Creative Playthings Lexington Premium Pack 16 User manual

LEXINGTON PREMIUM PACK 16
LEXI9WPP16-100 Rev A (04-18)
© Copyright 2018, Creative Playthings
CHILDHOOD STARTS HERE
LEXI9WPP16
L P P 
• Start by assembling the Lexington tower. Instructions and hard-
ware are in the cartons noted at left. The gym is rotated 90° from
the position shown in the instructions.
The components of this gym can be combined with others to
create different play sets. This is the best order of assembly
to create this specic set.
Read this sheet and all instructions included with the
different parts before assembly.
See the Instructions and Owner's Manual included in carton
63007-445 for important safety information.
Dimensions of assembled package:
27' 9" wide x 15' 7" deep x 12' 9" tall
Cartons for this Play Set:
1 63007-421 Lexington Gym 1 (Hardware)
1 63007-422 Lexington Gym 2
1 63007-423 Lexington Gym 3
1 63007-445 Lexington Roof (Hdwre & Instr)
1 SH946-102 Access Ladder, 5ft
1 AG942-400 Access Ladder Handles (Hdwre & Instr)
1 63058-202 4 Position Swing Beam
1 63060-222 9ft Swing Beam Legs (Hdwre & Instr)
1 50546-777 3 Swings, 1 Trapeze
1 15166-400 10 ft. Super Wave Slide
1 SM964-402 Gable Fans (Hdwre & Instr)
1 SM963-402 Dormer (Hdwre & Instr)
1 AH201-102Q Rock Climbing Wall (Hdwre & Instr)
1 63090-222 Chain Climber Frame
1 63089-606 Chain Cargo Net
1 SC909-800Q Lexington Play Walls
1 SC910-800Q Lexington Play Floor
1 63008-221 Skybox 1 (Hdwre & Instr)
1 63008-222 Skybox 2
1 SJ926-810 Skybox Wood Roof (Hdwre & Instr)
1 8400-202 Spiral Slide, Green (Hardware)
1 63033-102 Spiral Mount (Hdwre & Instr)
1 AG943-400 Slide Handle (Hdwre & Instr)
1 SH304-101Q Pinnacle Rock Wall (Hdwre & Instr)
15 1/2"
7 1/4"
3"
0"
• Wait to install the Access Ladder, Slide, and
Wall Slats until after the rest of the play set is
complete.
• Lex step 2. Omit the sandbox end from the end
of the gym adjacent to the Skybox. It will be
altered to t the Skybox.
• Lex step 7. Do not install the safety rail.
• Lex step 14. Do not install the end wall support
on the Skybox end of the tower.
• Lex step 15. The swing mount isn't needed.
• Lex step 25. Before installing the roof, nd the
post where the swing beam will mount. Drill
7/16" diameter holes through the post at 3",
7-1/4" and 15-1/2" below the top of the post as
shown at right.The beam will be mounted to the
Dormers
front of the post using these holes. Insert one 5/16" weld nut into
the top hole on the inside face of the post. Be sure the threads on
the weld nut are clear, it will be captured by the roof support. Install
the roof.
• Mount the Swing Beam using instructions and hardware includ-
ed in 63060-222. Mount the beam to the previously drilled holes
shown above right rather than the way shown in the instructions.
You may need to temporarily disconnect the roof from the post to
put the beam in place.

© Copyright 2018, Creative Playthings
LEXINGTON PREMIUM PACK 16
LEXI9WPP16-100 Rev A (04-18) Page 2
• Once the roof, roof supports, ridge cap and swing beam
are installed, proceed with the Skybox tower.
• Skybox step 2. Use the method found at the bottom of
page 19 of the Skybox instructions to alter the Lexington
sandbox end and Skybox sandbox sides. Mount them to
the posts.
• Skybox step 11. Use the front posts from The Skybox Roof
(SJ926-810) in place of the post extensions.
• Skybox Step 17. Wait to install the wall slats on the end
where the Spiral Slide will mount, and the side where the
Pinnacle climber will mount until after installing the spiral
and climber.
• Install the Skybox Wood Roof (SJ926-810).
• Install the Play Floor (SC910-800Q).
• Install the Play Walls (SC909-800Q) on the front, back and
swing end of the main tower.
• Install the Gable Fans (SM964-402).
• Using a ladder, install the Dormers (SM963-402) in the
positions shown on the front page of this guide. Ladder
access will be obstructed by later installations.
• Install the Spiral Slide (8400-202) using instructions in-
cluded in 63033-102.
• Mount the Pinnacle Climber to the front of the Skybox in
the position shown.
• Assemble the Rock Climber (AH201-102Q).
• Lean the Access Ladder and Rock Climber as shown
above. Check spacing.
• Secure the access ladder using the method shown in
step 17 of the Lexington instructions. Complete the Rock
Climber installation as instructed in the rock climber man-
ual.
• Fasten Access Ladder Handles (AG942-400) to the Ac-
cess Ladder.
• Assemble the Chain Climber (SH089-917).
• Set the Chain Climber and Super Wave Slide (15166-400)
in place as shown on the front page of this guide. Check
spacing.
• Finish securing the Chain Climber.
• Install the slide mount and slide using the method shown
in steps 23 and 24 of the Lexington instructions.
• Install wall slats in the postions shown in images, using
the methods from the Lexington and Skybox instructions.
Gaps must be narrower than 3-1/2" or wider than 9" to
prevent potential head entrapment.
• Mount one hand grip to the entrance wall slat between
the ladder and the rock climber on the back of the gym.
Mount the other hand grip to the adjacent post at the same
height, using 1/4 x 1-1/2" lag screws and 1/4" at washers.
Drill 3/16" diameter pilot holes for the lag screws.
• Double-check all fasteners are secure and all recessed
hardware is covered by hole caps.
Swing Beam
Spiral Slide
Gable Fan
Rock Climber
Play Walls Chain Climber Pinnacle Climber