Craftsman 113.197250 User manual

fA
Save This Manual
For Future Reference
_ARS
Operators
Manual
MODEL NO.
113.197210
1O"ELECTRONIC
RADIAL SAW WITH
23" CABINET AND
1 DOOR
or
113.197250
10" ELECTRONIC
RADIAL SAW WITH
LEG SET
Serial
Number
Model and serial numbers
may be found at the rear of
the base.
You should record both
model and serial number in
a safe place for future use.
FOR YOUR
SAFETY:
READ ALL
INSTRUCTIONS
CAREFULLY
\\\\
113.197210
CRRFTSMRN
10-INCH ELECTRONIC
RADIAL SAW
• Assembly
• Operating
•Repair parts
Sold by SEARS, ROEBUCK AND CO., Chicago, IL. 60684 U.S.A.
Part No. SP5250 Printed in U.S.A.

FULLONEYEARWARRANTYONCRAFTSMANRADIALSAW
It wilhin one year Irom the dale o! purchase, this Craltsman Radial Saw fails due to a delect in material or
workmanship, Sears will repair it, free of charge.
WARRANTY SERVICE IS AVAILABLE BY SIMPLY CONTACTING THE NEAREST SEARS SERVICE
CENTER/DEPARTMENT THROUGHOUT THE UNITED STATES.
This warranly applies only while this product is used in the United States.
This warranty gives you specific legal rights and you may also have other rights which vary from state to state.
SEARS, ROEBUCK AND CO., DEPT. 698/731A Sears Tower, Chicago, IL 60684
Table of Contents
Section Title Page Numbers
Safety Information ............................................. 3-6
Putting Your Saw Together ...................................... 7-19
Location and Function of Controls ................................ 20-23
Alignment of Blade .......................................... 24-39
Digital Display .............................................. 40-45
Electrical Connections ......................................... 46-47
Crosscutting ............................................... 48-54
Ripping .................................................. 55-53
Cutting Accessories .......................................... 54-67
Recommended Accessories ....................................... 68
Lower Blade Guard Safety Information ............................... 59
Glossary .................................................... 70
Helpful Hints ............................................... 71-73
Maintaining Your Saw ........................................ 74-79
Trouble Shooting ............................................ 80-85
Parts Lists ................................................ 86-101

Safety Information
The operator's manual contains safety infor-
mation, instructions and signs for your protec-
tion against serious injuries, including:
Loss of fingers, hand, arm or leg from contact
with the saw blade.
Eye injuries, including being blinded from
being hit by a thrown workpiece, workpiece
chips or pieces of the saw blade.
Impact injuries, including broken bones and
internal organ damage, from being hit by a
thrown workpiece, workpiece chips or pieces
of the saw blade.
Shock, electrocution, or burn injuries from
contact with wires, motor or other saw parts.
Safety Symbol and Signal Words
The safety information in this manual is high-
lighted by the following safety alert symbol.
Fig. 1Safety Alert Symbol
The following signal words are used to indi-
cate the level of risk.
DANGER: Means that if the safety infor-
mation is not followed, someone will be
seriously injured or killed.
_1_ WARNING: Means that if the safety in-
formation is not followed someone could be
seriously injured or killed.
_lb CAUTION: Means that if the safety in-
formation is not followed someone may be in-
jured.
All of the safety information and cutting
steps are critical to the safe operation of the
radial arm saw.
Major Hazards
1. Workpiece Kickback
Kickback is an uncontrolled grabbing and
throwing of the workpiece during ripping. If
kickback occurs, the workpiece can hit
you hard enough to cause broken bones, in-
ternal organ injury or death. To reduce or
prevent kickback, read and follow the safety
information in the Ripping section of the
manual.
Kickback.
Internal injury can
result.
Use anti-kickback
pawls/spreader.
Fig 2 Kickback Safety Sign
2. Kickback Followed by Blade Contact
Kickback followed by blade contact can hap-
pen when the saw blade is pinched or bound
by the workpieee during ripping. Kickback
can happen if you reach around the blade to
the end with the anti-kickback pawls, (oat-
feed end), and try to hold-down or pull the
workpiece through to complete the cut. Your
fingers, hand, or arm can be cut off by the
blade if the workpiece kicks back.
Kickback, Blade
Contact.
Fingers, hand, arm
can be cut off.
Follow instructions
for Ripping
Fig. 3 Blade Contact Safety Sign

3. Wrong Way Feed
Wrong way feed is feeding the workpiece
into the end of the saw with the anti-kickback
pawls. The work_iece can be grabbed by the
blade and pull your hands into the blade
before you can let go or pull back. Fingers,
hand or arm can be cut off.
Fig. 4 Wrong Way Feed Safety Sign
If a workpiece is fed into the end of the saw
with the anti-kickback pawls, it can take off
like a missile. Anyone hit by the workpiece
can be killed. Feed the workpiece into the in-
feed end of the saw blade, the end that does
not have the anti-kickback pawls.
;'"- ..... I Wrong Way Feed.
_ O____ IWorkpiece impact
Feed into infeed
end of saw.
Fig. 5 Wrong Way Feed Safety Sign
4. Thrown Workpiece Chips and Blade
Pieces
The saw can throw the workpiece, workpiece
chips or pieces of the blade violently. You
can be blinded. Wear safety goggles labeled
"ANSI Z87.1" on the package.
A
can be blinded.
Wear safety
goggles.
Fig. 6 Safety Goggles Safety Sign
DANGER: Follow the 8 steps listed
below to reduce or eliminate the risk of
being injured when using the radial arm
saw. Failure to do so can result in a life
threatening injury or death.
_sscutting and ripping.
2. Set blade guard in horizontal position
when crosscutting.
3. Lower blade guard nose only when rip-
ping.
4. Keep hands as far away from the blade
as possible when cutting.
5. Return the saw to its rearmost position
after each crosscut.
6. Wait until the blade has stopped turn-
ing before reaching for the work?iece or
a_}thmg else on the table.
7. Read and follow the safety information
and safety instructions in the operator's
manual and in the safety labels on the
radial arm saw.
8. Know location and function of all con-
trois before using saw. See the Location
and Function of Controls section.

Personal Safety
1. Wear safety goggles labeled "ANSI Z87.1"
on the package. Do not wear regular glasses,
they are not safety glasses.
2. Wear snug fitting clothes, short sleeve
shirts and nonslip footwear. Cover up or tie
long hair. Do not wear loose, baggy clothes,
gleves, neckties, rings, watches or any other
jewelry.
3. Wear a dust mask, with your safety gog-
gles, if cutting operation is dusty.
4. Wear hearing protectors, ear plugs or
muffs, if you use the saw daily.
5. Keep good footing and balance. Don't over-
reach.
Work Area Safety
1. Keep children, pets and visitors out of the
work area.
2. Make the work area child proof. Remove
the yellow key from the red switch and place
it out of reach and sight. Lock work area.
3. Keep floors dry and free from sawdust, wax
or other slippery materials.
4. Keep work area clean, uncluttered and
well lighted.
5. Use the saw in a dry area. Do not use in
wet or damp area. Do not use outside.
6. Clear the table of all cbjects (adjusting
wrenches, tools, scraps of wood etc.) except
the workpiece to be cut, fixtures or clamps
before turning the saw on.
7. Do not do layout, assembly or setup work
on the table while the blade is turning.
8. Store items away from the saw. Do not
climb on the saw to reach items. Do not
stand on the table; the saw can tip over.
Saw Safety
1. Keep guards and anti-kickback pawls in
place and in working order.
2. Check for broken or damaged parts before
using saw. A damaged guard or other saw
part should be checked for alignment, bind-
ing, breakage and correct mounting to make
sure they are working properly. Repair or
replace damaged guards or other saw parts.
3. Unplug saw before doing maintenance,
making adjustments, and changing blades and
accessories.
4. Use clamps or vice to hold workpiece
when practical. It's safer than using your
hands and frees them to operate the saw.
5. Do not force the saw, saw blade or acces-
sories to do jobs they are not designed to do.
6. Make sure the yellow key is removed and
the red switch is in the off position before
plugging in the power cord.
7. Cut only wood, woodlike or plastic
materials. Do not cut metal materials.
8. Secure the saw to floor, wall, bench or
table if it slides, tips or walks during use.
9. Feed the workpiece against the direction
of rotation of the blade when ripping.
10. Turn the saw off before leaving work
area. Do not leave the saw until the blade
has stopped.
11. Lock the rip and miter locks before
moving the saw from one location to another.
12. Turn the saw off and remove yellow key if
the blade jams. Do not try to free a jammed
workpiece with the saw on.
13. Turn the saw off if it vibrates excessively
or makes an unfamiliar noise. Correct any
problems before restarting saw.

14. Rip workpieces that are longer than the
diameter of the blade being used. Do not rip
a workpiece that is shorter than the diameter
of the blade being used.
15. Cut only one workpiece at a time. Do
not cut stacked workpieces or lay them edge
to edge for cutting.
Workpiece Support Safety
1. Use additional supports for workpieces
which extend beyond the saw table. Large
workpieces can shift, twist, rise from table or
fall after they are cut.
2. Helpers can be hit by a thrown workpiece,
workpiece chips or pieces of the blade. Use
table extensions or other supports. Do not
use helpers.
3. ttelpers can cause the workpiece to kick-
back. Do not use other people to support or
assist in feeding or pulling the workpiece.
Use table extensions.
4. When table extensions over 24 inches wide
are added to either side of the saw, make
sure you either bolt the saw to the floor or
support the outer end of the extension from
the floor with sturdy legs or an outrigger.
5. Use Only Recommended Accessories
Follow the instructions that come with the
accessories.
Consult the owner's manual for recommended
accessories.
The use of improper accessories may cause
risk of injury to persons.
Blade Safety
1. Use blades marked for 3450 rpm or higher.
2. Do not use blades larger than 10 inches in
diameter.
3. Keep blade sharp and clean.
4. Do not cycle motor switch on and off rapid-
ly; the blade can loosen.
5. Do not overtighten the blade; the blade
collar can be warped.
Safety Labels on the Radial Arm Saw
The following labels are on your radial arm
saw. Locate, read and follow the safety in-
structions and information contained in these
labels.
1. Wrong way feed label located on the out-
feed end of the blade guard.
[DANGER
TO AVOID
INJURY DO NOT
FEED MATERIAL
INTO CUTTING
TOOL FROM
THIS END
Fig. 7Wrong Way Feed Label
2. Safety instruction label located on the
front of the saw near the handwheel.
[DANGER ]
FOR YOUR OWN SAFETY:
1. Read and understand owner's manual
before operating machine.
2. Wear safety goggles complying with
ANSI Z87.1.
3. Keep hands out of path of saw blade.
4, Never reach around the saw blade.
5. Never perform any operation
"FREEHAND:'
6. Return carriage to the full rear position
after each cross-cut type operation,
7. Shut off power and allow saw blade to
stop before adjusting or servicing
Fig, 8 Safety Instruction Label
3. Ripping safety label located on the motor.
[DANGER [WHEN RIPPING
1. R4t_ I_,d un_wl_l_l OWTNW'$ mlmuM S. Ule "PUSH STICK" fo_ rmrrow work
_g remcl_k,te. 7_ Nev_ orm tony ope_t}o,n
2. _1 _gl_ €omplying wh11 6. Nev_ flinch mrour_ th_ saw blade."FREt H_A_rl. "
3, Klmp hired= otlt of l_lth of sew b_. 8, Shut off power m_l allow IklW I_qKIll tO
4. Know hOW Io #_k:l _KICKBACKS? MOp before Kljusti_ Or _.rvi¢ing.
TO AVOID RUNAWAY WORKP!IECE
ALWAYS _WORXPIECE k_,to
cutting tool FT!OM TH_ B40 ONLY
DANGER AT OUTFEED
Workpi4bco c4_ smc_d4_W k_k _BCk
__ @pul h,t_do int oarKI und_ r.utU_l tool
MOtOr: 120Volts 11.0Ampl 3450 R.P.M. 60Hz. tPhase ModelC48HM'275
Fig. 9Ripping Safety Label

Putting Your Saw Together
Your radial arm saw is easy to put together,
however it will take time. Ask a friend to
help, and follow these assembly instructions.
It is important for your safety, and for the
quality of your cuts, that the saw be put
together with care.
This manual was written for two different
models of the radial arm saw: model
113.197210with cabinet and door, and model
113.197250 with leg set.
The following assembly sections should be
followed for both models:
Unpacking /Set up
Information
Attaching Handwheel
Mounting Motor
Mounting
Attaching
Mounting
Mounting
Saw'
Trim Ledge and Trim Caps
Table Locks
the Front Table
All other sections are labelled with the correct
model number. Follow ONLY instructions
that are meant for your model saw. Both
models work in the same way once they are
put together.
_1_ WARNING: Plugging the saw in
during assembly can result in electrical
shock or your fingers, hand, or arm be-
ing cut off from blade contact. Do not
plug in the saw at any time during as-
sembly. The saw should only be
plugged in when it is to be used.
Unpacking/Set up
Both Models
I As you unpack, try to keep the contents of
each of the smaller bags together and separate
from the others. This will help you identify and
locate the parts you need during assembly,
The following parts are included with model
113.197210:
A Basic Saw Assembly ............ l
B Rear Table .................... 1
C Table Spacer .................. 1
D Rip Fence ..................... 1
E Front Table .................... 1
F Operators Manual ............... 1
GLoose Parts Bag ................ 5
H Table Mounting, Channel ........ 2
I Trim Cap, R.H ................. 1
J Trim Cap, L.H ................. 1
K 23" Cabinet with Door .......... 1
G
I
Fig. 10 -Parts for Mode1113.197210

The following parts are included with model
113.197250:
ABasic Saw Assembly ............ 1
B Rear Table .................... 1
C Table Spacer .................. 1
D Rip Fence ...................... 1
E Front Table ................... 1
F Operators Manual .............. 1
G Loose Parts Bag ............... 5
H Table Mounting Channel ........ 2
I Trim Cap, R.H ................. 1
J Trim Cap, L.H ................. 1
K Leg .......................... 4
L Lower Stiffener ................ 4
M "U"-Channel .................. 1
B
MEDIUM SCREWDRIVER
7/16" WRENCH #2 PHILLIPS SCREWDRIVER
1/2" WRENCH
314" WRENCH
{_ HAMMER
314" SOCKET
9/16" SOCKET ::'::':_-" "-- -'--:_ ,
FRAMING SQUARE
PLIERS PENCIL
SOCKET WRENCH SOCKET EXTENSION 3/16" HEX "L" WRENCH
Fig. 12 - Tools Required
F
L
G
%.. _;| 1
Fig. 11 -Parts for Model 113.197250
2. Identify the large parts of your saw before
beginning each section. Your task will be
easier if you are familiar with these parts.
3. Identify the tools required for assembly.
Make sure that you have all of the tools you
wild need. (Figure 12)
4. Open the loose parts bags, and sort the
contents into piles on the floor or table. This
will make it easier for you to find the part(s)
you need during assembly.
The following loose parts are included with
model 113.197210:
AA Leveling Foot ................. 4
AB Hex Jam Nut 3/8-16 ............ 8
AC Truss Hd. Bolt 1/4-20 x 1/2 ..... 42
AD External Lockwasher 1/4 ....... 42
AE Hex Nut I/4-20 ............... 42
AA ,_ AD

AF Hex Hd. Screw 5/16-18 x 3/4 .... 4
AG Washer 11/32x 7/8x 1/16 ....... 4
AH Lockwasher 5/16 ............... 4
AI Hex Nut 5/16-18 ............... 4
AJ Pan Hd. Screw 1/4-20 x 1 ....... 4
AK Washer 17/64 x 5/8 x 1/32 ....... 5
AL Lockwasher 1/4 ................ 4
AM Hex Nut 1/4-20 ................ 4
AN Table Clamp .................... 2
AO Tee Nut ........................ 1
AP Cup Point Set Screw 1/4-20 x 7/8 .. 1
AQ Pan Hd. Screw Ty T
1/4-20 x 1-3/4 ................. 1
AR "U" Clip 1/4-20 ................. 1
AS Pan Hd. Screw #6-10 x 1/2 ........ 2
AT Pan Hd. Screw Ty "T" 6-32 x 3/8 . 2
AU Pan Hd. Screw #10-10 x 1/2 ....... 4
AV Magnetic Catch ................. 1
AW Door Hinge ..................... 2
AX Yoke Plug ...................... 1
AY Switch Key ..................... 1
AZ Battery ......................... 1
BA Pan Hd. Screw 10-32 x 1/2 ........ 1
BB Battery Cover ................... 1
BC External Lockwasher #10 ......... 1
BD Handwheel ..................... 1
BE Arbor Wrenches ................. 2
BF Casters ............................ 2
BG Hex Bushing ....................... 1
AF
A3
( AK
(3_ AT
Au
Az
BB
©BC
8F

The following loose parts are included with
model 113.197250: BX CD
BG Leveling Feet .................... 4
BH Hex Nuts 3/8-16 ................. 8
BJ Truss Head Bolts 1/4-20 x 1/2 .... 32
BK Lockwashers 1/4 ................ 32
BL Hex Nuts 1/4-20 ................ 32
BM Hex Hd. Screw 5/16-18 x 3/4 ...... 4
BN Washer 11/32 x 7/8 x 1/16 ........ 4
BO Lockwasher 5/16 ................ 4
BP Hex Nut 5/16-18 ................. 4
BQ Pan Hd. Screw 1/4-20 x 1 ......... 4
BR Washer 17/64 x 5/8 x 1/32 ........ 5
BS Lockwasher 1/4 ................. 4
BT Hex Nut 1/4-20 .................. 4
BU Table Clamp .................... 2
BV Tee Nut ........................ 1
BW Cup Point Set Screw 1/4-20 x 7/8 .. 1
BX Pan Hd. Screw Ty T
1/4-20 x 1-3/4 ................. 1
BY "U" Clip 1/4-20 ................ 1
BZ Yoke Plug ...................... 1
CA Switch Key ..................... 1
CB Battery ......................... 1
CC Pan Hd. Screw 10-32 x 1/2 ........ 1
CD External Lockwasher #10 ......... 1
CE BatteD' Cover ................... 1
CF Handwheel ..................... 1
CG Arbor Wrench .................. 2
CH Bracket, Leg ....................... 4
CI Hex Bushing ....................... 1
BG
10
BY CE
CG
CB
cc CH
Information
BOTH MODELS Cl
1. If you are missing any part while putting
your saw together, do not continue assembly.
Contact your Sears Service Center or Retail
Store and get the missing part before continu-
ing assembly or trying to use the saw.
Complete parts lists are located at the end of
this manual. Use these lists to identify the
number of any missing part.
2. Sometimes small parts get lost in packag-
ing materials. Do not throw away any pack-
aging until your saw is put together. If you
are missing a part, check the packaging be-
fore contacting Sears.
3. Most parts of your radial arm saw will be
fastened together using truss head bolts, lock-
washers, and hex nuts of the sizes shown.
(Figure 13) When different sizes are needed,
the instructions will include a sketch to help
you locate the correct size.
Fig. t3 -Truss Head Bolt, Lockwasher, Hex Nut

4. As you assemble your radial arm saw,
some of the holes in the parts will line up and
others will not. This happens because some
parts are used in other equipment or for other
purposes. Follow the instructions carefully.
The figures will show which holes should line
up in each step.
Attaching Handwheei
BOTH MODELS
1. Locate the handwheel, hex bushing, screw,
and lockwasher.
1. Loosen the guard clamp screw and
remove the guard from the motor.
2. Use the arbor wrenches to remove the
blade from the saw. The arbor shaft has left-
handed threads, so you will have to turn the
nut clockwise to loosen.
3. Lock the rip lock.
4. Turn the handwheel in a clockwise direction
to raise the radial arm about 2 inches and
remove the styrofoam packing blocks.
5. Clean the small pieces of styrofoam off
the saw.
2. Place the hex bushing inside the handwheel.
3. The hex bushing has a small flat area on it
which matches a flat area on the elevation
shaft.
4. Align the two above flat areas and attach
the handwheel using a screw and lockwasher.
Handwheel
Rg. 13A
Sm©©
Fig. 13B -Screw, External Lockwasher and Hex
Bushing Mounting the Motor
BOTH MODELS
_Ib'WARNING: Plugging the saw in
during assembly can result in electrical
shock or your fingers, hand, or arm
being cut off from blade contact. Do
not plug in the saw at any time during
assembly. The saw should only be
plugged in when it is to be used.
6. Place the motor on the center channel of
the saw and remove the three table boards
and fence.
7. Remove the lock nut and flat washer from
the motorpivot support. (Figure 13C)
Motor Pivot )_)_-__i, JP""-_L "- /f! I
Fig. 13C
8. Slide the bevel encoder to the top center
position so it will fit into the notch on the
motor support bracket. (Figure 13C)
9. Slide the motor onto the motor pivot sup-
port. Make sure the motor is firmly in place.
10. Put the flat washer and locknut back in
place and tighten using a 3/4 inch socket
wrench. Move the bevel lock back and forth
as you tighten the locknut. Do not over-
tighten.
11

11. Push the bevel lock to the left as far as it
will go. (Figure 13D)
12. If there is a 1/16 inch gap or less between
the bevel lock and the left side of the yoke
(and they are not touching), go to step 14, or
Bevel Lock
A Right Side Panel ............... 1
B Left Side Panel ................ 1
C Lower Shelf ................... 1
D Skirt ......................... 2
E Shelf Stiffener ................. 1
F Corner Bracket ................ 2
G Spacer ....................... 2
H Door ......................... 1
I Caster ........................ 2
D
FTg.13D
If the bevel lock touches the left side of the
yoke, unlock the bevel lock and tighten the
locknut on the motor pivot support. Then go
to step 10 and repeat, or
If there is more than 1/16 inch gap between
the bevel lock and the left side of the yoke,
unlock the bevel lock and loosen the locknut
on the motor pivot support. Then go to step
10 and repeat.
13. Repeat steps 10-11 until the bevel lock will
not touch the left side of the yoke, and the gap
is not more than 1/16 inch.
14. I._k the bevel lock.
15. Snap the yoke plug into place. The yoke
plug is in the loose parts bag.
Beginning the Cabinet
MODEL 113.197210
The following parts are used in the cabinet
assembly for model 113.197210:
F G
Fig. 14-Cabinet Assembly -113.197210
1. Turn the shelf upside down on the floor.
The wide edge should point down, and the
three narrow edges should point up.
(Figure 15)
0000
00 0 o
Shelf
Corner
Brackets ._
o
o
Fig. 15
2. Put a corner bracket in the front corners of
the shelf. (Figure 15)
12

3. Put two truss head bolls through the shelf
and each corner bracket to hold the brackets
in place•
4. Put a lockwasher and hex nut on each bolt
and tighten with a 7/16 inch wrench or
socket.
5. Put the shelf stiffener on the shelf and line
up the holes. (Figure 16)
Shelf Stiffener
Fig. 17
9. Turn the right side panel so that the J-
shaped slot is at the bottom and facing you.
10. Put a spacer inside the right side panel as
shown. The side of the spacer with two round
holes should be opposite the J-shaped slot in
the side panel, and the side with one larger
hole should be on the bottom. (Figure 18)
Fig. 16
Truss Head Bolt
--_ Lockwasher
Hex Nut
6. Put the casters (wheels) on the shelf and
shelf stiffener. Since the shelf is upside down,
the wheels will point up. Line up four holes
on each side. (Figure 16)
7. Put truss head bolts through the holes on
each side. Put a lockwasher and hex nut on
each bolt and tighten using a 7/16 inch
wrench or socket.
Spacer
_und_H_ i)
One Larger Hole
Fig. 18
Right Side Panel
-Shaped Slot
11. Put two truss head bolts through right
side panel and spacer, one on each side.
12. Put a lockwasher and hex nut on each
bolt and tighten using a 7/16 inch wrench or
socket.
8. Find the right and left side panels. Look
carefully to find the "R" and "L" stamped
in the metal near the center of the wide edge.
These stamps are the easiest way to tell the
right side panel from the left. (Figure ! 7 )
13. Put aplastic cover over the J-shaped slot
in the side panel. (Figure 18)
14. Repeat steps 9-13 with the left side
panel.
13

15. Attach two hinges to the right side panel
above the spacer, using four truss head bolts,
lockwashers, and hex nuts. Tighten with a
7/16 inch wrench. (Figure 19)
Fig. !9
Spacer
.,..----Right Side
Panel
16. Lay the shelf on the rear edge with the
bottom side toward you. The angled end of
the lower support should point up.
17. Place the right side panel on the right
side of the shelf. The _pacer should be on the
inside of the cabinet. (Figure 20)
Corner Brackets
18. Put truss head bolts through the three
holes along the bottom edge of the right side
panel. Put a lockwasher and hex nut on each
bolt and tighten using a 7/16 inch wrench or
socket. (Figure 20)
Note: It is sometimes difficult to get bolts
through these three holes. You may need to
use a Phillips screwdriver to help shift the
parts into place.
19. Repeat steps 17-18 with the left side
panel and the left side of the shelJ:
20. Turn the cabinet right side up. Attach the
skirts to the top of the side panels, with one
on the front of the cabinet and the other on
the back. (Figure 21)
Rear Skirt
ht Side Panel
\\
\\
Left Side
Panel
Fig. 21
Shelf
Front
Skirt
Shelf
Shelf Stiffener -_ Right Side
Panel
Rear Flange "_
Fig. 20
21. Use eight truss head bolts, lockwashers,
and hex nuts to hold the skirts in place. Hand-
tighten. (Figure 21)
22. Put a truss head bolt through the hole at
the back, right corner of the shelf. This hole
goes through the shelf and the right side
panel. (Figure22)

Rear Right Side Panel
Shelf
Front
Fig. 22
23. Put a lockwasher and hex nut on the bolt
and tighten using a 7/16 inch wrench or
socket.
24. Repeat steps 22-23 on the left side of the
shelf.
25. Put a truss head bolt through the back of
the right spacer and front edge of the shelf.
(Figure 23)
O
o )
Side Panel
Fig. 23
Shelf
Spacer 1
I
26. Put a lockwasher and hex nut on the bolt
and tighten using a 7/16 inch wrench or
socket.
27. Repeat steps 25-26 with the left spacer.
28. Move the cabinet to the location where
you will use your saw.
29. Put a hex nut on each of the leveling feet.
(Figure 24)
Fig. 24 - Hex Nut for Leveling Foot
30. Put the leveling feet through the holes in
the bottom of the side panels, at the four
corners of the shelf.
31. Put another hex nut on each of the
leveling feet and hand-tighten until they are
against the side panels.
_lb WARNING: Saw blade can roll for-
ward toward you if the leveling feet are
not correctly adjusted. Workpiece or
saw can move unexpectedly if cabinet
rocks. Fingers, hand, or arm can be cut
off from blade contact. Adjust leveling
feet before using your saw.
32. If the leveling feet raise the front of the
saw slightly higher than the rear, and if the
cabinet does not rock, go to step 38, or
If the leveling feet do not raise the front of
the saw slightly higher than the rear, go to
step 33, or
If the cabinet rocks, go to step 33.
33. Loosen the bottom hex nut on the desired
leveling foot using a 9/16 inch wrench.
34. Loosen the top nut by hand.
15

35. Adjust the lower nut with the 9/16 inch
wrench until the levelingJoot is at the desired
height.
36. Tighten the top nut by hand.
37. Repeat steps 33-36 for the other three
leveling feet if necessary.
38. Tighten all four bottom nuts using a 9/16
inch wrench.
Attaching Door
Fig. 27 -Pan Head Screw
3. Attach the door to the hinges on the side
panel using four plastite screws. Tighten with
a Phillips screwdriver. (Figure 28)
Magnetic Catch
/
Magnetic Stop Plate
Fig, 25 -Parts for Door Assembly
1. Put a magnetic catch on the inside edge of
the door. (Figure26)
2. Fasten using two pan head screws. Tighten
with a Phillips screwdriver. (Figure 26 & 27 )
Door
/
1
d
Magnetic Catch
Fig. 28 -Plastite Screw
4. Attach a magnetic stop plate to the two
small holes on the side of the front support
using four pan head screws. Tighten with a
Phillips screwdriver. (Figures 29 & 30)
Front Support o
o
-4-- Magnetic Stop Plate
Pan Head Screw
Fig. 29
Fig. 30 -Pan Head Screw
Fig. 26
16 /

Mounting the Saw to Cabinet
1. Hold the saw by the front edge and the
back of the column support, and lift it onto
the cabinet. It may be necessary to have
someone help you lift the saw. Make sure that
four holes in the bottom of the saw line up
with four holes in the top of the cabinet.
2. Fasten the saw to the cabinet with four
truss head bolts. Put a lockwasher and hex nut
on each bolt and tighten using a 7/16 inch
wrench or socket.
0_igure 31)
Fig. 32 -SupportBracket, LevelingFoot
Leg
_ Support Bracket
Fig. 33
Truss Head Bolt
saw II
Cabine__jj
kockwasher-_
Hex Nut
,-1o,
[Cabinet [
?(Top View)_
,%
2. Put ahex nut on each of the levering feet.
Put the levering feet through the holes in the
bottom of the J7oor leveler support bracket.
3. Put another hex nut on each of the leverng
feet and hand-tighten until they are against the
leg.
Fig. 31
3. Check all the nuts holding the cabinet
together and tighten them using a 7/16 inch
wrench or socket.
Attaching the Leg Set
MODEL 113.197250
1. Mount floor leveler support brackets inside
legs. Line up the three tabs on brackets with
slot on leg and tap into place. Make sure lip
on bracket points up. (Figure 33)
Install the remaining three brackets the same
way.
Leg
Support Bracket
Fig. 34
Nuts
_Leveling Foot
17

Building the LEG SET
The following parts are used in the leg set
assembly:
A Legs .......................... 4
B Lower Stiffeners ................ 4
A
B
BA
/A
Fig. 35 -Leg Set
1.' Lay a piece of cardboard on the floor to
keep from scratching the saw.
2. Position the basic saw assembly on the
floor as shown below. The arm assembly
should be pointing up in a vertical position
and the column support cover should be
resting flat on the floor. It may be necessary to
have someone help you lift the saw.
Sw_tch Front
_Front Legs Are
Ill A.aohed.ero
_1 hr---f'_l LI// \ Rear Legs Are
L4[_-%-L_Attached Here
Column Support
Cover
Fig. 36
3. Use truss head bolts, lockwashers, and nuts
(see Fig. 12) to mount the two rear legs to the
basicsaw assembly. Make sure that the four
holes in each corner of the saw line up with
four holes in the top of each leg. Finger
tighten nuts at this time.
4. Mount the two front legs to the basic saw
assembly using truss head bolts, lockwashers,
and nuts. However only put bolts through the
sides of the saw assembly not the front.
Fig. 37 -Bolt, External Lockwasher,
Hex Nut, U-Channel
Nut and
Lockwasher
1\
Channel
Leg
!
L--...
Truss Head Screw
Fig. 38
5. Position the front channelpiece inside the
legset. (Figure 38) Fasten the channelpiece,
leg, and saw together with two truss head
bolts on each side. Put a lockwasher and hex
nut on each bolt. The threaded section of the
bolt should point towards the arm assembly.
18

Truss Head _*_
Bolt
Fig. 39
6. Attach the four (4) lower stiffeners to the
legs. Two (2) truss head bolts, washers, and
nuts are required to hold each end of a lower
stiffener in place. Hand tighten hex nuts.
7. Go back with a 7/16 wrench or socket and
tighten all hex nuts.
8. Carefully lift the saw into its normal
position. It will be necessary to have someone
help you in order to avoid damaging the saw.
Adjusting Leveling Feet
_Ib WARNING: Saw blade can roll
forward toward you if the leveling feet are
not correctly adjusted. Workpiece or saw
can move unexpectedly if cabinet rocks.
Fingers, hand, or arm can be cut off from
blade contact. Adjust leveling feet before
using your saw.
1. If the leveling feet raise the front of the saw
slightly higher than the rear, and if the leg set
does not rock, go to step 13, or
If the leveling feet do not raise the front of the
saw slightly higher than the rear, go to step 8,
or
If the leg set rocks, go to step 8.
2. Loosen the bottom hex nut on the desired
leveling foot using a 9/16 inch wrench.
3. Loosen the top nut by hand.
4. Adjust the lower nut with the 9/16 inch
wrench until the leveling foot is at the desired
height.
5. Tighten the top nut by hand.
6. Repeat steps 8-11for the other three
leveling feet if necessary.
7. Tighten all four bottom nuts using a 9/16
inch wrench.
Attaching Trim Caps
BOTH MODELS
1. Find the left and right trim caps.
2. There are two plastic stubs on the back of
each trim cap.
3. These stubs will snap into matching holes
at the front corners of the saw.
4. Snap the left and right trim caps into place.
19

Location and Function of Controls
i
) i
iii! i
113.197210
Fig. 45 -Radial Saw Controls
On/Off Switch
The on/off switch turns the power to the saw
on and off.
To turn the saw on, put the yellow key into
the red xwitch and then pull the switch to the
right. To turn the saw off. push the red switch
to the left. Remove the yellow key from the
red switch whenever the saw is turned off,
and keep it out of the reach and sight of
children. (Figure 46)
Fig. 46 -On/Off Switch
113.197250
_1_ WARNING: The saw can start ac-
cidentally or be used by children and
others when the yellow key is left in the
red switch. Always remove the yellow
key when the saw is off, and keep it out
of the reach and sight of children.
WARNING: The saw will start im-
mediately when the power comes back
on after a blackout if the red switch is
left on. Always turn the switch off and
remove the yellow key when the power
goes off for any reason.
Miter Lock
The miter lock is used to hold the radial arm
at various angles to the fence.
To unlock the miter lock, pull the lock to the
right. (Figure 47)
2O