Creative Playthings 63081-102 User manual

Ice Cream Stand Model:
63081-102
SPECIAL NOTES AND INSTRUCTIONS
The addition of the Ice Cream Stand to a
Creative Playthings gym will increase the
safe play zone requirements of the gym.
Please review the instructions and man-
ual provided with the gym for safety infor-
mation and instructions on proper ground
cover.
All hardware on this set is specially
coated for corrosion resistance. If non-
Creative Playthings hardware is used,
it must be galvanized or stainless steel.
Usage:
The Ice Cream Stand is designed to t on the end of the Lexington and
Williamsburg gyms, below the open end of the roof or tent. It will also t
below the end of the clubhouse on the Yorktown and Ridgeeld gyms
(see exceptions below). The Ice Cream Stand will also t on the end of
the Skybox.
The Ice Cream Stand is not built to t on the side, under the eaves, of
the Williamsburg gym.
IMPORTANT!
If the Ice Cream Stand is to be installed on a
Ridgeeld or Yorktown gym DO NOT mount
a Rock Climber, Chain Climber, or Pinnacle
Rock Wall next to the Ice Cream Stand. There
is potential for head entrapment or other
conict if any of these climbers are directly
adjacent to the Ice Cream Stand. There is
potential for serious injury or death!
No Rock Wall next to
Ice Cream Stand
No Chain Climber next to
Ice Cream Stand
No Pinnacle next to Ice
Cream Stand

Ice Cream Stand Instructions - 19930-100L (08/20)
Copyright 2016, Creative Playthings - Printed in U.S.A. Page 2Page 2
50552-700 Ice Cream Stand Fasteners
17 12002-206 Flat Washer 5/16"
11 12017-206 Lock Washer 5/16"
11 17001-105 Weld Nut 5/16"
11 17003-811 Hex Bolt 5/16 x 2"
4 17036-1202 Lag Screw 5/16 x 3"
2 17036-1802 Lag Screw 5/16 x 4-1/2"
95 17020-115 Screw #10 x 1-5/8"
18 17020-113 Screw #10 x 2-1/2"
4 17020-110 Screw #10 x 3"
15 15081-704 1" Hole Cap, Brown
50553-700 Chalkboard Hardware
4 17020-115 Screw #10 x 1-5/8"
2 17128-305 Pan Head Screw #12 x 3/4"
4 17001-104 Weldnut 1/4"
4 12002-205 Flat Washer 1/4"
4 12017-205 Lock Washer 1/4"
4 17003-609 Hex Bolt 1/4 x 1-1/2"
Screw #10 x 2-1/2"
Hex Bolt 5/16 x 2-1/2"
Lag Screw 5/16 x 3"
Lag Screw 5/16 x 4-1/2"
Flat Washer 5/16"
Lock Washer
5/16"
Weld Nut 5/16" 1" Hole Cap
Screw #10 x 1-5/8"
Screw #10 x 3"
J 8 35270-102 Short Wall Slat 5/4 x 6 x 21"
K 2 35271-102 Table Support 2 x 4 x 16"
L 1 35272-102 Table Wall Support 2 x 4 x 47-1/4"
M 1 40602-102 2 Board Panel Assembly
N 1 40603-102 4 Board Panel Assembly
1 50552-700 Ice Cream Stand Fasteners
O 2 35257-102 Chalkboard Batten 5/4 x 4 x 15"
P 1 15173-500 Chalkboard 15 x 23"
Q 2 35409-102 Seat Block 2 x 3 x 10"
A 3 32239-102 Table Board 5/4 x 6 x 50"
B 2 35260-102 Post 2 x 4 x 63-7/16"
C 2 35261-102 Rafter 2 x 4 x 27-3/4"
D 2 35262-102 Table Cleat 5/4 x 6 x 8-1/2"
E 1 35263-102 Center Rafter 2 x 3 x 27-3/4"
F 1 35265-102 Left Post Top 2 x 4 x 10-3/4"
G 1 35267-102 Right Post Top 2 x 4 x 10-3/4"
H 2 35268-102 Seat Board 2 x 6 x 55-1/2"
I 2 35269-102 Seat Support 2 x 4 x 26-3/4"
Wooden Parts:
Fasteners:
1/4 x 1-1/2" Hex Bolt
1/4 x 2" Lag Screw
#12 x 3/4" Pan
Head Screw
1/4" Flat
Washer
1/4" Lock
Washer
1/4" Weld
Nut

Ice Cream Stand Instructions - 19930-100L (08/20)
Copyright 2016, Creative Playthings - Printed in U.S.A.
Page 3Page 3
STEP TWO - Drill Posts
Determine the placement of the Ice Cream Stand. On the
Williamsburg and Lexington it must be mounted on the end
of the gym, below the open end of the roof or tent. On the
Ridgeeld or Yorktown, the Ice Cream Stand ts on the end
of the main tower below the gable end of the clubhouse. On
the Skybox, the Ice Cream Stand mounts to the long Posts,
opposite the gym to which the Skybox is mounted.
At the center of the inside face of a gym post drill 1/4" diam-
eter holes 2" deep at 12-1/8" and 24-5/8" from the bottom of
the post. Repeat on the inside face of the adjacent gym post.
STEP THREE - Supports to Gym
Fasten one Seat Support (I) to the lower hole one gym post
using one 5/16 x 3" Lag Screw and one 5/16" Flat Washer
with the counter-bored holes facing toward the center of the
gym as shown.
Fasten one Table Support (K) to the upper hole in the gym
post using one 5/16 x 3" Lag Screw and Flat Washer. Posi-
tion the Table Support so the counter-bored holes face in-
ward and the two small holes are closer to the gym post.
Repeat the process, mounting the remaining Seat and Table
Supports to the adjacent gym post.
STEP ONE - Assemble Posts
Fasten the Left Post Top (F) to one Post (B) as shown using
two 5/16 x 2" Hex Bolt Assemblies*. The angles at the top
of the Post and Post Top should match. The Post Top over-
hangs the top of the Post.
* A Hex Bolt Assembly consists of one Hex Bolt, one
Lock Washer, one Flat Washer, and one Weld Nut.
Fasten the Right Post Top (G) to one Post (B) as shown us-
ing two 5/16 x 2" Hex Bolt Assemblies. The angles at the top
of the Post and Post Top should match.
B
F
I
K
G
12-1/8"
24-5/8"
1/4" diameter holes
2" deep
5/16 x 2"
Hex Bolt
5/16 x 3"
Lag Screw
Small holes
align close
to gym

Ice Cream Stand Instructions - 19930-100L (08/20)
Copyright 2016, Creative Playthings - Printed in U.S.A. Page 4Page 4
STEP FOUR - Posts to Supports
Fasten the Post Assemblies to the outside of the Seat and
Table Supports using 5/16 x 2" Hex Bolt Assemblies as
shown at right.
STEP FIVE - Rafters
Fasten the Rafters to the Post Assemblies using 5/16
x 2" Hex Bolt assemblies.
Make sure the Posts are plumb. Rest the angled end
of each Rafter (C) against the adjacent gym post. The
peak of the each rafter should rest approximately 15"
above the top of the platform support (76" above the
ground). Align the inside face of the Rafter with the
inside face of the gym post.
Drill a 1/4" diameter pilot hole 2" deep into each adja-
cent gym post before fastening the Rafters using one
5/16 x 4-1/2" and one Flat Washer each.
STEP SIX - Roof Panels & Center Rafter
Place the 4 Board Panel Assembly (N) on the Rafters, snug
against the gym posts as shown. The cleats on the bottom
of the Panel t between the Rafters. Secure the Panel to the
Rafters using one #10 x 1-5/8" Screw in each hole.
Hold the Center Rafter (E) under the center of the installed
panel with the holes in the Panel aligned with the center
of the Center Rafter. The angled end of the Center Rafter
should align with the top edge of the Panel in the same man-
ner as the Rafters. Secure the Panel to the Center Rafter
using one #10 x 1-5/8" Screw in each hole.
Place the 2 Board Panel Assembly (M) on the Rafters, with
the top edge snug under the bottom edge of the 4 Board
Panel Assembly. The cleats on the bottom of the Panel t
between the Rafters. Secure the Panel to the Rafters using
one#10 x 1-5/8" Screw in each hole.
F
G
C
N
ME
15"
76"
to ground
5/16 x 2"
Hex Bolt
5/16 x 4-1/2"
Lag Screw
#10 x 1-5/8"
Screw
5/16 x 2"
Hex Bolt
1/4" diameter
holes 2" deep

Ice Cream Stand Instructions - 19930-100L (08/20)
Copyright 2016, Creative Playthings - Printed in U.S.A.
Page 5Page 5
STEP SEVEN - Table Wall Support
STEP EIGHT - Short Wall Slats
Secure the Table Wall Support (L) between the two Table
Supports using four #10 x 3" Screws. Send the Screws
through the Holes in the Table Supports and into the holes
in the ends of the Table Wall Support.
Place one Short Wall Slat (J) against the Table Wall Sup-
port and gym Sandbox Side, with the top edge approximately
1" below the top edge of the Table Wall Support. The Slat
should be tight against the right hand Table and Seat Sup-
ports. Fasten the Slat using one #10 x 1-5/8" Screw in each
hole.
Secure another Slat in the same way tight against the left
hand Table and Seat Supports.
Evenly space the six remaining Slats and fasten in the same
way. The gaps will be approximately 3/4".
STEP NINE - Table Boards & Cleat
Fasten the three Table Boards (A) to the Table Supports us-
ing one #10 x 1-5/8" Screw in each hole.
Fasten one Table Cleat (D) to the bottom center of the two
front Table Boards using one #10 x 1-5/8" Screw in each
hole. Be sure not to drive the Screws too deep. The tips of the
Screws must not poke through the top of the Table Boards.
L
J
D
A
Gap 3/4"
(Typical)
1"
#10 x 1-5/8"
Screw
#10 x 1-5/8"
Screw
#10 x 3"
Screw

Ice Cream Stand Instructions - 19930-100L (08/20)
Copyright 2016, Creative Playthings - Printed in U.S.A. Page 6Page 6
STEP TEN - Seat
STEP ELEVEN - Chalkboard
STEP TWELVE - Hole Caps
Rest the Seat Boards (H) on the Seat Supports as shown at
right. Align the holes in the Seat Boards with the center of the
Seat Supports.
Fasten the Seat Boards to the Seat Supports using #10 x
2-1/2" Screws in each hole.
Fasten the remaining Table Cleat (D) to the bottom center of
the Seat Boards using one #10 x 1-5/8" Screw in each hole.
Fasten each Seat Block (Q) to the bottom of the Seat Boards
next to a Seat Support using one #10 x 2-1/2" Screw in
each hole. Make sure the tips of the screws do not protrude
through the top of the seat.
NOTE: one angle brace may be removed from the gym to t the Chalkboard in the position shown.
Hold the Chalkboard (P) against the Post and adjacent gym post at either end of the table. Set the bottom edge approxi-
mately 1" above the table top. Mark the position of the large holes in the Chalkboard on the posts. Drill 1/8" diameter pilot
holes 1" deep at the marks.
Secure the Chalkboard an Chalkboard Battens (O) as shown using four 1/4 x 2" Lag Screws with four 1/4" Flat Washers in
the large holes. Add four #10 x 1-5/8" screws through the smaller holes.
Use two 3/4" Pan Head Screws to secure the Chalkboard to the Battens from behind, though the holes provided.
Perform a nal check to make sure all fasteners have been
tightened.
Locate the 1" Hole Caps in the hardware bag. Install Hole
Caps into all the counter-bored holes to cover the hardware.
D
H
Q
Q
PO
#10 x 2-1/2"
Screw
#10 x 2-1/2"
Screw
#10 x 1-5/8"
Screw
#10 x 1-5/8"
Screw
3/4" Pan
Head Screw
1/4 x 2"
Lag Screw
1/8" diameter
pilot holes
1"