Craftsman 247.885550 User manual

E'S
MANUAL
MODELNOS.
247.885550
247.885680
Caution:
ReadandFollow
AllSafetyRules
andInstructions
BeforeOperating
ThisEquipment
5 AND 8 HORSEPOWER
24" AND 26" WIDTH
TWO STAGE
TRACK DRIVE
SNOW THROWERS
Assembly
Operation
CustomerResponsibilities
ServiceandAdjustment
RepairParts
®

n,,,,,,,.............. iim ' u='=,''= i=,=1=11 i =,,n=H,......................
SAFETY RULES
ii =i,,m == ................... ,,1=_== m
WARNING: TO REDUCE THE POTENTIAL FOR ANY INJURY, COMPLY WITH THE FOLLOWING
SAFETY INSTRUCTIONS. FAILURE TO COMPLY WITH THE INSTRUCTIONS MAY RESULT IN
PERSONAL INJURY.
_b TRAINING • Stopenginewheneveryouleavethe operatingposition,before
• Readthisowner'sguidecarefullyin its entiretybeforeattempting uncloggingthe collectorlimpelierhousingor dischargeguide,
toassembleor operatethis machine.Becompletelyfamiliarwith andmakinganyrepairs,adustments,orinspectionsNeverplace
thecontrolsandtheproperuseof this machinebeforeoperating your hand n the dschargeor co ector openngs Usea stick or
it. Keepthis manualin a safeplacefor futureandregularrefer- woodenbroomhandleto unclogthedischargeopening
onceandfor orderingreplacementparts. *Takeall possibleprecautionswhenleavingtheunit unattended
e Neverallowchildrenunder14yearsoldto operateasnowthrow- Disengagethe collectodimpeller, shift into neutral, stop the
er Children14 years old and overshouldonlyoperatesnow engine,andremovethekey
thrower under close parentalsupervision Only personswell • When cfeaning, repairing, or inspecting, make certain
acquaintedwith theserulesof safeoperationshouldbe allowed collectodimpellerandaflmovingpartshavestopped Disconnect
to useyoursnowthrower, sparkplugwire andkeepawayfrom plug to preventaccidental
• Nooneshouldoperatethis unitwhileintoxicatedor whiletaking starting.
medicationthat impairsthesensesor reactions o Do not run engineindoors, exceptwhen starting engineand
°Keeptheareaof operationclearof all persons,especiallysmall transportingsnowthrower in or out of building Opendoors
childrenandpets Exhaustfumesaredangerous.
o Exercisecaution to avoidslipping or falling, especiallywhen o Donot clearsnowacrossthefaceof slope&Exerciseextreme
operatinginreverse cautionwhenchangingdirectionon slopes.Do notattempt to
_ PREPARATION clearsteepslopes.
o Thoroughlyinspecttheareawheretheequipmentis to beused • Neveroperatesnow thrower without guards, plates,or other
andremovealtdoormats,sleds,boards,wires andotherforeign safetyprotectiondevicesin ptace
objects • Neveroperatesnow throwerneargtassenclosure,automobiles,
•Disengageall clutches and shift into neutratbefore starting windowwells,dropoff,etc, withoutproperadjustmentsof snow
engine throwerdischargeangle.Keepchildrenandpetsaway
= Donotoperateequipmentwithoutwearingadequatewinterouter = Donot overloadmachinecapacitybyattemptingto ciearsnowat
garments.Donotwearjewelry,longscarfsor otherloosecloth- toofastarate.
ing which could become entangled in moving parts Wear o Neveroperatethemachineat hightransportspeedson slippery
footwearwhichwill improvetootingonslipperysurfaces surfacesLookbehindandusecarewhenbacking
= Beforeworkingwith gasoline,extinguishall cigarettesandother '_ Neverdirectdischargeat bystandersor allowanyonein front of
unit.
sourcesof ignition Checkthe fuel beforestartingthe engine
Gasolineisan extremelyflammablefuel. Donotfill thegasoline • Disengagepowerto collector/impellerwhentransportingor not
tank indoors,while the engineis running,or untit enginehas inuse.
beenatlowedto coo!atleasttwo minutes Replacegasolinecap ° Useonlyattachmentsandaccessoriesapprovedbythemanufac-
securelyandwipe off anyspilledgasolinebeforestarting the lurer of snowthrower(suchaswheelweights,counterweights,
engineasitmaycauseafireorexplosion cabs,etc..).
•Usea groundedthreewireplug-infor al!unitswith electricdrive = Neveroperatethesnow throwerwithoutgoodvisibility or light.
motorsorelectricstartingmotors. Alwaysbesureof yourfootingandkeepa firm holdon thehan-
g Adjustcollectorhousingheightto cleargravelor crushedrock dies.Walk,neverrun.
surface • Mufflerand enginebecomehot and cancausea burn. Do not
= Neverattemptto makeanyadjustmentswhileengineis running touch
(exceptwherespecificallyrecommendedbymanufacturer),
• Letengineand machineadjustto outdoortemperaturebefore
startingtoclearsnow
o Alwayswearsafetyglassesor eyeshieldsduring operationor
whileperformingan adustmentor repair,to protecteyesfrom
foreign objectsthat may be thrown from the machinein any
direction
_OPERATION
8 Donot puthandsor feetnearorunderrotatingparts Keepclear
ofdischargeopeningandaugeratalltimes
° Exerciseextremecautionwhenoperatingon or crossinggravel
drives,walks,or roads.Stayalertfor hiddenhazardsor traffic..
Donotcarrypassengers.
• Afterstrikinga foreignobject,stoptheengine,removewirefrom
spark plug,and thoroughly inspectthe snow thrower for any
damageRepairthedamagebeforerestartingand operatingthe
snowthrower
•If thesnowthrowershouldstartto vibrateabnormally,stopthe
engineandcheckimmediatelyforthecauseVibrationisgeneral-
lyawarningof trouble.
MAINTENANCEANDSTORAGE
*Checkshearbolts,enginemountingbolts,etc.,atfrequentinter-
valsfor propertightnesstobe sureequipmentis in safeworking
condition.
o Neverstorethemachinewith fuelin the fueltankinsidea build_
ing whereignitionsourcesare present,such as hot waterand
spaceheaters,clothesdryers,andthe like Allowengineto cooi
beforestoringin anyenclosure
o Alwaysreferto owner'sguideinstructionsfor importantdetailsif
snowthroweristo bestoredforanextendedperiod
= Run machinea few minutes after throwing snow to prevent
freezeupofcollector/impeller
*Checkdutch controlsperiodicaliyto verifythey engageanddis-
engageproperlyand readjust if necessary Referto owner's
guideforadjustmentinstructions
LOOK FOR THIS SYMBOL TO POINT OUT
IMPORTANT SAFETY PRECAUTIONS, IT
MEANSmATTENTION!!! BECOME ALERT!!!
YOUR SAFETY tS INVOLVED.

CONGRATULATIONS on your purchase of a Sears
Craftsman snow thrower It has been designed, engineered
and manufactured to give you the best possible dependabil-
ity and performance,
Should you experience any problem you cannot easily rem-
edy, please contact your nearest Sears Service Center/
Department in the United States. We have competent, well-
trained technicians and the proper tools to service or repair
this unit
Please read and retain this manual The instructions wilt
enable you to assemble and maintain your snow thrower
properly Always observe the "SAFETY RULES,"
MODEL
NUMBER
SERIAL
NUMBER
DATE OF
PURCHASE
THE MODEL AND SERIAL NUMBERS WILL BE FOUND
ON A LABEL ATTACHED TO THE FRAME OF THE
SNOW THROWER,
YOU SHOULD RECORD BOTH SERIAL NUMBER AND
DATE OF PURCHASE AND KEEP 1N A SAFE PLACE
FOR FUTURE REFERENCE
CUSTOMER RESPONSIBILITIES
eRead and observe the safety rules,
®Follow a regular schedule in maintaining, caring for
and using your snow thrower.
e Follow the instructions under"Customer
Responsibilities" and "Storage" sections of this
Owner's Manual
PRODUCT SPECIFICATIONS
Horsepower: 50 &0
Displacement: 1353 cu, in. 19,43 cu, in
Fuel Capacity: 2 Qts. 1 Gal°
(Unleaded) (Unleaded)
Spark Plug J-SC or J-SC or
(Gap .030 in.): Equivalent Equivalent
Ignition Air Gap: .0125" ..0125"
MAINTENANCE AGREEMENT
A Sears Maintenance Agreement is available on this
product. Contact your nearest Sears store for details
WARNING: This unit is equipped with an internal combus-
tion engine and should not be used on or near any unim-
proved forest-covered, brush-covered or grass-covered land
unless the engine's exhaust system is equipped with a
spark arrester meeting applicable local or state laws (if any)
If a spark arrester is used, it should be maintained in effec-
tive working order by the operator
In the State of California the above is required by law
(Section 4442 of the California Public Resources Code)
Other states may have similar laws Federal laws apply on
federal lands, A spark arrester for the muffler is available
through your nearest Sears Authorized Service Center,
(See the REPAIR PARTS section of this manual,)
ONEYEAR LIMITED WARRANTYONCRAFTSMANGASSNOW THROWER
For one year from the date of purchase, when this Craftsman Snow Thrower is maintained, lubricated and
tuned up according to the instructions in the owner's manual, Sears will repair, free of charge, any defect in
material and workmanship.
If this Craftsman snow thrower is used for commercial or rental purposes, this warranty applies for only 30 days
from the date of purchase.
This warranty does not cover:
• Expendable items which become worn during normal use, such as skid shoes, shave plate and spark plugs.
• Repairs necessary because of operator abuse or negligence, including bent crankshafts and the failure to
maintain the equipment according to the instructions contained in the owner's manual..
WARRANTY SERVICE IS AVAILABLE BY RETURNING THE CRAFTSMAN SNOW THROWER TO THE
NEAREST SEARS SERVICE CENTER/DEPARTMENT IN THE UNITED STATES THIS WARRANTY
APPLIES ONLY WHILE THIS PRODUCT IS IN USE IN THE UNITED STATES..
This warranty gives you specific legal rights, and you may also have other rights which may vary from state to
state
SEARS, ROEBUCK AND CO., D/817WA, Hoffman Estates, IL 60179

,llji _, .................... iii, Ul,,i,iiiiiiiii Hill
SAFETY RULES ............................................................................ 2
PRODUCT SPECIFICATIONS ............................................3
WARRANTY ............................................................................. 3
INDEX ..............................................................................................4
ASSEMBLY INSTRUCTIONS .................................................5
OPERATION .............................................................................10
CUSTOMER RESPONSIBILITIES ................................. 15
ii ...................... i i U,l,lllllil,,,ii i Ul,ii ..............................
TABLE OF CONTENTS
iii i,u, iii i,, M I"III'H '1111'
STORAGE ..................................................................................17
SERVICE AND ADJUSTMENT .........................................17
TROUBLE SHOOTING ..........................................................21
REPAIR PARTS--SNOW THROWER ..........................22
REPAIR PARTS--ENGINE ..................................................31
PARTS ORDERING/SERVICE ..................BACK COVER
.................... iii .... i ii1,.,...................... ii, i ,, ,i,ir,llr11, ii, i i , i,i1,111 ii i, I
INDEX
i r iii1,11,,,i,1,,i,i ,,111111 , Ul,Ull iii1,1, ,
A
Adjustments:
Auger Clutch ................................................................................. 20
Carburetor ................................................................ 20
Shift Rod ......................................................................................g, 20
Skid Shoes ................................................................... 9, 17
Traction Drive Clutch ................................................................9, 19
Assembly Instructions:
Chute .............................................................................................................6
Chute Crank ........................................................................... 7
Clutch Cables ................................................................................... 8
Final Adjustments .................................................................. 9
Handle .........................................................................................6
Hardware Pack ................................................................................5
Shift Rod ....................................................................................8
Track Controls .....................................................................................8
C
Controls .........................................................................................t 0-11
Customer Responsibilities ............................................... 15
E
Engine:
Lubrication................................................................................... t3, 16
Maintenance ..................................................................... 16
Starting ...............................................................................................14
Stopping ................................................................................. 12
Storage ........................................................................................... 17
i1,,1111111i, i,,irr i lUI'M' lU"IIII
F
Fuel .......................................................................................................13
L
Lubrication ............................................................................... 15
M
Maintenance:
Agreement .............................................................................................. 3
Schedule ......................................................................................15
Engine .................................................................................... 16
O
Oil ........................................................................................ 13, 16
Operating Tips .....................................................................................t5
R
RepaidReplacement Parts ...............................................................20
Responsibilities, Customer .................................................... 3
S
Safety Rules .................................................................................. 2
Spark Plug ....................................................................................... 16
Specifications ................................................................................................ 3
Storage ........................................................................................17
T
Table of Contents ................................................................. 4
W
Warranty ...................................................................................... 3
| u .................................................... ,,Jill iii ,11,1111
SNOW THROWER ACCESSORIES
i iiiql ,11, 1,1,1,11 ,, =, i iii1,11111111................... iiil,,,lU,lUl,, i n,,lll I II
These accessories were available when the snow thrower was purchased. They are also available at most Sears
retail outlets, catalog and service centers. Most Sears stores can order repair parts for you, when you provide the
model number of your snow thrower,.
ENGINE
Two Cycle Oil Gas Can Spark Plug
SNOW THROWER MAINTENANCE
Scraper Bar Belt

ASSEMBLY INSTRUCTiONs ..................................
i i,,i iii IIIHII II IIIIIII1,111,111,11,1 111111,
IMPORTANT: This unit has been shipped WITH- Tools Required for Assembly:
OUT GASOLINE or OIL, After assembly, see oper- 1/2" Wrench*
ation section of this manual for proper fuel and (2) 7/16" Wrenches*
engine oil recommendations. Pair of Pliers
*or Adjustable Wrenches
NOTE: To determine right and left hand sides of your
snow thrower, stand behind it in the normal operating Loose Parts in Carton:
position° (t) Handle Panel and Chute Assembly
TO REMOVESNOW THROWER FROM CARTON (attached by cable)
Cut the corners of the carton, Remove all packing (1) Right Hand Handle
inserts. Roll snow thrower out of the carton, Make (1) Left Hand HandJe
certain all parts and literature have been removed (1) Chute Crank Assembly
before the carton is discarded. (1) Shift Rod
CONTENTSOFHARDWAREPACK
Lay out the hardware according to the illustration for identification purposes, Part numbers are shown in
parentheses
_ATTACHING THE HANDLE ASSEMBLY
Hex Bolts {]CZ0(_ZZ0
5t16-18 x %3/4" _
_/_ Hex Nuts" L_ _
_V_J_.--1/4-20 Thread_
(736-0287) _-_
_Rex Bolts
_"--- 5/16-18 X518"
_Long (710-0538} Handle Tabs
(784-5599}
(_-_ Lock Cupped
'_J_.--Washers
_ 5t16" I,D, (735-0270)Washers*[..-.\'_vJ
(736-011 g) 114" I.D,"-'-"_
Hex Bolts* _LJjJ
1/4-20 x v
1Bolts_
5116:18x [] l_J
1-1/2 Long _
(710-12S0) _ @
Cupped Washers*_-._(F'_
51t6' I,D.
(736-0242)
HeX Nuts*
5116-18 Thread (712-0267)-=.O _ _
*May be preassembled on your unit.
_ATTACHING THE CHUTE CRANK
Flat Washers
3t8" LD, x 5/8" O.D, Hex Bolt tT-17,7_
5f16-18 x 1-1t2"
Long
(710-0442} _
Lock Washer
T5/16" LD, _'t'_
(736-011_)
Hex Nut
Cotter Pin 5116-18 Thread----_{'C)]
(714-0507) (712-0267)
B_ ATTACHING THE CHUTE ASSEMBLY
Hex Bolts
114-20 x 314" Long
(710-3015)
_)(_7,('_ Hex Lock Nuts
"=" _'-_ 1/4-20 Thread
"- Chute Range
Keepers
(731-0851 )
D_ ATTACHING THE..SHIFT ROD
AND CLUTCH CABLES
E_ AUGER SHEAR BOLTS tT"'-f7 ri-'77
The _ug_rs_re securedto the spiral shaftw_h _wohex boltsand hex _
insertlocknuts.ff you hit a_orr_lgnobje¢_0rtc_I,_m,Ih_ snowthrowerIs _._ _._ Hex Botts
des]gffedsothattha hexbo_tswill$he_r.Tworeplacementhexl_ffs and _ 5116-18 X 1-1/2"
nulsare providedf_ryour cQnvenlenceSt_re}n_5_fep_aceortl_l_eeded _ Long
NN (71o.o o)
Ferrule Hairpin Ctips--'-_ _)
*_'(711-0677) (714-0104) _'_
_/"_ Flat Washers
_j"_-5116' LD. x 518" O.D°
(736-0264)
(_4-_Sprtng Washer Hex Nuts
5116" LO,. (Coma with
(736-0271) Clutch Cables
Hex Lock Nuts
5t16-18 Thread
(712-0158)

,=,= i= ,, = =,,,=,,H,,,,=,,,,,,i,, ,
ASSEMBLY INSTRUCTBONS
, i11,,,1 H 1111 l=,,,r =,1],,_1,1 i
HOWTOSET-UPYOURSNOWTHROWER
Bolt 1-3/4"
Long
FIGURE 1.
WARNING: MAKE CERTAIN THE
_SPARK PLUG WIRE IS DISCONNECTED
AND MOVED AWAY FROM THE SPARK
PLUG BEFORE ASSEMBLING THE
SNOW THROWER.
Cupped
Washer Hex
Jut
O
ATTACHING THE HANDLE ASSEMBLY
(Hardware A)
®Stretch out control cables and place on the floor.
®Place right handle in position with fiat side against
the snow thrower,r Secure bottom holes in handle
to snow thrower using hex bolts 5/8" long and lock
washers. See figure 1. Do not tighten at this time.
PIace handle tabs over the upper holes in handle,
so the curve in the handle tab matches the curve in
the handles. Secure to the snow thrower using hex
bolts 1-3/4" long and lock washers Do not tighten
at this time.
eAttach the left handle in the same manner, Do not
tighten at this time
ePlace the handle panel in position between the
handles, Secure with four carriage botts, cupped
washers (cupped side against the handle panel)
and hex nuts as shown in figure 2.
Tighten the four hex bolts used to attach the bot-
tom of the handles to the snow thrower frame.
O
FIGURE 2, Carriage
Bolt
FIGURE 3.
,Assembly
Hex Bolt
Hex Lock Nut
Chute Flange
Keeper
ATTACHING THE CHUTE ASSEMBLY
(Hardware B)
eGrease the chute opening using a multi-purpose
automotive grease or equivalent.
•Place chute assembly over chute opening, with the
opening in the chute assembly facing the front of
the unit, Place chute flange keepers beneath lip of
chute assembly. Insert hex bolt up through chute
flange keeper and chute assembly as shown in
-_----figure 3. Secure with hex lock nut,,After assembling
all three chute flange keepers, tighten then back off
1/4 turn to allow easier movement_
6

Upper /)
Chute
Crank 11
Bracket
FIGURE 4.
Lower
Chute
Crank
Bracket
ATTACHING THE CHUTE CRANK (Hardware C)
• Insert hex bolt through the upper chute crank
bracket. See figure 4.
e Place the hex bolt into the hole provided in the left
handle. Secure with lock washer and hex nut. Do
not tighten until after attaching the other end of the
chute crank.
Carriage Bolts
Hex Lock Nuts
eLoosen the carriage bolts and hex lock nuts which
secure the lower chute crank bracket to the exten-
sion on the left side of the chute assembly. See
figure 5.
FIGURE 5.
_W Flat
ashers
Chute
Crank
Cotter
Pin Lower
Chute C
Bracket
FIGURE 6. Plastic
Bushing
Cable
Guide
FIGURE 7,
ePlace one flat washer on the end of the chute
crank, then insert the end of the crank into the hole
in the plastic bushing in the chute crank bracket.
See figure 6, Place the other flat washer on the end
of the chute crank, and insert cotter pin into hole in
the end of crank, Secure by bending the ends of
cotter pin in opposite directions_
eAdjust the chute bracket so that the spiral on the
chute crank fully engages the teeth on the chute
assembly. Tighten the nuts on the lower chute
crank bracket securely, Tighten the hex bolt and
nut on the upper chute crank bracket on the
handle.
eSlip the cables that run from the handle panel to
the chute into the cable guide located on top of the
-._--- engine. See figure 7.

.....=, =IH'"H ........... =H=' =l ' 'I=HH= .....
ASSEMBLY iNSTRUCTIONS
= = =i Jill ll', m'H,='=,', =11 "H l=' I'
IMPORTANT: Attach the shift rod and clutch cables as follows. THEN CHECK THE ADJUSTMENTS AS I
INSTRUCTED, AND MAKE ANY FINAL. ADJUSTMENTS NECESSARY BEFORE OPERATING YOUR
SNOW THROWER. Failure to follow the instructions may cause damage to the snow thrower.
Traction
Drive
Clutch
Lower ......j
Hole in
Shift
Lever
Spring (_/_ i
Washer_
Hairpin Flat
Clip Washer
FIGURE 8.
Shift
Lever
Hairpin
Clip
O
ATTACHING THE SHIFT ROD (Hardware D)
eInsert the ferrule through the lower hote in the shift
lever beneath the handle panel from the right side°
Secure with flat washer and hairpin clip. See figure
8.
Place the shift lever in the sixth (6) speed position
(all the way forward),
e Start threading the shift rod into the ferrule. Push
down on the shift arm assembly as far as it will go.
Thread shift rod into the ferrule until the end of the
shift red lines up with the hole in the shift arm
assembly. Secure with spring washer, fiat washer
and hairpin clip.
Make certain to check for correct adjustment of the
shift rod as instructed in the Final Adjustment section
before operating the snow thrower_
ATTACHING THE CLUTCH CABLES
The "Z" ends of the clutch cables are hooked into the
clutch grips on each handle., Attach cables as follows.
e Thread the hex lock nuts (in hardware pack) all the
way up the threaded portion of the "Z" ends of the
clutch cables°
e Make certain each cable is in groove of cable roller
guides. Place the clutch grip in the raised (up) posi-
tion.
e Thread the cable onto the threaded portion of the
"Z" and until there is no slack in the cable, but the
cable is NOT tight. Do not overtighten cable
See figure 9
He]( Jam
Nut
Cable
is Straight
"Z" End
FIGURE 9.--Viewed from underside of handle
panel.
WARNING: IF CABLE IS TIGHTENED SO t
THERE IS TENSION ON THE CABLE I
WITH THE CLUTCH GRIP RELEASED,!
THE SAFETY FEATURES OF THE SNOW I
THROWER MAY BE OVERRIDDEN. I
e When correct adjustment is reached, tighten the
hex nut against the bottom portion of the cable to
lock it in position

ii i nnn,n ,,
ASSEMBLY iNSTRUCTIONS
i
ATTACHING THE LEFT AND RIGHT TRACK
CONTROLS
• Remove the screw from the top of the right hand
track control, Be careful not to lose the flat weld nut
that is inside the control.
•Place the right track control in position underneath
the right handle. Secure with screw just removed.
See figure 10
e Secure the left track control in the same manner,
FIGURE '10.
Right
Track .._ "I"_
Control
FINALADJUSTMENTS
Auger Drive Clutch
To check the adjustment of the auger drive clutch,
push forward on the left hand clutch grip (depress the
rubber bumper). There should be slack in the cabie_
Release the clutch grip The cable should be straighL
Make certain you can depress the auger drive clutch
grip against the left handle completely..
If necessary, loosen the hex jam nut and thread the
cable in or out as necessary. Refer to figure 9.
Recheck the adjustment° Tighten the jam nut against
the cable when correct adjustment is reached.
Traction Drive Clutch and Shift Lever Adjustment
To check the adjustment of the traction drive clutch
and shift lever, tip the snow thrower forward so that it
rests on the auger housing° First move the shift lever
all the way forward to sixth (6th) position. With the
traction drive lever released, turn the snow thrower
tracks by hand. They should turn freely. Then engage
the traction drive clutch grip and try to turn the tracks
The tracks should not move
Now release the traction drive clutch grip, and turn the
tracks again. Move the shift lever back to the fast
reverse position, then all the way forward again..
There should be no resistance in the shift lever, and
you should be able to turn the tracks by hand.
If you have resistance when moving the shift lever or
you are unabIe to turn the tracks by hand, loosen the
lock nut on the traction drive cable and unthread the
cable one turn If you are able to turn the tracks when
you engage the traction drive clutch grip, ioosen the
lock nut on the traction drive cable and thread the
cable in one turn_ Recheck the adjustment and repeat
adjustment as necessary.. Tighten the lock nut to
secure the cable when correct adjustment is reached
Adjusting the Skid Shoes
The space between the shave plate and the ground
can be adjusted° For close snow removal, place skid
shoes in the low position, Use middle or high position
when area to be cleared is uneven., See figure 11.r
Adjust skid shoes by loosening the four hex nuts and
carriage bolts and moving skid shoes to desired posi-
tion. Make certain the entire bottom surface of skid
shoe is against the ground to avoid uneven wear on
the skid shoes Retighten nuts and bolts securely.
H
FIGURE 11. Carriage Bolts

OPERATION
i = i, ='='"=H",'H ' =,HI
KNOWYOUR SNOW THROWER
READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR SNOW THROWER.
Compare the illustrations with your snow thrower to familiarize yourself with the location of various controls and
adjustments. Save this manual for future reference
Discharge Auger
Chute Chute
Tilt
Control
Left
Track
Control
Chute
Crank
Traction
Drivel
Auger
Clutch
Lock
Right
Track
Control
Auger
FIGURE 12.
Track
Auger
Skid Housing
Shoe
, ,=,, ,,,,,H, L
MEETSANS! SAFETYREQUIREMENTS
Sears snow throwers conform to the safety standards of the American National Standards Institute.
OPERATINGCONTROLS
SHIFT LEVER (See figures 12)
The shift lever is tocated in the center of the handle
panel The shift lever may be moved into one of eight
positions, Run engine with throttle in the fast position,
Use the shift lever to determine ground speed°
Forward---one of six speeds, Position number one (1)
is the slowest, Position number six (6) is the fastest
Reverse---two reverse (R) speeds, "R" closest to the
operator (atl the way back) is the faster of the two_
AUGER DRIVE CLUTCH (See figure 12)
The auger drive clutch is located on the left handle.
Squeeze the auger drive clutch against the handle to
engage the augers_ Release to stop the snow throw-
ing action. (Traction drive clutch must also be
released.)
10

i i1,1 iiiiii1,1111r111 OPERATION
......................... i i iiiii1,11,11 i ui,ii,
TRACTION DRIVE/AUGER CLUTCH LOCK
(See figure t2)
The traction drive clutch is located on the right handle,
Squeeze the traction drive clutch to engage the wheel
drive. Release to stop
This same lever also locks the auger clutch so you
can turn the chute crank without interrupting the snow
throwing process,. If the auger drive clutch is engaged
with the traction drive clutch engaged, the operator
can release the auger drive clutch (on the left handle)
and the augers wil! remain engaged. Release the
traction drive clutch to stop both the augers and wheel
drive (auger drive clutch must also be released).
CHUTE CRANK (See figure 12)
The chute crank is located on left hand side of the
snow thrower
To change the direction in which snow is thrown, turn
chute crank as follows:
1_ Crank clockwise to discharge to the left.
2, Crank counterclockwise to discharge to the right.
iiiiiiiiiiiii1,,,111
JI
Packed
Snow
FIGURE 13.
THROTTLE CONTROL (See figure 14)
The throttle control is located on the engine, It regu-
lates the speed of the engine.
LEFT AND RIGHT TRACK CONTROLS
The left and right track controls are located on the
underside of the handles and are used to assist in
steering your snow thrower_ See figure 12, Squeeze
the right track control when turning right, squeeze the
left control when turning left. Operate your snow
thrower in open areas until you become familiar with
these controls.
CHUTE TILT CONTROL
The distance snow is thrown can be adjusted by
adjusting the angle of the chute assembly,, Move the
chute tilt control forward to decrease the distance,
toward the rear to increase See figure 12,,
SAFETY IGNITION SWITCH (See figure 14)
The ignitionkey must be inserted in the switch before
the unit wil! start° Remove the ignition key when snow
thrower is not in use.
Box
Spark Starter
Button Rope Starter
Handle
TRACK LOCK LEVER
The track lock lever is located on the right side of the
snow thrower and is used to select the position of the
housing and the method of track operation. See figure
13. Move the lever to the right, then forward or back-
ward to one of the three positions,
Transport--Raises the front end of the snow thrower
for easy transport. May also be used on gravel drive-
ways to clear snow and leave gravel undisturbed.
Normal Snow--Allows the tracks to be suspended
independently for continuous ground contact
Packed Snow--Locks the front end of the snow
thrower down to the ground for hard-packed or icy
snow conditions
tgKey
FIGURE 14.
Throttle
Control
HEAD LAMP (8 H.P° Only)
The head lamp is on whenever the engine is running°
'11

H= ,=,r=l ,,,H...................... H,,, ,= =,,,
OPERATION
................................................. = HiM=' " MI'
BEFORE USING YOUR SNOW THROWER, AGAIN REFER TO THE "SAFETY RULES" AS SHOWN ON PAGE
2 OF THIS MANUAL ALWAYS BE CAREFUL,
The operation of any snow thrower can result in foreign objects being thrown into the
eyes, which can result in severe eye damage,, Always wear safety glasses or eye
shields before starting power tool operation or while performing any adjustments or
repairs, We recommend Wide Vision Safety Mask for over spectacles or standard
safety glasses available at Sears Retail or Catalog Stores.
TOSTOP ENGINE
oRemove the ignition key from the carburetor cover
on the engine (do not turn), See figure t4.
eDisconnect spark plug wire and move away from
spark plug to prevent accidental starting while
equipment is unattended_
HOWTOUSEYOURSNOWTHROWER
The snow thrower is propelled by the two tracks,
TO ENGAGE DRIVE
® With the engine running near top speed, move shift
lever into one of the six FORWARD positions or
two REVERSE positions, Select a speed appropri-
ate for the snow conditions that exist. Use the slow-
er speeds until you are familiar with the operation
of the snow thrower.
e Squeeze the left hand auger drive clutch to engage
it.
e White the left handle auger drive clutch is engaged,
engage the right hand traction drive/auger clutch
lock.
oRelease the left hand auger drive clutch only_ The
interlock mechanism should keep the left hand
auger drive clutch engaged until the right hand
traction drive/auger clutch !ock is released..
Release it and the drive motion will stop.
NOTE: NEVER move shift lever without first releasing
the drive clutch.
e Set the track lock lever in one of the three posi-
tions: transport, normal snow or packed snow. See
figure 13.
DISCHARGE CHUTE
The direction snow is thrown can be changed by turn-
ing the chute control crank,,
e Turn clockwise to discharge to the left.
•Turn counterclockwise to discharge to the right.
The distance snow is thrown can be changed by
adjusting the upper chute tilt control
• Move the tilt control forward to decrease the dis-
tance..
®Move the tilt control to the rear to increase the dis-
tance.
BEFORESTARTING
OIL
e Only use high quality detergent oil rated with API
service classification SF or SG Use SAE 5W-30
oil
eSAE 10W is an acceptable substitute. (Do not use
t0W-40)
® Oil sump capacity:
5 H,P. Engine 1-1/4 pints (19 ounces)
8 HP, Engine 1-5/8 pints (26 ounces)
• Maintain oil level between "FULL" and "ADD"
marks on dipstick,,
e Remove oil fill plug and dipstick.
e Wipe dipstick clean, insert it into oil fill hole and
tighten securely, Remove dipstick. If oil is not up to
"FULL" mark on dipstick, add recommended oil
POUR SLOWLY. Wipe dipstick ctean each time oil
level is checked
IMPORTANT: DO NOT FILL ABOVE "FULL"
MARK ON DIPSTICK..
e Instatl oi! fill plug and dipstick. Tighten securely,
Oil Fill
Plug and_ Fuel
Tank
Dipstick X_k
FIGURE t5.
12
Oil Drain Plug

OPERATION
=N''HH==r',,' = = =
GAS
eRemove fuel cap and fill fuel tank with about 3
quarts of clean, fresh, lead-free grade automotive
gasoline DO NOT use Ethyl or high octane gaso-
line. Be certain container is clean and free from
rust or foreign particles. Never use gasoline that
may be stale from tong periods of storage in the
container Replace fuel cap.
WARNING: DO NOT FILL CLOSER
THAN 1/2 INCH OF TOP OF FUEL TANK
TO PREVENT SPILLS AND TO ALLOW
FOR FUEL EXPANSION. IF GASOLINE
IS ACCIDENTLY SPILLED, MOVE SNOW
THROWER AWAY FROM AREA OF
SPILL. AVOID CREATING ANY SOURCE
OF IGNITION UNTIL GASOLINE
VAPORS HAVE DISAPPEARED.
Check the fuel level periodically to avoid running out
of gasoline while operating the snow thrower. If the
unit runs out of gas, it may be necessary to unclog the
unit before it can be restarted. Refer to Service and
Adjustment section..
WARNING: EXPERIENCE INDICATES THAT ALCO-
HOL BLENDED FUELS (CALLED GASOHOL OR
USING ETHANOL OR METHANOL) CAN ATTRACT
MOISTURE WHICH LEADS TO SEPARATION AND
FORMATION OF ACIDS DURING STORAGE.
ACIDIC GAS CAN DAMAGE THE FUEL SYSTEM
OF AN ENGINE WHILE IN STORAGE° TO AVOID
ENGINE PROBLEMS, THE FUEL SYSTEM
SHOULD BE EMPTIED OR TREATED WITH FUEL
STABILIZER BEFORE STORAGE FOR 30 DAYS
OR LONGER. USE FRESH FUEL NEXT SEASON.
SEE "STORAGE" SECTION FOR ADDITIONAL
INFORMATION.
NEVER USE ENGINE OR CARBURETOR CLEAN-
ER PRODUCTS IN THE FUEL TANK OR PERMA*
NENT DAMAGE MAY OCCUR.
'I=",'"="'"HH'=......................................... ,'=, H=,'=,Hm=I H= =
•To start a cold engine, push primer button one
time_ Use a firm push. This step is not necessary
when starting an engine which has been run for a
few minutes.
®Connect power cord to plug on snow thrower, then
to a three-hole, grounded 120-volt AC household
outlet.
WARNING: ALWAYS CONNECT POWER
CORD TO PLUG ON SNOW THROWER
FIRST, THEN PLUG THE OTHER END IN
THE HOUSEHOLD OUTLET. WHEN DIS*
CONNECTING, ALWAYS UNPLUG
FROM THE HOUSEHOLD OUTLET
FIRST.
ePush starter button to engage starter motor and
crank engine.
IMPORTANT: THIS ELECTRIC STARTER IS NOT
EQUIPPED WITH A THERMAL
CUTOUT SWITCH. DO NOT CRANK
ENGINE FOR MORE THAN A TOTAL
OF 20 SECONDS WITHOUT ALLOW-
ING ELECTRIC STARTER TQ COOL
DOWN FOR 10 MINUTES, OR
SEVERE DAMAGE TO ELECTRIC
STARTER CAN RESULT.
NOTE: If the starter motor runs but the engine does
not turn over, the starter gear is apparently covered
with ice and frozen. Place the unit in a warm atmo-
sphere until the gear is free and the starter will
engage.
eAfter engine starts, release starter button, Allow the
engine to warm up for a few minutes Then move
choke gradually to OFF position° If engine falters,
return to ON position, then slowly move to OFF
position.
®Unplug the power cord from the household outlet,
then from the plug on snow thrower
USING THE RECOIL STARTER
TOSTARTENGINE
USING THE ELECTRIC STARTER
•Make certain the auger control handle is disen-
gaged (released)..
•Insert ignition key into ignition switch Do not turn.
®To start a cold engine, move choke lever to QN
position. If you are starting an engine which has
already been run for a few minutes, do not choke.
eMake certain auger control handle is disengaged
(released).
® Insert ignition key into ignition switch. Do not turno
eTo start a cold engine, move choke lever to ON
position if you are starting an engine which has
already been run for a few minutes, do not choke
®To start a cold engine, push primer button two or
three times. Use a firm push. This step is not nec-
essary when starting an engine which has been run
for a few minutes.
13

= H,=,'H"H,' ====='I
NOTE: If the temperature is below 15°F,, additional
priming may be necessary for initiaJ start only.
® Grasp starter handle and pull rope out slowly, until
it pulls slightly harder° Let rope rewind slowly..
® Pull starter handle rapidly. Keep a firm hold on the
hand}e and allow it to rewind slowly. Do not allow
handte to snap back.
e If engine fails to start after 3 pulls on the starter
handle, prime engine two times and pull starter
handle again,
e After engine starts and begins to operate evenly,
move choke lever gradually to OFF position. If
engine falters, return to ON position, then slowly
move to OFF position_
AVOIDINJURYFROM
ROTATINGAUGER-
KEEPHANDS,FEET,
ANDCLOTHINGAWAY!
WARNING: TEMPERATURE OF MUF-I
FLER AND SURROUNDING AREAS MAY I
EXCEED 150°F. AVOID THESE AREAS. I
J
OPERATINGTIPS
® Use your snow thrower to remove fresh snow
before it is packed down by footprints or tire tracks
® Discharge snow in the direction the wind is blowing
whenever possible.
® Slightly overlap each previous swath°
e Snow up to about an 8 inch depth can be removed
easily by walking at a moderate rate° Slow your
pace for wet or deep snow.
® Run engine for a few minutes before stopping to
help dry off any moisture on the engine
14

Check Engine Oil I' =
uJ Change Engine Oil _/ 1'
Z ', .... : :
Service Air Cleaner 1'
Z............................ , , .........
I.u Spark Plug #
Muffler 4
1' CHECK
GENERALRECOMMENDATIONS
WARNING: ALWAYS STOP THE ENGINE
AND DISCONNECT THE SPARK PLUG
WIRE BEFORE PERFORMING ANY
MAINTENANCE OR ADJUSTMENTS,
®Periodically check all fasteners and be sure they
are tighL
® Follow the Maintenance Schedule above
LUBRICATION
Gear Shaft
Lubricate the gear shaft with grease at least once a
season or after every 25 hours of operation,
IMPORTANT: Keep all grease and oil off of the
friction wheel and drive plate.
Shifting Mechanism
Lubricate the shifting mechanism and pivot points on
the shift rod with engine oil at least once a season or
after every 25 hours of operation.,
Traction Drive/Auger Clutch Lock
The cams on the ends of the control rods which inter-
lock the traction drive and auger drive clutches must
be lubricated at least once a season or every twenty-
five hours of operation with grease, The cams can be
accessed beneath the handle panel
Gear Case
The gear case is lubricated with grease at the factory
and does not require checking,, If disassembled for
any reason, lubricate with 2 ounces of Shell Atvania
grease, part number 737-0168.
Bearings
Lubricate the auger bearings, wheet bearings and the
bearings on the side of the frame once a season with
light oil
15

,111,11,1,1 i i ii iii,
CUSTOMER RESPONSiBiLiTiES
iiiir,lrl ii ............................ i
AUGERS
The augers are secured to the spiral shaft with two
hex bolts and hex lock nuts° See figure 16. If you hit a
foreign object or ice jam, the snow thrower is
designed so that the hex bolts will shear.
If the augers will not turn, check to see if the hex bolts
have sheared. Two replacement hex bolts and hex
lock nuts have been provided with the snow thrower
For future use, order part number 710-0890 (hex bolt
5/16-18 x 1.5" long) and 7t2-0429 (hex insert lock nut
5/16-18 thread)..
iii, iiiiii1,1111 i iiiiiii ,i
tighten securely_ Remove dipstick. If oit is not up to
"FULL" mark on dipstick, add recommended oil,
POUR SLOWLY, Wipe dipstick clean each time oil
level is checked
IMPORTANT: DO NOT FILL ABOVE "FULL" MARK
ON DIPSTICK.
e Install oil fill plug and dipstick, tighten securely_
To Drain OIh
® Drain oil while engine is warm.
a, Remove oil drain plug. Refer to figure 15_Catch
oil in a suitable container,
Auger Bolts
b. When engine is drained of all oil, replace drain
plug securely..
eRefill with fresh oil Refer to before starting in the
operation section,
e Replace dipstick.
FIGURE 16.
ENGINE
ENGINE OIL
eOnly use high quality detergent oi! rated with API
service classification SF or SG Use SAE 5W-30
oil
• SAE 10W is an acceptable substitute.. (Do not use
lOW-40),,
• Oi{ sump capacity:
5 HP, Engine 1-1/4 pints (19 ounces)
8 H°P, Engine 1-5/8 pints (26 ounces)
e Maintain oil level between "FULL" and "ADD"
marks on dipstick
• Remove oil fill plug and dipstick.
e Wipe dipstick clean, insert it into oil fill hole and
SPARK PLUG
The spark plug should be cleaned and the gap reset
to .030" at least once a season or every 50 hours of
operation See figure t7 Spark plug replacement is
recommended at the start of each season. Refer to
engine parts list for correct spark plug type.
NOTE: Do not sandblast spark plug.. Spark plug
should be cleaned by scraping or wire brushing and
washing with a commercial solvenL
Feeler Gauge
\
Spark Plug
FIGURE t7.
16

nj ................................. I= IH ,,,,,',,,,,,,,,,,I =........................
STORAGE
=, ,n,
Prepare your snow thrower for storage at the end of
the season or if the unit will not be used for 30 days or
more
WARNING: NEVER STORE MACHINE
WITH FUEL IN THE FLtEL TANK INSIDE
OF BUILDING WHERE FUMES MAY
REACH AN OPEN FLAME OR SPARK,
OR WHERE IGNITION SOURCES ARE
PRESENT SUCH AS HOT WATER AND
SPACE HEATERS, FURNACES,
CLOTHES DRYERS, STOVES, ELEC*
TRIC MOTORS, ETC.
NOTE: A yearly check-up by your local Sears Service
Center is a good way to make certain your snow
thrower will provide maximum performance for the
next season.
SNOWTHROWER
eCtean the snow thrower thoroughly
e Wipe unit with an oiled rag to prevent rust (use a
light oil or silicone)_
ENGINE
IMPORTANT: IT [S IMPORTANT TO PREVENT
GUM DEPOSITS FROM FORMING IN ESSENTIAL
FUEL SYSTEM PARTS SUCH AS CARBURETOR,
FUEL FILTER, FUEL HOSE, OR TANK DURING
STORAGE ALSO, EXPERIENCE INDICATES THAT
ALCOHOL BLENDED FUELS (CALLED GASOHOL
OR USING ETHANOL OR METHANOL) CAN
ATTRACT MOISTURE WHICH LEADS TO SEPARA-
TION AND FORMATION OF ACIDS DURING STOR-
AGE. ACIDIC GAS CAN DAMAGE THE FUEL SYS-
TEM OF AN ENGINE WHILE IN STORAGE,
•Drain the fuel tank_
® Start the engine and let it run until the fuel lines and
carburetor are empty..
oNever use engine or carburetor cleaner products in
the fuel tank or permanent damage may occur.
oUse fresh fuel next season..
NOTE: Fuel stabi!]zer is an acceptable alternative in
minimizing the formation of fuel gum deposits during
storage. Add stabilizer to gasoline in fuel tank or stor_
age container Always follow the mix ratio found on
stabilizer container Run engine at least 10 minutes
after adding stabilizer to allow the stabilizer to reach
the carburetor° Do not drain the gas tank and carbure-
tor if using fuel stabilizer
e Drain all the oil from the crankcase (this should be
done after the engine has been operated and is still
warm) and refill the crankcase with fresh oil
e If you have drained the fuel tank, protect the inside
of the engine as follows. Remove spark plug, pour
approximately 1/2 ounce (approximately one table-
spoon) of engine oi_ into cytinder and crank slowly
to distribute oil.. Replace spark plugo
OTHER
eDo not store gasoline from one season to another°
e Replace your gasoline can ifyour can starts to rust,
Rust and/or dirt in your gasoline will cause prob-
lemso
e Store unit in a clean, dry area,, Do not store next to
corrosive materials, such as fertilizer,
NOTE: If storing in an unventilated or metat storage
shed, be certain to rustproof the equipment by coating
with a light oil or silicone
WARNING: ALWAYS STOP ENGINE I
AND DISCONNECT SPARK PLUG WIRE I
AND MOVE tT AWAY FROM SPARK I
PLUG BEFORE PERFORMING ANY I
ADJUSTMENTS OR REPAIRS. I
SHAVEPLATEAND SKIDSHOES
®The shave plate and skid shoes on the bottom of
the snow thrower are subject to wear. They should
be checked periodically and replaced when neces-
sary.
eTo remove skid shoes, remove the four carriage
bolts, bellevitle washers and hex nuts which attach
them to the snow thrower. Reassemble new skid
shoes with the four carriage botts, betleville wash-
ers (cupped side goes against skid shoes) and hex
nuts. Make certain the skid shoes are adjusted to
be level.
oTo remove shave plate, remove the carriage bolts,
beHeville washers and hex nuts which attach it to
the snow thrower housing_ Reassemble new shave
plate, making sure heads of the carriage bolts are
to the inside of the housing Tighten securely
17

SERVICE & ADJUSTMENT
i1,11,1 i ii ii iii1,, iiiiiiii1,1111r,i ii i1,11,,,i
BELTREMOVALANDREPLACEMENT
WARNING: DISCONNECT THE SPARK I
PLUG WIRE FROM THE SPARK PLUG I
AND GROUND.
To remove and replace either the rear or front auger
drive belt, proceed with the following instructions.
• Disconnect the chute crank at the chute assembly
by removing the cotter pin and flat washer.
®Remove the plastic belt cover on the front of the
engine by removing two self-tapping screws.. See
figure 18,.
FIGURE 19.
Frame
Hex Bolts
Washers
Hex Nuts
Auger
Assembly
Cover ._Self-Tapping
Screws
FIGURE 18,
• Unthread the bottom of the auger cable from the
top of the cable, leaving the hex nut in place.
• Remove the six hex bolts, lock washers and hex
nuts which attach the auger housing assembly to
the frame. See figure 19.
®Separate the housing from the frame assembly by
standing in the operating position and lifting up on
the handles. The frame and housing will separate,
and the rear auger drive belt wilt come off the pul-
leys, See figure 20
e To remove the front auger drive bett, push the idler
pulley to the left, and lift front auger drive belt from
the front auger pulley.. See figure 21. Replace both
auger drive belts by following instructions in
reverse order.
18
t
FIGURE 20.
Auger
ulley
FIGURE 21,
Frame
Auger
Housing
Front
Auger
Drive
Belt

...................................SERVICE & ADJUSTMENT
iii iilii i iili i iiiiii iiiiiiiiiiim, = Hum,==rHm==, i iiiiii i llilill i ii illlli,ill iililllli i lii liliill I
eIf a replacement drive belt is needed, follow • Remove the six screws from the friction wheel
previous instructions. Pull idler pulley up and lift assembly (three from each side).. Remove the fric-
belt off friction wheel disc. See figure 22. tion wheel rubber from between the friction wheel
Reassemble in reverse order, plate,.
• Reassemble new friction wheel rubber to the fric-
tion wheel assembly, tightening the six screws in
rotation and with equal force.
®Slide the friction wheel assembly up onto the shift
Idler mechanism as shown in figure 24, and slide the
Pulley gear shaft back into the unit. Reassemble in
reverse order.
NOTE: When reassembling the two halves of the unit,
the auger drive cable must be routed through the
cable roller guides as shown in figure 22
FIGURE 22,
Friction
Wheel
Disc
Cable
Roller
Guide
Cable
Hex Bolt
Lock Washer
Flat Washer
FIGURE 23.
Track
CHANGINGTHE FRICTIONWHEEL
RUBBER
The rubber on the friction wheel is subject to wear
and should be checked after 25 hours of operation,
and periodically thereafter_ Replace the friction wheel
rubber if any signs of wear or cracking are found°
oDrain the gasoline from the snow thrower, or place
a piece of plastic under the gas cap.
• Tip-the snow thrower up and forward, so that it
rests on the housing.
•Remove four self-tapping screws from the frame
cover underneath the snow thrower
•Remove the gear shaft from the unit by removing
the bolts, lock washers and flat washers from each
side of the frame. See figure 23_ Hold the friction
wheel assembly, and slide the gear shaft out of the
unit toward the right hand side. Refer to figure 24.
19
TRACTIONDRIVE CLUTCHADJUSTMENT
Refer to the Final Adjustment section of the Assembly
Instructions to adjust the traction drive clutch. If you
are uncertain that you have reached the correct
adjustment, the adjustment can be physically checked
as follows,.
With the snow thrower tipped forward (be certain to
drain the gasoline or place plastic film under the gas
cap if the snow thrower has already been operated),
remove the frame cover underneath the snow thrower
by removing four self-tapping screws. With the trac-
tion drive clutch released, there must be clearance
between the friction wheel and the drive plate in all
positions of the shift lever. With the traction drive
clutch engaged, the friction wheel must contact the
drive plate See figure 24

SERV!CE &ADJUSTMENT
If adjustment is necessary, loosen the lock nut on the
traction drive cable and thread the cable in or out as
necessary Tighten the lock nut to secure the cable
when correct adjustment is reached,, Reassemble the
frame cover.
NOTE: If you placed plastic under the gas cap, be
certain to remove it
Friction
Wheel
'UII=,I, 'n'Hn IH=
5 H,P. ENGINE
Idle Speed Adjustment. This screw is located on top
of the carburetor and contacts the throttle To initially
pre-adjust this speed, back out the screw, then turn in
until the screw just touches the throttle lever, then turn
screw in 1 turn When the engine is run, the final idle
R.P.M can be adjusted with a tachometer
Idle and Main Adjustment. Turn these adjustment
screws in finger tight, then back them out to the pre-
set figure on the chart.
TECUMSEH CARBURETOR PRE-SETS
Drive
Plate
Gear Shaft
FIGURE 24_
AUGERCLUTCHADJUSTMENT
To adjust the auger clutch, refer to Final Adjustment
section of Assembly Instructions.
SHIFTROD ADJUSTMENT
To adjust the shift rod, remove the hairpin clip and flat
washer which secure the shift rod to the shift arm
assembly Refer to figure 8. Adjust as specified in
Assembly instructions
CARBURETORADJUSTMENT
WARNING: IF ANY ADJUSTMENTS ARE
MADE TO THE ENGINE WHILE THE
ENGINE IS RUNNING (E.G. CARBURE-
TOR), KEEP CLEAR OF ALL MOVING
PARTS. BE CAREFUL OF HEATED SUR-
FACES AND MUFFLER.
Minor carburetor adjustment may be required to com-
pensate for differences in fuel, temperature, altitude
or load
Never attempt to change maximum engine speed, it is
pre-set at the factory and should be changed only by
a qualified service technician who has the necessary
equipment,
ENGINE
MODELS
5H,Po MAIN j IDLE
PRE-SET PRE-SET
1-1/4 1
Final Carburetor Adjustments
Allow engine to warm up to a normal running temper-
ature. With engine running at maximum recom-
mended R.P,M, Ieosen main adjustment screw until
engine starts to cut out. Then turn screw opposite
direction until engine starts to cut out, Note the num-
ber of turns from one extreme to the other Loosen
screw to a point midway between the extremes
After the main system is adjusted, move the speed
control lever to the idle position and follow the same
procedure for adjusting the idle system.
Test the engine by running it under a normal load.
The engine should respond to load pick-up immedi-
ately An engine that "dies" is too lean
An engine which ran rough before picking up the load,
is adjusted too rich
If adjustment seems too "touchy" check float for prop-
er setting and for sticking
8 H.P. ENGINE
Preset the carburetor by turning both idle and main
adjustment screw closed (clockwise) fingertighL Open
the main adjustment screw 2 turns (counterclockwise)
and the idle adjustment screw 1-3/4 turns.
Generally, the engine wilt perform well with these set-
tings If further adjustment is required, perform the fol-
lowing adjustments with the engine running and fully
warmed up.
With speed control lever at idle or slow speed, turn
the idle adjustment screw slowly, clockwise 1/8 turn at
a time until the lean drop off point is reached (The
engine will miss and run erratically due to lack of fuel.)
Now turn the screw counterclockwise 1/4 to 3/8 turn
from that position This will be the best setting
20