Croydex CONSTANCE Manual

SAFETY & PRODUCT CARE
1. To retain the best quality finish, clean product with a soft cloth and a mild soap solution.
2. DO NOT use abrasive or chemical cleaners as they may damage the surface of the toilet seat or hinges.
3. Spray cleaning liquids onto the cloth and not directly onto the product.
4. DO NOT force the seat down as this can cause damage to the product and its function.
5. Take care when cleaning the toilet pan with chemical cleaners. Avoid contact of the chemical cleaners
with the toilet seat or hinges. Immediately rinse o any splashes to avoid damage or discolouration to the
surface of the toilet seat and hinge parts.
TS 074 R04
AB
CD
E
F
x2 x2
x2 x2
x2
x2
Gx2
H J x2
I
K
CHROME CAP
SUPPORT COVER NUT KEY BOLT
FLEXI FIX BRACKET HEX KEY CONICAL
WASHER
WASHER
NUT
SPACER
RUBBER PLUG
1
CONSTANCE / MICHIGAN
SOFT CLOSE & QUICK RELEASE TOILET SEAT
Always follow the instructions provided to ensure that your product is assembled and
fitted safely, and retains its high quality finish.
ALWAYS RETAIN THIS MANUAL FOR FUTURE REFERENCE
ALL PRODUCT DIMENSIONS DETAILED IN THIS
INSTALLATION AND MAINTENANCE MANUAL ARE
APPROXIMATE
ALL ILLUSTRATIONS OF THE PRODUCT ARE FOR
REFERENCE ONLY. COMPONENTS SUPPLIED WITH
INDIVIDUAL PRODUCTS MAY DIFFER
Tel: [phone]
Email: [e-mail]
Web: www.croydex.com
ALWAYS READ THROUGH AND FULLY UNDERSTAND THE INSTRUCTION
LEAFLET BEFORE STARTING THE INSTALLATION OF THIS PRODUCT.
ALWAYS CHECK THE PACKAGING AND ENSURE YOU HAVE ALL FIXINGS
AND COMPONENT PARTS DETAILED IN THIS INSTRUCTION LEAFLET
BEFORE RECYCLING OR DI0SPOSAL OFTHE PACKAGING.
ALWAYS ENSURE YOU HAVE ALL THE FIXINGS AND COMPONENT PARTS
BEFORE ATTEMPTING TO ASSEMBLE OR FITTHIS PRODUCT.
CONTACT DETAILS
UK: Croydex, Central Way, Andover, Hampshire, SP10 5AW, UK
EU: MIL, Unit 8 Purcellsinch Ind Est, Dublin Road, Kilkenny, R95 HP71, Ireland

PREINSTALLATION
1. Remove the old seat from the pan and clean the surface around the fixing holes.
2. Ensure the surfaces around the fixing holes are completely dry and free of any dust or debris before
beginning the installation.
3. To ensure you do not lose any dropped components in the toilet pan, place cling film over the toilet
bowl.
4. COMPLETE PRE-INSTALLATION STEPS 4, 5 & 6 BEFORE REMOVING THE HYGIENE FILM from the toilet
seat. Position the seat overyour pan to ensure the shape and profile of the toilet seat matches your
toilet pan. (See Fig. 1)
5. Align the front edge of the toilet seat with the front ofyour toilet pan. Hold your hand at the back of
the toilet seat and using it as a pivot, raise the toilet seat. (See Fig. 2)
6. The seat should be able to rest backwards at an angle. If it cannot rest at an angle and can only
rest vertically, the seat WILL NOT function correctly. (See Fig. 3A& 3B)
7. ONLY ONCE YOU ARE SATISFIED THAT THE TOILET SEAT WILL FITYOUR TOILET PAN SHOULD YOU
REMOVE THE HYGIENE FILM.
8. Remove the support covers (C) from the underside of the flexi fix brackets (B) to reveal the adhesive
tape and red protective film. (See Fig. 4) Note: Discard the support cover once removed, it is no
longer required.
9. Carefully peel o the red protective film from the adhesive pad on both flexi fix brackets (B).
(See Fig. 4)
TS 074 R04
2
FLEXI FIX BRACKET
SUPPORT COVER
UNDERSIDE OF
FLEXI FIX BRACKET
Fig 1. Fig 2.
NOTE: THIS STEP IS CRUCIALTO ENSURE
THAT THE LID AND RING ON YOUR TOILET
SEAT DO NOT FALL DOWN DURING USE!
Fig 3A. Fig 3B.
Fig 4.
Note: Discard the support cover once
removed, it is no longer required.
C
B

3.
Lay the seat onto the pillars and rest it on the spacer (K). (See Fig. 8)
fig. 8
TS 074 R04
fig. 7
2.
Slide the spacer onto both pillars. Rotate the Flexi Fix brackets if necessary.
(See Fig. 7)
3
CONICAL
WASHER (E)
MUST FACE
UPWARDS
This installation is designed to be used on ‘standard’
toilets with access below the toilet pan.
CHOOSE BETWEEN
OR
BOTTOM FIX INSTALLATION This installation is designed to be used on ‘back to
wall’ toilets with no access below the toilet pan.
TOP FIX INSTALLATION
Examples ofBottom Fix toilet pans. Examples ofTop Fix toilet pans.
1.Identifyyour toilet pan style. Loosely install the flexi fix bracket (B) through the mounting holes using either bottom fix installation (See Fig. 5) or top fix installation (See Fig. 6). DO NOT
DEPRESS THE BRACKETS,THIS MAY RESULT IN THETAPE STICKING BEFORE YOU ARE SATISFIED
WITH THEIR POSITION.
(Fig. 6)
(Fig. 5)
E
H
G
F
B
JJ
B
D
INNER POSITION
Inner hole positions can be used for this seat.
INSTALLATION
DO NOT FULLY TIGHTEN.
BRACKETS SHOULD BE
ABLE TO MOVE.
DO NOT FULLY TIGHTEN.
BRACKETS SHOULD BE
ABLE TO MOVE.

TS 074 R04
fig. 13
7.
Remove the spacer (K) from the Flexi Fix
Bracket. (See Fig. 13)
fig. 14
8.
Place the chrome caps (A) onto the
brackets.(See Fig. 14)
fig. 16fig. 15
9.
Attach the seat onto the hinges to
complete the installation. You should hear
a click to confirm it is engaged. (See Fig. 15) 10.
To activate the quick release function,
press and hold the button, then lift the
seat away. (See Fig. 16)
Note:
For Constance seat, button located at the front.
For Michigan seat, button located at the back.
4
TOP FIX INSTALLATIONBOTTOM FIX INSTALLATION
6.
Carefully remove the seat without disturbing the bracket positions and fully tighten the screws (J) to
firmly secure the hinge brackets. (See Fig. 11 and 12). Do not to over-tighten.
(Fig. 11) (Fig. 12)
OR
NUT KEY (H)
fig. 9
4.
Align the seat with your toilet pan by
rotating and sliding the Flexi Fix brackets.
If required, lift the seat o the pillars to help
with the adjustment. (See Fig. 9)
BRACKETS SHOULD BE SYMMETRICAL
5.
Once you are confident with the position of
your seat, apply pressure on each Flexi Fix
bracket and collapse the supports.
Hold down for 20 seconds. (See Fig. 10)
fig. 10
HEX KEY (I)
HEX KEY (I)
FULLY TIGHTEN. FULLY TIGHTEN.
20s