Crystal Video FREECAST SW800R User manual

RX: x 1CP03029
Waterproof Case x1 Antenna x2
Antenna x 2Binding Belt x1
TX: x1CP07029 MICRO HDMI
Connector x 2
FORWORD
- Please read this manual carefully before using this product
and retain it properly for future reference.
- If there is any doubt or difficulty in the process of product usage,
please feel free to contact us or the dealer.
- The company reserves the authority to amend the specification.
PACKING LIST
USB Cable
(Standard USB
2.0 male & Mini USB) x1
* Please take all the actual accessories as the standard.
FEATURES
Supports manual channel switching.
Dustpoof and waterproof, up to IP68 (transmitter only).
Perfect environmental adaptability, operating temperature -10~50°C.
Compact and portable design.
The transmitter support Mini-USB power supply.
BRIEF INTRODUCTION
Freecast is designed for live video wireless monitoring for
outdoor sports,outdoor video broadcasting, outdoor photography /
cinematographer.It seamlessly transmits footage captured by
action cameras in big range.It is a compact and portable device
with industrial dust and waterproof design,weighing only 400g.
Freecast supports video browsing via iOS and Android
OS devices. With good channel selection ability and video
encryption,it perfectly fits video transmission requirement
of outdoor applications.
Special wireless video transmission device for action camera.
Adopt High-speed wireless transmission technology,
it features ultra-low latency and long transmission range.
Support up to 3 smartphone clients live stream the footage
simultaneously.
Perfectly compatible with iOS / Android operating system
for real-time monitoring.
H.264 compression technology, high-quality intensive
compression, State-of-art video quality.
TM
11 12
User Manual Model: SW800R Product: FREECAST Receiver

1
2
6
3
7
123
45WIFI Indicator
8
9
10
8
Power Key of transmitter
6
Setting Key of action camera
7Power Key of action camera
5
4
Transmitter
Micro HDMI in Locking buckle
Waterproof front plate 9
10
11
Pairing Key
11
Omnidirectional Antenna Waterproof case rear plate
MECHANIC INFORMATION
1
TX：CP07029
7
6
5
1
4Power Switch
7
Back
Omnidirectional Antenna
Frequency Indicator
RX：CP03029
2
3
4
2Channel Switching & Paring Key 3USB Power Supply Socket
5 6
Front
8
8
8Binding Belt Slot (Holder)
WIFI Indicator
Charging & low battery indicator
1
1
13 14

INSTALLATION
Micro-HDMI Connector
Antenna
CP07029 Transmitter
Action Camera
Battery
1. Mount into the front part of transmitter.
Connect camera interface to transmitter HDMI socket by HDMI cable.
action camera
1
2. Insert lithium battery into the battery bay of transmitter.
(Special notice: ansmitter doesn’t come with lithium battery,
Recommend users to buy lithium batteries.
3. Mount the antenna on the top of transmitter (as picture shows).
2
3
5. Cover waterproof front plate to the front side of transmitter.
4. Cover waterproof rear plate to the rear side of transmitter.
Battery Bay
lithium battery
Metal Button
Press Metal Button to
pull out the battery.
HOW TO PULL OUT
THE BATTERY
Rear Plate of
Waterproof Case
Locking buckle
4
5
6
6
6. Lock up the left and right buckle.
7. Fix the ready transmitter to your desired place by
action camera bracket.
Power Key of transmitter
7
8. Power on action camera.
9. Power on transmitter.
Locking buckle
Front Plate of
Waterproof Case
Installation completed
Power Key of Gopro
Fix the ready transmitter to your
desired place by Gopro bracket.
15 16
TX:CP07029 Installation

12:45 PM 100%
WiFi
Data
Item
Transmitter：CP07029
5150~5250、5725～5850MHz
receiver sensitivity ≤ -87dBm
2x2 MiMO External antenna RPSMA male 50Ωantenna gain 2dBi
IEEE 802.11n
200mS
OS Requirements for
Handheld device iOS 5.0；Android4.0
Basic Functions Support live streaming, taking picture, recording and playback
Support up to 3 smartphone clients live stream the footage simultaneously
Power Supply Built in 3.7V Lithium Battery
Operating Hours Approx 7H
≤1.5W
Receiver：CP03029
90.5mm (W) x 64.5mm (H) x 21.5mm (D)
12:45 PM 100% 12:45 PM 100%
Boot screen
Taking Pictures,
Recording and playback
Smartphone APP
SPECIFICATION
1. Mount the antenna on the top of receiver.
2. Put the binding belt through the slot of receiver
rear side.（Picture 2）
3. Fasten the receiver on arm or other desired
places.（Picture 3）
1
23
4. Search and connect tablet and Smartphone to Wifi AP of receiver
(FREECAST****Password:12345678), after wifi AP connected,
run corresponding App for live streaming, real-time monitoring,
taking picture, recording, playback and other operations.
(as illustration shows)
5. In outdoor operation, you can supply power to the receiver by
USB cable.
Receiver CP03029 Installation
Antenna
Dimensions
Transmission Range
Latency
External antenna interface
and impedance
Frequency
Power Consumption
Temperature
Wireless Standard
Up to 300-500m
-10 °C ~ +50°C（Operating）；-20~+75°C（Storage）
17 18
92mm (W) x 53mm (H) x 21.5mm (D)
Dimensions
Transmission Power 6dBm
Transmission Range Up to 300-500m
Latency 200mS
External antenna interface
and impedance
Frequency 5150~5250、5725~5850MHz
Video Bitrate Constant Bitrate 2Mbps
Resolution 1080P60Hz;720P60Hz
Operating voltage 3.3V-4.2V Lithium Battery Powered
Power Consumption Approx 3W
Temperature -10 °C ~ +50°C（Operating）；-20~+75°C（Storage）
Weight
Waterproof grade IP68
400G (including battery and antenna)
Video Encoding format H.264 image compression
RPSMA male, Impedance 50Ω
IEEE 802.11n
Wireless Standard

Transmission
CP07029
Model LED indicator Indicator Status Status
WIFI indicator (BLU)
Low-Battery
Indicator (RED)
On
Flash Slowly
Flash Rapidly
Blinking
Receiver
CP03029 Frequency indicator
Battery Indicator
Off
Red Indicator blinking
Yellow Indicator off
Yellow Indicator on
Connected
Waiting for connection
Start WPS coding
Low-battery
The number of blinks indicates
the current frequency value
No frequency switching
Low-battery
Battery full
Charging battery
Malfunction Failure Cause Solution
No Picture
The Receiver doesn’t power on
The Receiver doesn’t connected
to APP device
Exception connection between
Signal source and transmitter
Exception of transmitter
Image
Picture is not clear,
with noise and
mosaics
Exception of Receiver
Tx / Rx antenna are not erecte
The distance between Tx and Rx
exceed Effective transmission range
Power on the Receiver
Connecting receiver to APP
device over Wifi
Check up interface channel between
Signal source and transmitter
Restart the transmitter
Restart the Receive
Keep Tx / Rx antenna erect
Move Receiver closer to the transmitter
Reduce the solid walls between Tx and Rx
Move Receiver closer to the transmitter or
skip the obstacles
Solid walls between Tx and Rx
Too many obstacles between Tx and Rx
SPECIAL NOTICE
* Since the product's improving p rocess, all the performance,
design and specifications of ou rproducts are subject to minor
change without prior notice.
INDICATOR DESCRIPTION
WIFI indicator
On
Flash Slowly
Flash Rapidly
Blinking
Connected
Waiting for connection
Start WPS coding
TROUBLE SHOOTING
1.Although the product has provided the function of data encryption when
transmitting, you still need to pay attention to deliberate signal interception.
There will be the Possibility of a third party intentionally intercept the
transmission signal since the product adopt wireless communication.
Please do not use the product on confidential and important communications,
or life-related communications The main concern is that the content of
wireless communication might be received by the third party's wireless
devices deliberately or accidentally
2. The impact of radio waves (such as the following environment may cause
the abnormal audio and video(blocked image, noise ...etc.).
1 ) Transmit near the wall which is hard for the radio waves to get through.
2 ) Quite close to the refrigerator, metal fitment and appliances,
or next to the crowded situation.
3. This product has been tested and manufactured to comply with national
electrical safety rules, however, there will be noise caused by the
interference with other machines in rare cases. If the interference is
happened, please keep a certain distance away from other machines.
4. DO NOT turn the power on before the antennas are properly installed.
5. Please do not set up the transmitter and receiver in metal shelf,
or it will hinder the wireless communications.
6. It will take 15-20 seconds to boot the system before wireless
communication start, the media receiver can not be operated during this time.
iOS Android
19 20

FCC Statement
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to
operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions (1)this device may not
cause harmful interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation