chute.
• Operate machine onlyin daylightorgood
artificial light.
•Do not operate the machine while under
the influence of alcohol or drugs.
•Watch for traffic when operating near or
crossing roadways.
•Use extreme caution when loading or
unloading the machine into a trailer or
truck.
•Always wear eye protection when operat-
ing machine.
• Use ear protectors to avoid damage to
hearing.
• Data indicates that operators, age 60
years and above, are involved in a large
percentage of riding mower-related inju-
ries. These operators should evaluate
their ability to operate the riding mower
safely enough toprotect themselves and
others from serious injury.
•Followthe manufacturer's recommenda-
tionfor wheel weights or counterweights.
•Keep machine free of grass, leaves or
other debris build-upwhich cantouch hot
exhaust/engine parts and burn. Do not
allow the mower deck to plow leaves or
other debris which can cause build-up
to occur. Clean any oil or fuel spillage
before operating or storing the machine.
Allow machine to coot before storage.
Iil. SLOPE OPERATION
_WARNING! When loading or unloading
this machine, do not exceed the maximum
recommended operation angle of 15°.
Slopes are a major factor related to loss of
control and tip-over accidents, which can
result in severe injury or death. Operation
on all slopes requires extreme caution. If
you cannot back up the slope or ifyou feel
uneasy on it, do not mow it.
-Mow up and down slopes, not across.
• Watch for holes, ruts, bumps, rocks, or
other hidden objects. Uneven terrain
could overturn the machine. Tall grass
can hide obstacles.
•Choose a low ground speed sothat you
will not have to stop or shift while on the
slope.
•Do not mow on wet grass. Tires may
lose traction. Always keep the machine
in gear when going down slopes.
, Do notshiftto neutral andcoastdownhitl.
• Avoid starting, stopping, or turning on a
slope. Ifthetires Iosetraction, disengage
the blades and proceed slowly straight
down the slope.
•Keep all movement on the slopes slow
and gradual. Do not make sudden
changes in speed or direction, which
could cause the machine to roll over.
•Use extreme caution while operating
machine with grass catchers or other
attachments; they can affect the stabil-
ity of the machine. Do no use on steep
slopes.
•Do not try to stabilize the machine by
putting your foot on the ground.
•Do not mow near drop-offs, ditches,
or embankments. The machine could
suddenly roll over if a wheel is over the
edge or if the edge caves in.
• If machine stops while going uphill,
disengage blades, shift into reverse and
back down slowly.
•Do not turn onslopes unless necessary,
and then, turn slowly and gradually
downhill, if possible.
IV. TOWING
• Towonly with a machine that has a hitch
designed for towing. Donot attach towed
equipment except at the hitch point.
• Follow the manufacturer's recommenda-
tion for weight limits for towed equipment
and towing on slopes.
• Never allow children or others in or on
towed equipment.
• Onslopes, the weight ofthetowed equip-
ment may causeloss oftraction andloss
of control.
• Travel slowly and allow extra distance to
stop.

V. SERVICE
SAFE HANDLING OF GASOLINE
To avoid personal injury or property dam-
age, useextreme care in handling gasoline.
Gasoline is extremely flammable and the
vapors are explosive.
•Extinguish all cigarettes, cigars, pipes,
and other sources of ignition.
•Use only approved gasoline container,
•Never remove gas cap or add fuel with
the engine running.
•Allow engine to cool before refueling.
• Never fuel the machine indoors,
•Neverstorethe machineorfuelcontainer
where there is an open flame, spark, or
pilot light such as on a water heater or
other appliances.
• Never fil! containers inside a vehicle or
on a truck or trailer bed with plastic liner.
Always place containers on the ground
away from your vehicle when filling.
-Remove gas-powered equipment from
the truck or trailer and refuel it on the
ground. Ifthis isnot possible, then refuel
such equipmentwith aportable container,
rather than from a gasoline dispenser
nozzle.
•Keep the nozzle in contact with the rim
of the fuel tank or container opening at
all times untilfueling iscomplete. Do not
use a nozzle lock-open device.
•Iffuelis spilled onclothing, change cloth-
ing immediately,
•Never overfill fuel tank. Replace gas cap
and tighten securely.
GENERAL SERVICE
•Never operate machine in a closed area.
• Keep allnutsand botts tighttoensurethe
equipmentisin safe workingcondition,
o Nevertamperwithsafe'_tdevices. Never
interferewiththe intended functionof a
safety device or reduce the protection
providedbyasafetydevice.Check there
properoperation regularly.NEVER oper-
ate a machine with a safety devicethat
does not function properly.
• Keep machinefree ofgrass, leaves, or
other debris build-up, Clean oil or fuel
spillage and remove any fuel-soaked
debris, Allow machine to cool before
storing.
• If you strike aforeign object, stop and
inspectthemachine. Repair,ifnecessary,
before restarting.
•Never make any adjustments or repairs
with the engine running.
•Checkgrasscatchercomponents andthe
discharge chute frequentlyand replace
with manufacturer's recommended parts,
when necessary.
• Mower blades aresharp. Wrapthe blade
orwear gloves, and use extreme caution
when servicing them.
•Checkbrakeoperationfrequently. Adjust
and service as required.
o Maintain or replace safety and instruction
labels, as necessary.
Use ear protectors to avoid damage to hearing.
Always wear eye protection when operating machine.

PRODUCTSPECIFICATIONS
Gasoline Capacity 2.5 Gallons 19,46 L
and type: Regular Unleaded *
Oil Type: SAE 30 (above 32°F/0°C)
(APt: SG-SL} SAE 5W30 (below 32°F10°C
Oil Capacity: WI Filter: 56 Oz. !1,65 L
W/out Filter: 48 Oz. /1,4 L
Spark Plug: Champion RC12YC
(Gap: ,030"10,76 mm)
Charging ,3Amps Battery
System: 5 Amps Headlights
Battery: AmplHr: 28
Min, CCA: 230
Case size: U1R
Blade Bolt Torque; 45-55 F_. Lbs./62-75 Nm
&Gasoline containing up to 10% ethanol (El0) is
acceptable for use in this machine, The usa of
any gasoline exceed{ng "_0%ethanol (Et0) will
void the productwarranty,
CONGRATULATIONS on your purchase of
a new tractor. It has been designed, engi-
neered and manufactured to gJveyouthe best
possible dependability and performance.
Should you experience any problem you can-
not easily remedy, please contact a Sears or
other qualified service center. We have com-
petent, well-trained representatives and the
proper tools to service or repair this tractor.
Please read and retain this manual. The
instructions will enable you to assemble
and maintain your tractor properly. Always
observe the "SAFETY RULES".
CUSTOMER RESPONSIBILITIES
•Read and observe the safety rules.
- Follow a regular schedule in maintaining,
caring for and using your tractor.
- Follow instructions under "Maintenance"
and "Storage" sections of this manuaL.
•Wear proper Personal Protective Equip-
ment _PPE)while operating this machine,
including(ata minimum) sturdy footwear,
eye protection, and hearing protection.
Do not mow in shorts and/or open toed
footwear.
• Always letsomeone knowyou areoutside
mowing.
A(_.WARNING: This tractorisequippedwith
an internal combustion engine and should
not be used on or near any unimproved
forest-covered, brush-covered or grass-
covered land unless the engine's exhaust
system is equipped with a spark arrester
meeting applicable local or state laws (if
any). If a spark arrester is used, it should
be maintained in effective working order by
the operator.
Inthe state ofCalifornia the above isrequired
bylaw (Section 4442 ofthe California Public
Resources Code), Other states may have
similar laws. Federal laws apply on federal
lands. A spark arrestor for the muffler is
availablethrough yournearest Sears service
center (See REPAIR PARTS manual).
REPAIR PROTECTION AGREEMENTS
Congratulations on making a smart pur-
chase. Your new Craftsman® product is
designed and manufactured for years of
dependable operation. But like all products,
itmay require repairfrom time totime.That's
when havingaRepair ProtectionAgreement
can save you money and aggravation.
Purchase a Repair Protection Agreement
now and protect yourseff from unexpected
hassle and expense.
Herds what's included in the Agreement'.
• Expertservice byour 12,000 professional
repair specialists,
• Unlimited service and no charge for parts
and labor on all covered repairs.
• Product replacement if your covered
product can't be fixed.
• Discount of 25% from regular price of
service and service-related parts not
covered by the agreement; also, 25% off
regular price of preventive maintenance
check.
- Fast help by phone -phone support
from a Sears representative on products
requiring in-home repair, plus convenient
repair scheduling.
Once you #urchasethe Agreement, a simple
phone call is all that it takes for you to sched-
ule service. You can callanytime day or night,
or schedule a service appointment online.
Sears has over 12,000 professional repair
specialists, who have access to over 4.5
million quality parts and accessories. That's
the kind of professionalism you can count on
to help prolong the life of your new purchase
for years to come, Purchase your Repair
Protection Agreement today!
Some limitations and exclusions apply.
For prices and additional information call
1-800-827-6655,
SEARS INSTALLATION SERVICE
For Sears professional installation of home
appliances, garage door openers, water
heaters, and other major home items, in the
U.S.A, call 1-8004-MY-HOME®.

Keys
Key(s)
Slope Sheet
(1) Oil DrainTube
(1) Quick
Connect !
Your new tractor has been assembled at the factory with exception of those parts left
unassembled for shipping purposes.
TOOLS REQUIRED FOR ASSEMBLY
A socket wrench set will make assembly
easier. Standard wrench sizes are listed.
(1) 1/2" wrench Tire pressure gauge
(2) 7/t6" wrenches Utility knife
Pliers
When right or left hand is mentioned in this
manual,itmeanswhenyouareintheoperating
position (seated behind the steering wheel).
TO REMOVE TRACTOR FROM
CARTON
UNPACK CARTON
• Remove all accessible loose parts and
parts cartons from carton.
- Cut along dotted lines on all four panels
of carton. Remove end panels and lay
side panels flat.
•Check for any additional loose parts or
cartons and remove.
TO ADJUST SEAT
• Sit in seat.
• LAup adjustment lever (A)and slideseat
until a comfortable position is reached
which allows you to press clutch/brake
pedal all the way down.
• Release lever to lock seat in position,
BEFORE REMOVING TRACTOR
FROM SKID
TO CHECK BATTERY
1, Liftseat to raised position.
NOTE: Ifthis battery is put into service after
month and year indicated on label (label is
located between terminals) charge battery
for minimum of onehour at 6-10 amps. (See
"BATTERY" in Maintenance section of this
manual for charging instructions).
•For battery and battery cable installation
see "REPLACING BATTERY" in the
"Service and Adjustments" section in this
manual.
NOTE: You may now roll your tractor off the
skid. Continue using the instructionsthat
follow to remove the tractor from the skid.
WARNING: Before starting, read, un-
derstand and follow all instructions in the
Operation section of this manual. Be sure
tractor is in a well-ventilated area. Be sure
the area in front of tractor is clear of other
people and objects.

TO ROLL TRACTOR OFF SKID (See
Operation section for location and
function of controls)
1. Raise attachment liftlever to itshighest
position.
2. Release parking brake by depressing
clutch/brake pedal.
S. Place freewheel control Jn"transmission
disengaged position" (See "TO TRANS =
PORT" in the Operation section o1this
manual).
4. Roll tractor forward off skid.
5. Remove banding holding the deflector
shield up against tractor.
Continue with the instructionsthat follow.
CHECK TIRE PRESSURE
The tires onyourtractor were overlnflatedat
the factory for shipping purposes. Correct
tire pressure is importantfor best cutting
performance.
•Reduce tire pressure to PSI shown on
tires.
CHECK DECK LEVELNESS
For best cutting results, mower housing
should be properly leveled. See "TO LEVEL
MOWER" in the Service and Adjustments
section of this manual.
CHECK FOR PROPER POSITION OF
ALL BELTS
See the figures that are shown for replacing
motion and mower blade drive belts in the
Service andAdjustments sectionofthis man-
ual. Veriiy that the belts are routed correctly.
CHECK BRAKE SYSTEM
After you learn how to operate your tractor,
check to see that the brake is operating
properly. See 'q'O CHECK BRAKE" in the
Service and Adjustments section of this
manual.
V(CHECKLIST
Before you operate your new tractor, we
wish to assure that you receive the best
performance and satisfaction from this
Quality Product.
Please review the following checklist:
V"All assembly instructions have been
completed.
J" No remaining loose partsin carton.
v/ Batteryisproperly prepared and charged.
J" Seat is adjusted comfortably and tight-
ened securely.
d' All tires are properly inflated. (For ship-
ping purposes, the tires were overinflated
at the factory).
J Ensure mower deck is propedy leveled
side-to-side/front-to-rear for best cutting
results. (Tires must be propedy inflated
for leveling).
J" Check mower and drive belts. Ensure
they are routed properly around pulleys
and inside alt belt keepers.
d" Checkwiring. Seethatall connections are
stillsecureandwiresareproperiyclamped.
J Before driving tractor, be sure freewheel
control isin "transmission engaged" posi-
tion (see "ToTransport" in the Operation
section of this manual).
While learninghowto useyourtractor,payex-
traattentiontothe following importantitems:
d" Engine oil is at proper level.
vf Fueltank isfilledwith fresh, clean, regular
unleaded gasoline.
#' Become familiar with all controls, their
location and function. Operate them
before you start the engine.
t/Ensure brake system isin safe operating
condition.
!/Ensure Operator Presence System and
Reverse Operation System (ROS) are
working properly (Seethe Operation and
Maintenance sections in this manual).

Thesesymbolsmayappearonyourtractororinliteraturesuppliedwiththeproduct.Learn
andunderstandtheirmeaning.
R N H Ikl
REVERSE NEUTRAL HIGH LOW CHOKE IGNITION
SWITCH
ENGINE ENGINE ENGINE DIFFERENTIAL
OFF START ON LOCK CLUTCH/ MOWER
BRAKE PEDAL LIFT
FAST SLOW
PARKING MOWER
BRAKE HEIGHT
1'114
q_
REVERSE
OPERATION
SYSTEM (ROS)
,I;
€
REVERSE FORWARD CRUISE CONTROL LIGHTS ON FUEL BATTERY EAR
PROTECTION
RECOMMENDED
ATTACHMENT ATTACHMENT DANGER, KEEP
CLUTCH CLUTCH HANDS AND
DISENGAGED ENGAGED FEET AWAY
®@@@@
KEEP AREA CLEAR SLOPE HAZARDS
(SEE SAFETY RULES SECTION)
FREEWHEEL
(Automatic Models only)
&
Failure to follow instructions
couldresult in serious injure/or
death. The safety alert symbol
is used to identify safety inform-
ation about hazards which can
result in death, serious injury
and/or property damage.
&
&
&
DANGER indicates a hazard which, if not avoEded,
will result In death or serious injury.
WARNING indicates ahazard which, if not avoided,
could Pesult tn death or serious injury.
CAUTION indicates a hazard which, if not avoided,
might result in minor or moderate intury.
CAUTION when used without the aled symbol.
indicates asituation that could result in damage
to the tractor and/or engine,
HOT SURFACES indicates a hazard which,
if not avoided, could result in death, serious
injury and/or property damage.
FIRE indicates a hazard which, if not avoided,
could result In death, serious injury and/or
property damage.
•9

KNOW YOUR TRACTOR
READ THIS OPERATOR'S MANUAL AND SAFETY RULES BEFORE OPERATING
YOUR TRACTOR
Compare the illustrations withyour tractorto familiarize yourself with the locationsofvarious
controls and adjustments. Save this manual for future reference.
/_ \"_
Our tractors conform to the applicable safety standards of the
American National Standards Institute.
(A) ATTACHMENT LIFT LEVER - Used to
raise and lower the mower or other attach-
merits mounted to your tractor.
(B) CLUTCH/BRAKE PEDAL - Used for
declutching and braking the tractor and
starting the engine.
(C) PARKING BRAKE- Locks dutch/brake
pedal into the brake position.
(D) THROTtLE/CHOKE CONTROL- Used
for starting and controlling engine speed.
(E) ATTACHMENTCLUTCH LEVER- Used
toengagethe mower blades, orother attach-
ments mounted to your tractor.
(F) IGNITION SWITCH - Used for starting
and stopping the engine.
(G) REVERSE OPERATION SYSTEM
(ROS) "ON" POSITION - Allows operation
ofmower orother powered attachment while
in reverse.
(H) LIGHT SWITCH - Turnsthe headlights
on and off.
(J) MOTION CONTROL LEVER - Selects
the speed and direction oftractor,
(M) FREEWHEEL CONTROL- Disengages
transmission for pushing ors[owlytowing the
tractor with the engine off.
t0

The operation of any tractor can result in foreign objects thrown into
the eyes, which can result in severe eye damage. Always wear safety
glasses or eye shields while operating your tractor or performing any
adjustments or repairs. We recommend standard safety glasses or a
wide vision safety mask worn over spectacles.
HOW TO USE YOUR TRACTOR
TO SET PARKING BRAKE
Your tractor is equipped with an operator
presence sensing switch. When engine
is running, any attempt by the operator to
leavethe seat withoutfirst setting the parking
brake wilt shut off the engine.
1. Depress clutch/brake pedal (B) all the
way down and hold.
2, Pult parking brake lever (C) up and hold,
release pressure from clutch/brake pedal
(B), then release parking brake lever.
Pedal should remain in brake position,
Ensure parking brake will hold tractor
secure.
• Turn ignitionkey (F) to "STOP" position
andremove key.Always remove keywhen
leavingtractorto preventunauthorized use.
• Never use choke to stop engine.
IMPORTANT: Leavingthe ignitionswitch in
any position other than "STOP" will cause
the battery to discharge and go dead.
NOTE: Undercertain conditions whentractor
is standing idle with the engine running, hot
engine exhaust gases may cause "brown-
ing" of grass. To eliminate this possibility,
always stop engine when stoppingtractor
on grass areas.
ACAUTION: Always stop tractor com-
pletely, as described above, before leaving
the operator's position.
TO USE THROTTLE CONTROL (D)
Always operate engine at full speed (fast).
•Operating engine at less than full speed
(fast)reducesengine'soperatingefficiency.
•Full speed (fast) offers the best mower
performance.
STOPPING
MOWER BLADES -
• To stop mower blades, move attachment
clutch controlto disengaged position (t_).
(1"_11)Attachment (tr_l) Attachment
Clutch Control Clutch Control
"Engaged .... Disengaged"
GROUND DRIVE -
•To stop ground drive, depress brake pedal
all the way down,
•Move motion control lever to neutral posi-
tion.
ENGINE -
•Movethrottle control (D) between halfand
full speed (fast) position.
NOTE: Failure to move throttle control be-
tween half andfull speed (fast) position,be-
forestopping, may cause engineto"backfire". 11
TO MOVE FORWARD AND
BACKWARD
The direction and speed of movement is
controlled by the motion control lever, (J)
1. Start tractor with motion control lever in
neutralposition.
2. Release parking brake.
3. Slowly move motion control lever to
desired position.

TO ADJUST MOWER CUTTING HEIGHT
The position of the attachment liftlever (A)
determines the cutting height.
°Put attachment lift lever in desired cutting
height slot.
The cutting height range is approximately 1
to 4" (25,4 to 101,6 ram)..The heights are
measured from the ground to the blade tip
with the engine not running. These heights
are approximate and may vary depending
upon soil conditions, height of grass and
types of grass being mowed.
• Theaverage lawn should becutto approxi-
mately 2-1/2" (63,5 mm) during the cool
season and to over 3" (76,2 mm) during
hot months. For healthier and better look-
ing lawns,mow often and after moderate
growth.
• For best cutting performance, grass over
6" (152,4 ram) in height should bemowed
twice. Makethe first cut relatively high; the
second to desired height.
TO ADJUST GAUGE WHEELS
Gauge wheels are properly adjusted when
theyare slightly offthe ground when mower
is atthe desired cutting height in operating
position. Gauge wheels then keep the deck
in proper/position to help prevent scalping
in most terrain conditions.
NOTE: Adjust gauge wheels with tractor on
a fiat leve_surface,
1. Adjust mower to desired cutting height
(See "TO ADJUST MOWER CUTTING
HEIGHT" in this section of manual).
2. With mower indesired height of cutposi-
tion, gauge wheeis shouId beassembled
sothey are slightly off the ground. Install
gauge wheel inappropriate hole.Tighten
securely.
3. Repeat for all, installing gauge wheel in
same adjustment hole.
TO OPERATE MOWER
Your tractor is equipped with an operator
presence sensing switch. Any attempt
by the operator to leave the seat with the
engine running and the attachment clutch
engaged will shut off the engine. You must
remain fully and centrallypositioned in the
seatto prevent the engine fTOmhesitating or
cutting off when operating your equipment
on rough, rolling terrain or hills.
1. Select desired height of cut with attach-
ment lift lever.
2, Start mower blades byengaging attach-
ment clutch control.
TO STOP MOWER BLADES
Disengage attachment clutch control.
_CAUTION: Do not operate the mower
without either the entire grass catcher, on
mowers so equipped, orthe deflector shield
in place.
REVERSE OPERATION SYSTEM (ROS)
Your tractor is equipped with a Reverse
Operation System (ROS). Any attempt by
the operator to travel inthe reverse direction
with the attachment clutch engaged will shut
off the engine unless ignition key is placed
in the ROS "ON" position.
all'WARNING: Backing up with the at-
tachment clutch engaged while mowing is
stronglydiscouraged, Turningthe ROS"ON",
to allow reverse operation with the attach-
ment clutch engaged, should only be done
when the operator decides it is necessary to
reposition the machine w_ththe attachment
engaged, Do not mow in reverse unless
absolutely necessary,
12

USINGTHEREVERSEOPERATION
SYSTEM-
Onlyuseifyouarecertainnochildrenor
otherbystanderswillenterthemowingarea.
1.Movemotioncontrollevertoneutral
position.
2.Withenginerunning,turnignitionkey
counterclockwisetoROS"ON"position,
3. Lookdownandbehindbeforeandwhile
backing,
4. Slowlymovemotioncontrolleverto
reverse(R)positiontostartmovement.
5,WhenuseoftheROSisnolongerneeded,
turntheignitionkeyclockwisetoengine
"ON"position.
ROS"ON"Engine"ON"Position
Position(NormalOperating)
TO OPERATE ON HILLS
_WARNING: Do not drive up or down
hills with slopes greater than 15°and do not
drive across any slope. Use the slope guide
provided at the back of this manual.
•Choosetheslowestspeed before starting
up or down hills.
-Avoid stopping or changing speed onhills.
•Ifstopping is absolutely necessary, push
clutch/brake pedalquickly tobrake position
and engage parking brake.
•Move motion control teverto neutral posi-
tion.
IMPORTANT: The motion control lever does
not return toneutral positionwhen the clutch/
brake pedal is depressed.
•Torestart movement, slowly release park-
ing brake and clutch/brake pedal.
•Slowly move motion control lever to
slowest setting,
- Make all turns slowly.
TO TRANSPORT
When pushing or towing your tractor, be
sure to disengage transmission by placing
freewheel control in freewheeling position.
Free wheel control is located at the rear
drawbar of tractor.
1.Raise attachment lift to highest position
with attachment lift control.
2. Move motion control lever into the NEU-
TRAL position to release tension from
transmission.
NOTE: To completely release tension from
transmission,it may be necessary to move
motion control lever (J) into the REVERSE
position first and then shift forward into the
NEUTRAL position.
Neutral (__..zL-...'%.
Pos.o.
3.Pull freewheel control out until the free
wheelcontrolrodlocksinextendedposition.
4.Do not push or tow tractor at more than
two (2) mph (3,2 kin/h).
5.Toreengage transmission, reverse above
procedure.
NOTE: Freewheel control will automatically
disengage when the brake/clutch pedal is
depressed.TransmissionEngaged
Transmission Disengaged
NOTE: Toprotecthoodfrom damage when
transporting yourtractoron atruck oratrailer,
besure hood isclosed and securedtotractor.
Use an appropriate means of tying hood to
tractor (rope, cord, etc.).
TOWING CARTS AND OTHER A'rrACH-
MENTS
Tow only the attachments that are recom-
mended by and complywith specifications
of the manufacturer of your tractor, Use
common sense when towing. Tooheavy of
aload, whileonaslope, isdangerous.Tires
can losetractionwiththe ground and cause
you to lose controlofyour tractor.
13

BEFORE STARTING THE ENGINE
CHECK ENGINE OIL LEVEL
The engine in your tractor hasbeen shipped
from the factory already filled with summer
weight oil.
1. Check engine oil with tractor on level
ground.
2. Remove oil fill cap/dipstick and wipe
clean, reinsertthe dipstick and screw cap
tight, wait for a few seconds, remove and
read oil level, ffnecessary,, add oil until
"FULl" mark on dipstick is reached. Do
not overfill.
• For cold weather operation you should
change oil for easier starting (See the oil
viscosity chart inthe Maintenance section
of this manual).
• Tochange engine oil,seethe Maintenance
section in this manual.
ADD GASOLINE
• Fill fuel tank to bottom of filler neck. Do
not overfill.. Use fresh, clean, regular
gasoline with a minimum of 87 octane.
Do not mix oil with gasoline, Purchase
fuel in quantities that can be used within
0 days to ensure fuel freshness.
CAUTION: Wipe offany spilled oil orfuel.
Do not store, spill or use gasoline near an
open flame:
IMPORTANT: When operating intempera-
tures below 32°F (0°C), use fresh, clean
winter grade gasoline to help ensure good
cold weather starting,
CAUTION: Alcohol blended fuels (called
gasohol or using ethanol or methanol) can
attract moisture which leads to separation
andformation of acidsduring storage. Acidic
gas candamagethe fuel system ofanengine
while in storage, To avoid engine problems,
the fuel system should be emptied before
storage of 30 days or longer. Drain the gas
tank, start the engine and let it run until the
fuel lines and carburetor are empty. Use
fresh fuel nextseason. See Storage Instruc-
tions for additional information. Never use
engine or carburetor cleaner products in the
fuel tank or permanent damage may occur.
Fuelstabilizer isanacceptable alternative in
minimizingthe formation offuel gumdeposits
during storage. Add stabilizer to gasoline in
fuel tank or storage container. Always follow
the mix ratio found on stabilizer container.
Run engine at least 10 minutes after adding
stabilizer to allow the stabilizer to reach the
carburetor. Do not empty the gas tank and
carburetor if using fuel stabilizer.
TO START ENGINE
When starting the engine forthe first time or
if the engine has run out of fuel, it will take
extra cranking time to move fuel from the
tank to the engine.
1. Ensure freewheel control is in the trans-
mission engaged position,
2. Sitonseat inoperating position, depress
clutch!brake pedal and setparking brake.
3. Place motion control lever in neutral
position.
4. Move attachment clutch to disengaged
position.
5. Movethrottle control to choke position.
NOTE: Before starting, read the warm and
cold starting procedures below.
6. Insert key into ignition and turn key
clockwise to start position and release
key assoon as engine starts. Do not run
starter continuously for more than fifteen
seconds per minute, If the engine does
not start after several attempts, move
throttle control to fast position, wait a
few minutes and try again. Ifengine still
does not start, move the throttle control
back to the choke position and retry.
WARM WEATHER STARTING
(50°F (10°C) and above)
7. When engine starts, move the throttle
control to the fast position,
° The attachments and ground drive
can now be used. Ifthe engine does
not accept the load, restart the engine
and allow itto warm upfor one minute
using the choke as described above.
COLD WEATHER STARTING
(50°F (10°C) and below)
7. When engine starts, leavethrottle control
in choke position until engine warms up
and begins to run roughly. Once rough
running begins, immediately move the
throttle controltothe fast position. Engine
warm-up maytake from several seconds
to several minutes (the colder the tem-
perature, the longer the warm-up).
AUTOMATIC TRANSMISSION WARM UP
Before driving the unit in cold weather, the
transmission should be warmed up as fol-
lows:
1. Ensure the tractor is on level ground.
2. Place the motion control lever in neutral
Release the parking broke and let the
clutch/brake slowly return to operating
position.
14

3.AIIowoneminutefortransmissiontowarm
up.Thiscanbedoneduringtheengine
warmupperiod.
• Theattachmentscanalsobeuseddur-
ingtheenginewarm-upperiodafterthe
transmissionhasbeenwarmedup.
MOWING TIPS
• DO NOT use tire chains when the mower
housing is attached to tractor.
• Mower should be properly leveledfor best
mowing performance. See "TO LEVEL
MOWER HOUSING" in the Service and
Adjustments section of this manual.
• The left hand side of mower should be
used fortrimming.
• Drive sothat clippings aredischarged onto
the area that has already been cut. Have
the cutarea to the right ofthe tractor. This
will result in a more even distribution of
clippings and more uniform cutting.
• When mowing largeareas, start byturning
to the rightso that clippings will discharge
away from shrubs, fences, driveways,
etc. After one or two rounds, mow in the
opposite direction making left hand turns
until finished.
Z"
_ J
•If grass is extremely tall, it should be
mowed twice to reduce load and possible
fire hazard from dried clippings. Make
first cut relatively high; the second to the
desired height.
• Do not mow grass when it is wet. Wet
grass will plug mower and leave undesir-
able clumps. Allow grass to dry before
mowing.
• Always operate engine at full throttle
when mowing to assure better mow-
ing performance and proper discharge
of material. Regulate ground speed by
selecting a low enough gear to give the
mower cutting performance aswell asthe
quality of cut desired.
o When operating attachments, select a
ground speed that will suit the terrain and
give best performance of the attachment
being used.
15

MAINTENANCE eEFOnE
SCHEDULE _c.
USE
ull i i
Check Brake Op,erafien
Check Tire Pressure ......... V'
TCheck Operator Presence & ROS Systems I_'
A Check for Loose Fasteners
CCheeWReplace Mower Blades ......
T Lubrication Chart
0 Check 8attery Level
R Clean Battery and Terminals .........................
CleanDebrisO!.!...st_r!ngPla_
.Check Mower Levelness ..............
Check V-Belts ,lll,l,UHIII,Ul
Check Engine eli Level .If
Change Engin # Oil Imodels with oil filter)
Chan£te.Engtne Oil Imodels without oil filter)
_Clean Air Filt,itr ...............
G risenAl_Screen
IInspect _luffl_r/Spark Attester .
N Re place Oil Filter (If equipped ) ........
E,,C!eacEngine Cooling Fins
Replace Spark Plug .............
Replace Air Filter Paper Cartridge
.. R.eplace Fuel Filter ..................................
EVE_ EV_aV _SaY '&_;
8 25 _O 100
_OURS HOSES SOURS SOURS
v
i,,"
EVERY BEFORE
S_.ASON STOOGE
nl v,
V's
V' V'
v' v"
v'
v',
V_
GENERAL RECOMMENDATIONS
The warranty on this tractor does not cover
items that have been subjected to operator
abuse or negligence, To receive full value
from the warranty, operator must maintain
tractor as instructedin this manual.
Some adjustments will need to be made
periodically to properly maintain yourtractor.
At least once a season, chebk to see if
you should make any of the ,adjustments
described in the Service and iAdjustments
section of this manual.
* At least once a year you should replace
the spark plug, clean or replace air filter,
and check blades and belts for wear. A
new spark plug and clean air filter assure
proper air-fuel mixture and help your en-
gine run better and lastlonger.
BEFORE EACH USE
1. Check engine oil level.
2. Check brake operation.
3, Checktire pressure,
4. Check!pperator presence and
ROS sy'stems for proper operation,
5. Check for loosefasteners.
LUBRICATION CHART
Spindle---_ F----'--ql_ _ Spindle
Zerk _'_. __._,:_:_Zerk
//]__J_;_"%--L --f 'ij"-(_ Front
l_FrontWheel r_ _5:'_ Wheel
Steering[ _ /@ Enaine
SectorGear_ -,_L:_z:_L-'_',/
Teeth _!_,! i!_._![_
(_General Purpose Grease
@Referto Maintenance "ENGINE" Section.
IMPORTANT: Do not oil or grease the pivot
points which have special nylon bearings.
Viscous lubricants will attract dust and dirt
thatwUl shorten the life ofthe self-lubricating
bearings. Ifyoufeel they must belubricated,
use only a dry, powdered graphite type
lubricant sparingly.
16

TRACTOR
Always observe safety rules when perform-
ing any maintenance.
BRAKE OPERATION
if tractor requiresmorethan 5 feet (1,5 m)
to stop at highest speed inhighest gear on
a level, dry concrete or paved surface, then
brake must be serviced. _See"TO CHECK
BRAKE" in the Service and Adjustments
section of this manual).
TIRES
•Maintain proper air pressure in all tires
(See the side of tires for proper PSL)
o Keep tires free of gasoline, oil, or insect
control chemicals which can harm rubber.
•Avoid stumps, stones, deep ruts, sharp
objects andother hazards that may cause
tire damage.
NOTE: To seal tire punctures and prevent
fiat tires due to slow leaks, tire sealant may
be purchased from your local parts dealer.
Tire sealant also prevents tire dry rot and
corrosion.
OPERATOR PRESENCE SYSTEM AND
REVERSE OPERATION SYSTEM (ROS)
Be sure operator presence and reverse
operation systems are workingproperly. If
your tractor does not function as described,
repair the problem immediately.
•The engine should not start unless the
brake pedal is fully depressed, and the
attachment clutch control is in the disen-
gaged position.
CHECK OPERATOR PRESENCE SYSTEM
•When the engine is running, any attempt
by the operator to leavethe seat without
first settingthe parking brake should shut
off the engine.
- When the engine is running and the at-
tachment clutch is engaged, any attempt
by the operator to leave the seat should
shutoff the engine.
•The attachment clutch should never oper-
ate unless the operator is in the seat.
CHECK REVERSE OPERATION (ROS)
SYSTEM
• When the engineisrunning withthe ignition
switch in the engine"ON" position and the
attachment clutch engaged, anyattempt
bythe operator to drive in reverse should
shut off the engine,
•When the engineisrunningwiththe ignition
switch in the ROS "ON" position and the
attachment clutch engaged, any attempt
bythe operator to drive in reverse should
NOT shut off the engine.
Ros "On" Engine "On" Position
Position (Normal Operating)
BLADE CARE
Forbest resultsmower blades must besharp.
Replace worn, bent or damaged blades.
_IbCAUTION: Use onlya replacement blade
approvedbythe manufacturer ofyourtractor.
Using a blade not approved by the manu-
facturer of your tractor is hazardous, could
damage your tractor and void your warranty.
BLADE REMOVAL
1. Raise mower to highest position to allow
access to blades.
NOTE: Protect your hands with gloves and/
or wrap blade with heavy cloth,
2. Remove blade bolt by turningcounter-
clockwise.
3. Install new blade with stamped "GRASS
SIDE" facing the ground.
IMPORTANT: To ensure proper assembly,
center hole in blade must align with star on
mandrel assembly.
4. Install and tighten blade bolt securely
(45-55 Ft. Lbs./62-75 Nm).
IMPORTANT: Special blade bolt is heat
treated.
Star
Canter Hole
BATTERY
Your tractor has a battery charging system
which issufficient fornormal use. However,
periodic charging of the battery with an au-
tomotivecharger willextend its life.
-Keep battery and terminals clean.
• Keep battery bolts tight.
• Keep small vent holes open.
• Recharge at 6-10 amperes for I hour.
NOTE: The original equipment battery on
your tractor is maintenance free, Do not
attempt to open or remove caps or covers.
Adding or checking level of electrolyte is
not necessary.
17

TO CLEAN BATTERY AND TERMINALS
Corrosion and dirt on the battei'y and termi-
nals can cause the battery to ,leak" power.
1, Remove terminal guard.
2. Disconnect BLACK battery cable first
then RED battery cable and remove
battery from tractor.
3, Rinse the battery with plain water and
dry.
4. Clean terminals and battery cable ends
with wire brush until bright.
5. Coat termihals with grease or petroleum
jelly.
6, Reinstallbattery (See "REPLACING
BATTERY" in the Service and Adjust-
ments !section of this manual).
TRANSAXLE MAINTENANCE
The transaxlewas sealed at the factory and
fluid maintenance is not required for the life
ofthe transaxle. Should the transaxle ever
leak or require servicing, contact your near-
est Sears or other qualified service center.
V-BELTS
Check V-beltsfor deterioration andwearafter
100hours ofoperation and replace if neces-
sary, The belts are not adjustable. Replace
belts if they begin to slip from wear.
ENGINE
LUBRICATION
Only use high quality detergent oil rated with
API service classification SG-SL. Selectthe
oil's SAE viscosity grade according to your
expected operating temperature.
NOTE: Although multi-viscosity oils (5W30,
10W30 etc,)improve starting incoldweather,
they will result in increased oil consumption
whenusedabove32°F/0°C.Checkyourengine
oil level more frequently to avoid possible
engine damage from running low on oil.
Change the ,oil after every 50 hours of
operation orat..least once ayear ifthe tractor
isnot used fo_50 hours inone year,
Checkthe crarikcase oillevel before starting
the engine .and after each eight (8) hours
of operation. Tighten oil fill cap/dipstick
securely each time you check the oil level.
TO CHANGE ENGINE OIL
Determine temperature range expected
before oil change. All oil must meet AP[
service classification SG-SL
•Ensure tractor is on level surface.
• Oil will drain more freely when warm,
•Catch oil in a suitable container.
LOWER DASH COVER REMOVAL
1. Raise hood.
2. Remove fastener from lower dash cover,
CAUTION: Remove lower dash cover care-
fully to ensure cover tabs are not broken.
3. Slide lower dash cover up to release
cover tabs from tapered slots in lower
dash and remove.
LowerDash
4. Remove oil fill cap/dipstick. Be careful
nottoallow dirt to enter the engine when
changing oil.
5. RemoveyeUowcapfromendofdrainvalve
and install the drain tube ontothe fitting.
OilDrainValve
Tube
6. Unlock drain vafve by pushing inward
and turning counterclockwise.
7, To open, putl out on the drainvalve.
8. After oilhasdrained completely,closeand
tock the drain valve by pushing inward
and turning clockwise until the pin is in
the locked position as shown,
9, Removethedraintubeand replacethecap
ontoto the bottom fitting ofthe drainvalve.
10, Refilfengine with oilthrough oilfilldipstick
tube. Pour slowly. Do not overfill, For
approximate capacity see "PRODUCT
SPECIFICATIONS"sectIonofthismanual,
18

11.Use gauge on oil fill cap/dipstick for
checking level. Insert dipstick into the
tube and rest the oil fill cap on the tube.
Do notthread the capontothe tube when
taking reading. Keep oil at "FULL' line
on dipstick. Tighten cap onto the tube
securely when finished.
ENGINE OIL FILTER
Replace the engine oil filter every season or
every other oil change if the tractor is used
more than 100 hours in one year.
NOTE: If needed, remove lower dashcovers
using stepsfrom"Lowerdash coverremoval"
section of this manual.
AIR FILTER
Your engine will not run properly using a
dirty airfilter. Service paper cartridge every
100 hours of operation or every season,
whichever occurs first.
Service air cleaner more often under dusty
conditions.
NOTE: If needed, remove lower dash covers
using steps from "Left Lower Dash Cover
Removal" section of this manual.
1. Remove cover,
2, Carefully remove a_irfilter cartridge and
pre-cleaner from base.
3. Clean base carefully to prevent debris
from falling into carburetor.
NOTE: If very dirty or damaged, replace
cartridge.
4. Place new pre-cleaner and cartridge
firmly in base.
5. Replace cover.
IMPORTANT: Petroleum solvents, such as
kerosene, are not to be used to clean the
cartridge. They may cause deterioration of
the cartridge. Do not oil cartridge, Do not
use pressurized air to clean cartridge.
CLEAN AIR SCREEN
The air screen is over the air intake blower
located on top of engine. The air screen
must be kept free ofdirt and chaffto prevent
engine damagefrom overheating. Cleanwith
a wire brush or compressed air to remove
dirt and stubborn dried gum fibers.
ENGINE COOLING SYSTEM
Debris may clog the engine's air cooling
system. Remove blower housing and clean
area shown to prevent overheating and
engine damage.
AirScree Cleanout chaff
r_.\ anddebris
IN-LINE FUEL FILTER
The fuel filter should be replaced onceeach
season. Iffuel filter becomes clogged, ob-
structing fuelflowto carburetor, replacement
is required.
I. With engine cool, remove filter and plug
fuel line sections.
2, Place newfuel filter in position infuel line
with arrow pointing towards carburetor,
3. Be sure there are nofuel line leaks and
clamps are properly positioned,
4. Immediatelywipe upanyspilledgasoline.
Clamp
FuelFilter__.__j/
MUFFLER
Inspect and replace corroded muffler and
spark arrester (ifequipped) asit could create
a fire hazard and/or damage.
SPARK PLUG(S)
Repl.acesparkplug(s)atthebeginningofeach
mowing season or after every 100 hours of
operation, whichever occursfirst. Sparkplug
typeand gapsetting areshown in"PRODUCT
SPECIFICATIONS" section of this manual.
19

CLEANING
• Clean engine, battery, seat, finish, etc.
of all foreign matter.
• Clean debris from steering plate. Debris
canrestrictclutch/brakepeda.lshaftmove-
ment, causing belt slip and toss of drive.
S
ACAUTION: Avoid all pinch points and
movable parts
Clutch/brakepedal
top
4, Pull back the lock collar of the nozzle
adapter and push the adapter onto the
deck washout port at the left end ofthe
mower deck. Release the lock collar to
lock the adapter on the nozzle.
Washout Port
Steering
SteeringSystem,Dash,Fender
andMowerNotShown
° Keep finished surfaces and wheels free
of all gasoline, oil, etc.
• Protectpainted surfaces with automotive
type wax.
Except fQr the washout port (if equipped),
we do not recommend using agarden hose
or pressure washer to clean the outside of
your tractor unless the engine and transmis-
sion are covered to keep water out. Water
in engine or transmission will shorten the
useful life of your tractor. Use compressed
air or aleaf blower to remove grass, leaves
and trash from outside tractor and mower.
DECK WASHOUT PORT
Your tractor's deck is equipped with a
washout port on its surface as part of its
deck wash system. It should be utilized af-
ter each use.
1, Drive the tractor to a level, clear spot
on your lawn, near enough to a water
spigot for your garden hose to reach.
IMPORTANT: Make certain the tractor's
discharge chute is directed AWAYfrom your
house, garage, parked cars, etc. Remove
bagger chute or mulch cover if attached.
2. Makesurethe attachment_clutchcontrol
is in the "DISENGAGED" position, set
the parking brake, andstop the engine.
3. Thread the nozzle adapter (packaged
with your tractor's Operator's Manual)
onto the end of your garden hose.
>i
IMPORTANT: Tug hose ensuring connec-
tion is secure.
5. Turnthe water on,
6. While sitting in the operator's position
on the tractor, re-start the engine and
place the throttle lever in the Fast ",t_"
position.
IMPORTANT: Recheck the area making
cerbainthe area is clear.
7. Move the tractor's attachment clutch
control to the "ENGAGED" position.
Remain in the operator's position
with the cutting deck engaged until the
deck is cleaned.
8. Move the tractor's attachment clutch
control to the "DISENGAGED" posi-
tion. Turnthe ignition keyto the STOP
position toturn the tractor's engine off.
Turnthe water off,
9, Pull back the lock collar of the nozzle
adapter to disconnec_the adapter from
the nozzle washout port.
10. Move the tractor to a dry area, prefer-
ably a concrete or paved area. Place
the attachment clutch control in the
"ENGAGED" positionto removeexcess
water andto help dry before putting the
tractor away.
AI_WARNING: Abrokenormissingwashout
fittingcould exposeyouor otherstothrown
objectsfromcontactwiththeblade,
Replacebrokenor missingwashoutfitting
immediately,priorto usingmoweragain,
Plug any holes in mowerwith bolts and
Iocknuts,
20