Creative Play NURSERY STORYTELLERS CHAIR User manual

NURSERY STORYTELLERS
CHAIR
Assembly Instructions
IMPORTANT - If foundation are required support legs will be have been extended 450mm
REF: CP058/NST NURSERY STORYTELLERS CHAIR
pg 1 of 9

REF: CP058/NST NURSERY STORYTELLERS CHAIR
pg 2 of 9
PARTS required
x6 (80mm brass screws) x26 (120mm brass screws)
x4 (40mm brass screws)
*IMPORTANT - if foundations required
additional 450mm included (T4 timber)
If freestanding use angle cleats and
expansion bolts/excalibur bolts to secure
seats onto tarmac
QTY 2 (147mm x 47mm) QTY 2 (120mm x 90mm)
QTY 2 (90mm x 90mm)
T3 T4
T5 QTY 1 (147mm x 22mm) QTY 1 (47mm x 47mm)
T6 T7
QTY 4 (147mm x 47mm) - T1 TIMBERS WILL BE CUT/SHAPED
QTY 2 (147mm x 47mm) QTY 2 (147mm x 47mm)
T1
T2a T2b

x2 (angle cleats/brackets)
OPTIONAL - If installed onto tarmac/concrete
NOT REQUIRED IF SUPPORT POSTS HAVE BEEN EXENDED FOR FOUNDATIONS
x2(40mm brass screws)
PARTS required ...
TOOLS required
REF: CP058/NST NURSERY STORYTELLERS CHAIR
pg 3 of 9
x2
expansion bolts / excalibur bolts
To be used to secrure seats onto tarmac
PLEASE BE AWARE some images shown are of STANDARD
STORYTELLERS CHAIR: All measurements however are specific to the NURSERY STORYTELLERS CHAIR

REF: CP058/NST NURSERY STORYTELLERS CHAIR
SOIL
TIMBER SUPPORT POST
CONCRETE
pg 4 of 9
Foundation Details

If the bench IS pre-assembled JUMP TO STEP
REF: CP058/NST NURSERY STORYTELLERS CHAIR
pg 5 of 9
Assembly Instructions
1
2Attach T1 timbers to T6 timber
Using 40mm brass screws
950mm (start of the curve on the
T1 timber)
- 5mm gap between T1 timbers
8
T1
T1
T1
T1
T2a
T2b
T4
T4
T3
T5
T5
T6
T7
950

REF: CP058/NST NURSERY STORYTELLERS CHAIR
pg 6 of 9
Assembly Instructions
3
4
Assemble the ‘seat’ section
Using 120mm brass screws
View from BELOW
5mm gap between T2 timbers
- Use 4 screws per SLAT ensure they are uniform and
screw into the centre of the T5 timbers
Attach the SEAT to the BACK
Using 120mm brass screws
Outer face of T2 timbers & T1 timbers
are flush/level with each other
T2a
T5
T5
T2a
T2b
T2b

REF: CP058/NST NURSERY STORYTELLERS CHAIR
pg 7 of 9
Assembly Instructions
5Attach T4 timbers
Using 120mm brass screws
6Screw T3 timbers to the T4 timbers (arm rests)
Using 80mm & 120mm brass screws
T4 timbers sit in the T2a
‘CUT-OUTS’
Arm rests sit
against the
T1 timbers
Screw as shown above
80mm brass screw
120mm brass screw
*Bottom of T4 timbers are
level with the T1 timbers
If extended for concrete
foundations allow additional
450mm
T4 T1
350
503

REF: CP058/NST NURSERY STORYTELLERS CHAIR
pg 8 of 9
Assembly Instructions
7
8
Screw T7 timber to the T1 timbers
Using 80mm brass screws
Sits between the ARM RESTS
T4 timbers will have
been extended if concrete
foundations required
Install the ASSEMBLED BENCH
Using ANGLE CLEATS with 40mm brass screws and EXPANSION BOLTS or CONCRETE INTO
GROUND as per foundation drawings
Position angle cleats on the INSIDE of
each SUPPORT
- Use 40mm brass screws to attach
angle cleat to the support legs
- Use expansion bolts or EXCALIBUR
bolts to secure the bolts to the concrete
/ tarmac
Follow the FOUNDATION DETAILS on
Page 4
OR

CUT-OUT OPTION
The CUT-OUT option is identical to the ‘standard’ version
The T1 timbers have had SIMPLE circles and 1 x STAR ecut out
REF: CP058/NST NURSERY STORYTELLERS CHAIR
pg 9 of 9
CUT-OUT OPTION AVAILABLE