Crosley 3977631 User manual

A Note to You....................2
Dryer Safety......................3
Installation
Instructions.......................5
Parts and Features.........13
Using Your Dryer............14
Starting your dryer ......…14
End of cycle signal..........15
Loading...........................15
Selecting the right cycle
and setting......................15
Caring for Your
Dryer ...............................18
Troubleshooting.............20
Assistance or Service....22
Warranty..........................24
1-800-253-1301
Call the Consumer Assistance
Center with questions or
comments.
3977631
120-Volt
Compact
Electric
Dryer
®
www.crosley.com
3977631 v12 c51 3/22/99 5:11 PM Page 1

2
A Note to You
Keep this book and the sales slip together in a safe place for future reference.
It is important for you to save your sales receipt showing the date of
purchase. Proof of purchase will assure you of in-warranty service.
Thank you for buying a CROSLEY®appliance.
To ensure that you enjoy years of trouble-free operation, we developed this Use and Care
Guide. It is full of valuable information about how to operate and maintain your appliance
properly and safely. Please read it carefully.
Also, please complete and mail the Product Registration Card provided with your
appliance. The card helps us notify you about any new information on your appliance.
Please record your model’s information.
Whenever you call to request service for your
appliance, you need to know your complete
model number and serial number. You can
find this information on the model and serial
number label/plate (see the diagram in the
“Parts and Features” section).
Please also record the purchase date of your
appliance and your dealer’s name, address,
and telephone number.
Model Number ______________________
Serial Number ______________________
Purchase Date ______________________
Dealer Name ________________________
Dealer Address ______________________
Dealer Phone ________________________
1-800-253-1301
The Consumer Assistance
Center number is toll free.
3977631 v12 c51 3/22/99 5:11 PM Page 2

3
Dryer Safety
You will be killed or seriously injured
if you don’t follow instructions.
You can be killed or seriously injured
if you don’t follow instructions.
Your safety and the safety of others is very important.
We have provided many important safety messages in this manual and on your appli-
ance. Always read and obey all safety messages.
This is the safety alert symbol.
This symbol alerts you to hazards that can kill or hurt you and others.
All safety messages will be preceded by the safety alert symbol and the
word “DANGER” or “WARNING.” These words mean:
wDANGER
wWARNING
All safety messages will identify the hazard, tell you how to reduce the chance of
injury, and tell you what can happen if the instructions are not followed.
3977631 v12 c51 3/22/99 5:11 PM Page 3

4
DRYER SAFETY
IMPORTANT SAFETY INSTRUCTIONS
WARNING: To reduce the risk of fire, electric shock, or injury to
persons when using the dryer, follow basic precautions, including
the following:
•Read all instructions before
using the dryer.
• Do not place items exposed to
cooking oils in your dryer. Items
contaminated with cooking oils
may contribute to a chemical
reaction that could cause a load
to catch fire.
•Do not dry articles that have
been previously cleaned in,
washed in, soaked in, or spotted
with gasoline, dry-cleaning
solvents, other flammable, or
explosive substances as they
give off vapors that could ignite
or explode.
•Do not allow children to play on
or in the dryer. Close supervision
of children is necessary when
the dryer is used near children.
•Before the dryer is removed from
service or discarded, remove the
door to the drying compartment.
•Do not reach into the dryer if the
drum is moving.
•Do not install or store the dryer
where it will be exposed to the
weather.
•Do not tamper with controls.
•Do not repair or replace any
part of the dryer or attempt any
servicing unless specifically
recommended in this Owner
’ s
Manual or in published user-repair
instructions that you understand
and have the skills to carry out.
•Do not use fabric softeners or
products to eliminate static unless
recommended by the manufacturer
of the fabric softener or product.
•Do not use heat to dry articles
containing foam rubber or similarly
textured rubber-like materials.
•Clean lint screen before or after
each load.
•Keep area around the exhaust
opening and adjacent surrounding
areas free from the accumulation
of lint, dust, and dirt.
•The interior of the dryer and
exhaust vent should be cleaned
periodically by qualified service
personnel.
•See Installation Instructions for
grounding requirements.
SAVE THESE INSTRUCTIONS
IMPORTANT: Observe all governing codes and ordinances.
3977631 v12 c51 3/22/99 5:11 PM Page 4

Installation Instructions
Read the “Dryer Safety” section of your dryer’s Use and Care guide, and completely read
these installation instructions before beginning installation.
Before starting installation
5
•Check location where dryer will be
installed. Proper installation is your
responsibility. The dryer must not be
installed or stored in an area where it will
be exposed to water and/or weather.
Make sure you have everything necessary
for correct installation.
•Grounded electrical supply is required.
See “Electrical requirements.”
•Four-inch metal exhaust vent is
required. See “Exhaust requirements.”
•Check code requirements: Some codes
do not permit or limit installation of clothes
dryers in garages, closets, mobile homes,
or sleeping quarters. Contact your local
building inspector.
•Protection from the weather: Proper
operation of dryer cycles requires
temperatures above 45°F, or the dryer
may not shut off when automatic cycles
are used.
➤
➤
➤
➤
➤
*Height with casters is 321⁄2"
➤
wWARNING
Explosion Hazard
Keep flammable materials and vapors,
such as gasoline, away from dryer.
Place dryer at least 18 inches (46 cm)
above the floor for a garage
installation.
Failure to do so can result in death,
explosion, or fire.
•Support: Floor must be sturdy enough to
support dryer weight and load of 110 lb.
•Location: Must be large enough to fully
open dryer door. See “Recessed area and
closet installation.”
•Level floor: 1 in maximum slope under
entire dryer.
NOTE: Observe all governing codes and
ordinances.
203⁄4"
*31"
237⁄8"
3977631 v12 c51 3/22/99 5:11 PM Page 5

6
INSTALLATION INSTRUCTIONS
Electrical Requirements
WARNING
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can
result in death, fire, or electrical shock.
•A 120-Volt, 60-Hz., AC-only, 15- or 20-
ampere fused electrical supply is required.
•A time-delay fuse or circuit breaker is
recommended. Be sure fuse or circuit
breaker matches the rating of your line.
•Use a separate circuit serving only
your dryer.
•Do not use an extension cord.
GROUNDING INSTRUCTIONS
This appliance must be grounded.
In the event of malfunction or breakdown,
grounding will reduce the risk of electric
shock by providing a path of least
resistance for electric current. This
appliance is equipped with a cord having
an equipment-grounding conductor and a
grounding plug. The power supply cord
must be plugged into an appropriate outlet
that is properly installed and grounded in
accordance with all local codes and
ordinances.
WARNING: Improper connection of the
equipment-grounding conductor can result
in a risk of electric shock.
Check with a qualified electrician or
serviceman if you are in doubt as to
whether the appliance is properly
grounded. Do not modify the plug provided
with the appliance – if it will not fit the
outlet, have a proper outlet installed.
SAVE THESE INSTRUCTIONS
3977631 v12 c51 3/22/99 5:11 PM Page 6

7
INSTALLATION INSTRUCTIONS
How to install your dryer
Now that you’ve unpacked your dryer, check
to be sure you have removed the parts bag
from the drum. Remove the tape that holds
the drum to the cabinet. Move the drum by
hand to make certain all tape has been
removed. Next, wipe the interior of the drum
thoroughly with a damp cloth before using
the dryer.
Installation
For most jobs all you need are a level, duct
tape, an adjustable wrench, and a screw-
driver. All the parts you need are packed in
the appliance. When you take them out,
place them on a cloth so you won’t lose
them. Do not move appliance into the exact
location until the following steps have been
performed.
Installing the cord bracket
•Remove tape from the power cord and the
rear panel
•Insert cord brackets into slotted holes in
rear panel and secure with screws provided
NOTE: Power supply cord may be wrapped
around the brackets for storage convenience
when dryer is not in use.
Parts supplied with the dryer:
1 Cycle and temperature control (timer) knob
1 Push to Start button
4 Casters
2 Cord brackets
2 Screws
Casters
To install the casters, first lay dryer on its
side. Use the carton to prevent damage to
the dryer. Screw casters into dryer base at
four corners and tighten securely. Set dryer
upright. In doing so be careful that dryer
does not roll away from you.
Leveling feet (Part No. 51594200) for use in
permanent installations may be purchased.
See the “Assistance or Service” section.
Cord bracket
Screw
Tools needed
WARNING
Excessive Weight Hazard
Use two or more people to move and
install dryer.
Failure to do so can result in back or
other injury.
3977631 v12 c51 3/22/99 5:11 PM Page 7

8
INSTALLATION INSTRUCTIONS
Exhaust requirements
Your dryer must be properly vented to
achieve maximum drying efficiency.
WARNING: To reduce the risk of fire, this
dryer MUST BE EXHAUSTED OUTDOORS.
•Do not exhaust dryer into a chimney, a wall,
a ceiling, or a concealed space of a building.
•The diameter of the heavy metal vent must
be 4 in.
•Do not use an exhaust hood with a
magnetic latch.
If using an existing exhaust system, remove
accumulated lint.
1. Disconnect vent from the dryer and clean
one section at a time until you reach the
exhaust hood.
2. Use the hose attachment on your
vacuum, or a pole with a feather duster
or rag attached, to clean out lint.
3. Make sure exhaust hood is not plugged
with lint. Be sure the flapper on the
outside end of vent moves freely.
Clean exhaust vent periodically, depending
on use, but at least every 2 years, or when
installing your dryer in a new location.
wWARNING
Fire Hazard
Use a heavy metal vent.
Do not use a plastic vent.
Do not use a metal foil vent.
Failure to follow these instructions
can result in death or fire.
3977631 v12 c51 3/22/99 5:11 PM Page 8

9
Before installing the exhaust system, be
sure to remove the wire exhaust guard that
is located at the exhaust outlet.
Wire exhaust guard
INSTALLATION INSTRUCTIONS
Use duct tape to seal all joints. Do not use
screws to secure vent. Lint may catch on
screws.
Use 4 inch heavy metal vent. Do not kink or
crush flexible metal vent. It must be fully
extended to allow adequate exhaust air to
flow. Check vent after installation.
Use the straightest path possible when
routing the exhaust vent. Use the fewest
number of elbows and turns. Allow as much
room as possible when using elbows or
making turns. Bend vent gradually to avoid
kinking. Remove excess flexible vent to
avoid sagging and kinking that may result in
reduced airflow.
Maximum length of the exhaust system
depends upon the type of vent used,
number of elbows, and the type of exhaust
hood. The maximum length for both heavy
and flexible vent is shown on the next page.
Exhaust outlet at rear of dryer is located as
illustrated. Detailed instructions on spacing
for side and rear clearances can be found in
the “Recessed area and closet installation”
section.
Better Good
Exhaust airflow
12" 4" DIAM
3 1/4"
Rear
exhaust
outlet
3977631 v12 c51 3/22/99 5:11 PM Page 9

4"
Determining vent length
INSTALLATION INSTRUCTIONS
No. of
90°
turns
Rigid Metal Vent 4 in dia
Maximum length
0 36 ft 36 ft 26 ft
1 26 ft 26 ft 16 ft
2 16 ft 16 ft 6 ft
EXHAUST HOOD TYPE
4" 21⁄2"
Flexible Metal Vent 4 in dia
Maximum length
0 28 ft 28 ft 22 ft
1 18 ft 18 ft 12 ft
2 8 ft 8 ft 2 ft
NOTE: Check periodically to ensure that
the outside exhaust hood is not blocked.
The maximum length of the exhaust system
depends upon:
•The type of vent (rigid or flexible metal).
•The number of elbows (90° turns) used.
To determine maximum vent length:
1. See the Exhaust Hood Type chart that
matches your type hood for the maximum
vent lengths you can use.
Do not use vent runs longer than
specified in Exhaust Hood Type chart.
Exhaust systems longer than specified will:
•Shorten the life of the dryer.
•Reduce performance, resulting in
longer drying times and increased
energy usage.
2. Determine the number of elbows you will
need.
3. In the column listing the type of metal vent
you are using (rigid or flexible), find the
maximum length of metal vent on the
same line as the number of elbows.
10
Exhaust hood
Flexible metal vent or
rigid metal vent
Elbow
3977631 v12 c51 3/22/99 5:11 PM Page 10

11
FRONT
STACK STAND
CLOSET
DOOR
SIDE
STACK STAND
DRYER
WASHER
SIDE FRONT
DRYER DRYER
12"
12"
1"
3"
48 sq in
24 sq in
3"
3"
18"
14"
MAX.
1"
1"
3"
†May be 0" clearance.
†† Opening is minimum for closet door. Louvered door with air opening is acceptable.
††† Additional space may be needed for exhaust elbow.
INSTALLATION INSTRUCTIONS
NOTE: Check codes requirements. Some
codes limit or do not permit installation of
clothes dryers in garages, closets, mobile
homes, or sleeping quarters. Contact your
local building inspector.
•This dryer may be installed in a recessed
area or closet. If closet door is installed,
the minimum unobstructed air openings in
top and bottom are required. Louvered
doors with equivalent air openings are
acceptable.
•Your dryer needs a certain amount of
space around it for proper ventilation and
for easier installation and servicing. The
following minimum installation spacings are
required when the unit is to be operated
with or without the Stack Stand Kit. To
purchase a Stack Stand Kit, see the
“Assistance or service” section. For ease of
installation and service, additional spacing
should be considered.
WARNING: To reduce the risk of fire,
this appliance MUST BE EXHAUSTED
OUTDOORS.
NOTE: No fuel-burning appliances may be
installed in the same closet as a dryer.
Recessed area and closet installation
Minimum installation spacing
†
3977631 v12 c51 3/22/99 5:11 PM Page 11

12
INSTALLATION INSTRUCTIONS
Mobile home installation
NOTE: Check codes requirements. Some
codes limit or do not permit installation of
clothes dryers in garages, closets, mobile
homes, or sleeping quarters. Contact your
local building inspector.
• The exhaust vent must be securely
fastened to a non-combustible portion of
the mobile home structure and must not
terminate beneath the mobile home.
• The dryer exhaust vent must not be
connected or secured with screw or other
devices which extend into the interior of
the vent.
• A kit is available to fasten the dryer
securely when the mobile home is in
transit. To purchase a kit, see the
"Assistance or Service" section. Your
dryer does not need to be secured when
the mobile home is not in transit.
Outside wall
Enclosure
Floor
3977631 v12 c51 3/22/99 5:11 PM Page 12

13
Parts and Features
Start button
(p. 14)
Dryer drum
Model and
serial
number label
(p. 2)
Cycle and
temperature
control knob
(p. 16)
Lint screen
(p. 18)
Moisture
sensor
pad
Optional mounting kits
You can mount your compact dryer above your
compact washer using one of the following:
•Stack Kit for free-standing installation.
Part No. 49921
•Stack Kit to mount dryer permanently onto
the washer.
Part No. 3390175
•Dryer Wall-Mounting Kit for securing the
dryer to the wall with a steel bracket.
Part No. 345994
NOTE: The wall must be strong enough to
support the dryer’s weight. (Do not use in
mobile homes.)
3977631 v12 c51 3/22/99 5:11 PM Page 13

Using Your Dryer
wWARNING
Fire Hazard
No washer can completely
remove oil.
Do not dry anything that has ever
had any type of oil on it (including
cooking oils).
Items containing foam, rubber,
or plastic must be dried on a
clothesline or by using an Air Cycle.
Failure to follow these instructions
can result in death or fire.
14
WARNING
Explosion Hazard
Keep flammable materials and vapors,
such as gasoline, away from dryer.
Do not dry anything that has ever had
anything flammable on it (even after
washing).
Failure to follow these instructions can
result in death, explosion, or fire.
Starting your dryer
Before using your dryer, wipe the dryer
drum with a damp cloth to remove dust from
storing and shipping.
1. Load clothes into the dryer and close
the door.
2. Turn the Cycle and Temperature Control
knob either way to the desired cycle. Use
the Energy Preferred Automatic Setting
to dry most loads (see page 16).
3. Push the Start button.
NOTE: Your dryer stops automatically
when a cycle ends.
Stopping and restarting your
dryer
You can stop your dryer anytime during a
program.
To stop your dryer:
Open the dryer door or turn the Cycle and
Temperature Control knob to OFF.
NOTE: The Cycle and Temperature Control
knob should point to an Off area when the
dryer is not in use.
To restart your dryer:
Close the door, select a new cycle and
temperature (if desired), and push the Start
button.
3977631 v12 c51 3/22/99 5:11 PM Page 14

Drying tips
•Always follow care label directions when
they are available.
•Always use fabric softener sheets labeled
as dryer safe and follow package
instructions carefully.
•Remove the load from the dryer as soon
as tumbling stops to reduce wrinkling.
This is especially important for permanent
press, knits, and synthetic fabrics.
15
USING YOUR DRYER
Selecting the right cycle and setting
The following pages describe the cycles on
your dryer. Refer to the chart on page 17 for
help in selecting drying cycles.
Cycle and temperature tips
•Make sure you have selected the
correct cycle and temperature for your
load.
•Use the Air cycle, or line dry rubber,
plastic, delicate, and heat-sensitive fabrics
•The last few minutes of all cycles are
without heat to make the load cooler to
handle.
Loading
Loading suggestions
This table shows the maximum load you
can place in your compact dryer. Expect
longer drying times.
COMPACT DRYERS
Permanent Press
6 shirts
– or –
2 double sheets
2 pillowcases
– or –
2 single sheets
2 pillowcases
Knits
2 slacks
2 shirts
– or –
3 dresses
Delicates
1 camisole
2 slips
2 panties
2 bras
1 nightie
1 half slip
Mixed Load
1 pair slacks
2 pillowcases
2 shirts
1 T-shirt
Heavy Work Clothes
3 work shirts
2 pair pants
Towels
9 bath towels
– or –
6 bath towels
3 hand towels
6 wash cloths
End of cycle signal
The dryer sounds a signal to let you know
when the cycle is finished. The signal is not
adjustable and cannot be turned off.
The signal is helpful when you are drying
permanent press, synthetics, and other
items that should be taken out as soon as
the dryer stops.
3977631 v12 c51 3/22/99 5:11 PM Page 15

Automatic Permanent Press/
Regular Cycle
Dry most loads using the Energy
Preferred Automatic Setting. Your
Automatic cycle shuts off when the selected
dryness is reached. The Cycle and
Temperature Control knob will not move until
the load is almost dry. After the cool-down,
the knob automatically turns to an Off area
and tumbling stops.
•If the load is drier than you like, select a
setting closer to LESS the next time you
dry a similar load.
•If the load is not as dry as you like,
complete drying using a Timed cycle.
Select a setting closer to MORE the next
time you dry a similar load.
Timed Dry cycle
Use a Timed Drying cycle to complete
drying if some items are damp after
Automatic drying. Timed drying is also
useful for:
•Delicate items and small loads that need
a short drying time.
•Bulky items and large loads that require
a long drying time.
For a damp dry, turn the Cycle and
Temperature Control knob to 30 min. or less.
Air cycle
The Air cycle has no heat. Use this
unheated cycle to fluff or air dry bedding,
plastic tablecloths, foam pillows, sneakers,
etc. See page 17 for more information about
the Air cycle.
16
USING YOUR DRYER
3977631 v12 c51 3/22/99 5:11 PM Page 16

17
COTTONS AND LINENS
Extra heavy–Bedspreads, mattress pads, quilts
Heavyweight–Towels, jeans, corduroys, work
clothes
Mediumweight–Sheets, cotton underwear,
diapers
Lightweight–Batistes, organdies, lingerie
PERMANENT PRESS, SYNTHETICS AND
BLENDS
Heavyweight–Work clothes, jackets, raincoats
Mediumweight–Shirts, play clothes, sheets,
slacks
Lightweight–Lingerie, blouses, dresses
KNITS
Heavyweight–Cottons, rayons, blends, T-shirts,
slacks, shirts
Mediumweight–Synthetics (polyester, acrylic,
etc.), dress slacks, skirts, sweaters
Lightweight–Synthetics (polyester, acrylic, etc.)
and blends, lingerie, blouses, dresses
DELICATE FABRICS
Sheer curtains (2 or 3 panels), gauze, lace, etc.
RUBBER, PLASTIC, HEAT-SENSITIVE
FABRICS
Foam rubber–Pillows, bras, stuffed toys
Plastic–Shower curtains, tablecloths
Rubber-backed rugs
Olefin, Polypropylene, Sheer nylon
COTTON AND CANVAS SHOES
Place several bath towels in the dryer to act as
a buffer. Remove shoes from dryer while still
damp. Stretch shoes and allow to air dry.
TYPE OF LOAD CYCLE
Selecting the right cycle and setting
TIME (minutes)
USING YOUR DRYER
Timed Drying
Perm. Press/Reg.
Perm. Press/Reg.
Perm. Press/Reg.
Perm. Press/Reg.
Perm. Press/Reg.
Perm. Press/Reg.
Perm. Press/Reg.
Perm. Press/Reg.
Perm. Press/Reg.
Air
Air
Air
Air
Air
Air
90-105
†Reset Air cycle as needed to complete drying.
20-30†
20-30†
20-30†
40-50†
15-20†
30-40†
3977631 v12 c51 3/22/99 5:11 PM Page 17

18
Caring for Your Dryer
Cleaning the lint screen
Every load cleaning
The lint screen is located inside the dryer
drum, on the back wall. Clean it before
starting each load. A screen blocked by
lint can increase drying time.
To clean:
1. Open the door and pull the lint screen
straight out.
2. Squeeze body of lint screen lightly while
pulling the cover off.
3. Roll lint off the screen with your fingers.
Do not rinse or wash screen to remove
lint. Wet lint is hard to remove.
4. Replace cover on lint screen body. Push
the lint screen firmly back into place and
close the door.
IMPORTANT:
•Do not run the dryer with the lint screen
loose, damaged, blocked, or missing.
Doing so can cause overheating and
damage to both the dryer and fabrics.
•Some towels made of synthetic fibers and
natural fibers (polyester and cotton blends)
may shed more lint than other towels,
causing your dryer’s lint screen to fill up
faster. Be sure to remove lint from the lint
screen before and after drying new towels.
As needed cleaning
Laundry detergents and fabric softeners can
cause a residue buildup on the lint screen.
Clean the lint screen with a nylon brush
every six months or more frequently if it
becomes clogged due to a residue buildup.
Use the following method:
1. Wet both sides of lint screen with hot
water.
2. Wet a nylon brush with hot water and
liquid detergent; scrub lint
screen with the brush to
remove residue buildup.
3. Rinse screen with hot water.
4. Thoroughly dry lint screen with a clean
towel. Replace in dryer.
3977631 v12 c51 3/22/99 5:11 PM Page 18

19
Cleaning the dryer interior
Garments which contain unstable dyes,
such as denim blue jeans or brightly
colored cotton items, may discolor the
dryer interior. These stains are not harmful
to your dryer and will not stain future loads
of clothes. It is helpful to dry unstable dye
items inside out to prevent dye transfer.
To clean dryer drum:
1. Make a paste with powdered laundry
detergent and very warm water.
2. Apply paste to a soft cloth.
OR
Apply a liquid, non-flammable household
cleaner to the stained area
and rub with a soft cloth until
all excess dye is removed.
3. Wipe drum thoroughly with a damp cloth.
4. Tumble a load of clean cloths or towels to
dry drum.
WARNING
Explosion Hazard
Use nonflammable cleaner.
Failure to do so can result in death,
explosion, or fire.
Removing accumulated lint from inside
the dryer cabinet
Lint should be removed every two to
three years, or more often, depending on
dryer usage. Cleaning should be done by
a qualified person.
USING YOUR DRYER
3977631 v12 c51 3/22/99 5:11 PM Page 19

20
Troubleshooting
Common drying problems
PROBLEM
Not drying
satisfactorily
Dryer will
not run
CAUSE
• The compact dryer operates at
a lower wattage.
• Exhaust opening is blocked.
• Lint screen is clogged with lint.
• Restricted air movement.
Exhaust vent or outside exhaust
hood is clogged with lint.
• Exhaust vent is crushed or
kinked.
• Cycle and Temperature Control
knob is set on Air dry.
• Load not contacting the
moisture sensor pad and
automatic cycle ending early.
• Fabric softener sheets blocking
exhaust grill.
• Dryer located in room with
temperature below 45ºF.
• Large amount of moisture in
the load.
• Cold rinse water used.
• Load too large and bulky to dry
quickly.
• Power cord not firmly plugged
into a live circuit with proper
voltage.
• Fuse blown or circuit breaker
tripped.
• Using a regular fuse.
• Dryer door not firmly closed.
• Start button not firmly pressed.
• Cycle and Temperature Control
knob set to Off.
SOLUTION
• Expect longer drying times.
• Keep area around exhaust opening
clear.
• Clean lint screen.
• Run dryer for 5-10 minutes. Hold
hand under outside exhaust hood to
check air movement. If you do not
feel air moving, clean exhaust system
of lint or replace exhaust vent with
heavy metal or flexible metal vent
(see “Installation Instructions”).
• Replace with heavy metal or flexible
metal vent (see your Installation
Instructions).
• Select the right cycle and for the
types of garments being dried (see
“Using your Dryer”).
• Level dryer (see your Installation
Instructions).
• Use only one softener sheet per
load and only use it once.
• Move dryer to a location with
temperatures above 45ºF.
• Expect longer dry times with items
that hold more moisture (cottons).
• Expect longer dry times.
• Separate load to tumble freely.
• Plug power cord into a live circuit.
• Replace fuse or reset breaker.
• Replace with a time-delay fuse.
• Close dryer door tightly.
• Press Start button again.
• Set knob to a cycle or time.
3977631 v12 c51 3/22/99 5:11 PM Page 20