Craftsman 917.378352 User manual

Owner's Manual
iCRnFTSMRN'i
ROTARY LAWN MOWER
6.25 Horsepower
Power-Propelled
21" Rear Discharge
Model No.
917.378352
CAUTION:
Read and followall
Safety Rules and Instructions
beforeoperatingthis equipment
Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.
Visit ourCraftsman website:www.sears.com/craftsman

Warranty ............................................... 2
Safety Rules ...................................... 2-4
Assembly /Pre-Operation .................... 5
Operation ........................................... 6-9
Maintenance Schedule ...................... 10
Maintenance ................................. 10-13
Product Specifications ........................ 11
Service and Adjustments .............. 13-14
Storage ......................................... 15-16
Troubleshooting ........................... 16-17
Repair Parts .................................. 34-43
Sears Service ...................... Back Cover
LIMITED TWO YEAR WARRANTY ON CRAFTSMAN POWER MOWER
For two years from date of purchase, when this Craftsman Lawn Mower is maintained,
lubricated, and tuned up according to the operating and maintenance instructions in
the owner's manual, Sears will repair free of charge any defect in material or workman-
ship.
If this Craftsman Lawn Mower is used for commercial or rental purposes, this warranty
applies for only 90 days from the date of purchase.
This Warranty does not cover:
• Expendable items which become worn during normal use, such as rotary mower
blades, blade adapters, belts, air cleaners and spark plug.
• Repairs necessary because of operator abuse or negligence, including bent
crankshafts and the failure to maintain the equipment according to the instructions
contained in the owner's manual.
Warranty service is available by returning the Craftsman power mower to the nearest
Sears Service Center/Department in the United States. This warranty applies only
while this product is used in the United States.
This Warranty gives you specific legal rights, and you may also have other rights which
vary from state to state.
Sears, Roebuck and Co., D/817 WA, Hoffman Estates, Illinois 60179
IMPORTANT: This cutting machine is capable of amputating hands and feet and
throwing objects. Failure to observe the following safety instructions could result in
serious injury or death.
_Look for this symbol to point out
important safety precautions. It means
CAUTIONt!] BECOMEALERTt!! YOUR
SAFETY IS INVOLVED.
ACAUTION: Always disconnect spark
plug wire and place wire where it cannot
contact spark plug in order to prevent
accidental starting when setting up,
transporting, adjusting or making repairs.
AWARNING: Battery posts, terminals and
related accessories contain lead and
lead compounds, chemicals known to the
State of California to cause cancer and
birth defects or other reproductive harm.
Wash hands after handling.
A, WARNING: Engine exhaust, some of
its constituents, and certain vehicle
components contain or emit chemicals
known to the State of California to cause
cancer and birth defects or other repro-
ductive harm. 2
• l, CAUTION: Muffler and other engine
parts become extremely hot during
operation and remain hot after engine
has stopped. To avoid severe bums on
contact, stay away from these areas.

I,GENERAL OPERATION
• Read, understand, and follow all
instructions on the machine and in the
manual(s) before starting. Be thor-
oughly familiar with the controls and
the proper use of the machine before
starting.
• Do not put hands or feet near or under
rotating parts. Keep clear of the
discharge opening at all times.
•Only allow responsible individuals,
who are familiar with the instructions, to
operate the machine.
• Clear the area of objects such as
rocks, toys, wire, bones, sticks, etc.,
which could be picked up and thrown
by the blade.
• Be sure the area is clear of other
people before mowing. Stop machine if
anyone enters the area.
• Do not operate the mower when
barefoot or wearing open sandals.
Always wear substantial foot wear.
• Do not pull mower backwards unless
absolutely necessary. Always look
down and behind before and while
moving backwards.
• Do not operate the mower without
proper guards, plates, grass catcher or
other safety protective devices in place.
• See manufacturer's instructions for
proper operation and installation of
accessories. Only use accessories
approved by the manufacturer.
• Stop the blade(s) when crossing gravel
drives, walks, or roads.
• Stop the engine (motor) whenever you
leave the equipment, before cleaning
the mower or unclogging the chute.
• Shut the engine (motor) off and wait
until the blade comes to complete stop
before removing grass catcher.
• Mow only in daylight or good artificial
light.
• Do not operate the machine while
under the influence of alcohol or drugs.
• Never operate machine in wet grass.
Always be sure of your footing: keep a
firm hold on the handle and walk;
never run.
• Disengage the self-propelled mecha-
nism or drive clutch on mowers so
equipped before starting the engine
(motor).
• If the equipment should start to vibrate
abnormally, stop the engine (motor)
and check immediately for the cause.
Vibration is generally a warning of
trouble.
• Always wear safety goggles or safety
glasses with side shields when
operating mower.
U, SLOPE OPERATION
Slopes are a major factor related to slip
and fall accidents which can result in
severe injury. All slopes require extra
caution. If you feel uneasy on a slope, do
not mow it.
DO:
• Mow across the face of slopes: never
up and down. Exercise extreme caution
when changing direction on slopes.
•Remove obstacles such as rocks, tree
limbs, etc.
• Watch for holes, ruts, or bumps. Tall
grass can hide obstacles.
DO NOT:
• Do not trim near drop-offs, ditches or
embankments. The operator could lose
footing or balance.
• Do not trim excessively steep slopes.
•Do not mow on wet grass. Reduced
footing could cause slipping.
II1.CHILDREN
Tragic accidents can occur if the operator
is not alert to the presence of children.
Children are often attracted to the
machine and the mowing activity. Never
assume that children will remain where
you last saw them.
• Keep children out of the tdmming area
and under the watchful care of another
responsible adult.
• Be alert and turn machine off if children
enter the area.
• Before and while walking backwards,
look behind and down for small
children.
• Never allow children to operate the
machine.
• Use extra care when approaching blind
comers, shrubs, trees, or other objects
that may obscure vision.
IV, SERVICE
•Use extra care in handling gasoline
and other fuels. They are flammable
and vapors are explosive.
-Use only an approved container.
-Never remove gas cap or add fuel
with the engine running. Allow
engine to cool before refueling. Do
not smoke.
-Never refuel the machine indoors.
- Never store the machine or fuel
container inside where there is an
open flame, such as a water heater.
3

• Never run a machine inside a closed
area.
• Never make adjustments or repairs
with the engine (motor) running.
Disconnect the spark plug wire, and
keep the wire away from the plug to
prevent accidental starting.
• Keep nuts and bolts, especially blade
attachment bolts, tight and keep
equipment in good condition.
•Never tamper with safety devices.
Check their proper operation regularly.
• Keep machine free of grass, leaves, or
other debris build-up. Clean oil or fue!
spillage. Allow machine to cool before
storing.
• Stop and inspect the equipment if you
strike an object. Repair, if necessary,
before restarting.
• Never attempt to make wheel height
adjustments while the engine (motor) is
running.
• Grass catcher components are subject
to wear, damage, and deterioration,
which could expose moving parts or
allow objects to be thrown. Frequently
check components and replace with
manufacturer's recommended parts,
when necessary.
° Mower blades are sharp and can cut.
Wrap the blade(s) or wear gloves, and
use extra caution when servicing them.
• Do not change the engine governor
setting or overspeed the engine.
These accessories were available when this lawn mower was produced. They are not
shipped with your mower. They are also availableat mostSearsretail outlets andservice
centers. Most Sears stores can alsoorder repairpartsfor you, when youprovidethe model
numberofyour lawnmower. Some of these accessoriesmay notapplytoyourlawn mower.
LAWN MOWER PERFORMANCE
CLIPPING
DEFLECTORS
FOR
REAR DISCHARGE
LAWN MOWERS
GRASS CATCHERS
FOR
REARDISCHARGE
LAWN MOWERS
STABILIZER GAS
CANS
GRASSCATCHERS
FOR
SIDEDISCHARGE
LAWNMOWERS
LAWN MOWER MAINTENANCE
MUFFLERS
BELTS BLADES
AIR RLTERS
BL_DE ADAPTERS iWHEELS
SPARK PLUGS
ENGINE OIL
4

Read these instructions and this manual
in its entirety before you attempt to
assemble or operate your new lawn
mower.
IMPORTANT: This lawn mower is
shipped WITHOUT OIL OR GASOLINE in
the engine.
Your new lawn mower has been as-
sembled at the factory with the exception
of those parts left unassembled for
shipping purposes. All parts such as nuts,
washers, bolts, etc., necessary to com-
plete the assembly have been placed in
the parts bag. To ensure safe and proper
operation of your lawn mower, all parts
and hardware you assemble must be
tightened securely. Use the correct tools
as necessary to ensure proper tightness.
TO REMOVE LAWN MOWER FROM
CARTON
1. Remove loose parts included with
mower.
2. Cut down two end corners of carton
and lay end panel down flat.
3. Remove all packing materials except
padding between upper and lower
handle and padding holding operator
presence control bar to upper handle.
4. Roll lawn mower out of carton and
check carton thorougly for additional
loose pads.
HOW TO SET UP YOUR LAWN
MOWER
TO UNFOLD HANDLE
IMPORTANT: Unfold handle carefully so
as not to pinch or damage control cables.
1. Raise handles until lower handle
section locks into place in mowing
position.
2. Remove protective padding, raise
upper handle section into place on
lower handle and tighten both handle
knobs.
3. Remove handle padding holding
operator presence control bar to
upper handle.
Your lawn mower handle can be adjusted
for your mowing comfort. Refer to "AD-
JUST HANDLE" in the Service and
Adjustments section of this manual.
Operator
control bar
LIFT
UF
Mowing
position
Lower handle
TO ASSEMBLE GRASS CATCHER
1. Put grass catcher frame into grass bag
with rigid part of bag on the bottom.
Make sure the frame handle is outside
of the bag top.
2. Slip vinyl bindings over frame.
NOTE: If vinyl bindings are too stiff, hold
them in warm water for a few minutes. If
bag gets wet, let it dry before using.
Catcher
frame
handle
Frame
opening
TO INSTALL ATTACHMENTS
Your lawn mower was shipped ready to
be used as a mulcher. To convert to
bagging, see "TO CONVERT MOWER" in
the Operation section of this manual).
5

KNOW YOUR LAWN MOWER
READ THIS OWNER'S MANUAL AND ALL SAFETY RULES BEFORE OPERATING
YOUR LAWN MOWER. Compare the illustrations with your lawn mower to familiarize
yourself with the location of various controls and adjustments. Save this manual for
future reference.
These symbols may appear on your lawn mower or In literature supplied with the
product. Learn and understand their meaning.
CAUTION ENGINE ENGINE FAST SLOW CHOKE FUEL OIL DANQER, KEEP HANDS
OR WARNING ON OFF AND FEET AWAY
Operator presence control bar
• Drive control lever
knob
Grass catcher Air filter
Engine oil cap
with dipstick
cover
Housing Wheel adjuster (on each wheel)
IMPORTANT: This lawn mower is shipped WITHOUT OIL OR GASOLINE in the engine.
MEETS CPSC SAFETY REQUIREMENTS
Sears rotary walk-behind power lawn mowers conform to the safety standards of the
American National Standards Institute and the U.S. Consumer Product Safety Commis-
sion. The blade turns when the engine is running.
Operator presence control bar -must
be held down to the handle to start the
engine. Release to stop the engine,
Primer -pumps additional fuel from the
carburetor to the cylinder for use when
starting a cold engine. 6
Starter handle -used for starting the
engine.
Drive control lever -used to engage
power-propelled forward motion of lawn
mower.

The operation of any lawn
mower can result in foreign
objects thrown into the
eyes, which can result in
severe eye damage.
Always wear safety glasses or eye
shields while operating your lawn mower
or performing any adjustments or repairs.
We recommend standard safety glasses
or a wide vision safety mask worn over
spectacles.
HOWTO USE YOUR LAWN MOWER
ENGINE SPEED
The engine speed was set at the factory
for optimum performance, Speed is not
adjustable.
ENGINE ZONE CONTROL
• I,CAUTION: Federal regulations require
an engine control to be installed on this
lawn mower in order to minimize the risk
of blade contact injury. Do not under any
circumstances attempt to defeat the
function of the operator control. The blade
turns when the engine is running.
•Your lawn mower is equipped with an
operator presence control bar which
requires the operator to be positioned
behind the lawn mower handle to start
and operate the lawn mower,
DRIVE CONTROL
• Self-propelling is controlled by holding
the operator presence control bar down
to the handle and pushing the drive
control lever forward until it clicks; then
releasing the lever.
•Forward motion will stop when the
operator presence control bar is
released. To stop forward motion
without stopping engine, release the
operator presence control bar slightly
until the drive control disengages. Hold
operator presence control bar down
against handle to continue mowing
without self-propelling.
•To keep drive control engaged when
turning comers, push down on handle
and lift front wheels off ground while
turning lawn mower.
Operator presence control bar Drive
\ =\\ _ ",..2,,_ control
\\\ DRIVE CONTROL DISENGAGED
TO ADJUST CUTTING HEIGHT
Raise wheels for low cut and lower
wheels for high cut, adjust cutting height
to suit your requirements. Medium
position is best for most lawns.
•To change cutting height, squeeze
adjuster lever toward wheel. Move
wheel up or down to suit your require-
ments. Be sure all wheels are in the
same setting.
NOTE: Adjuster is properly positioned
when plate tab inserts into hole in lever.
Also, 9-position adjusters (if so equipped)
allow lever to be positioned between the
plate tabs.
LOWER WHEELS FOR HIGH CUT
_ Plate tab_O_P
--4" 'W_" t_*
RAISE WHEELS FOR LOW CUT Lever
TO CONVERT MOWER
Yourlawnmower was shipped readyto be
usedas a mulcher. Toconverttobagging:
• Lift rear door of the lawn mower and place
the grass catcher frame hooks onto the
door pivot pins.
•To convert to mulching operation, remove
grass catcher and close rear door.
_,CAUTION: Do not run your lawn mower
without rear door closed, clipping
deflector or approved grass catcher in
place. Never attempt to operate the lawn
mower with the rear door removed or
propped open.
Pivot Rear Grass
catcher
handle
Catcher frame
7

TO EMPTY GRASS CATCHER
1. Lift up on grass catcher using the
frame handle,
2. Remove grass catcher with clippings
from under lawn mower handle.
3. Empty clippings from bag using both
frame handle and bag handle.
NOTE: Do not drag the bag when
emptying; it will cause unnecessary wear.
Grass
catcher
frame
handle
Bag
handle
_!_CAUTION: Wipe off any spilled oil or
fuel. Do not store, spill or use gasoline
near an open flame.
_i, CAUTION: Alcohol blended fuels (called
gasohol or using ethanol or methanol) can
attract moisture which leads to separation
and formation of acids dudng storage. Acidic
gas can damage the fuel system of an en-
gine while in storage. To avoid engine
problems, the fuel system should be emp-
tied before storage of 30 days or longer.
Drain the gas tank, start the engine and let
it run until the fuel lines and carburetor are
empty. Use fresh fuel next season. See
Storage Instructions for additional informa-
tion. Never use engine orcarburetor cleaner
products in the fuel tank or permanent dam-
age may occur.
Engine Gasoline
oil cap filler cap
BEFORE STARTING ENGINE
ADD OIL
Your lawnmower is shipped without oil in
the engine. For type and grade of oil to
use, see "ENGINE" in the Maintenance
section of this manual.
/IL CAUTION: DO NOT overfill engine with
oil, or it will smoke on startup.
1. Be sure lawnmower is level and area
around oil fill is clean.
2. Remove oil dipstick from oil fill spout.
Make sure that rim of spout is clean.
3. You receive a container of oil with the
unit. Slowly pour the entire container
down the oil fill spout into the engine.
4. Wait one minute to allow oil to settle.
Insert and tighten dipstick, then
remove it to check oil level.
5. Always be sure to retighten oil dipstick
before starting engine.
•Check oil level before each use. Add
oil if needed. Fill to full line on dipstick.
• Change the oil after every 25 hours of
operation or each season. You may
need to change the oil more often
under dusty, dirty conditions.
ADD GASOLINE
•Fill fuel tank to bottom of tank filler
neck. Do not overfill. Use fresh, clean,
regular unleaded gasoline with a
minimum of 87 octane. Do not mix oil
with gasoline. Purchase fuel in
quantities that can be used within 30
days to assure fuel freshness.
TO START ENGINE
NOTE: Due to protective coatings on the
engine, a small amount of smoke may be
present during the initialuse of the product
and should be considered normal.
1. To start a cold engine, push primer
three (3) times before trying to start.
Use a firm push. This step is not
usually necessary when starting an
engine which has already run for a
few minutes.
2. Hold operator presence control bar
down to the handle and pull starter
handle quickly. Do not allow starter
rope to snap back.
TO STOP ENGINE
•To stop engine, release operator
presence control bar.
NOTE: In cooler weather itmay be
necessary to repeat pdming steps. In
warmer weather over priming may cause
flooding and engine will not start. If you
do flood engine, wait a few minutes
before attempting te start and do not
repeat priming steps.
8

MOWING TIPS
• Under certain conditions, such as very
tall grass, it may be necessary to raise
the height of cut to reduce pushing
effort and to keep from overloading the
engine and leaving clumps of grass
clippings. It may also be necessary to
reduce ground speed and/or run the
mower over the area a second time.
• For extremely heavy cutting, reduce the
width of cut by overlapping previously
cut path and mow slowly.
• For better grass bagging and most
cutting conditions, the engine speed
should be set in the FAST position.
• When using a rear discharge lawn
mower in moist, heavy grass, clumps of
cut grass may not enter the grass
catcher. Reduce ground speed
(pushing speed) and/or run the lawn
mower over the area a second time.
•If a trail of clippings is left on the right
side of a rear discharge mower, mow in
a clockwise direction with a small
overlap to collect the clippings on the
next pass.
• Pores in cloth grass catchers can
become filled with dirt and dust with
use and catchers will collect less grass.
To prevent this, regularly hose catcher
off with water and let dry before using.
• Keep top of engine around starter clear
and clean of grass clippings and chaff.
This will help engine air flow and
extend engine life.
MULCHING MOWING TIPS
IMPORTANT: For best performance,
keep mower housing free of built-up
grass and trash. See "CLEANING" in the
Maintenance section of this manual.
•The special mulching blade will recur
the grass clippings many times and
reduce them in size so that as they fall
onto the lawn they will disperse into the
grass and not be noticed. Also, the
mulched grass will biodegrade quickly
to provide nutrients for the lawn.
Always mulch with your highest engine
(blade) speed as this will provide the
best recutting action of the blades.
•Avoid cutting your lawn when it is wet.
Wet grass tends to form clumps and
interferes with the mulching action. The
best time to mow your lawn is the early
afternoon. At this time the grass has
dried and the newly cut area will not be
exposed to the direct sun.
•For best results, adjust the lawn mower
cutting height so that the lawn mower
cuts off only the top one-third ofthe
grass blades. If the lawn is overgrown it
will be necessary to raise the height of
cut to reduce pushing effort and to keep
from overloading the engine and
leaving clumps of mulched grass. For
extremely heavy grass, reduce your
width of cut by overlapping previously
cut path and mow slowly.
_MAX 1/3
•Certain types of grass and grass
conditions may require that an area be
mulched a second time to completely
hide the clippings. When doing a
second cut, mow across or perpendicu-
lar to the first cut path.
•Change your cutting pattern from week
to week. Mow north to south one week
then change to east to west the next
week. This will help prevent matting
and graining of the lawn.
9

MAINTENANCE SCHEDULE/___o_y
YOUCOMP,
.Eeu .sE.v,o DATES
/I I i/i/-
Check forLooseFasteners _ if
Clean/InspectGrassCatoher
(IfEquipped) f/ _
M Clean Lawn Mower
O Clean Under Drive Cover
(Power-Propelled Mowers)
Check drive deWp_Jlleys
RE(Power-Propelled Mowers} I#/
Check/Shmpan/Raplace Blade _#
Lubd_tlon Chart
Clean Sattew/Recharge
IElectdc Start Mowers_ I_
ECheck Engine011Level ¥/
NChange EngineOil */1_
G Ck.u__r niter II/=
I InspectMuffler _'
Clean or Replace Spark Plug v'
NReplaceAirniter PaperCartridge I_=
q/
,/4
1. ChangemoreoRenwhenopera,rigunderahem_yloadorInhigh_tmzzpermur-,,=.
2. Se_k_emoreo/tenwhenoper_ng In dldyordu_y _,nditlons.
3. ReplaceI_du moreof_n whimrnowlngInsandy Imll.
4. Cl,,azge48 houriat endof =euon.
GENERAL RECOMMENDATIONS
The warranty on this lawn mower does
not cover items that have been subjected
to operator abuse or negligence. To
receive full value from the warranty,
operator must maintain mower as
instructed in this manual.
Some adjustments will need to be made
periodically to properly maintain your
unit.
All adjustments in the Service and
Adjustments section of this manual
should be checked at least once each
season.
•Once a year, replace the spark plug,
clean or replace air filter element and
check blade for wear. A new spark
plug and clean/new air filter element
assure proper air-fuel mixture and help
your engine run better and last longer.
• Follow the maintenance schedule in
this manual.
LUBRICATION CHART
(_) Wheel adjuster
3n each wheel)
I((DBra.e
j\...__ springbracket
Rear
(_) Handle bracket mounting pins door hinge
(_ Spray lubricant
BEFORE EACH USE
1. Check engine oil level,
2. Check for loose fasteners.
LUBRICATION
Keep unit well lubricated (See =LUBRI-
CATION CHART"). 10
_) See "ENGINE" In Maintenance section.
IMPORTANT: Do not oil or grease
plastic wheel bearings. Viscous
lubricants will attract dust and dirt that
will shorten the life of the self-lubricat-
ing bearings. If you feel they must be
lubricated, use only a dry, powdered
graphite type lubricant sparingly.

PRODUCT SPECIFICATIONS
Serial Number:
Date of Purchase:
Gasoline Capacity /Type: 1.5 Quarts (Unleaded Regular)
Oil Type (API-SF-SJ): SAE 30 (above 32°F); SAE 5W-30 (below 32°F)
Oil Capacity: 20 Ounces
Spark Plug (Gap: .030") Champion RJ19LM or J19LM
Blade Bolt Torque: 35-40 ft. Ibs.
The model and serial numbers will be found on a decal on the rear of the mower
housing. Record both serial number and date of purchase in space provided above
LAWN MOWER
Always observe safety rules when perform-
ing any maintenance.
TIRES
•Keep tires free of gasoline, oil, or insect
control chemicals which can harm rubber.
• Avoid stumps, stones, deep ruts, sharp
objects and other hazards that may cause
tire damage.
BLADE CARE
For best results, mower blade must be
kept sharp. Replace bent or damaged
blades.
TO REMOVE BLADE
1. Disconnect spark plug wire from spark
plug and place wire where it cannot
come in contact with spark plug.
2. Turn lawn mower on its side. Make
sure air filter and carburetor are up.
3. Use a wood block between blade and
mower housing to prevent blade from
turning when removing blade bolt.
NOTE: Protect your hands with gloves
and/or wrap blade with heavy cloth.
4. Remove blade bolt by turning counter-
clockwise.
5. Remove blade and attaching hard-
ware (bolt, lock washer and hardened
washer).
NOTE: Remove the b_ade adapter and
check the key inside hub of blade
adapter. The key must be in good condi-
tion to work properly. Replace adapter if
damaged.
TO REPLACE BLADE
1. Position the blade adapter on the
engine crankshaft. Be sure key in
adapter and crankshaft keyway are
aligned.
2. Position blade on the blade adapter
aligning the two (2) holes in the blade
with the raised lugs on the adapter.
3. Be sure the trailing edge of blade
(opposite sharp edge) is up toward
the engine.
4. Install the blade bolt with the lock
washer and hardened washer into
blade adapter and crankshaft.
5. Use block of wood between blade and
lawn mower housing and tighten the
blade bolt, turning clockwise.
• The recommended tightening torque is
35-40 ft. Ibs.
IMPORTANT: Blade bolt is grade 8 heat
treated.
TO SHARPEN BLADE
NOTE: We do not recommend sharpen-
ing blade - but if you do, be sure the
blade is balanced.
Care should be taken to keep the blade
balanced. An unbalanced blade will
cause eventual damage to lawn mower
or engine.
•The blade can be sharpened w_th afile
or on a grinding wheel. Do not attempt
to sharpen while on the mower.
•To check blade balance, drive a nail
into a beam or wall. Leave about one
inch of the straight nail exposed. Place
center hole of blade over the head of
the nail. If blade is balanced, it should
remain in a horizontal position. If either
end of the blade moves downward,
sharpen the heavy end until the blade
is balanced.
Blade adapter _ Crankshaft
Key._/_,= 1 "_ keyway
Lockwasher [II'(-.,F_ /J._
_._. \ II _ i l-i \.'%_).J_:_JFtCrank
Blade \ _ _ _....._ _._v_/, __
bolt Hardene_ " ' ..._--/ .. ----
washer Trailing edge Blade adapter
11

GRASS CATCHER
•The grass catcher may be hosed with
water, but must be dry when used.
• Check your grass catcher often for
damage or deterioration. Through
normal use it will wear. If catcher needs
replacing, replace only with a manufac-
turer approved replacement catcher.
Give the lawn mower model number
when ordering.
DRIVE WHEELS
Check front drive wheels each time
before you mow to be sure they move
freely.
The wheels not turning freely means
trash, grass cuttings, etc. are in the drive
wheel area and must be cleaned to free
drive wheels.
If necessary to clean the drive wheels, be
sure to clean both front wheels.
1. Remove hubcaps, hairpin cotters and
washers.
2. Remove wheels from wheel adjusters.
3. Remove any trash or grass cuttings
from inside the dust cover, pinion and/
or drive wheel gear teeth.
4. Put wheels back in place.
NOTE: If after cleaning, the drive wheels
do not turn freely, contact a Sears or other
qualified service center.
GEAR CASE
• To keep your drive system working
properly, the gear case and area
around the drive should be kept clean
and free of trash build-up. Clean under
the drive cover twice a season.
•The gear case is filled with lubricant to
the proper level at the factory. The only
time the lubricant needs attention is if
service has been performed on the
gear case.
• If lubricant is required, use only Elf
brand oil, Pad No. REDUCTELF 100.
Do not substitute.
ENGINE
LUBRICATION
Use only high quality detergent oil rated
with API service classification SF-SJ.
Select the oil's SAE viscosity grade
according to your expected operating
temperature.
_RATURE RANGE ANTICIPATED _FORE NEXT OIL CHANGE
NOTE: Although multi-viscosity oils
(5W30, 10W30 etc.) improve starting in
cold weather, these multi-viscosity oils
will result in increased oil consumption
when used above 32°F. Check your
engine oil level more frequently to avoid
possible engine damage from running
low on oil.
Change the oil after every 25 hours of
operation or at least once a year if the
lawn mower is not used for 25 hours in
one year.
Check the crankcase oil level before start-
ing the engine and after each five (5) hours
of continuous use. Tighten oil plug securely
each time you check the oil level.
TO CHANGE ENGINE OIL
NOTE: Before tipping lawn mower to
drain oil, drain fuel tank by running
engine until fuel tank is empty.
1. Disconnect spark plug wire from spark
plug and place wire where it cannot
come in contact with spark plug.
2. Remove engine oil cap; lay aside on a
clean surface.
3. Tip lawn mower on its side as shown and
drain oil into a suitable container. Rock
lawn mower back and forth to remove
any oil trapped inside of engine.
4. Wipe off any spilled oil from lawn
mower or side of engine.
5. Fill engine with oil. The engine oil
capacity is 20 oz. If oil is not com-
pletely drained from engine, you may
not need the entire container of a 20
oz. bottle of oil. Slowly pour 3/4 of the
oil from the container down the oil fill
spout into the engine.
6. Wait one minute to allow oil to settle.
Insert and tighten dipstick, then
remove it to check oil level.
7. Continue adding small amounts of oil
and rechecking the dipstick until it
reads full. DO NOT overfill, or engine
will smoke on startup.
8. Always be sure to retighten oil dipstick
before starting engine.
9. Reconnect spark plug wire to spark plug.
12 Container

AIR FILTER
Your engine will not run properly and may
be damaged by using a dirty air filter,
Replace the air filter every 100 hours of
operation or every season, whichever
occurs first. Service air cleaner more
often under dusty conditions, Do not
wash air filter.
TO CHANGE AIR FILTER
1. Remove the air filter by turning
counterclockwise to the stop and pull
away from collar.
2. Remove filter from inside of cover.
3. Clean the inside of the cover and the
collar to remove any dirt accumula-
tion.
4. Insert new filter into cover.
5. Put air filter cover and filter into collar
aligning the tab with the slot,
6. Push in on cover and turn clockwise to
tighten.
Collar TURN
COUNTER-
CLOCK-
WISE
TO
RE-
MOVE
Slot
Air filter' TURN
CLOCK-
WISE TO TIGHTEN
MUFFLER
Inspect and replace corroded muffler as it
could create a fire hazard and/or damage.
SPARK PLUG
Replace spark plug at the beginning of
each mowing season or after every 100
hours of operation, whichever occurs first.
Spark plug type and gap setting are
shown in "PRODUCT SPECIFICATIONS"
in Maintenance section of this manual,
CLEANING
IMPORTANT: For best performance,
keep mower housing free of built-up
grass and trash. Clean the underside of
_ur mower after each use,
CAUTION: Disconnect spark plug wire
from spark plug and place wire where it
cannot come in contact with the spark
plug.
•Clean the underside of your lawn
mower by scraping to remove build-up
of grass and trash.
•Clean engine often to keep trash from
accumulating. Aclogged engine runs
hotter and shortens engine life.
•Keep finished surfaces and wheels free
of all gasoline, oil, etc.
•We do not recommend using a garden
hose to clean lawn mower unless the
electrical system, muffler, air filter and
carburetor are covered to keep water
out. Water in engine can result in
shortened engine life.
CLEAN UNDER DRIVE COVER
Clean under drive cover at least twice a
season. Scrape underside of cover with
putty knife or similar tool to remove any
build-up of trash or grass on underside of
drive cover.
_WARNING: To avoid serious injury,
before performing any service or adjust-
ments:
1. Release control bar and stop engine.
2. Make sure the blade and all moving
parts have completely stopped.
3. Disconnect spark plug wire from spark
plug and place where it cannot come
in contact with plug.
LAWN MOWER
TO ADJUST CUTTING HEIGHT
See "TO ADJUST CUTTING HEIGHT" in
the Operation section of this manual.
REAR DEFLECTOR
The rear deflector, attached between the
rear wheels of your mower, is provided to
minimize the possibility that objects will
be thrown out of the rear of the mower
into the operator's mowing position. If the
deflector becomes damaged, it should be
replaced.
13

TO REMOVE DRIVE BELT
1. Remove drive cover. Remove belt
from gearcase pulley by pushing
down on pulley and rolling belt off it,
2. Turn lawn mower on its side with air
filter and carburetor up.
3. Remove blade.
4. Remove debris shield.
5. Remove belt from engine pulley on
crankshaft.
TO REPLACE DRIVE BELT
1. Install new belt on engine pulley.
2. Reinstall debris shield and blade.
3. Return mower to upright position.
4. Install new belt on gearcase pulley.
5. Reinstall drive cover.
NOTE: Always use factory approved belt
to assure fit and long life.
Drive
cover
PUSH
TO ADJUST HANDLE
The handle can be mounted in a high or
low position. The mounting holes in the
bottom of lower handle are off center for
raising or lowering the handle.
NOTE: The upper handle has an "anti-
fold" bracket located on the left side of the
handle. This bracket prevents the upper
handle from folding forward, which helps
protect control cable(s) from damage.
1. Remove upper handle and all parts
attached to lower handle.
2. Remove hairpin cotters from lower
handle bracket mounting pin.
3. Squeeze lower handle in to remove it
from mounting pins.
4. Turn lower handle over to raise or
lower handle.
5. Squeeze lower handle in and position
holes onto mounting pins on handle
bracket.
6. Reassemble upper handle and all
parts removed from lower handle.
Anti-fold
bracket
Lower
handle
ROTATE
ENGINE
ENGINE SPEED
Your engine speed has been factory set.
Do not attempt to increase engine speed
or it may result in personal injury. If you
believe that the engine is running too fast
or too slow, take your lawn mower to a
Sears or other qualified service center for
repair and adjustment.
CARBURETOR
Your carburetor has a non-adjustable
fixed main jet for mixture control. If your
engine does not operate properly due to
suspected carburetor problems, take your
lawn mower to a Sears or other qualified
service center for repair and/or adjust-
ment.
IMPORTANT: Never tamper with the
engine governor, which is factory set for
proper engine speed. Overspeeding the
engine above the factory high speed
setting can be dangerous. If you think the
engine-governed high speed needs
adjusting, contact a Sears or other
qualified service center, which has proper
equipment and experience to make any
necessary adjustments.
14

Immediately prepare your lawn mower for
storage at the end of the season or if the
unit will not be used for 30 days or more.
LAWN MOWER
When lawn mower is to be stored for a
period of time, clean it thoroughly, remove
all dirt, grease, leaves, etc. Store in a
clean, dry area.
1. Clean entire lawn mower (See
"CLEANING" in the Maintenance
section of this manual).
2. Lubricate as shown in the Mainte-
nance section of this manual.
3. Be sure that all nuts, bolts, screws,
and pins are securely fastened.
Inspect moving parts for damage,
breakage and wear. Replace if
necessary.
4. Touch up all rusted or chipped paint
surfaces; sand lightly before painting.
HANDLE
You can fold your lawn mower handle for
storage.
NOTE: The upper handle has an "anti-
fold" bracket located on the left side of the
handle. This bracket prevents the upper
handle from folding forward, which helps
protect control cable(s) from damage.
1. Squeeze the bottom ends of the lower
handle toward each other until the
lower handle clears the handle
bracket, then move handle forward.
2. Loosen upper handle mounting bolts
enough to allow upper handle to be
folded back.
IMPORTANT: When folding the handle
for storage or transportation, be sure to
fold the handle as shown or you may
damage the control cables.
•When setting up your handle from the
storage position, the lower handle will
automatically lock into the mowing
position.
SQUEEZE
TO FOLD
handk
I
I
I
Operator presence Mowing position
control bar
Lower
FOLD
BACKWARD
bracket
ENGINE
FUEL SYSTEM
IMPORTANT: It is important to prevent
gum deposits from forming in essential
fuel system parts such as carburetor, fuel
filter, fuel hose, or tank during storage.
Also, alcohol blended fuels (called
gasohol or using ethanol or methanol)
can attract moisture which leads to
separation and formation of acids during
storage. Acidic gas can damage the fuel
system of an engine while in storage.
1. Drain the fuel tank.
2. Start the engine and let it run until the
fuel lines and carburetor are empty.
• Never use engine or carburetor cleaner
products in the fuel tank or permanent
damage may occur.
•Use fresh fuel next season.
NOTE: Fuel stabilizer is an acceptable
alternative in minimizing the formation of
fuel gum deposits during storage. Add
stabilizer to gasoline in fuel tank or
storage container. Always follow the mix
ratio found on stabilizer container. Run
engine at least 10 minutes after adding
stabilizer to allow the stabilizer to reach
the carburetor. Do not drain the gas tank
and carburetor if using fuel stabilizer.
ENGINE OIL
Drain oil (with engine warm) and replace
with clean engine oil. (See "ENGINE" in
the Maintenance section of this manual).
CYLINDER
1. Remove spark plug.
2. Pour one ounce (29 ml) of oil through
spark plug hole into cylinder.
3. Pull starter handle slowly a few times
to distribute oil.
4, Replace with new spark plug.
15

OTHER
•Do not store gasoline from one season
to another.
• Replace your gasoline can if your can
starts to rust. Rust and/or dirt in your
gasoline will cause problems.
•If possible, store your unit indoors and
cover it to protect it from dust and dirt.
•Cover your unit with a suitable protec-
tive cover that does not retain mois-
ture. Do not use plastic. Plastic cannot
breathe which allows condensation to
form and willcause your unit to rust.
IMPORTANT: Never cover mower while
engone and exhaust areas are still warm.
_, CAUTION: Never store the lawn mower
with gasoline in the tank inside a building
where fumes may reach an open flame or
spark. Allow the engine to cool before
storing in any enclosure.
TROUBLESHOOTING - See appropriate section in manual unless directed
to a Sears Service Center.
PROBLEM CAUSE
Does not start 1. Dirty air filter.
2. Out of fuel.
3. Stale fuel.
4. Water in fuel.
5. Spark plug wire is
disconnected.
6. Bad spark plug.
7. Loose blade or broken
blade adapter.
8. Control bar in released
position.
9. Control bar defective.
10. Fuel valve lever (if so
equipped) in OFF position.
11.Weak battery (if equipped).
12.Disconnected battery
connector (if equipped).
CORRECTION
1. Clean/replace air filter.
2. Fill fuel tank.
3. Drain tank and refill with
fresh, clean fuel.
4. Drain fuel tank and
carburetor and refill tank
with fresh gasoline.
5. Connect wire to plug.
6. Replace spark plug.
7. Tighten blade bolt or
replace blade adapter.
8. Depress control bar to
handle.
19. Replace control bar.
10.Turn fuel valve lever
to the ON position.
11,Charge battery.
12.Connect battery to engine.
16

TROUBLESHOOTING - See appropriate section in manual unless directed
to a Sears Service Center.
CAUSEPROBLEM
LOSS of power
Poor cut -
uneven
Excessive
vibration
Starter rope
hard to pull
1, Rear of lawn mower
housing or cutting blade
dragging in heavy grass.
2. Cutting too much grass.
3. Dirty air filter.
4. Buildup of grass, leaves,
and trash under mower.
5. Too much oil in engine.
6. Walking speed too fast.
1, Worn, bent or loose blade.
2. Wheel heights uneven.
3. Buildup of grass, leaves
and trash under mower.
1. Worn, bent or loose blade.
2. Bent engine crankshaft.
.
2.
3.
4.
Engine flywheel brake is on
when control bar is released,
Bent engine crankshaft.
Blade adapter broken.
Blade dragging in grass.
CORRECTION
1. Set to "Higher Cut"
position.
2. Set to "Higher Cut"
position.
3. Clean/replace air filter.
4. Clean underside of mower
housing.
5. Check oil level.
6. Cut at slower walking speed.
1. Replace blade. Tighten
blade bolt.
2. Set all wheels at same
height.
3. Clean underside of
mower housing.
1. Replace blade. Tighten
blade bolt.
12. Contact a Sears or other
qualified service center.
! 1. Depress control bar to
upper handle before
pulling starter rope.
2. Contact a Sears or other
qualified service center.
3. Replace blade adapter.
4. Move lawn mower to cut
grass or to hard surface.
Grass catcher 1. Cutting height too low, 1, Raise cutting height.
notfilling 2. Lift on blade worn off. 2. Replace blade.
(Ifsoequipped) 3. Catcher not venting air. 3. Clean grass catcher.
Hard to push 1. Raise cutting height.1. Grass is too high or wheel
height is too low.
2. Rear of lawn mower
housing or cutting blade
dragging in grass.
3. Grass catcher too full.
4. Handle height position not
right for you.
Loss of drive
or slowing of
drive speed
1. Belt wear.
2. Belt off of pulley.
3. Drive cable worn or broken.
4. Dirt in drive pinions.
2. Raise rear of lawn mower
housing one (1) setting
higher.
3. Empty grass catcher,
4. Adjust handle height to suit.
1. Check/replace drive belt.
2. Check/reinstall drive belt.
3. Replace drive cable.
4. Clean drive pinions.
17

Garantia ........................................................ 18
Reglas de Seguddad ............................... 18-20
Montaje /Pre-Operacibn .............................. 21
Operaci6n ................................................ 22.25
Mantenimiento ......................................... 26-29
Programa de Mantenimiento ......................... 26
Especificadones del Producto ..................... 27
Servicio y Adjustes ....................................... 29
Almacenamiento ...................................... 31-32
Identificaci6n de problemas .................... 32-33
Servicio Sears ......................................... 34-43
Orden de Panes ............................ Contratapa
GARANT{A LIMITADA DE DOS ANOS PARA LA SEGADORA A MOTOR CRAFTSMAN
Per dos (2) aries, a partir de la fecha de compra, cuando esta Segadora Craftsman se
mantenga, lubrique y afine segun las instruc¢iones para la operaci6n y el mantenimiento en el
manual del duefio, Sears reparar_, gratis rode defecto en el material y la mane de obra.
Si la Segadora Craftsman se usa para fines comerciales o de arriendo, esta garantia s61o se
aplica per noventa (90) dfas a partir de la fecha de compra.
Esta Garantfa no cubre:
•Artfculos que se desgastan durante el use normal tales come las ¢uchillas segadoras
rotatorias, los adaptadores de la cuchilla, las correas, los filtros de aire y las bujfas.
• Reparaciones necesarias debido al abuse o a la negligencia del operador, incluy_ndose a los
cigL_efiales doblades y a la falta de mantenimiento del equipo seglJn las instrucciones que se
in¢luyen en el manual del dueflo.
EL SERVICIO DE GARANTfA ESTA DISPONIBLE al devolver la segadora a motor Craftsman al
centro/departmento de servicio Sears mas ¢ercano en los Estados Unidos. Esta garantfa se
aplica sotamente mientras el producto este en use en los Estados Unidos.
Esta Garantfa le otorga derechos legales especifices, y puede que tambi_n tenga otros
derechos que varfan de estado aestado.
SEARS, ROEBUCK AND CO., D/817WA, HOFFMAN ESTATES, IL 60179 USA
IMPORTANTE: Esta maquina cortadaora es capaz de amputar las manes y los manes y los
pies y de lanzar objetos, Si no se observan las instruccionesde seguridad siguientes se pueden
producir lesiones graves o la muerte.
_Busque este sfmbolo que sefiala las
precauciones de seguridad de importancia.
Quiere decir - iltATENCION!!!iilESTE
ALERTOH! SU SEGURIDAD ESTA
COMPROMETIDA.
_ADVERTENCIA: Siempre desconecte el
alambre de la bujia y p6ngalo donde no pueda
entrar en contacto con la bujfa, para evitar el
arranque por accidente, durante la
preparaci6n, el transporte, el ajuste o cuando
se hacen reparaciones.
_ADVERTENCIA: Los bornes, terminales y
accesodos relatives de la bateria contienen
plomo o compuestos de plomo, productos
qufmicos conocidos en el Estado de California
come causa de c&ncer y defectos al
nacimianto u otroa dafios reproductivos. Lavar
las manes despu6s de manlpularlos.
,_I,PRECAIJCI6N: El tube de escape del
motor, algunos de sus constituyentes y
algunos componentes del vehiculo contienen
o desprenden productos quimicos conocidos
en el Estado de California come causa de
cdncer y defectos al nacimiento u otros dar_os
reproductivos.
_PRECAUCK_N: El silenciadory otras
piezas del motor Ilegan a sre extremadamente
calientes durante la operacibn y siguen siendo
¢alientes despu6s de que el motor haya
parade. Para evitar quemaduras severas,
perrnanezca lejos de estas dreas.
18

I, OPERACION
• Antes de empezar, debe familiarizarse
completamente con los controles yel uso
correcto de la maquina. Para esto, debe leer
ycomprender todas las instrucciones que
aparecen en la maquina yen los manuales
de operacibn.
•No ponga las manos o los pies cerca o
debajo de las partes rotatorias. Mantengase
siempre lejos de la abertura de la descarga.
• Permita que solamente las personas
responsables que est_n familiarizadas con
las instrucciones operen la maquina.
•Despeje el _.rea de objetos tales como
piedras, juguetes, alambres, huesos, palos,
etc. que pueden ser recogidos y lanzados
por las cuchillas.
•Aseg'3rese que el _rea no se hallen
personas, antes de segar. Pare la m_.quina
si alguien entra en el drea.
•No opere la maquina sin zapatos o con
sandalias abiertas. Pbngase siempre
zapatos s61idos.
• No tire de la segadora hacia atr_s a menos
que sea absolutamente necesario. Mire
siempre hacia abajo yhacia detr<_santes y
mientras que se mueve hacia atr&s.
• No opere la segadora sin los respectivos
resguardos, las placas, el recogedor de
c_sped u otms aditamentos dise ados para
su pmtecci6n yseguridad.
•Refi_rase a las instrucciones del fabricante
para el funcionamiento e instalaci6n de
accesorios. Use 0nicamente accesorios
aprobados por el fabricante.
•Detenga la cuchilla o las cuchillas cuando
cruce pot calzadas, calles o caminos de
grava.
•Parar el motor cada vez que se abandona el
aparato, antes de limpiar la segadora o de
remover residuos del tubo.
•Apagar el motor y esperar hasta que las
cuchiUas estdn completamente paradas
antes de remover el receptor de hierba.
• Segar solamente con luz del dfa o con una
buena luz artificial.
• NO opere la m&quina bajo la influencia del
alcohol o de las drogas.
• Nunca opere la maquina cuando la hierba
est_ mojada. Aseg0rese siempre de tener
buena traccibn en sus pies; mantenga el
mango firmemente y camine; nunea corra.
• Desconectar el mecanismo de propulsi6n
aut6noma o el embrague de transmisi6n en
las segadoras que Io tienen antes de poner
en marcha el motor,
• Si el equipo empezara a vibrar de una
manera anormal, pare el motor y revise de
inmediato para averiguar la causa.
Generalmente la vibraci6n suele indicar que
existe alguna averia.
• Siempre use gafas de seguridad o anteojos
con proteccibn lateral cuando opere la
segadora.
II. OPERACION SOBRE LAS CUESTAS
Los accidentes ocurren con rods frecuencia
en las cuestas. Estos accidentes ocurren
debido a resbaladas o cafdas, las cuales
pueden resultar en graves lesiones. Operar la
recortadora en cuestas requiere mayor
concentraci6n. S! se siente inseguro en una
cuesta, no la recorte.
HACER:
•Puede recortar a tray,s de la superticie de
la cuesta, nunca hacia arriba y hacia abajo.
Proceda con extrema precauci6n cuando
cambie de direcci<_nen las cuestas.
•Renueva todos los objetos extrat_os,tales
come guijarros, ramas, etc.
• Debe prestar atenciSn a hoyos, baches o
protuberancias. Reeuerde que la hierba alta
puede esconder obst&culos.
NO HACER:
• No recorte cerca de pendientes, zanjas o
terraplenes. El operador puede perder la
tracci6n en los pies o el equilibrio.
•No recorte cuestas demasiado inclinadas.
• No recorte en hierba mojada. La reducci6n
en la traceion de la pisada puede causar
resbatoneS.
II1.NINOS
Se pueden producir accidentes tr_,gicos si el
operador no presta atenci6n a la presencia de
los niP=os,A menudo, los nir3os se sienten
atraidos por la m_,quina y por la actividad de la
siega. Nunca suponga que los niSos van a
permanecer en el mismo lugar donde los rio
por 01tima vez.
• Mantenga a los niftos alejados del _rea de la
siega y bajo el cuidado estricto de otra
persona adulta responsable.
• Est_ alerta y apague la md.quina si hay
niSosque entran al _.rea.
•Antes y cuando este retrocodiendo, mire
hacia atrds y hacia abajo para verificar si
hay niSos pequeSos.
• Nunca permita que los niSos operen la
mdquina.
• Tenga un cuidado extra cuando se acerque
a esquinas donde no hay vtsibilidad, a los
arbustos, drboles u otros objetos que
pueden interferir con su Ii"nea de visi6n.
IV. SERVICIO
•Tenga cuidado extra al manejar la gasolina
y los demds combustibles. Son inflamables
ylos gases son explosivos.
-Use solamente un envase aprobado.
- Nunca remueva la tapa del dep6sito de
gasolina o agregue combustible con el
motor funcionando. Permita que el motor
se entree antes de volver apone
combustible. No fume.
- Nunca vuelva a porter combustible en la
mdquina en recintos cerrados.
-Nunca almacene la mdquina o el envase
del combustible dentro de alg0n lugar en
donde haya una llama expuesta, tal como
la del calentador de agua.
19

• Nunca haga funcionar una m_quina dentro
de un &rea cerrada.
•Nunca haga ajustes o reparaciones
mientras el motor est_ en marcha.
Desconecte el cable de la bujla, y
mant_ngalo a clerta distancia de _sta para
prevenir un arranque accidental.
• Mantenga las tuercas y los pernos,
especialmente los pernos del accesono de
la cuchilla, apretados y mantenga el equipo
en buenas condiciones.
• Nunca manipule de forma indebida los
dispositivos de seguddad. Controle
regularmente su funcionamiento correcto,
• Mantenga la m,_quina libre de hierba, hojas
uotras acumulaciones de desperdioio.
Limpie los derrames de aceite o combus-
tible. Permita que la m&quina se enfrle antes
de almacenarla.
• Pare e inspeccione el equipo si le pega a un
objeto. Rep_relo, si es necesario, antes de
hacerlo arrancar.
• En ningen caso hay que regular la altura de
las ruedas mientras el motor est_ en
marcha.
•Los componentes del receptor de la hierba
van sujetos a desgaste, daSos y deterioro,
que pueden exponer las partes en
movimiento o permitir que objetos sean
disparados. Controlar frecuentemente y
cuando sea necesario sustituir con panes
aconsejadas por el fabric.ante.
• Las cuchillas de la segadora est4n afiladas
y pueden cortar. Cubdr las hojas o Uevar
guantes, y utilizar precauciones especiales
cuando se efectua mantenJmiento sobre las
mismas.
• No cambie el ajuste del regulador del motor
nf exceda su velocidad.
Estos accesorios estaban disponibles cuando se produjo la segadora. No son facllitados junto al
cortacesped. Estc'_ndisponibles en la mayoda de las tiendas de Sears yen los centros de servicio. La
mayorfa de las tiendas Sears tambi_n pueden mandar a pedir partes de repuesto para usted,si les
proporcionael n_mero del modelo de su segadera. Algunos de estos accesorios tal vez no se apliquen a
su segadora.
RENDIMIENTO DE LA SEGADORA
DE RECI_TES
pAPA SEC,_I_RI_ _ ESTABILI-
CONDESCN:I_ _RF.S
_RECI_IEI_R _RE_REI_R
SE_I_S SEGN_
MANTENIMIENTO DE LA SEGADORA
81LENCIADORE8
CORRr_I_ CUI_IIU.._
FILTR08 DE AIRE
AD_'I'_R_
DE CUCHILLA RUEDAS ACEITE
DEL MOTOR
20