Craftsman INCREDI-PULL 316.791910 User manual

Operator's ManualRN°
4-Cycle
WEEDWACKER GAS TRIMMER
Model No. 316.791910
INCREDI.PULUNJ_TM
UNBELIEVABLE STARTING EASE TM
withMAX FIRE_IBN ITION °
CAUTION: Before using
this product, read this
manual and follow all
safety rules and operating
instructions.
•SAFETY
• ASSEMBLY
• OPERATION
• MAINTENANCE
• PARTS LIST
• ESPANOL, P. E1
Sears, Roebuck and Co., Hoffman Estates, IL 60179, U.S.A.
Visit our website" www.sears.com/craftsman
769-03535A

TABLE OF CONTENTS
Rules for Safe Operation ................................ 2
Warranty Information ................................... 4
Know Your Unit ........................................ 4
Assembly Instructions ................................... 5
Oil and Fuel Information ................................. 6
Starting/Stopping Instructions ............................ 7
Operating Instructions .................................. 8
Maintenance and Repair Instructions ....................... 9
Cleaning and Storage .................................. 13
Troubleshooting Chart ................................. 14
Specifications ........................................ 15
California Emission Control Warranty Statement ............. 15
Parts List ........................................... E19
Service Information ............................ Back Cover
SPARK ARRESTOR NOTE
NOTE: For users on U.S. Forest Land and in the states of
California, Maine, Oregon and Washington. All U.S. Forest Land
and the state of California (Public Resources Codes 4442 and 4443),
Oregon and Washington require, by law that certain internal
combustion engines operated on forest brush and/or grass-covered
areas be equipped with a spark arrestor, maintained in effective
working order, or the engine be constructed, equipped and
maintained for the prevention of fire. Check with your state or local
authorities for regulations pertaining to these requirements. Failure to
follow these requirements could subject you to liability or a fine. This
unit is factory equipped with a spark arrestor. If it requires
replacement, ask your LOCAL SERVICE DEALER to install the
Accessory Part #753-05297 Spark Arrestor Kit.
CALIFORNIA PROPOSITION 65 WARNING
The purpose of safety symbols is to attract your attention to possible
dangers. The safety symbols, and their explanations, deserve your
careful attention and understanding. The safety warnings do not by
themselves eliminate any danger. The instructions or warnings they
give are not substitutes for proper accident prevention measures.
SYMBOL MEANING
SAFETY ALERT: Indicates danger, warning or
caution. Attention is required in order to avoid serious
personal injury. May be used in conjunction with other
symbols or pictographs.
DANGER: Failure to obey a safety warning will result
in serious injury to yourself or to others. Always follow
the safety precautions to reduce the risk of fire, electric
shock and personal injury.
_lb WARNING: Failure to obey a safety warning can
result in injury to yourself and others. Always follow the
safety precautions to reduce the risk of fire, electric
shock and personal injury.
CAUTION: Failure to obey a safety warning may
result in property damage or personal injury to yourself I
or to others. Always follow the safety precautions to
reduce the r sk of f re, e ectr c shock and persona n ury.
NOTE: Advises you of information or instructions vital to the
operation or maintenance of the equipment.
THE ENGINE EXHAUST FROM THIS PRODUCT CONTAINS
CHEMICALS KNOWN TO THE STATE OF CALIFORNIA TO
CAUSE CANCER, BIRTH DEFECTS OR OTHER
REPRODUCTIVE HARM.
Read the Operator's Manual and follow all warnings and safety
instructions. Failure to do so can result in serious injury to the
operator and/or bystanders.
FOR QUESTIONS, CALL 1-800-659-5917
• IMPORTANT SAFETY INSTRUCTIONS •
READ ALL INSTRUCTIONS BEFORE OPERATING
I_ WARN ING: When using the unit, you must follow the I
safety rules. Please read these instructions before operating I
the unit in order to ensure the safety of the operator and any
bystanders. Please keep these instructions for later use.
• Read the instructions carefully. Be familiar with the controls and
proper use of the unit.
• Do not operate this unit when tired, ill, or under the influence of
alcohol, drugs, or medication.
• Children and teens under the age of 15 must not use the unit,
except for teens guided by an adult.
• All guards and safety attachments must be installed properly
before operating the unit.
• Inspect the unit before use. Replace damaged parts. Check for
fuel leaks. Make sure all fasteners are in place and secure.
Replace parts that are cracked, chipped, or damaged in any
way. Do not operate the unit with loose or damaged parts.
• Carefully inspect the area before starting the unit. Remove all
debris and hard or sharp objects such as glass, wire, etc.
• Be aware of the risk of injury to the head, hands and feet.
• Clear the area of children, bystanders, and pets. At a minimum,
keep all children, bystanders, and pets outside a 50 feet (15 m.)
radius; there still may be a risk to bystanders from thrown
objects. Bystanders should be encouraged to wear eye
protection. If you are approached, stop the unit immediately.
• Use only Craftsman XTRA QUIET TM 0.095 inch (2.413 mm)
diameter original equipment manufacturer replacement line.
Never use metal-reinforced line, wire or rope. These can break
off and become dangerous projectiles.
• Squeeze the throttle control and check that it returns automatically to
the idle position. Make all adjustments or repairs before using unit.
SAFETY WARNINGS FOR GAS UNITS
WARNING: Gasoline is highly flammable, and its
vapors can explode if ignited. Take the following
precautions:
• Store fuel only in containers specifically designed and approved
for the storage of such materials.
• Always stop the engine and allow it to cool before filling the fuel
tank. Never remove the fuel tank cap or add fuel when the engine is
hot. Never operate the unit without the fuel cap securely in place.
Loosen the fuel tank cap slowly to relieve any pressure in the tank.
• Add fuel in a clean, well-ventilated outdoor area where there are
no sparks or flames. Remove the fuel cap slowly, and only after
the engine stops. Do not smoke while fueling. Wipe up any
spilled fuel from the unit immediately.
• Avoid creating a source of ignition for spilled fuel. Do not start
the engine until fuel vapors dissipate.
• Move the unit at least 30 feet (9.1 m) from the fueling source and site
before starting the engine. Do not smoke. Keep sparks and open
flames away from the area while adding fuel or operating the unit.
WHILE OPERATING
• Never start or run the unit inside a closed room or building.
Breathing exhaust fumes can be fatal. Operate this unit only in a
well-ventilated outdoor area.
• Wear safety glasses or goggles that meet ANSI Z87.1-1989 standards
and are marked as such. Wear ear/hearing protection when operating

thisunit.Wearafaceordustmaskiftheoperationisdusty.
• Wearheavylongpants,boots,glovesandalongsleeveshirt.Do
notwearlooseclothing,jewelry,shortpants,sandalsorgo
barefoot.Securehairaboveshoulderlevel.
• Thecuttingattachmentshieldmustalwaysbeinplacewhile
operatingtheunitasatrimmer.Donotoperateunitwithoutboth
trimminglinesextended,andtheproperlineinstalled.Donot
extendthetrimminglinebeyondthelengthoftheshield.
• Thisunithasaclutch.Thecuttingattachmentremainsstationary
whentheengineisidling.Ifitdoesnot,havetheunitadjustedby
anauthorizedservicetechnician.
• Adjustthehandletoyoursizeinordertoprovidethebestgrip.
• Besurethecuttingattachmentisnotincontactwithanything
beforestartingtheunit.
• Usetheunitonlyindaylightorgoodartificiallight.
• Avoidaccidentalstarting.Beinthestartingpositionwhenever
pullingthestarterrope.Theoperatorandunitmustbeinastable
positionwhilestarting.RefertoStarting/Stopping Instructions.
• Use the right tool. Only use this tool for its intended purpose.
• Do not overreach. Always keep proper footing and balance.
• Always hold the unit with both hands when operating. Keep a
firm grip on both handles or grips.
• Keep hands, face, and feet at a distance from all moving parts.
Do not touch or try to stop the cutting attachment when it rotates.
• Do not touch the engine, gear housing or muffler. These parts
get extremely hot from operation, even after the unit is turned off.
• Do not operate the engine faster than the speed needed to cut, trim
or edge. Do not run the engine at high speed when not cutting.
• Always stop the engine when cutting is delayed or when walking
from one cutting location to another.
• If you strike or become entangled with a foreign object, stop the engine
immediately and check for damage. Do not operate before repairing
damage. Do not operate the unit with loose or damaged parts.
• Stop the unit, switch the engine to off, and disconnect the spark
plug for maintenance or repair.
• Use only replacement parts or accessories recommended forthis tool
that are distributed by Sears or a Craftsman outlet. Use of any
replacement parts or accessories purchased elsewhere may be
hazardous, and will also void your warranty.
• Keep unit clean of vegetation and other materials. They may
become lodged between the cutting attachment and shield.
• To reduce fire hazard, replace a faulty muffler and spark arrestor.
Keep the engine and muffler free from grass, leaves, excessive
grease or carbon build up.
OTHER SAFETY WARNINGS
• Never store the unit with fuel in the tank, inside a building where
fumes may reach an open flame (pilot lights, etc.) or sparks
(switches, electrical motors, etc.).
• Allow the engine to cool before storing or transporting. Be sure
to secure the unit while transporting.
• Store the unit in a dry area, locked up or up high to prevent
unauthorized use or damage, out of the reach of children.
• Never douse or squirt the unit with water or any other liquid.
Keep handles dry, clean and free from debris. Clean after each
use, see Cleaning and Storage instructions.
• Keep these instructions. Refer to them often and use them to
instruct other users. If you loan someone this unit, also loan them
these instructions.
SAVE THESE INSTRUCTIONS
•SAFETY AND INTERNATIONAL SYMBOLS •
This operator's manual describes safety and international symbols and pictographs that may appear on this product. Read the operator's
manual for complete safety, assembly, operating and maintenance and repair information.
SYMBOL MEANING
I" SAFETY ALERT S¥ MBOL
IIndicates danger warning or caution. May be used in
Iconjunction with other symbols 0r pictograph&
l•READ OPERATOR'S MANUAL
T I WARNING: Read theoPerat0r's manual(s)and
II I_1_1 II I follow all warnings and safety instructions. Failure to
do so can result in serious injury to the operator
and/or bystanders.
• WEAR EYE AND HEARING PROTECTION
WARNING: Thrown objects and loud noise can
cause severe eye injury and hearing loss. Wear eye
protection meeting ANSI Z87.1-1989 standards and
ear protection when operating this unit. Use a full
face shield when needed.
Ir_ I. UNLEADED FUEL
._ A,ways use c,ean , !!esh un,eaded fue L
• OIL i
Re!e!0°peia'°rsmanua,!or,hep!ope!y eo!o1,,
•KEEP BYSTANDERS AWAY
_Im_ WARNING: Keep all bystanders, especially
J\l*--_l¢_. children and pets at least 50 feet (15 m) from the
operating area.
SYMBOL MEANING
•ON/OFF STOP CONTROLON /START /RUN
• ON/O FF STOP CONTROL
OFF or STOP
•HOT SURFACE
WARNING: Do not touch a hot muffler, gear
housing or cylinder. You may get burned. These
parts get extremely hot from operation. They remain
hot for a short time after the unit is turned off.
_,_.,==A • THROWN OBJECTS AND ROTATING CUTTER
t/_/-_ CAN CAUSE SEVERE INJURY
f/ WARNING: Do not operate without the cutting
__f'_ attachment shield in place. Keep away from the
rotating cutting attachment.
H I',1I*1
123
•CHOKE CONTROL
1. ,FULL choke position
2. • PARTIAL choke oosition
3. • RUN choke position
,SHARP BLADE
WARNING: Sharp blade on cutting attachment
shield. To prevent serious injury, do not touch the
line cutting olade.

CRAFTSMANFULLWARRANTY
If this Craftsman product fails due to a defect in material or workmanship within two years from the date of purchase, return it to any Sears
store, Parts and Repair Service Center, or other Craftsman outlet in the United States for free repair (or replacement if repair proves
impossible).
This warranty applies for only 90 days if this product is ever used for commercial or rental purposes.
This warranty covers ONLY defects in materal and workmanship. Sears will NOT pay for:
• Expendable items that can wear out from normal use within the warranty period, such as cutting line, filters or spark plugs.
• Repairs necessary because of accident or failure to operate or maintain the product according to all supplied instructions.
• Preventive maintenance, or repairs necessary due to improper fuel mixture, contaminated or stale fuel.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
Repair Protection Agreements
Congratulations on making a smart purchase. Your new Craftsman® product is designed and manufactured for years of dependable operation.
But like all products, it may require repair from time to time. That's when having a Repair Protection Agreement can save you money and
aggravation.
Here's what the Repair Protection Agreement* includes:
[] Expert service by our 10,000 professional repair specialists
[] Unlimited service and no charge for parts and labor on all covered repairs
[] Product replacement up to $1500 if your covered product can't be fixed
[] Discount of 10% from regular price of service and related installed parts not covered by the agreement; also, 10% off regular price of
preventive maintenance check
[] Fast help by phone - we call it Rapid Resolution - phone support from a Sears representative. Think of us as a "talking owner's
manual."
Once you purchase the Repair Protection Agreement, a simple phone call is all that it takes for you to schedule service. You can call
anytime day or night, or schedule a service appointment online.
The Repair Protection Agreement is a risk-free purchase. If you cancel for any reason during the product warranty period, we will provide a
full refund. Or, a prorated refund any time after the product warranty period expires. Purchase your Repair Protection Agreement today!
Some limitations and exclusions apply. For prices and additional information in the U.S.A. call 1-800-827-6655.
*Coverage in Canada varies on some items. For full details call Sears Canada at 1-800-361-6665.
Sears Installation Service
APPLICATIONS
As a trimmer:
• Cutting grass and light weeds
• Decorative trimming around trees, fences, etc.
Spark Arrestor
Muffler
Muffler Guard
Starter Rope Grip
Shaft Grip
On/Off Stop Control
\
Spark Plug
Oil Fill
Plug/
Dipstick
D-Handle Choke
Lever Fuel
Cap
Shaft
Housing
Throttle
Control
Air Filter Cover
Primer
Bulb
Line
Cutting
Blade
Cutting Shield
Rapid Rewind TM Head

ADJUSTING THE D-HANDLE
1. Locate the wing nut on the D-Handle. Loosen the wing nut
enough to loosen the D-Handle (Fig. 1).
NOTE: Do not remove wing nut, washer, or bolt.
2. Rotate the D-Handle to the upright position on the front side
of the shaft housing (Fig. 1).
NOTE: The D-handle should slant towards the powerhead of the
unit.
3. Hold the unit in the operating position (Fig. 2). If necessary,
reposition the D-handle to the location that provides the best
gnp.
4. Tighten the wing nut until the D-Handle is secure.
Fig. 1 Fig. 2

[_' I WARNING: OVERFILLING OIL CRANKCASE MAY t
CAUSE SERIOUS PERSONAL INJURY. Check and
maintain the proper oil level in the crank case; it is
important and cannot be overemphasized, Check the oi
before each use and change it as needed. See
Changing the Oil,
RECOMMENDED OIL TYPE
Using the proper type and weight of oil in the crankcase is
extremely important. Check the oil before each use and change
the oil regularly. Failure to use the correct oil, or using dirty oil, can
cause premature engine wear and failure.
Use a high-quality SAE 30 weight oil of API (American Petroleum
Institute) service class SF, SG, SH.
ADDING OIL TO CRANKCASE: INITIAL USE
NOTE: This unit is shipped without oil. In order to avoid damage
to the unit, put oil in the crankcase before you attempt to
start the unit.
NOTE: Save the empty oil bottle. It _'_JF \
can be used to measure the Funnel
correct amount during future _pout
oil changes, See Changing the
Oil.
Your unit is supplied with one 3.04
fluid oz. (90 ml.) bottle of SAE 30 SF,
SG, SH oil (Fig. 3).
Fig. 3
1. Unscrew the top of the bottle of
oil and remove the paper seal Oil Fill Plug ___
covering the opening. Replace ---_ __
the top. Next, cut the tip off the - ,rig
funnel spout (Fig. 3). OR ___
2. Tip unit so that the back of the Oil Fill Hole-Y_
engine is facing up in a vertical
position.
3. Remove the oil fill plug from the Fig. 4
crankcase (Fig. 4).
4. Pour the entire bottle of oil into
the oil fill hole (Fig. 5).
NOTE: Never add oil to the fuel or
fuel tank.
Fig. 5
5. Wipe up any oil that may have
spilled and reinstall the oil fill
plug.
Check oil before each use and
change as needed. Refer to
Checking the Oil Level.
RECOMMENDED FUEL TYPE
Old fuel is the primary reason for improper unit performance. Be
sure to use fresh, clean, unleaded gasoline. Dispose of the old
gasoline in accordance to Federal, State and Local regulations.
NOTE: This is a four cycle engine. In order to avoid damage to the
unit, do not mix oil with gasoline.
Definition of Blended Fuels
Today's fuels are often a blend of gasoline and oxygenates such as
ethanol, methanol or MTBE (ether). Alcohol-blended fuel absorbs
water. As little as 1% water in the fuel can form acids when stored.
Use fresh fuel (less than 60 days old), when using alcohol-blended
fuel.
Using Blended Fuels
If you choose to use a blended fuel, or its use is unavoidable,
follow recommended precautions:
• Always use fresh unleaded gasoline
• Use a gas stabilizer fuel additive
• Drain tank and run the engine dry before storing unit
Using Fuel Additives
The use of a gas stabilizer will inhibit corrosion and minimize the
formation of gum deposits. Using a fuel additive can keep fuel from
forming harmful deposits in the carburetor for up to six (6) months.
Add 0.8 oz. (23 ml.) of fuel additive per gallon of fuel according to
the instructions on the fuel additive container. NEVER add fuel
additives directly to the unit's gas tank.
WARNING: Add fuel in a clean, well ventilated
outdoor area. Wipe up any spilled fuel immediately.
Avoid creating a source of ignition for spilt fuel. Do not
start the engine until fuel vapors dissipate.
WARNING: Gasoline is extremely flammable. Ignited
vapors may explode. Always stop the engine and allow
it to cool before filling the fuel tank. Do not smoke while
filling the tank. Keep sparks and open flames at a
distance from the area.
FUELING THE UNIT
WARNING: Remove fuel cap slowly to avoid injury
from fuel spray. Never operate the unit without the fuel
cap securely in place.
GasCanSpout. J'4 Fuel Cap
FuelTank
Fig. 6
1. Remove the fuel cap (Fig, 6).
2. Place the gas container's spout into the fill hole on the fuel
tank (Fig. 6) and fill the tank.
NOTE: Do not overfill the tank,
3. Wipe up any gasoline that may have spilled,
4. Reinstall the fuel cap,
5. Move the unit at least 30 ft, (9,1 m) from the fueling source and
site before starting the engine,

_1 ARNING: Operate this unit only in a well-ventilated
outdoor area. Carbon monoxide exhaust fumes can be
lethal in a confined area.
'_1 WARNING: Avoid accidental starting. Make sure you
are in the starting position when pulling the starter rope I
(Fig. 8). To avoid serious injury, the operator and unit must
be in a stable position while starting.
STARTING INSTRUCTIONS
1. Check the oil level in the crankcase. Refer to
Checking the Oil Level.
2. Fill the fuel tank with fresh, clean unleaded gasoline.
Refer to Fueling the Unit.
NOTE: There is no need to turn the unit on. The On/Off
Stop Control is in the ON ( I ) position at all
times.
3. Fully press and release the primer bulb 10 times,
slowly. Some amount of fuel should be visible in
the primer bulb and fuel lines (Fig. 7). Ifyou can't
see fuel in the bulb, press and release the bulb as
many times as it takes before you can see fuel in it.
COLD UNIT START
4. Place the choke lever in Position 1 (Fig. 7).
5. Crouch in the starting position (Fig. 8). While
squeezing the throttle control, pull the starter rope
out with a slow and steady motion 5 times.
6. Place the choke lever in Position 2 (Fig. 7).
7. While squeezing the throttle control, pull the starter
rope out with a slow and steady motion 1 to 4 times
to start the engine.
8. Keep the throttle squeezed and allow the engine to
warm up for 15 to 30 seconds.
9. Place the choke lever in Position 3 (Fig. 7). The unit
is ready for use.
............IF...The engine does not start, go back to step 3.
IF...The engine fails to start after a few attempts, place
the choke lever in Position 3 and squeeze the
throttle control. Pull the starter rope out with a slow
and steady motion 3 to 8 times, the engine should
start. If not, pull 3 to 8 more times.
WARM UNIT RESTART... If the unit is already hot, place
the choke lever in Position 1. While squeezing the
throttle control, pull the starter rope to restart. Place
the choke lever in Position 3.
NOTE: The unit uses the Incredi-PulF Mstarting system
with MAX FIRE IGNITION TM ,which significantly
reduces the effort required to start the engine.
You must pull the starter rope out far enough to
hear the engine attempt to start. There is no
need to pull the rope briskly-- there is no harsh
resistance when pulling. Be aware that this
starting method is vastly different from (and
much easier than) what you may be used to.
STOPPING INSTRUCTIONS
1. Release your hand from the throttle control. Allow the engine to
cool down by idling.
2. Press and hold On/Off Stop Control in the OFF (O)position until
engine comes to a complete stop (Fig. 9)
Choke Lever Primer Bulb
Fig. 7
Starter Rope
Throttle Control
Fig. 8
Start/On (I)
Throttle Control
Fig. g

WARNING:Alwaysweareye,hearing,footandbody
protectiontoreducetheriskofinjurywhenoperating
thisunit.
HOLDING THE TRIMMER
Before operating the unit, stand in the
operating position (Fig. 10). Check for the
following:
•The operator is wearing eye protection and
proper clothing
• With a slightly-bent right arm, the
operator's right hand is holding the shaft
grip
• The operator's left arm is straight, the left
hand holding the handle
• The unit is at waist level
• The cutting attachment is parallel to the
ground and easily contacts the grass
without the need to bend over Fig. 10
BUMP KNOB LINE ADVANCE
Tap the bump knob on the ground to advance the cutting line when
necessary.
TIPS FOR BEST TRIMMING RESULTS
• For best trimming results, operate unit with throttle control fully
squeezed.
• Keep the cutting attachment parallel to the ground.
• Do not force the cutting attachment. Allow the tip of the line to
do the cutting, especially along walls. Cutting with more than the
tip will reduce cutting efficiency and may overload the engine.
• Cut grass over 8 inches (200 mm) by working from top to bottom
in small increments to avoid premature line wear or engine drag.
• Cut from right to left.
• Slowly move the trimmer into and out of the cutting area at the
desired height. Move either in a forward-backward or side-to-
side motion. Cutting shorter lengths produces the best results.
• Trim only when grass and weeds are dry.
• The life of your cutting line is dependent upon:
- Proper adherence of explained trimming techniques
- What vegetation is cut
- Where vegetation is cut
For example, the line will wear faster when trimming against a
foundation wall as opposed to trimming around a tree. It is normal for
some line breakage to occur from regular use.
DECORATIVE TRIMMING
Decorative trimming is accomplished by removing all vegetation
around trees, posts, fences and more.
Rotate the whole unit so that the cutting attachment is at a 30 °
angle to the ground (Fig. 11).
30 °
Fig. 11

LINEINSTALLATIONFORTHERAPIDREWINDTM CUTTING HEAD
I_I WARNING: Neverusemetal-reinforcedline,wire,chain
or rope. These can break oft and become dangerous
Always use Craftsman XTRA QUIET TM 0.095 inch (2.413 ram)
original equipment manufacturer replacement line. Lines other than
the specified may make the engine overheat or fail.
There are two methods to replace the Rapid Rewind TM trimming line:
•Wind the inner reel with new line
• Instal] a pre-wound inner reel
Winding the Inner Reel With New Line
NOTE: It Is unnecessary to remove the bump knob to instal] a new
trimming line.
1. Cut two 7 ft (2.1 m) pieces of 0.095-inch (2.413 mm) trimming line.
NOTE: Always use the correct line length when installing trimming
line on the unit. The line may not release properly if the line is
too long.
2. Hold the outer spool and turn the inner reel counterclockwise to
line up the arrows on the outer spool and inner reel (Fig. 12).
Top View Of The Rapid Rewind TM
Ou_r
Spool
Arrows
Locking __
Hole
Locking
Hole
J
Line LockingHole
Fig. 14
Fig. 15
piece of line.
8. Hold the outer spool. Wind the inner reel counterclockwise until
approximately four (4) inches (102 mm) of line remain (Fig. 16).
Avoid contact of bump knob while winding. Ensure bump knob is
Reel Bump
Knob
Fig. 12
3. Detach old line ends from locking holes (Fig. 12) and pull old line
out through reel eyelets (Fig. 13).
Trimming Line
Eyelet
Line Loading Hole
Fig. 16
tight on shaft before proceeding, turn bump knob clockwise to
tighten.
9. If winding the line becomes difficult or if the line jams, pull the ends
Fig. 13
4. Making sure arrows are aligned, insert the end of a piece of trimming
line straight into one of the two eyelets inthe outer spool. Push it up
through the lineloading hole in the inner reel (Fig. 13). Do not bend the
linewhen inserting it into the eyelet.
5. Insert the line into the locking hole (Fig. 14). Do not push the line
more than a 1/2 inch (12.7 mm) into the line locking hole. The line
will form a small loop (Fig. 14) when it is inserted correctly.
6. Pull the line from the outer spool until the line is tight against the
inner reel (Fig. 15).
7. Repeat procedures 4-6 with the second piece of line inthe other
eyelet.
NOTE: Do not wind the inner reel before installing the second
Fig. 17
of the line from the spool (Fig. 17). Continue winding the inner reel
counterclockwise until 4 inches of line remains on each side.

CLEANING THE RAPID REWIND TM HEAD
NOTE: Also perform these steps when replacing inner reel with a
new prewound reel.
Cleaning the Rapid Rewind TM may be necessary if:
• A jammed or excessive line must be removed
• The Rapid Rewind TM becomes difficult to wind or does not operate
correctly when bumping the head on the ground.
1. Hold the outer spool, and unscrew the bump knob
counterclockwise (Fig. 18).
3. Pull the inner reel with existing line from the outer spool.
4. If rewinding with new line, remove any existing linefrom the innerreel
before cleaning. Remove any debris or grass from the knob, spring, inner
reeland foam seal.Wash the inner reel with warm soapy water (Fig.20).
Inner Reel
Fig. 20
5. Clean the shaft and the inner surface of the outer spool. To clean
the shaft underneath the plunger, press down on the plunger (Fig.
21). Remove any dirt or debris from the shaft.
Fig. 18
2. Pull out the bump knob, spring and foam seal (Fig. 19).
Bump Knob
Foam Seal
Spring _
Shaft
Plunger
Inner Reel
Fig. 21
Fig. 19
NOTE: The inner reel must be totally dry before reinstalling it into the
outer spool. Do not lubricate the inner reel or outer spool assembly.
6. Place the cleaned and empty or new prewound inner reel into the
outer spool.
7. Place the bump knob, spring and foam seal onto the inner reel (Fig. 19).
8. Press the bump knob down and tighten clockwise.
9. Install new line in the empty inner reel as described in Line Installation
for the Rapid RewindTM.
•MAINTENANCE SCHEDULE •
Perform these required maintenance procedures at the frequency stated in
the table. These procedures should also be apart of any seasonal tune-up.
NOTE: Some maintenance procedures may require special tools or
skills. If you are unsure about these procedures take your
unit to a Sears or other authorized service dealer.
NOTE: Maintenance, replacement, or repair of the emission
control devices and system may be performed by a Sears
or other authorized service dealer.
In order to assure peak performance of your engine, inspection ofthe
engine exhaust port may be necessary after 50 hours of operation. Ifyou
notice lost RPM, poor performance or general lack of acceleration, this
service may be required. Ifyou feel your engine is in need of this inspection,
refer serviceto aSears or other qualified service dealer for repair. DO NOT
attempt to perform this process yourself as engine damage may resultfrom
contaminants involved in the cleaning process for the port.
[_ [WARNING: To prevent serious injury, never perform ]l
maintenance or repairs with unit running. Always service I
and repair a cool unit. Disconnect the spark plug wire to I
ensure that the unit cannot start.
FREQUENCY MAINTENANCE REQUIRED SEE
Before starting engine Fill fuel tank with fresh fuel Page 6
Check oil Page 11
Every 10 hours Clean and re-oil air filter Page 11
First change at 10 hours Change oil Page 11
At 25 hours/every 25 hours Change oil Page 11
Every 50 hours Clean spark arrestor Page 13
10 hours on new engine Check rocker arm to valve clearance and adjust Page 12
Every 25 hours Check rocker arm to valve clearance and adjust Page 12
Every 25 hours Check spark plug condition and gap Page 13
As necessary Clean the Rapid Rewind TM Head Page 10
10

CHECKINGTHEOILLEVEL
Theimportanceofcheckingandmaintainingtheproperoillevelin
thecrankcasecannotbeoveremphasized.Checkoilbeforeeach
use:
1. Stop the engine and allow oil to drain into the crankcase.
2. Place the engine on an elevated, level surface with the cutting
head shield hanging off the surface to get an accurate oil level
Fig. 22
reading (Fig. 22).
3. Keep dirt, grass clippings and other debris out of the engine.
Clean the area around the dipstick before removing it.
4. Remove the oil fill plug.
5. Look into the oil fill hole, use a flashlight if needed. The oil
should be just touching the innermost thread (Fig. 23).
6. If the oil level is not touching the innermost thread on the oil fill
hole, add a small amount of oil to the oil fill hole and recheck
(Fig. 23). Repeat this procedure until the oil level reaches the
innermost thread on the oil fill hole.
NOTE: Do not overfill the unit.
NOTE: Make sure the O-ring is in place on the oil fill plug when
Max_ilFi"_'_ L in e_ Oil Fill Hole
-- Fig. 23 -- Fig. 24
checking and changing the oil (Fig. 24).
[,_l wARNING: wear gloves to prevent injurywhenhandlingunit.
CHANGING THE OIL
For a new engine, change the oil after the first 10 hours of
operation. Change the oil while
the engine is still warm. The oil
will flow freely and carry away
more impurities.
1. Unplug spark plug boot to
prevent accidental starting.
2. Remove the oil fill plug.
3. Pour the oil out of the oil fill
hole and into a container by
tipping the unit to a vertical
position (Fig. 25). Allow ample
time for complete drainage.
4. Wipe up any oil residue on
the unit and clean up any oil
that may have spilled.
Dispose of the oil according
to Federal, State and local
regulations. Fig. 25
5. Refill the crankcase with
3.04 fluid ounce (90 ml) of SAE 30 SF, SG, SH oil.
NOTE: Use the bottle and spout saved from initial use to measure the
correct amount of oil. The top of the label on the bottle
measures approximately 3.04 ounces (90 ml) (Fig. 26). Check
the level; See Checking the Oil Level. Ifthe level is low, add a
small amount of oil and recheck. Do not overfill (Fig. 26).
i\
Fill L[_
Fig. 26
6. Replace the oil fill plug.
7. Reconnect the spark plug boot.
AIR FILTER MAINTENANCE
turn the unit off and allow it to cool before you clean or
service it.
Cleaning the Air Filter
Clean and re-oil the air filter every 10 hours of operation. It is an
important item to maintain. Failureto maintain your air filter properly can
result in poor performance or can cause permanent damage to your
Air FilterCover
Fig. 27
engine.
1. Open the air filter cover. Push the
tab on the under side of the cover
inward. Then pull the air filter cover
out and up. (Fig. 27).
2. Remove the air filter (Fig. 30).
3. Wash the filter in detergent and
water (Fig. 28). Rinse the filter
thoroughly and allow it to dry.
4. Apply enough clean SAE 30 motor
oil to lightly coat the filter (Fig. 29).
5. Squeeze the filter to spread and
remove excess oil (Fig. 30).
6. Replace the filter (Fig. 27).
NOTE: If the unit is operated without
the air filter, you will
VOID the warranty.
7. Reinstall the air filter cover.
Position the slots on the top
of the air filter cover onto the
tabs at the top of the back
Tab <
Fig. 28
Fig. 29
11

Fig. 30
Air Filter Cover
Air Filter
Back Plate Tabs
__.__Locking Tab
Fig. 31
Fig. 32 Tab
plate (Fig. 31).
will not idle, adjust the idle speed screw as follows:
1. Start the engine and let it run at a high idle for a minute to
warm up. Refer to Starting/Stopping Instructions.
2. Release the throttle trigger and let the engine idle. If the engine
stops, insert a small phillips screwdriver in between the Air
Filter Cover and the Engine Cover (Fig. 33). Turn the idle speed
screw in, clockwise, 1/8 of a turn at a time (as needed) until
the engine idles smoothly•
NOTE: The cutting head should not rotate when the engine idles.
3. If the cutting attachment rotates when the engine idles, turn
the idle speed screw counterclockwise 1/8 of a turn at a time
(as needed), until the head stops turning.
Checking the fuel, cleaning the air filter, and adjusting the idle
speed should solve most engine problems. If not and all of the
following are true:
•the engine will not idle
• the engine hesitates or stalls on acceleration
• there is a loss of engine power
Have the carburetor serviced by a Sears or other qualified service
dealer.
ROCKER ARM CLEARANCE
This requires disassembly of the engine• If you feel unsure or
unqualified to perform this, take the unit to a Sears or other
qualified service dealer
NOTE: Inspect the valve to rocker arm clearance with afeeler gauge after
the first 10 hours of operation and every25 hours of operation.
• The engine must be cold when checking or adjusting the valve
clearance.
!_g[ WARNING: The cutting head may spin during idle speedI
1
adjustments. Wear protective clothing and observe all jl
safety instructions to prevent serious personal injury. Remove
__ Screws
• the cover down until the tab on the air filter backplate
into place in the slot on the air filter cover (Fig. 32)•
IDLE SPEED ADJUSTMENT
The idle speed of the engine is Idle Adjustment Screw
adjustable. An idle adjustment
screw is between the air filter
cover and the engine starter
housing (Fig. 33).
NOTE: Careless adjustments
can seriously damage
your unit. Aside from
the idle speed, only a
Sears or other qualified
service dealer should
make carburetor 2.
adjustments.
1. Check Fuel Fig. 33 3.
Old fuel is usually the reason for idle speed problems. Drain and
[_] WARNING: To prevent seri°us pers°nal injury, make l
sure the cutting attachment has stopped rotating before I 4.
you turn it off and set it down. J 5.
refill the tank with fresh fuel prior to making any adjustments. Refer
to Oil and Fuel Information.
2. Clean Air Filter
The condition of the air filter is important to the operation of the
unit• A dirty air filter will restrict air flow. This is often mistaken for 6.
[_k,l WARNING: The cutting attachment may spin during idle],
speed adjustments. Wear protective clothing and observe I
all safety instructions to prevent serious personal injury. I
an out of adjustment idle. Check the condition of the air filter before
adjusting the idle speed screw. Refer to Air Filter Maintenance.
3. Adjust Idle Speed Screw
If, after checking the fuel and cleaning the air filter, the engine still
View Of The Rear Engine Cover
[I
[I
[I
Fig. 34
Remove
Screws
• This task should be performed inside, in a clean, dust free area.
1. Remove the six (6) screws on the back of the engine cover
with a Flat-head or T-25 Torx screwdriver (Fig. 34).
Disconnect the spark plug wire•
Clean dirt from around the spark
plug. Remove the spark plug from
the cylinder head by turning a 5/8
in. socket counterclockwise.
Remove the engine cover (Fig.
34).
Clean dirt from around the rocker
arm cover• Remove the screw
holding the rocker arm cover with
a large flat blade screwdriver or
Torx T-25 bit (Fig. 35). Remove
the rocker arm cover and gasket.
Rocker
Arm
Cover
Spark X
Plug
Hole
Fig. 35
Pull the starter rope slowly to bring the piston to the top of its
travel, (known as top dead center). Check that:
• The piston is at the top of its travel. Look in the spark plug hole
to view the piston (Fig. 36)
• Both rocker arms move freely, and both valves are closed.
If these statements are not true, repeat step 6.
7. Slide the feeler gauge between the rocker arm and the top of
each valve stem. Measure the clearance between the valve
stem and rocker arm (Fig. 36 & 37). Measure both the intake
and exhaust valves.
12

RockerArms INTAKE Adjusting Nuts
EXHAUST
Feeler Gauge @
S®
Fig. 36
Adjusting Nut
.003-.006 in.
(.076-.152 mm)
Rocker Arm
Fig. 37 Valve Stem
The recommended clearance for both intake and exhaust is .003 -
.006 in. (.076 - 0.152 mm). Use a standard automotive .005 in.
(0.127 mm) feeler gauge. The feeler gauge should slide between
the rocker arm and valve stem with a slight amount of resistance,
without binding. See Figures 36 and 37.
8. If the clearance is not within specification:
a. Turn the adjusting nut using a 5/16 inch (8 mm) wrench or
nut driver (Fig. 37).
• To increase clearance, turn the adjusting nut
counterclockwise.
• To decrease clearance, turn the adjusting nut clockwise.
b. Recheck both clearances, and adjust as necessary.
9. Reinstall the rocker arm cover using a new gasket. Torque the
screw to 20-30 in•lb (2.2-3.4 N•m).
10. Check the spark plug and reinstall. See Replacing the Spark Plug.
[_'J ARNING: Do not sand blast, scrape or clean
electrodes. Grit in the engine could damage the
cylinder.
11. Replace the spark plug wire.
12. Reinstall the engine cover. Check alignment of the cover before
tightening the screws. Tighten screws.
REPLACING THE SPARK PLUG
Use a replacement part number 753-05255 or Champion spark
plug, #RDZ19H. The correct air gap is
0.025 in. (0.635 mm.). Remove the plug I I
after every 25 hours of operation and
check its condition.
1. Stop the engine and allow it to cool. 0.025 in. [- ]
Remove the six (6) screws on the {0.635 ram)
back of the engine cover with a
Flat-head or T-25 Torx screwdriver |
(Fig. 34).
2. Grasp the plug wire firmly and pull _,
the cap from the spark plug. Fig. 38
3. Clean dirt from around the spark plug. Remove the spark plug
from the cylinder head by turning a 5/8 in. socket
counterclockwise.
4. Replace cracked, fouled or dirty spark plug. Set the air gap at
0.025 in. (0.635 mm.) using a feeler gauge (Fig. 38).
5. Install a correctly-gapped spark plug in the cylinder head. Turn
the 5/8 in. socket
clockwise until snug.
If using a torque wrench,
torque to:
110-120 in.•lb. (12.3-13.5
N=rn)
Do not over tighten.
SPARK ARRESTOR
MAINTENANCE
1. Remove the rear
engine cover. See
Rocker Arm
Clearance.
2. With a flat blade
screwdriver or Torx T-
20 bit and a T-25 bit,
remove the screws
_MufflersparkArrestor
ot Screen
r_ T-25
SparckArrreStor //_f_ q_
T-30 Screw
Fig. 39
attaching the spark arrestor diverter to the muffler (Fig. 39).
3. Pull the the spark arrestor diverter out of the muffler. Remove
the spark arrestor diverter.
4. Remove the spark arrestor screen from the spark arrestor
_, JWARNING: To avoid serious personal injury, always J
turn your unit off and allow it to cool before you clean or
service it.
diverter.
5. Clean the spark arrestor screen with a wire brush or replace it.
6. Reinstallthe spark arrestor screen, spark arrestor diverter and
screws.
CLEANING
Use a small brush to clean off the outside of the unit. Do not use
strong detergents. Household cleaners that contain aromatic oils
such as pine and lemon, and solvents such as kerosene, can
damage plastic housing or handle. Wipe off any moisture with a soft
cloth.
STORAGE
• Never store the unit with fuel in the tank where fumes may reach
an open flame or spark.
• Allow the engine to cool before storing.
• Lock up the unit to prevent unauthorized use or damage.
• Store the unit in a dry, well-ventilated area.
• Store the unit out of the reach of children.
LONG TERM STORAGE
1. Drain all gasoline from the gas tank into a container. Do not use
gas that has been stored for more than 60 days. Dispose of the
old gasoline in accordance to Federal, State, and Local
regulations.
2. Start the engine and allow it to run until it stalls. This ensures
that all gasoline has been drained from the carburetor.
3. Allow the engine to cool. Remove the spark plug and put 1 oz.
(30 ml) of high quality motor oil into the cylinder. Pull the starter
rope slowly to distribute the oil. Reinstall the spark plug.
NOTE: Remove the spark plug and drain all of the oil from the
cylinder before attempting to start the trimmer after storage.
4. Change the oil, referring to Changing the Oil. Dispose of the
old oil in accordance to Federal, State and Local regulations.
5. Thoroughly clean the unit and inspect for any loose or
damaged parts. Repair or replace damaged parts and tighten
loose screws, nuts or bolts. The unit is ready for storage.
TRANSPORTING
• Allow the engine to cool before transporting.
• Secure the unit while transporting.
• Drain the gas tank before transporting.
• Tighten gas cap before transporting.
REPLACEMENT LINE
13

CAUSE
Empty fuel tank
Old fuel
Plugged spark arrestor
CAUSE
Air filter is plugged
Improper idle speed
CAUSE
Old fuel
Cutting attachment bound with grass
Plugged spark arrestor
CAUSE
Old fuel
Fouled spark plug
ACTION
Fill fuel tank with fuel
Drain gas tank and add fresh fuel
Clean or replace spark arrestor
ACTION
Replace or clean the air filter
Adjust idle speed
ACTION
Drain gas tank and add fresh fuel
Stop the engine and clean the cutting attachment
Clean or replace spark arrestor
ACTION
Drain gas tank and add fresh fuel
Replace or clean the spark plug
14

EngineType...........................................................................................................................................................................Air-Cooled,4-Cycle
Displacement...........................................................................................................................................................................1.77cu.in.(29cc)
OperatingRPM.........................................................................................................................................................................6,800- 9,800rpm
IdleSpeedRPM.......................................................................................................................................................................3,600- 4,400rpm
IgnitionType...........................................................................................................................................................................................Electronic
IgnitionSwitch..................................................................................................................................................................................RockerSwitch
Valveclearance.......................................................................................................................................................003-.006in.(.076-.152mm))
SparkPlugGap.................................................................................................................................................................0.025inch(0.635mm)
Lubrication.............................................................................................................................................................................................SAE30Oil
CrankcaseOilCapacity.................................................................................................................................................................3.04oz(90ml)
Fuel.........................................................................................................................................................................................................Unleaded
Carburetor........................................................................................................................................................................Diaphragm,All-Position
Starter.........................................................................................................................................................................Incredi-PullTM Auto Rewind
Muffler ....................................................................................................................................................................................... Baffled with Guard
Throttle ................................................................................................................................................................................ Manual Spring Return
Fuel Tank Capacity ......................................................................................................................................................................... 14 oz (414 ml)
Drive Shaft Housing ............................................................................................................................................................................... Steel Tube
Throttle Control .......................................................................................................................................................................... Finger-Tip Trigger
Approximate Unit Weight (No fuel, with handle, shield and cutting head) ..................................................................................... 13.5 Ibs (6 kg)
Cutting Mechanism: ...................................................................................................................................................................... Rapid Rewind TM
Line Spool Diameter: ............................................................................................................................................................. 3 inches (76.2 mm)
Trimming Line Diameter: ................................................................................. Craftsman XTRA QUIET 0.095 inch (2.413 mm) spiral cutting line
Cutting Path Diameter .......................................................................................................................................................... 17 inches (43.18 cm)
* All specifications are based on the latest product information available at the time of printing. We reserve the right to make changes at
any time without notice.
CALIFORNIA /EPA EMISSION CONTROL WARRANTY STATEMENT
Your Warranty Rights and Obligations
The California Air Resources Board, the Environmental Protection Agency, and Sears Brands LLC (Sears) are pleased to explain the
emission control system warranty on your 2007 and later small off-road engine. In California and the 49 states, new small off-road engines
must be designed, built and equipped to meet the state's stringent anti-smog standards. Sears must warrant the emission control system
on your small off-road engine for the periods of time listed below provided there has been no abuse, neglect or improper maintenance of
your small off-road engine.
Your emission control system may include parts such as the carburetor or fuel-injection system, the ignition system, and catalytic converter.
Also included may be hoses, belts, connectors and other emission-related assemblies.
Where a warrantable condition exists, Sears will repair your small off-road engine at no cost to you including diagnosis, parts and labor.
The 2007 and later small off-road engines are warranted for two years. If any emission-related part on your engine is defective, the part will be
repaired or replaced by Sears.
Owners Warranty Responsibilities
As the small off-road engine owner, you are responsible for the performance of the required maintenance listed in your operator's manual.
Sears recommends that you retain all receipts covering maintenance on your small off-road engine, but Sears cannot deny warranty solely
for the lack of receipts or for your failure to ensure the performance of all scheduled maintenance.
• As the small off-road engine owner, you should however be aware that Sears may deny you warranty coverage if your small off-road
engine or a part has failed due to abuse, neglect, improper maintenance or unapproved modifications.
• You are responsible for presenting your small off-road engine to a Sears Authorized Service Center as soon as a problem exists. The
warranty repairs should be completed in a reasonable amount of time, not to exceed 30 days.
If you have any questions regarding your warranty rights and responsibilities, you should call f-800-4-MY-HOME®.
Manufacturer's Warranty Coverage
• The warranty period begins on the date the engine or equipment is delivered to the retail purchaser.
• The manufacturer warrants to the initial owner and each subsequent purchaser, that the engine is free from defects in material and
workmanship which cause the failure of a warranted part for a period of two years.
• Repair or replacement of warranted part will be performed at no charge to the owner at an Authorized Sears Service Center. For the
nearest location please contact Sears at: 1-800-4-MY-HOME®.
• Any warranted part which is not scheduled for replacement, as required maintenance or which is scheduled for only for regular inspection
to the effect of "Repair or Replace as Necessary" is warranted for the warranty period. Any warranted part which is scheduled for
replacement as required maintenance will be warranted for the period of time up to the first scheduled replacement point for that part.
• The owner will not be charged for diagnostic labor which leads to the determination that a warranted part is defective, if the diagnostic
work is performed at an Authorized Sears Service Center.
• The manufacturer is liable for damages to other engine components caused by the failure of a warranted part still under warranty.
• Failures caused by abuse, neglect or improper maintenance are not covered under warranty.
15

• The use of add-on or modified parts can be grounds for disallowing a warranty claim. The manufacturer is not liable to cover failures of
warranted parts caused by the use of add-on or modified parts.
• In order to file a claim, go to your nearest Authorized Sears Service Center. Warranty services or repairs will be provided at all Authorized
Sears Service Centers.
• Any manufacturer approved replacement part may be used in the performance of any warranty maintenance or repair of emission related
parts and will be provided without charge to the owner. Any replacement part that is equivalent in performance or durability may be used
in non-warranty maintenance or repair and will not reduce the warranty obligations of the manufacturer.
Emission Warranty Parts List:
The following components are included in the emission-related warranty of the engine: air filter, carburetor, primer, fuel lines, fuel pick up/fuel
filter, ignition module, spark plug, and muffler. Valves and Cam are additionally included if your engine is a 4-Stroke Model.
CALIFORNIA EVAPORATIVE EMISSION CONTROL WARRANTY STATEMENT
Your Warranty Rights and Obligations
The California Air Resources Board and Sears Brands LLC (Sears) is pleased to explain the evaporative emission control system's warranty
on your 2007 model year and later small off-road (equipment type) engine. In California, new equipment that use small off-engines must be
designed, built, and equipped to meet the State's stringent anti-smog standards Sears must warrant the evaporative emission control
system on your small off-road Lawn & Garden engine for the period listed below provided there has been no abuse, neglect or improper
maintenance of your equipment.
Your evaporative emission control system may include parts such as: carburetors, fuel tanks, fuel lines, fuel caps, valves, canisters, filters,
vapor hoses, clamps, connectors, and other associated components. For engines less than or equal to 80 cc, only the fuel tank is subject
to the evaporative emission control warranty requirements of this section. The displacement of your small off road engine is less than 80 cc.
Manufacturer's Warranty Coverage
This evaporative emission control system is warranted for two years. If any evaporative emission-related part on your equipment is defective,
the part will be repaired or replaced by Sears. Owner's Warranty Responsibilities
• As the small off-road Lawn & Garden engine owner, you are responsible for performance of the required maintenance listed in your owner's
manual. Sears recommends that you retain all receipts covering maintenance on your Lawn & Garden Engine but Sears cannot deny
warranty solely for the lack of receipts.
• As the small off-road Lawn & Garden engine owner, you should however be aware that the Sears may deny you warranty coverage if your
fuel tank has failed due to abuse, neglect, or improper maintenance or unapproved modifications.
• You are responsible for presenting your Lawn & Garden fuel tank to Sears distribution center or service center as soon as the problem
exists. The warranty repairs should be completed in a reasonable amount of time, not to exceed 30 days. If you have a question
regarding your warranty coverage, you should contact Sears at 1-800-4-MY-HOME®.
Defects Warranty Requirements
(a) The warranty period begins on the date the engine or equipment is delivered to an ultimate purchaser.
(b) General Evaporative Emissions Warranty Coverage. The fuel tank must be warranted to the ultimate purchaser and any subsequent
owner that the evaporative emission control system when installed was:
(1) Designed, built, and equipped so as to conform with all applicable regulations; and
(2) Free from defects in materials and workmanship that causes the failure of a warranted part for a period of two years.
(c) The warranty on evaporative emissions-related parts will be interpreted as follows:
(1) Any warranted part that is not scheduled for replacement as required maintenance in the written instructions must be warranted for
the warranty period defined in subsection (b)(2). If any such part fails during the period of warranty coverage, it must be repaired or
replaced by Sears. Any such part repaired or replaced under the warranty must be warranted for a time not less than the remaining
warranty period.
(2) Any warranted part that is scheduled only for regular inspection in the written instructions must be warranted for the warranty
period defined in subsection (b)(2). A statement in such written instructions to the effect of "repair or replace as necessary" will
not reduce the period of warranty coverage. Any such part repaired or replaced under warranty must be warranted for a time not
less than the remaining warranty period.
(3) Any warranted part that is scheduled for replacement as required maintenance in the written instructions must be warranted for the
period of time prior to the first scheduled replacement point for that part. If the part fails prior to the first scheduled replacement, the
part must be repaired or replaced by the Sears. Any such part repaired or replaced under warranty must be warranted for a time not
less than the remainder of the period prior to the first scheduled replacement point for the part.
(4) Repair or replacement of any warranted part under the warranty provisions of this article must be performed at no charge to the
owner at a warranty station.
(5) Not withstanding the provisions of subsection (4) above, warranty services or repairs must be provided at distribution centers that
are franchised to service the subject engines or equipment.
(6) The owner must not be charged for diagnostic labor that leads to the determination that a warranted part is in fact defective,
provided that such diagnostic work is performed at a warranty station.
(7) Throughout the evaporative emission control system's warranty period set out in subsection (b)(2), Sears must maintain a supply of
warranted parts sufficient to meet the expected demand for such parts.
(8) Manufacturer approved replacement parts must be used in the performance of any warranty maintenance or repairs and must be
provided without charge to the owner. Such use will not reduce the warranty obligations of the manufacturer issuing the warranty.
(9) The use of any add-on or modified parts will be grounds for disallowing a warranty claim made in accordance with this article. The
manufacturer issuing the warranty will not be liable under this Article to warrant failures of warranted parts caused by the use of an
add-on or modified part.
(10) Sears shall provide any documents that describe the warranty procedures or policies within five working days of request by the Air
Resources Board. Emission Warranty Parts List
(1) Fuel Tank
Written instructions for the maintenance and use of the evaporative emissions control system by the owner shall be furnished with each
new engine or equipment.
16

17

18

Manual del Operador
RN°
4 Ciclos
WEEDWACKER RECORTADOR A GASOLINA
Model No. 316.791910
INCREDI.PULLJ_TM
UNBELIEVABLE STARTING EASE TM
PRECAUCION: Lea el
manual del operador y siga
todas las advertencias e
instrucciones de seguridad.
•SEGURIDAD
• MONTAJE
• OPERACION
• MANTENIMIENTO
• LISTA DE PARTES
Sears, Roebuck and Co., Hoffman Estates, IL 60179, U.S.A.
Visite nuestro sitio web: www.sears.com/craftsman
769-03535A

INDICE DE CONTENIDOS
Normas para una operaci6n segura ...................... E2
Garantia ............................................ E4
Conozca su unidad ................................... E4
Instrucciones de ensamble ............................. E5
Informaci6n del aceite y del combustible .................. E6
Instrucciones de arranque y apagado .................... E7
Instrucciones de operaci6n ............................. E8
Instrucciones de mantenimiento y reparaci6n ............... E9
Limpieza y almacenamiento ........................... E13
Cuadro de soluci6n de problemas ...................... E14
Especificaciones .................................... E15
Garantia de control de emisiones para California ........... E15
Lista de Piezas ..................................... E19
Llamadas a apoyo al cliente .................. Contraportada
PARACH ISPAS
NOTA: Para los usuarios en tierras forestales de los EE.UU. yen
los estados de California, Maine, Oregon y Washington. Todos
los terrenos forestales de los EE.UU. y el estado de California
(C6digos de Recursos PQblicos 4442 y 4443), Oregon y Washington,
requieren por decreto, que ciertos motores de combusti6n interna
que se hagan funcionar en zonas boscosas y/o zonas cubiertas por
pastizales, esten equipados con un parachispas, que sean
mantenidos en buen estado de funcionamiento o que el motor sea
construido, este equipado y sea mantenido para evitar incendios.
Consulte los reglamentos pertinentes a esos requisitos con las
autoridades estatales o locales. El incumplimiento de esos requisitos
puede responsabilizarle o someterle a la imposici6n de una multa.
Esta unidad fue equipada en la fabrica con un parachispas. Si
requiere sustituci6n,hay una Pantalla Parachispas disponible, Pieza
#753-05297 al contactar el departamento de servicio.
PROPOSICION 65 DE CALIFORNIA
LAS EMISIONES DEL MOTOR DE ESTE PRODUCTO CONTIENEN
SUBSTANCIAS QUlMICAS QUE EL ESTADO DE CALIFORNIA
CONOCE COMO CAUSANTES DECANCER, DEFECTOS DE
NACIMIENTO U OTROS DAI_IOSREPRODUCTIVOS.
Los simbolos de seguridad se utilizan para Ilamar su atenci6n
sobre posibles peligros. Los simbolos de seguridad y sus
explicaciones merecen toda su atenci6n y comprensi6n. Los
simbolos de seguridad no eliminan ningQn peligro por si mismos.
Las instrucciones o advertencias que ofrecen no substituyen las
medidas adecuadas de prevenci6n de accidentes.
SIMBOLO SIGNIFICADO
_l ALERTA DE SEGURIDAD : Indica peligro,
I advertencia o precauci6n. Debe prestar atenci6n para
I evitar sufrir graves lesiones personales. Puede ser
I utilizado junto con otros simbolos o figuras.
PELIGRO :El no obedecer una advertencia de
seguridad puede conducir a que usted u otras personas
sufran graves lesiones. Siga siempre las precauciones de
seguridad para reducir el riesgo de incendio, descarga
electrica y lesiones personales.
ADVERTENCIA :El no seguir una advertencia de
seguridad puede conducir a que usted u otras
personas sufran lesiones. Siga siempre las
precauciones de seguridad para reducir el riesgo de
incendio, descarga electrica y lesiones personales.
PRECAUCION :El no seguir una advertencia de
seguridad puede conducir a da_o patrimonial o a que ustedl
u otras personas sufran lesiones personales. Siga siempre
las precauciones de seguridad para reducir el riesgo de
ncend o, descarga eectr ca yes ones persona es. J
REMARQUE: Le ofrece informaci6n o instrucciones que son
esenciales para la operaci6n o mantenimiento del equipo.
Lea el manual del operador y siga todas las advertencias e
instrucciones de seguridad. De no hacerlo, el operador y/o los
espectadores pueden sufrir graves lesiones.
SI TIENE PREGUNTAS, LLAME AL
1-800-659-5917
• IMPORTANTE INFORMACION DE SEGURIDAD •
LEA TODAS LAS INSTRUCCIONES ANTES DE LA OPERACION
ADVERTENCIA: AJutilizer la unidad, debe observer las
reglas de seguddad. Lea estas instrucciones antes de operar la
unidad afin de garantizar la seguridad del operador y cualquier
transeOnte.Guarde estas instrucciones para uso posterior.
• Lea las instrucciones cuidadosamente. Familiarfcese con los
controles y el uso adecuado de la unidad.
• No opere esta unidad cuando este cansado, enfermo o bajo la
influencia de alcohol, drogas o medicamentos.
• Los ni_os y los adolescentes menores de 15 a_os de edad no
deben usar la unidad. Los adolescentes pueden hacerlo bajo la
supervisi6n de un adulto.
• Todos los dispositivos de protecci6n y los accesorios de seguridad
deben estar instalados adecuadamente antes de operar la unidad.
• Inspeccione la unidad antes de usarla. Reemplace las piezas
da_adas. Verifique si hay fugas de combustible. AsegQrese de que
todos los fijadores esten en su lugar y asegurados. Reemplace las
piezas que esten agrietadas, astilladas o daSadas en cualquier
forma. No opere la unidad con piezas sueltas o daSadas.
• Inspeccione cuidadosamente el Area antes de operar la unidad.
Elimine todos los escombros y los objetos duros o filosos tales
como cristal, alambre, etc.
• Este consciente del riesgo de lesi6n en la cabeza, las manos y los pies.
• No permita ni_os, espectadores ni mascotas en elArea. Los ni_os,
los espectadores y las mascotas deben estar fuera de un radio de 50
pies (15 m.) como minimo; de todas formas los espectadores
correran el riesgo de ser golpeados por objetos lanzados por la
unidad. Se debe exhortar a los espectadores a que usen protecci6n
para los ojos. Si se le acerca alguien apague la unidad de inmediato.
• Use s61olinea de reemplazo del Craftsman XTRA QUIET TM
fabricante original del equipo con un diametro de 0.095 de pulgada
(2.413 mm). Nunca use linea reforzada con metal, alambre o soga.
Se pueden romper y convertirse en proyectiles peligrosos.
• Oprima el control del estrangulador y compruebe que regresa
automaticamente a la posici6n de marcha en vacio. Haga todos
los ajustes o reparaciones antes de usar la unidad.
ADVERTENCIAS DE SEGURIDAD PARA LOS RECORTADORES
A GASOLINA
_I_ ADVERTENCIA: La gasolina es muy inflamable, y sus
gases pueden explotar si se encienden. Tome las
siguientes precauciones:
• Guarde el combustible en envases que hayan sido diser_ados y
aprobados para el almacenamiento de dichos materiales.
• Antes de Ilenar el tanque de combustible, apague siempre el
motor y espere que se enfrie. No retire nunca la tapa del tanque
de combustible ni cargue combustible mientras el motor este
caliente. No opere nunca la unidad sin la tapa del combustible
colocada firmemente en su lugar. Afloje la tapa del combustible
lentamente para disipar la presi6n del tanque.
• Cargue elcombustible en un Areaexterior bien ventilada donde no
haya chispas ni llamas. Quite lentamente la tapa del combustible s61o
despues de apagar el motor. No fume mientras carga el combustible.
Limpie de inmediato todo el combustible que se haya derramado.
• Evite crear una fuente de encendido por combustible derramado.
No arranque el motor hasta que se hayan disipado los vapores
del combustible.
• Aleje la unidad a por Io menos 9,1 m (30 pies), del lugar de
carga de combustible antes de arrancar el motor. No fume,
mantenga las chispas y las llamas abiertas lejos del Area
E2