Craftsman 917.378494 User manual

Owner's Manual
CRIIFTSMItN°
'11
6.75 Horsepower
Power-Propelled
21" Rear Discharge
Model No.
917.378494
EspaSo[, p. 18
CAUTION:
Read and follow a[[
Safety Rules and Instructions
before operating this equipment
Sears, Roebuck and Co., Hoffman Estates, IL 60179
Visit our Craftsman website: www.sears.com/craftsman U.S.A.

L GENERAL OPERATION
*Read, understand, and follow all
instructions on the machine and in the
manual(s) before starting. Be thoroughly
familiar with the controls and the proper
use of the machine before starting.
Do not put hands or feet near or under
rotating parts. Keep clear of the dis-
charge opening at all times.
Only allow responsible individuals, who
are familiar with the instructions, to oper-
ate the machine.
Clear the area of objects such as rocks,
toys, wire, bones, sticks, etc., which
could be picked up and thrown by the
blade.
Be sure the area is clear of other people
before mowing. Stop machine if anyone
enters the area.
Do not operate the mower when bare-
foot or wearing open sandals. Always
wear substantial foot wear.
Do not pull mower backwards unless
absolutely necessary. Always look down
and behind before and while moving
backwards.
Do not operate the mower without
proper guards, plates, grass catcher or
other safety protective devices in place.
See manufacturer's instructions for
proper operation and installation of
accessories. Only use accessories ap-
proved by the manufacturer.
Stop the blade(s) when crossing gravel
drives, walks, or roads.
Stop the engine (motor) whenever you
leave the equipment, before cleaning the
mower or unclogging the chute.
Shut the engine (motor) off and wait until
the blade comes to complete stop before
removing grass catcher.
Mow only in daylight or good artificial
light.
Do not operate the machine while under
the influence of alcohol or drugs.
Never operate machine in wet grass.
Always be sure of your footing: keep a
firm hold on the handle and walk; never
run.
Disengage the self-propeJled mech-
anism or drive clutch on mowers so
equipped before starting the engine
(motor).
If the equipment should start to vibrate
abnormally, stop the engine (motor) and
check immediately for the cause. Vibra-
tion is generally a warning of trouble.
Always wear safety goggles or safety
glasses with side shields when operating
JL SLOPE OPERATION
Slopes are a major factor related to slip
and fall accidents which can result in
severe injury. All slopes require extra cau-
tion. If you feel uneasy on a slope, do not
mow it.
DO:
Mow across the face of slopes: never
up and down. Exercise extreme caution
when changing direction on slopes.
Remove obstacles such as rocks, tree
limbs, etc.
Watch for holes, ruts, or bumps. Tail
grass can hide obstacles.
DO NOT:
'_ Do not trim near drop-offs, ditches or
embankments. The operator couJd lose
footing or balance.
,, Do not trim excessively steep slopes.
,, Do not mow on wet grass. Reduced foot-
ing could cause slipping.
JJL CHILDREN
Tragic accidents can occur if the operator
is not alert to the presence of children.
Children are often attracted to the machine
and the mowing activity. Never assume
that children will remain where you last
saw them.
Keep children out of the trimming area
and under the watchfuJ care of another
responsible adult.
Be alert and turn machine off if children
enter the area.
Before and while walking backwards,
look behind and down for small children.
Never allow children to operate the ma-
chine.
Use extra care when approaching blind
corners, shrubs, trees, or other objects
that may obscure vision.
iV. SERVICE
Use extra care in handling gasoline and
other fuels. They are flammable and
vapors are explosive.
-Use only an approved container.
- Never remove gas cap or add fuel
with the engine running.
Allow engine to cool before refueling.
Do not smoke.
-Never refuel the machine indoors.
- Never store the machine or fuel
container inside where there is an
open flame, such as a water heater.
Never run a machine inside a closed area.
Never make adjustments or repairs with
the engine (motor) running. Disconnect the
spark plug wire, and keep the wire away
from the plug to prevent accidental starting.
mower. 3

Keep nuts and bolts, especially blade
attachment bolts, tight and keep equip-
ment in good condition.
Never tamper with safety devices. Check
their proper operation regularly.
Keep machine free of grass, leaves, or
other debris build-up. Clean oil or fuel spill-
age. Allow machine to cool before storing.
Stop and inspect the equipment if you
strike an object. Repair, if necessary,
before restarting.
Never attempt to make wheel height adjust-
ments while the engine (motor)is running.
Grass catcher components are subject
to wear, damage, and deterioration,
which could expose moving parts or
allow objects to be thrown. Frequently
check components and replace with
manufacturer's recommended parts,
when necessary.
Mower blades are sharp and can cut.
Wrap the blade(s) or wear gloves, and
use extra caution when servicing them.
Do not change the engine governor set-
ting or overspeed the engine.
Serial Number:
Date of Purchase:
Gasoline Capacity /Type: 1.6 Quarts (Unleaded Regular)
Oil Type (API-SF-SJ): SAE 30 (above 32°F); SAE 5W-30 (below 32°F)
Oil Capacity: 20 Ounces
Spark Plug (Gap: .030") Champion RJ19LM or J19LM
Blade Bolt Torque: 35-40 ft. Ibs.
The model and serial numbers will be found on a decal on the rear of the lawn mower
housing. Record both serial number and date of purchase in space provided above.
Repair Protection Agreements
Congratulations on making a smart pur-
chase. Your new Craftsman® product is
designed and manufactured for years of
dependable operation. But like all prod-
ucts, it may require repair from time to
time. That's when having a Repair Protec-
tion Agreement can save you money and
aggravation.
Purchase a Repair Protection Agreement
now and protect yourseff from unexpected
hassle and expense.
Here's what's included in the Agreement:
Expert service by our 12,000 profe-
sional repair specialists.
Unmimited service and no charge for
parts and labor on all covered repairs.
Product repmacement if your covered
product can't be fixed.
• Discount of 10% from regular price of
service and service-related parts not
covered by the agreement; also, 10%
off regular price of preventive mainte-
nance check.
Fast hemp by phone - phone support
from a Sears technician on products
requiring in-home repair, plus conve-
nient repair scheduling.
Once you purchase the Agreement, a
simple phone call is all that it takes for you
to schedule service. You can call anytime
day or night, or schedule a service ap-
pointment online.
Sears has over 12,000 professional repair
specialists, who have access to over 4.5
million quality parts and accessories.
That's the kind of professionalism you can
count on to help prolong the life of your
new purchase for years to come. Purchase
your Repair Protection Agreement today!
Some mimitations and excmusions appmy.
For prices and additional information
call 1o800o827o6655o
Sears Installation Service
For Sears professional installation of home
appliances, garage door openers, water
heaters, and other major home items, in
the U.S.A. call l o800=4=MYoHOME®.

These accessories were available when this lawn mower was produced. They are not
shipped with your mower. They are also available at most Sears retail outlets and
service centers. Some of these accessories may not apply to your lawn mower.
LAWN MOWER PERFORMANCE
CLIPPING
DEFLECTORS
FOR
REAR DISCHARGE
LAWN MOWERS
GRASS CATCHERS
FOR
REAR DISCHARGE
LAWN MOWERS
STABILIZER
GRASS CATCHERS
FOR
SIDE DISCHARGE
LAWN MOWERS
LAWN MOWER MAINTENANCE
MUFFLERS
BELTS BLADES BLADE ADAPTERS
AIR FILTERS
WHEELS
SPARK PLUGS
ENGINE OIL

These accessories were available when this lawn mower was produced. They are not
shipped with your mower. They are also available at most Sears retail outlets and
service centers. Some of these accessories may not apply to your lawn mower.
LAWN MOWER PERFORMANCE
CLIPPING
DEFLECTORS
FOR
REAR DISCHARGE
LAWN MOWERS
GRASS CATCHERS
FOR
REAR DISCHARGE
LAWN MOWERS
STABILIZER
GRASS CATCHERS
FOR
SIDE DISCHARGE
LAWN MOWERS
LAWN MOWER MAINTENANCE
MUFFLERS
BELTS BLADES BLADE ADAPTERS
AIR FILTERS
WHEELS
SPARK PLUGS
ENGINE OIL

KNOWYOUR LAWN MOWER
READ THIS OWNER'S MANUAL AND ALL SAFETY RULES BEFORE OPERATING
YOUR LAWN MOWER. Compare the illustrationswithyourlawn mowerto familiarize
yourselfwith the locationof variouscontrolsand adjustments. Save thismanual for
futurereference.
These symbols may appear on your lawn mower or In literature supplied with the
product. Learn and understand their meaning.
CAUTION ENGINE ENGINE FAST SLOW CHOKE FUEL OIL DANGER, KEEPHANDS
OR WARNING ON OFF AND FEET AWAY
Operator presence control bar
control
bar
Starter Engine oil cap with dipstick
Grass
catcher
Primer
Muffler
Gasoline filler
Airfiltel
Housing
Wheel adjuster (on each wheel)
IMPORTANT: This lawn mower is shipped WITHOUT OIL OR GASOLINE in the engine.
MEETS CPSC SAFETY REQUIREMENTS
Sears rotary walk-behind power lawn mowers conform to the safety standards of the
American National Standards Institute and the U.S. Consumer Product Safety Com-
mission. The blade turns when the engine is running.
Operator presence control bar - must
be held down to the handle to start the
engine. Release to stop the engine.
Starter handle -used for starting engine.
Drive control bar - used to engage
power-propelled forward motion of mower.
Primer - pumps additional fuel from the
carburetor to the cylinder for use when
7 starting a cold engine.

The operation of any lawn
mower can resultinforeign
objectsthrown intothe
eyes, which can resultin
severe eye damage. Always
wear safety glasses or eye shieldswhile
operatingyourlawn mower orperforming
any adjustmentsor repairs.We recom-
mend a standard safety glasses orwide
vision safetymask worn over spectacles.
HOWTO USEYOUR LAWN MOWER
ENGINESPEED
The engine speed was set at the factory
for optimumperformance. Speed isnot
adjustable.
ENGINE ZONE CONTROL
_,CAUTION: Federal regulations require
an engine control to be installed on this
lawn mower in order to minimize the
risk of blade contact injury. Do not under
any circumstances attempt to defeat the
function of the operator control. The blade
turns when the engine is running.
• Your lawn mower is equipped with an
operator presence control bar which
requires the operator to be positioned
behind the lawn mower handle to start
and operate the lawn mower.
DRIVE CONTROL
• Self-propelling is controlled by hold-
ing the operator presence control bar
down to the handle and pulling the drive
control bar up to the handle. The closer
to the handle the bar is pulled, the faster
the unit will travel.
•Forward motion will stop when either the
operator presence control bar or drive
control bar are released. To stop forward
motion without stopping engine, release
the drive control bar only. Hold operator
presence control bar down against handle
tocontinue mowing without self-propelling.
NOTE: If after releasing the drive control
the mower will not roll backwards, push
the mower forward slightly to disengage
drive wheels.
• To keep drive control engaged when
turning corners, push down on the
handle to lift the front wheels off the
ground while turning lawn mower.
DRIVE CONTROL ADJUSTMENT
Over time, the drive control system may
become "loose", resulting in decreased
speed. There is a thumbscrew on the
underside of the drive control housing to
increase tension on the drive cable. Pro-
ceed as follows:
1. Turn unitoff and disconnect spark plug
wire from spark plug.
2. Rotate thumbscrewcounter-clockwise
to tightenthe drivecable.
3. Operate mower to test drivespeed.
4. If conditionfails to improveafterthe
above steps (forwardspeed remains
the same), your drivebelt is wornand
shouldbe replaced.
NOTE: If mower beginsto "creep" forward,
the drivecable istoo tight. Rotatethumb-
screwclockwiseto loosendrivecable.
0bar
control bar
DRIVE DRIVE
CONTROL CONTROL
ENGAGED DISENGAGED
TO ADJUST CUTTING HEIGHT
Raise wheels for low cut and lower wheels
for high cut, adjust cutting height to suit
your requirements. Medium position is
best for most lawns.
•To change cutting height, squeeze ad-
juster lever toward wheel. Move wheel
up or down to suit your requirements. Be
sure all wheels are in the same setting.
NOTE: Adjuster is properly positioned
when plate tab inserts into hole in lever.
Also, 9-position adjusters (if so equipped)
allow lever to be positioned between the
plate tabs.
LEVER BACKWARD
TO LOWER MOWER
LEVER FORWARD TO RAISE MOWER Lever
TO CONVERT MOWER
Your lawn mower was shipped ready to be
used as a mulcher. To convert to bagging:
•Lift rear door of the lawn mower and
place the grass catcher frame hooks
onto the door pivot pins.
•To convert to mulching operation, re-
move grass catcher and close rear door.
CAUTION: Do not run your lawn mower
without rear door closed, clipping deflector
or approved grass catcher in place. Never
attempt to operate the lawn mower with
the rear door removed or propped open.
8

Rear Grass
catcher
handle
\
Catcher frame hook
TO EMPTY GRASS CATCHER
1. Lift up on grass catcher using the
frame handle.
2. Remove grass catcher with clippings
from under lawn mower handle.
3. Empty clippings from bag using both
frame handle and bag handle.
NOTE: Do not drag the bag when empty-
ing; it will cause unnecessary wear.
Grass
catcher
frame
handle
Bag
handle
ADD GASOLINE
• Fill fuel tank to bottom of tank filler neck.
Do not overfill. Use fresh, clean, regular
unleaded gasoline with a minimum of
87 octane. Do not mix oil with gasoline.
Purchase fuel in quantities that can be
used within 30 days to assure fuel fresh-
ness.
CAUTION: Wipe off any spilled oil or
fuel. Do not store, spill or use gasoline
_ar an open flame.
CAUTION: Alcohol blended fuels
(called gasohol or using ethanol or metha-
nol) can attract moisture which leads to
separation and formation of acids during
storage. Acidic gas can damage the fuel
system of an engine while in storage. To
avoid engine problems, the fuel system
should be emptied before storage of 30
days or longer. Empty the gas tank,' start
the engine and let it run until the fuel lines
and carburetor are empty. Use fresh fuel
next season. See Storage Instructions for
additional information. Never use engine
or carburetor cleaner products in the fuel
tank or permanent damage may occur.
Engine
oil cap
BEFORE STARTING ENGINE
ADD OIL
Your lawnmower is shipped without oil in
the engine. For type and grade of oil to
use, see UENGINE" in the Maintenance
section of this manual.
ACAUTION: DO NOT overfill engine with
oil, or it will smoke heavily from the muffler
on startup.
1. Be sure lawnmower is level.
2. Remove oil dipstick from oil fill spout.
3. You receive a container of oil with the
unit. Slowly pour the entire container
down the oil fill spout into the engine.
4. Insert and tighten dipstick.
IMPORTANT:
•Check oil level before each use. Add oil
if needed. Fill to full line on dipstick.
•Change the oil after every 25 hours of
operation or each season. You may
need to change the oil more often
under dusty, dirty conditions. See "TO
CHANGE ENGINE OIL" in the Mainte-
nance section of this manual.
Gasoline
filler cap
Primel
TO STOP ENGINE
•Tostopengine, release operator pres-
ence controlbar.
TO START ENGINE
NOTE: Due to protective coatings on the
engine, a small amount of smoke may be
present during the initial use of the prod-
uct and should be considered normal.
1. To start a cold engine, push primer
three (3) times before trying to start.
Use a firm push. This step is not
usually necessary when starting an
engine which has already run for a few
minutes.
2. Hold operator presence control bar
down to the handle and pull starter
handle quickly. Do not allow starter
9 rope to snap back.

NOTE: In coolerweather it may be neces-
saryto repeat primingsteps.In warmer
weather overprimingmaycause flooding
and engine will notstart.If you do flood
engine,wait a few minutesbeforeattempt-
ingto start and do not repeat priming
steps.
MOWING TIPS
• Under certain conditions, such as very
tall grass, it may be necessary to raise
the height of cut to reduce pushing
effort and to keep from overloading the
engine and leaving clumps of grass clip-
pings. It may also be necessary to re-
duce ground speed and/or run the lawn
mower over the area a second time.
•For extremely heavy cutting, reduce the
width of cut by overlapping previously
cut path and mow slowly.
•For better grass bagging and most cut-
ting conditions, the engine speed should
be set in the FAST position.
•When using arear discharge lawn
mower in moist, heavy grass, clumps
of cut grass may not enter the grass
catcher. Reduce ground speed (pushing
speed) and/or run the lawn mower over
the area a second time.
•If a trail of clippings is left on the right
side of a rear discharge mower, mow in
a clockwise direction with a small over-
lap to collect the clippings on the next
pass.
• Pores in cloth grass catchers can be-
come filled with dirt and dust with use
and catchers will collect less grass. To
prevent this, regularly hose catcher off
with water and let dry before using.
•Keep top of engine around starter clear
and clean of grass clippings and chaff.
This will help engine air flow and extend
engine life.
MULCHING MOWING TIPS
IMPORTANT: For best performance,
keep mower housing free of built-up
grass and trash. See =CLEANING" in the
Maintenance section of this manual.
• The special mulching blade will recut
the grass clippings many times and
reduce them in size so that as they fall
onto the lawn they will disperse into
the grass and not be noticed. Also, the
mulched grass will biodegrade quickly
to provide nutrients for the lawn. Always
mulch with your highest engine (blade)
speed as this will provide the best recut-
ting action of the blades.
•Avoid cutting your lawn when it is wet.
Wet grass tends to form clumps and
interferes with the mulching action. The
best time to mow your lawn is the early
afternoon. At this time the grass has
dried, yet the newly cut area will not be
exposed to direct sunlight.
•For best results, adjust the lawn mower
cutting height so that the lawn mower
cuts off only the top one-third of the
grass blades. If the lawn is overgrown it
will be necessary to raise the height of
cut to reduce pushing effort and to keep
from overloading the engine and leaving
clumps of mulched grass. For extremely
heavy grass, reduce your width of cut
by overlapping previously cut path and
mow slowly.
MAX I/3
• Certain types of grass and grass
conditions may require that an area be
mulched a second time to completely
hide the clippings. When doing a sec-
ond cut, mow across (perpendicular) to
the first cut path.
•Change your cutting pattern from week
to week. Mow north to south one week
then change to east to west the next
week. This will help prevent matting and
graining of the lawn.
10

MAINTENANCE BEFORE fVE
EACH 25 HOURS BEFORE
SCHEDULE USE ORB SON S ORAQE
CheckforLoose Fasteners _
L Clean/InspectGrassCatcher*
CheckTires *** _/
NI_CheckDriveWheels
Clean Lawn Mower .... I_ I/
Clean under Drive Cooer *** I_
Check Drive Belt/Pulleys *** _,
_Check /Sharpen /Replace Blade ;,o
R Lubrication
Clean and Recharge Battery ** II/ ll_
Check Engine Oil level I_
_Change Engine Oil
Clean Air Filter
i1_ Inspect Muffler
Replace Spark Plug_Replace Air Filter Paper Cartridge
Empty fuel system or add Stabilizer l#_
• (ffsoequ_oed)
•* Electric-Startmowers
•** Power-Propelledmowers
•*** Use a scraper
to cleanunder deck
1 - Change more often ifoperatingunder a heavy load or In highoutdoortemperatures,
2-Service moreoften ifoperating indirty or dusty conditions.
3-Replace blades more often when mowingin sandy soil.
4-Charge 48 hoursat end of season.
5-And after each 5 hoursof use.
GENERAL RECOMMENDATIONS
The warranty on this lawn mower does not
cover items that have been subjected to
operator abuse or negligence. To receive
full value from the warranty, operator must
maintain unit as instructed in this manual.
Some adjustments will need to be made
periodically to properly maintain your unit.
LUBRICATION CHART
(_) Wheel
juster(on
ch wheel)
At least once a season, check to see if
you should make any of the adjustments
described in the Service and Adjustments
section of this manual.
•At least once a year, replace the spark
plug, clean or replace air filter element
and check blade for wear. Anew spark
plug and clean/new air filter element
assure proper air-fuel mixture and help
your engine run better and last longer.
•Follow the maintenance schedule in this
manual.
BEFORE EACH USE
•Check engine oil level.
•Check for loose fasteners.
LUBRICATION
Keep unit well lubricated
(See "LUBRICATION CHART").
(!) Rear door
hinge
(_ Handle bracket mounting pins
_Spray lubricant
See "ENGINE" In Maintenance section.
IMPORTANT: Do not oil or grease plastic
wheel bearings. Viscous lubricants will
attract dust and dirt thatwill shorten the lifeof
the self-lubricating bearings. If you feel they
must be lubricated, useonly a dry,powdered
11graphite type lubricant sparingly.

LAWN MOWER
Alwaysobservesafetyruleswhen per-
forming any maintenance.
TIRES
•Keep tires free of gasoline, oil, or insect
control chemicals which can harm rubber.
•Avoid stumps, stones, deep ruts, sharp
objects and other hazards that may
cause tire damage.
DRIVE WHEELS
Check front drive wheels each time before
you mow to be sure they move freely.
The wheels not turning freely means trash,
grass cuttings, etc.are inthe drive wheel area
and must be cleaned to free drive wheels.
If necessary to clean the drive wheels, be
sure to clean both front wheels.
1. Remove hubcaps, Iocknuts & washers.
2. Remove wheels from wheel adjusters.
3. Remove any trash or grass cuttings
from inside the dust cover, pinion and/
or drive wheel gear teeth.
4. Put wheels back in place.
NOTE: If after cleaning, the drive wheels
do not turn freely, contact a Sears or other
qualified service center.
BLADE CARE
For best results, blade must be kept sharp.
Replace bent or damaged blades.
TO REMOVE BLADE
1. Disconnect spark plug wire from spark
plug and place wire where it cannot
come in contact with plug.
2. Turn lawn mower on its side. Make
sure air filter and carburetor are up.
3. Use a wood block between blade and
mower housing to prevent blade from
turning when removing blade bolt.
NOTE: Protect your hands with gloves
and/or, wrap blade with heavy cloth.
4. Remove blade bolt by turning counter-
clockwise.
5. Remove blade & attaching hardware
(bolt, lock washer & hardened washer).
TO REPLACE BLADE
1. Position blade on the blade adapter
aligning the two (2) holes in the blade
with the raised lugs on the adapter.
2. Be sure the trailing edge of blade (oppo-
site sharp edge) is up toward the engine.
3. Install the blade bolt with the lock
washer and hardened washer into
blade adapter and crankshaft.
4. Use block of wood between blade and
lawn mower housing and tighten the
blade bolt, turning clockwise.
• The recommended tightening torque is
35-40 ft. Ibs. 12
IMPORTANT: Blade boltis heat treated.
If boltneeds replacing,replace only with
approvedboltshownin the Repair Parts
sectionofthis manual.
Blade adapter Crankshaft
Key _keyway
Blade
Blade
bolt shaft
washer Trailing edge Blade adapter
TO SHARPEN BLADE
NOTE: We do not recommend sharpening
the blade - but if you do, be sure the blade
is balanced.
Care should be taken to keep the blade bal-
anced. An unbalanced blade will cause even-
tual damage to lawn mower or engine.
•The blade can be sharpened with a file
or on a grinding wheel. Do not attempt
to sharpen while on the mower.
•To check blade balance, drive a nail into
a beam or wall. Leave about one inch of
the straight nail exposed. Place center
hole of blade over the head of the nail.
If blade is balanced, it should remain in
a horizontal position. If either end of the
blade moves downward, sharpen the
heavy end until the blade is balanced.
GRASS CATCHER
•The grass catcher may be hosed with
water, but must be dry when used.
• Check your grass catcher often for dam-
age or deterioration. Through normal
use it will wear. If catcher needs replac-
ing, replace only with approved replace-
ment catcher shown in the Repair Parts
section of this manual. Give the lawn
mower model number when ordering.
GEAR CASE
•To keep your drive system working
properly, the gear case and area around
the drive should be kept clean and free
of trash build-up. Clean under the drive
cover twice a season.
• The gear case is filled with lubricant to
the proper level at the factory. The only
time the lubricant needs attention is if
service has been performed on the gear
case.
If lubricant is required, use only ELF
Multis EP00. Do not substitute.

ENGINE
LUBRICATION
Use only high quality detergent oil rated with
API service classification SF-SJ. Select the
oil's SAE viscosity grade according to your
expected operating temperature.
SAE VISCOSITY GRADES
-20 0 30 32 40
-30 -20 -10 0 t0 20 30 40
TEMPERATURE RANGE ANTICIPATED BEFORE NEXT OiL
NOTE: Although multi-viscosity oils
(5W30, 10W30 etc.) improve starting in
cold weather, these multi-viscosity oils will
result in increased oil consumption when
used above 32°E Check your engine oil
level more frequently to avoid possible
engine damage from running low on oil.
Change the oil after every 25 hours of op-
eration orat least once a year if the mower
is not used for 25 hours in one year.
Check the crankcase oil level before
starting the engine and after each five (5)
hours of continuous use. Tighten oil plug
securely each time you check the oil level.
TO CHANGE ENGINE OIL
NOTE: Before tipping lawn mower to drain
oil, empty fuel tank by running engine until
fuel tank is empty.
1. Disconnect spark plug wire from spark
plug and place wire where it cannot
come in contact with plug.
2. Remove engine oil cap; lay aside on a
clean surface.
3. Tip lawn mower on its side as shown
and drain oil into a suitable container.
Rock lawn mower back and forth to re-
move any oil trapped inside of engine.
6. Stop adding oil when you roach the
FULL mark on the dipstick. Wait a
minute to allow oil to settle.
7. Continue adding small amounts of oil,
rechecking the dipstick until oil level
settles at FULL. DO NOT overfill, or
engine will smoke heavily from the
muffler on startup.
8. Always be sure to retighten oil dipstick
before starting engine.
9. Reconnect spark plug wira tospark plug.
AIR FILTER
Yourengine willnot run properly and
maybe damaged by usinga dirtyair
filter. Replacethe airfilter cartridgeevery
100 hoursof operationorevery season,
whicheveroccursfirst. Serviceair cleaner
moreoftenunder dustyconditions.
TO CLEAN AIR FILTER
1. Loosen screw and tilt cover to remove.
2. Carefully remove cartridge.
3. Clean by gently tapping on a fiat sur-
_k face. Ifvery dirty, replace cartridge.
CAUTION: Petroleum solvents, such
as kerosene, are not to be used to clean
cartridge. They may cause deterioration
of the cartridge. Do not oil cartridge. Do
not use pressurized air to clean or dry
cartridge.
4. Install cartridge, then replace cover
making sure the tabs are aligned with
the slots in the back plate. Fasten
screw securely.
Back
Slots
Cover
Cartridge Cover tabs
MUFFLER
Inspect and replace corroded muffler as it
could create a fire hazard and/or damage.
Container
4. Wipe off any spilled oil from lawn
mower or side of engine.
5. Slowly pour oil down the oil fill spout,
stopping every few ounces to check the
SPARK PLUG
Replace spark plug at the beginning of
each mowing season or after every 100
hours of operation, whichever occurs
first. Spark plug type and gap setting
are shown in the =PRODUCT SPECIFIC-
ATIONS" section of this manual.
oil level with the dipstick. 13

CLEANING
IMPORTANT: For best performance, keep
mower housing free of built-grass and
trash. Clean the underside of your mower
after each use.
_CAUTION: Disconnect spark plug wire
from spark plug and place wire where it
cannot come in contact with plug.
•Clean the underside of your lawn mower
by scraping to remove build-up of grass
and trash.
•Clean engine often to keep trash from
accumulating. A clogged engine runs
hotter and shortens engine life.
•Keep finished surfaces and wheels free
of all gasoline, oil, etc.
•We do not recommend using a garden
hose to clean lawn mower unless the
electrical system, muffler, air filter and
carburetor are covered to keep water
out. Water in engine can result in short-
ened engine life.
CLEAN UNDER DRIVE COVER
Clean under drive cover at least twice a
season. Scrape underside of cover with
putty knife or similar tool to remove any
build-up of trash or grass on underside of
drive cover.
_kWARNING: To avoid serious injury,
before performing any service and
adjustments:
1. Release control bar and stop engine.
2. Make sure the blade and all moving
parts have completely stopped.
3. Disconnect spark plug wire from spark
plug and place wire where itcannot
come in contact with plug.
LAWN MOWER
TO ADJUST CUTTING HEIGHT
See =TO ADJUST CUTTING HEIGHT" in
the Operation section of this manual.
REAR DEFLECTOR
The rear deflector, attached between the
rear wheels of your mower, is provided to
minimize the possibility that objects will
be thrown out of the rear of the mower
into the operator mowing position, Ifthe
deflector becomes damaged, it should be
replaced.
TO REMOVE DRIVE BELT
1. Remove drive cover and belt keeper.
2. Remove belt from gearcase pulley by
pushing down on pulley and rolling belt
off it.
3. Turn lawn mower on its side with air
filter and carburetor down.
4. Remove blade and debris shield.
5. Remove belt from engine pulley on
crankshaft.
TO REPLACE DRIVE BELT
1. Install new belt on engine pulley.
2. Reinstall debris shield and blade.
3. Return mower to upright position.
4. Install new belt on gearcase pulley.
5. Reinstall belt keeper and drive cover.
NOTE: Always use factory approved belt
to assure fit and long life.
Drive
cover
Belt keeper
PUSH DOWN
TO ADJUST HANDLE
The handle can be mounted in a high or
low position. The mounting holes in the
bottom of lower handle are off center for
raising or lowering the handle.
1. Remove upper handle and wire tie(s)
securing cable(s) to lower handle.
2. Remove hairpin cotters from lower
handle bracket mounting pin.
3. Squeeze lower handle in to remove it
from mounting pins.
4. Turn lower handle over to raise or
lower handle.
5. Squeeze lower handle in and position
holes onto mounting pins on handle
bracket.
6. Reassemble upper handle and all
parts removed from lower handle.
Mowing Mowing
position _"_ n, posiUon ["_
/I , C-\ /- t i
III I
IfII
I I / I
li I11 /
I I I I
cotter--_ :_'_ "l_"l_.Handle __/
Mounting- _,lJJ bracket _
pin _ _
14 LOW POSITION HIGH POSITION

'\!"_ \
Lower
handl(
ROTATE
ENGINE
ENGINE SPEED
Your engine speed has been factory set.
Do not attempt to increase engine speed
or it may result in personal injury. If you
believe that engine is running too fast or
too slow, take your mower to a Sears or
other qualified service center for repair
and adjustment.
CARBURETOR
Your carburetor is not adjustable. If your
engine does notoperate properly due tosus-
pected carburetor problems, take your lawn
mower to a Sears or other qualified service
center for repair and/or adjustment.
IMPORTANT: Never tamper with the
engine governor, which isfactory set
for proper engine speed. Overspeeding
the engine above the factory high speed
setting can be dangerous. If you think
the engine-governed high speed needs
adjusting, contact a Sears or other
qualified service center, which has proper
equipment and experience to make any
necessary adjustments.
Immediately prepare your lawn mower for
storage at the end of the season or if the
unit will not be used for 30 days or more.
LAWN MOWER
When lawn mower is to be stored for a
period of time, clean it thoroughly, remove
all dirt, grease, leaves, etc. Store in a
clean, dry area.
1. Clean entire lawn mower (See
"CLEANING" in the Maintenance sec-
tion of this manual).
2. Lubricate as shown in the Maintenance
section of this manual.
3. Be sure that all nuts, bolts, screws, and
pins are securely fastened. Inspect
moving parts for damage, breakage
and wear. Replace if necessary.
4. Touch up all rusted or chipped paint
surfaces; sand lightly before painting.
HANDLE
You can fold your lawn mower handle for
storage.
NOTE: The upper handle has an "anti-fold"
bracket located on the right side of the
handle. This bracket prevents the upper
handle from folding forward, which helps
protect control cable(s) from damage.
1. Squeeze the bottom ends of the lower
handle toward each other until the
lower handle clears the handle bracket,
then move handle forward.
2. Loosen upper handle mounting bolts
enough to allow upper handle to be
folded back. 15
IMPORTANT: When folding the handle for
storage or transportation, be sure to fold
the handle as shown or you may damage
the control cables.
•When setting up your handle from the
storage position, the lower handle will
automatically lock into mowing position.
SQUEEZE
TO FOLD
Operator presence
contro_bar
Lower
Mowing
position

ENGINE
FUEL SYSTEM
IMPORTANT: It is important to prevent
gum deposits from forming in essential
fuel system parts such as carburetor, fuel
filter, fuel hose, or tank during storage.
Also, alcohol blended fuels (called gasohol
or using ethanol or methanol) can attract
moisture which leads to separation and
formation of acids during storage. Acidic
gas can damage the fuel system of an
engine while in storage.
•Empty the fuel tank by starting the en-
gine and letting it run untilthe fuel lines
and carburetor are empty.
•Never use engine or carburetor cleaner
products in the fuel tank or permanent
damage may occur.
•Use fresh fuel next season.
NOTE: Fuel stabilizer is an acceptable
alternative in minimizing the formation of
fuel gum deposits during storage. Add
stabilizer to gasoline in fuel tank or stor-
age container. Always follow the mix ratio
found on stabilizer container. Run engine
at least 10 minutes after adding stabilizer
to allow the stabilizer to reach the car-
buretor. Do not empty the gas tank and
carburetor if using fuel stabilizer.
ENGINE OIL
Drain oil (with engine warm) and replace
with clean engine oil. (See "ENGINE" in
the Maintenance section of this manual).
CYLINDER
1. Remove spark plug.
2. Pour one ounce (29 ml) of oil through
spark plug hole into cylinder.
3. Pull starter handle slowly a few times
to distribute oil.
4. Replace with new spark plug.
OTHER
• Do notstore gasolinefrom one season
to another.
•Replace yourgasolinecan ifyourcan
startsto rust. Rustand/or dirt in your
gasolinewillcause problems.
•If possible, storeyourunitindoorsand
coveritto protectitfrom dustand dirt.
• Coveryour unitwitha suitableprotec-
tivecoverthatdoes notretain moisture.
Do notuse plastic. Plasticcannot
breathe, whichallows condensationto
formand will cause your unitto rust.
IMPORTANT: Never cover mowerwhile
engine and exhaustareas are stillwarm.
_CAUTION: Never storethe lawn mower
with gasolinein the tank insideabuilding
where fumes may reach an open flame
or spark. Allowthe engine to cool before
storingin any enclosure.
TROUBLESHOOTING - See appropriate section in manual unless directed
to a Sears Service Center.
PROBLEM CAUSE CORRECTION
Does not start 1. Dirtyair filter. 1. Clean/replace airfilter.
2. Out of fuel.
3. Stale fuel.
4. Water in fuel.
5. Spark plug wire is
disconnected.
6. Bad spark plug.
7. Loose blade or broken
blade adapter.
8. Control bar in released
position.
9. Control bar defective.
10. Fuel valve lever (if so
equipped) in OFF position.
11. Weak battery (if equipped).
12. Disconnected battery
connector (if equipped).
,
3.
4.
15.
16.
!7.
Fillfuel tank.
Empty fuel tank and refill tank
with fresh, clean gasoline.
Empty fuel tank and refill tank
with fresh, clean gasoline.
Connect wire to plug.
Replace spark plug.
Tighten blade bolt or
replace blade adapter.
8. Depress control bar to
handle.
9. Replace control bar.
10. Turn fuel valve lever
to the ON position.
11. Charge battery.
12. Connect battery to engine.
16

TROUBLESHOOTING - See appropriate section in manual unless directed
to a Sears Service Center.
CAUSEPROBLEM
Loss of power
Poor cut -
uneven
Excessive
vibration
Starter rope
hard to pull
1. Rear of mower housing or
blade dragging in grass.
2. Cutting too much grass.
3. Dirty air filter.
4, Buildup of grass, leaves,
and trash under mower.
5, Too much oil in engine.
6. Walking speed too fast,
1. Worn, bent or loose blade.
2. Wheel heights uneven.
3. Buildup of grass, leaves
and trash under mower.
1. Worn, bent or loose blade.
2. Bent engine crankshaft.
.
2.
3.
4.
Engine flywheel brake is on
when control bar is released.
Bent engine crankshaft.
Blade adapter broken.
Blade dragging in grass.
CORRECTION
1. Raise cutting height.
2. Raise cutting height.
3. Clean/replace air filter.
4. Clean underside of mower
housing.
5. Check oil level.
6. Cut at slower walking speed.
1. Replace blade. Tighten
blade bolt.
2. Set all wheels at same
height.
3. Clean underside of
mower housing.
1. Replace blade. Tighten
blade bolt.
2. Contact a Sears or other
qualified service center.
1. Depress control bar to
upper handle before
pulling the starter rope.
2. Contact a Sears or other
qualified service center.
3. Replace blade adapter.
4. Move lawn mower to cut
grass or to hard surface.
iGrass catcher 1. Cutting height too low. 1. Raise cutting height.
not filling 2. Lift on blade worn off. 2. Replace blade.
(If so equipped) 3. Catcher not venting air. 3. Clean grass catcher.
Hard to push 1. Raise cutting height.1. Grass is too high or wheel
height is too low.
2. Rear of mower housing or
blade dragging in grass.
3. Grass catcher too full.
4. Handle height position not
right for you.
Loss of drive
or slowing of
drive speed
1. Belt wear.
2. Belt off of pulley.
3. Drive cable worn or broken.
4. "Loose" drive control system.
2. Raise rear of mower housing
one (1) setting higher.
3. Empty grass catcher.
4. Adjust handle height to suit.
1. Check/replace drive belt.
2. Check/reinstall drive belt.
3. Replace drive cable.
4. Adjust drive control.
17

Garantfa ......................................................... 18
Reglas de Segurldad ................................ 18-20
Especif'w,aciones del Producto ....................... 20
Montajs /Pre-Operaci6n ............................... 22
Operaci6n ............................................... ,23-26
Mantanlmlento .......................................... 27-30
Programa de Mantenlmlanto ......................... 27
Servicio y Ad|ustes ................................... 30-31
Almacsnamiento ....................................... 31-32
Identificaci6n de problemas ...................... 32-33
Partes de repuesto .................................. 34-43
Servicio Sears .................................. Contratapa
GARANTIA LIMITADA DE DOS AI_IOS PARA LA SEGADORA A MOTOR CRAFTSMAN
Por dos (2) altos, a partir de la fecha de compra, cuando esta Segadora Craftsman se mantenga,
lubdque y afine segt_n las instrucciones para la operaci6n y el mantenimianto en el manual del
due_o, Sears reparard gratis todo defecto en el material y la mano de obra.
SI la Segadora Craftsman se usa para fines comerciales o de arriendo, esta garantfa s61ose aplica
por noventa (90) d|as a par'dr de la fecha de compra.
Esta Garantfa no cubre:
• Articulos que se desgastan durante el uso normal tales como las cuchillas segadoras rotatorias,
los adaptadores de la cuchilla, las corraas, los filtros de aire y las bujfas.
•Reparaciones necesarias debido al abuso o a la negligancia del operador, incluy_ndose a los
cig0e_ales doblados y a la falta de mantenimiento del equipo segt_n las instrucciones que se
incluyan an el manual del due_o.
El servicio de garantia esta disponible al devolver la segadora a motor Craftsman al Centro de
Servicio Sears mas cercano an los Estados Unidos. Esta garantia se aplica solamente mientras el
producto este en uso en los Estados Unidos.
Esta Garantia le otorga derechos legales especfficos, y pusde que tambi_n tenga otros dsrechos
que varian de estado a estado.
Sears, Roebuck and Co., D/817WA, Hoffman Estates, IL 60179 USA
IMPORTANTE: Esta maquina cortadaora es capaz de amputar las manos y los manos y los pies y
de lanzar objetos. Si no se observan las instrucciones de seguridad siguientes ss pueden producir
lesiones graves o la muerte.
/I, Busque este sfmbolo que se_ala las precau-
ciones de seguridad de importancia. Quiera
decir- ilIATENCION!!I iiiESTE ALERTO!!?
SU SEGURIDAD ESTA COMPROMETIDA.
_ADVERTENClA: Siempre desconecte el
alambra de la bujfa y p6ngalo donde no pueda
entrar en contacto con la bujfa, para evitar el
arranque por accidente, durante la preparacibn,
el transporte, el ajuste o cuando se hacen
reparaciones.
_ADVERTENClA: Los bornes, terminales y
accesorios relativos de la bateda contienen
plomo o compuestos de plomo, productos
qufmicos conocidos en el Estado de California
como causa de cdncer y defectos al nacimiento
u otros danos reproductivos. Lavar las manos
despuq_s de manipularlos.
_I_PRECAUCI(_N: El tubo de escape del motor,
algunos de sus constituyentes yalgunos com-
ponentes del vehiculo contienan o desprandan
productos qufmicos conocidos en el Estado de
California como causa de cbncer y defectos al
nacimiento u otros daSos reproductivos.
_PRECAUCI(_N: El silenciador y otras
piezas del motor Ilegan asre extramadamente
calientes durante la operaci6n y siguen siendo
calientss despuds de que el motor haya parado.
Para evitar quemaduras severas, permanezca
lejos de estas dreas.
18

I. OPERACION
• Antes de empezar, debe farnillarlzarse cornple-
tamente con los conb'oles y el uso correcto de
la maqulna. Para esto, debe leer y comprander
todas las Instrucclones que aparecen en la ma-
qulna yen los manualas de operacl(,')n.
• No ponga las manos o los pies cerca o
debaJo de las partas rotatorlas. Mant6ngase .
siempre lejos de la abertura de la descarga.
•Permlta que solamente las personas re-
sponsablas que ast6n familiadzadas con las
instruccionas operen la mdquina.
•Despeje el drea de objetos tales como pie-
dras, juguetas, alambres, huesos, palos, etc.
que pueden ser recogidos y lanzados por las
cuchillas.
• AsegOrase que el drea no se hallen per-
sonas, antes de segar. Pare la mdquina si
alguien entra en el drea.
•No opere la maquina sin zapatos o con sanda-
lias abiertas. P6ngase siempre zapatos s61idos.
•No tire de la segadora hacia atrds a menos
que sea absolutamante necesario. Mire
siempre hacia abajo y hacia detrds antes y
mientras que se mueve hacia atrds.
•No opere la segadora sin los respectivos
resguardos, las placas, el recogedor de
c6sped u otros aditamentos dise ados para
su proteccibn y seguridad.
• Refi6rase alas instrucciones del fabricante
para el funcionamiento e instalaci6n de
accesorios. Use dnicamente accesorios
aprobados por el fabricante.
•Detenga la cuchillao lascuchillas cuando cruce
por calzadas, calles o caminos de grava.
•Parar el motor cada Vez que se abandona el
aparato, antes de limpiar la segadora o de
remover residuos del tubo.
•Apagar el motor y esperar hasta que las
cuchillas estdn completamente paradas
antes de remover el receptor de hierba.
•Segar solamente con luz del dfa o con una
buena luz artificial.
•No opere la mdquina bajo la influencia del
alcohol o de las drogas.
•Nunca opere la maquina cuando la hierba
est6 mojada. AsegOrese siempre de tener
buena tracci6n en sus pies; mantanga el
mango firmemente y camine; nunca corra.
•Desconectar el mecanismo de propulsi6n
aut6noma o el embrague de transmisi6n en
las segadoras que Io tienen antes de poner
en marcha el motor.
•Si el equipo empezara a vibrar de una
manera anormal, pare el motor y revise de
inmediato para averiguar la causa. General-
mente la vibraci6n suele indicar que existe
alguna averia.
•Siempre use gafas de seguridad o anteojos con .
protecci6n lateral cuando opera la segadora.
II. OPERAClON SOBRE LAS CUESTAS
Los accidentes ocurren con mds frecuencia en
las cuestas. Estos accidentes ocurren debldo a
resbaladas o cafdas, las cualas pueden resultar .
en graves lesiones. Operar la recortadora en
cuestas requiere mayor concentraci6n. Si se
siente inseguro en una cuesta, no la recorte. 19
HACER:
•Puede recortar atrav6s de la superflcle de
la cuasta, nunca hacla arrlba y hacla abajo.
Proceda con extrema precauck_)ncuando
camble de direccl6n en las cuestas.
Renueva todos los obJetosextranos, tales
como guijarros, ramas, etc.
Debe prastar atanci6n a hoyos, baches o
protuberanclas. Recuerde que la hlerba alta
puede esconder obstdculos.
NO HACER:
•No re,code cerca de pendlentes, zanjas o
terraplenas. El operador puede perder la
tracci6n en los pies o el equilibrio.
• No recorte cuestas demasiado inclinadas.
•No recorte en hierba mojada. La reduccl6n
en la tracci6n de la pisada puede causar
resbalones.
III. NINOS
Se pueden producir accidentes trdgicos si el
operador no presta atanci6n a la presencia
de los nifios. A rnenudo, los nitros se slenten
atrafdos por la mdquina y por la actJvidadde
la siega. Nunca suponga que los nifios van a
permanecer en el mismo lugar donde los vio
por dltJmavez.
•Mantenga a los nifios alejados del drea de
la siega y bajo el cuidado estricto de otra
persona adulta responsable.
•Est6 alerta y apague la mdquina si hay nifios
que entran al drea.
•Antes y cuando este retrocediendo, mire
hacia atrds y hacia abajo para verificar si hay
nifios pequefios.
•Nunca permitaque losnifiosoperen larndquina.
•Tanga un cuidado extra cuando se acorque
a esqulnas donde no hay visibilidad, a los
arbustos, drboles u otros objetos que pueden
interferir con su Ifnea de visi6n.
IV. SERVIClO
•Tenga cuidado extra al manejar la gasolina y
los demds combustibles. Son inflamables y
los gases son explosivos.
-Use solamente un envase aprobado.
-Nunca remueva la tapa del dep6sito de
gasolina o agregue combustible con el mo-
tor funcionando. Permita que el motor se
enfrfe antes de volver apone combustible.
No fume.
- Nunca vuelva a poner combustible en la
mdquina en recintos cerrados.
-Nunca almacene la mdquina o el envase
del combustible dentro de algL_nlugar en
donde haya una llama expuesta, tal como
la del calentador de agua.
Nunca haga funcionar una mdquina dentro
de un drea cerrada.
Nunca haga ajustes o reparaciones mientras
el motor est6 en marcha. Desconecte el
cable de la bujfa, y mant6ngalo a cierta
distancla de 6sta para prevenir un arranque
accidental.
Mantenga las tuercas y los pernos, espe-
cialmente los pernos del accesorio de la
cuchilla, apretados y mantenga el equipo en
buenas condiciones.

•Nunca manipule de forma indebida los
dispositivos de seguridad. Controle regular-
mante su funcionamlento corrects.
•Mantenga la mdquina fibre de hierba, hojas
u otras acumulaciones de desperdicio.
Limpie los derrames de aceite o combustible.
Permita que la mdquina se enfr|e antes de
almacenada.
•Pare e inspeccione el equips si Is pega a un
objeto. Repdrelo, si es necesado, antes de
hacerlo arrancar
•/n
•En nmgun caso hay que regular la altura de
las ruedas miantras el motor estd en marcha.
•Los componentes del receptor de la hJerba
van sujetos a desgaste, da_os y deterioro,
que pueden exponer las partes en mov-
imiento o permitlr que objetos seen dlspara-
dos. Controlar frecuantemente y cuando sea
necesado sustitulr con partes aconsejadas
por el fabricante.
•Las cuchillas de la segadora estdn afiladas y
pueden cortar. Cubdr las hojas o Ilevar guantes,
y utilizar precauciones especiales cuando se
efectda mantanimiento sobrs las mismas.
•No cambie el ajuste del regulador del motor
ni excsda su velocidad.
N_imem de Serie:
Fecha de Compra:
Capacidad y Tips de Gasolina: 1.6 Cuartos (Regular sin Plomo)
Tips de Aceite (API-SF-SJ): SAE 30 (Sobre 32°F); SAE 5W-30 (Debajo 32°F)
Capacidad de Aceite: 20 Onzas
Bujfa (Abertura: .030") Champion RJ19LM o J19LM
Torsi6n del Perno de la Cuchilla: 35-40 ft. Ibs.
El ndmerodelnodeloy el de seriese encuentranen la calcomaniaadjunta ala parts trasera
de la caja de lasegadora.Debe registrartantoel ndmerode seriecomela fecha de compray
mantengalos en un lugar seguropara refenciaen el futuro.
Acuerdos de Protecci6n pare la Reparaci6n
Congratulaciones por su buena compra. Su
nuevo products Craftsman_ estd disehado
y fabricado para funcionar de modo fiable por
muchos aSos. Pero corns todos los productos,
puede necesitar alguna reparaci6n de tanto
en tanto. En este caso tener un Acuerdo de
Protecci6n pare la Reparacibn puede hacerles
ahorrar diners y fastidios.
Compre ahora un Acuerdo de Protecci6n para
/a Reparaci6n y prot_gese de molestias y gas-
tos inesperados.
Un Acuerdo incluye los puntos siguientes:
•Servlcio experts de nuestros 12.000 espe-
cialistas profesionales en la reparaci6n.
• Servlcio illmitado sin cargo alguno para
las partes y la marts de obra sobre todas las
reparaciones garantizadas.
•Sustituci6n del products si su products
garanUzado no puede set arreglado.
•Descuentodel 10%sobreelpreciocor-
riente det servicio y de las partes relaUvas el
servicio no cubiertas por el acuerdo; tambidn
el 10% menos sobre el precis corriente de
un control de mantenimiento preventivo.
•Ayuda rdpida por tel6fono - soporte tele-
f6nico por parte de un t_cnico Sears sobre
productos que requieren un arreglo encasa,
y ademds una programaci6n sobre los a
reglos mds convenientes.
Cuando se ha comprado el Acuerdo, baste con
una Ilamada telef6nica pare programar el servi-
cio. Puede Ilamar cuando quiera, die y noche o
fijar en linea una cita pare obtener el servicio.
Sears tiene mds de 12.000 especialistas
profesionales en la repareci6n, que tienen
access a mds de 4.5 millones de partes y
accesorios de calidad. Este es el tips de
profesionalidad con que puede contar pare
ayudar a alargar la vida del products que acaba
de comprar, por muchos aSos. iCompre hoy su
Acuerdo de Protecci6n pare la Reparaci6nl
Se aplican algunas Ilmltaciones y exclu-
siones. Pare conocer los preolos y tener
mds informaci6n, Ilame al 1-800-827-6655.
Servicio de Instalaci6n Sears
Para la instalaci6n profesional Sears de
aparatos de case, puertas de garaje,
calentadores de agua y otros importantes
articulos para la casa, en U.S.A. Ilamar a
1-800-4-MY-HOME®,
2O

Estos accesodos estaban dlsponlbles cuando se produjo la segadom. No son facllltados Junto el
cortaceeped. Tambl0n estdn disponlbles en la mayoda de las tiendas de Sears y en los centros
de serviclo. Algunos de estos accesodos tal vez no se apliquen a su segadora.
RENDIMIENTO DE LA $EGADORA
DESlnADOR
DE RF.COR'I13
PARASEGADORAS
CONDESCARGA
TRASERA
RECOflEDOR
PARA
SEGADORAS
CONDESCARGA
TRASERA
MANTENIMIENTO DE LA SEGADORA
81LENCIADOREe
CORREA8 CUCHILLAS
ESrABIU-
ZADORE8
__ RECOREDOR
PAPA
SEGADORAS
CON DESCARGA
LA'I_RAL
FILTROS DE AIRE
ADAPTADORE8
DECUCHILLA RUEDAS ACEITE
DEL MOTOR
21