manuals.online logo
Brands
  1. Home
  2. •
  3. Brands
  4. •
  5. CSH
  6. •
  7. Rack & Stand
  8. •
  9. CSH QG.130 Series User manual

CSH QG.130 Series User manual

INSTRUCTION MANUAL
for installing
DOUBLE-HOOK HARDWARE
QG.130 Series
2
Step 1: Rail Installation
Special application notes:
• Leave at least 7” of clearance between the center of the rail and the ceiling, crown
moulding or other overhanging protrusions when the ladder is in the stored position (close to
the wall/cabinet/bookshelf).
• In the climbing position, a minimum 3” clearance between the center of the rail and any
upper cabinet doors is required. This will enable the doors to be opened when the ladder is in
front of the doors.
• Do not mount rail brackets directly onto a drywall surface. Always mount these brackets
to solid wood, predrilling the holes in the wood is advisable to avoid splitting the wood.
1. Once the height of where the center of the rail is to be installed is established, mark the
location on the wood surface where the bottom of the mounting bracket will be located.
(The distance between the center of the rail and the bottom of the bracket is different for
different brackets. See the bracket dimensional specs below for proper measurements).
Verify with a quality leveling device that the horizontal locations of the brackets are level
and true.
Quiet Glide Double-Hook style Hardware Installation Instructions
Revision date: 7/24/2019
Horizontal Hook
Horizontal Roller
Vertical Hook
Vertical Roller
3
2. To splice rails together using the Quiet Glide splice kit (QG.41) complete the following steps.
• Insert the roll pin halfway the length of the pin into one of the rails (Figure 1)
• Slide the steel bar halfway into the rail and tighten 2 of the set screws to lock the bar and
roll pin onto the rail (Figure 2)
• Line up the roll pin hole and slot for the steel bar on the other rail and slide the rail over
the pin and bar till a tight connection is made between rails (Figures 3 & 4)
• Complete the splice by tightening the remaining 2 set screws
3. Slide all the brackets onto the rail, recommended spacing of the brackets is
approximately 32” apart.
4. Using the level horizontal line as a guide, secure each bracket to the wood surface
with the included screws.
Figure 4
Figure 2
Figure 3
Figure 1
4
5. Installing the end caps to the rail (see Figures 5-8)
• Using a ¼”-20 tapping tool, tap the ends of the rail.
• Secure the end cap to the rail using the supplied ¼”-20 KD bolt and a 4mm Allen wrench.
Figure 8
Figure 6
Figure 7
Figure 5
5
Step 2: Ladder Assembly
Special application notes:
To determine the length of the ladder required for one’s specific application:
Measure from the center of the installed rail to the floor, then add 5” to the measurement.
(It is recommended that the ladder rail sides and steps are sanded slightly with a 220
grit sand paper just prior to applying the finish (stain, paint, clear coat sealer) on the
ladder.
It is also much easier to apply the finish to the ladder prior to assembly, taking care
to protect the inside of the dados of the side rails and the ends of the steps from the
applied finish that would prevent a good strong glue bond between the steps and the
side rails)
1. Stand on edge one of the ladder side rails on a flat surface, dados facing away from
you.
2. Insert one of the steps into the dado, aligning the compound miter of the step flush
with the dadoed surface of the side rail. If not flush, flip and/or rotate the step until it
lines up properly with the side rail.
3. Once proper alignment of the step is established, apply a thin film of quality
woodworker’s glue to the end of the step and also in the dado.
4. Using the supplied 1-3/4” washer-head screws, secure the step to the side rail
through the predrilled holes on the side rails. Assemble the remaining steps in the same
manner.
(Don’t forget to glue in the top turned rung!)
5. Once all the steps are assembled onto one of the side rails, position the side rail on its
side with the steps pointing up.
6. Apply a thin film of glue on the ends of each step and in the dado of the other rail,
along with the holes in the sides of the rail (for the top turned rung) and the ends of the
top turned rung.
7. Properly align each step as well as the top turned rail into its corresponding dado/
hole, use the supplied 1-3/4” washer-head screws to fasten the steps into place.
8. To install the step support rods, push a nut cap (used with the step support rods) in
the predrilled hole on the side rail. Slide the step support rod through the hole on the
opposite side rail and partially thread it into the nut cap. Install the other nut cap and
using two 5mm Allen wrenches tighten each side simultaneously so that there is equal
amounts of thread on each end of the rod into each nut cap.
6
Step 3: Double-Hook Hardware Installation
Bottom Ladder Hardware (non-skid foot, non-rolling)
1. After the ladder is finished and assembled, take the non-skid foot and center it on the
bottom of the ladder side rail (Figure 1)
2. Mark the location of the non-skid foot and measure the distance from the front edge of
the ladder to the mark (Figure 2) 3. On the other ladder side rail measure use the same
measurement obtained on the other ladder side rail to locate the non-skid foot.
(The location of the non-skid feet on each of the ladder side rails should be the same)
4. Using a 5/16” drill bit, drill the holes for the ¼-20 KD bolt fasteners that will fasten the
non-skid foot to the bottom of the ladder.
(Be careful to drill the holes straight in the ladder side rail so that the bolt will line up with
the holes on both sides of the non-skid foot)
5. Use a 7/16” socket and a 4mm Allen wrench to fasten the KD bolts and acorn nuts
through the non-skid foot onto the ladder side rails (Figure 3)
Top Ladder Hardware (Double-Hook, non-adjustable upper guide)
1. After the non-skid feet are installed take the ladder and stand it up parallel to the wall in
its stored position, leaning on the mounting rail (Figure 4)
Figure 2
Figure 3
Figure 1
7
2. Take one of the Double-Hook upper guides and loosely attach it to the angled portion
of the ladder side rail above the mounting rail, hooks pointing down
Pull the ladder slightly away from the mounting rail and slide the Double-Hook upper
guide down so that the lower hook engages firmly onto the mounting rail, this will be
the location of this upper guide on the ladder (Figure 5)
3. Outline the location of this upper guide on ladder side rail (figure 6)
Figure 4
8
4. Remove the upper guide from the ladder, lay the ladder down, measure from the tip of
the ladder to the outlined mark where top of the upper guide is located and transfer this
same measurement onto the other ladder side rail (the location of the upper guide on each
of the ladder side rails should be the same)
5. Using a 5/16” drill bit, drill the holes for the ¼-20 KD bolt fasteners that will fasten the
Double-Hook upper guide to the top of the ladder.
Be careful to drill the holes straight in the ladder side rail so that the bolt will line up with
the holes on both sides of the upper guides (figure 7)
6. Install the ladder on the mounting rail using the bottom hook of the upper guide. The
ladder should now stand upright parallel to the wall, this is the stored position (figure 8).
Figure 6
Figure 7
Figure 5
9
7. Remove the ladder from the rail and reinstall it on the upper hook. The ladder should
now be in the climbing position, approximately at a 12-degree angle (figure 9)
Figure 9Figure 8

Popular Rack & Stand manuals by other brands

SKY-WATCHER AZGTi manual

SKY-WATCHER

SKY-WATCHER AZGTi manual

Celestron Adjust-4270M instruction manual

Celestron

Celestron Adjust-4270M instruction manual

peerless-AV EPT630 manual

peerless-AV

peerless-AV EPT630 manual

CNC Router Parts PRO4848 Assembly instructions

CNC Router Parts

CNC Router Parts PRO4848 Assembly instructions

Vivo STAND-V012T instruction manual

Vivo

Vivo STAND-V012T instruction manual

PRO SIGNAL ST03917 Assembly & user manual

PRO SIGNAL

PRO SIGNAL ST03917 Assembly & user manual

Vertiv DCE E42611 user guide

Vertiv

Vertiv DCE E42611 user guide

Habitat Oto 821030 manual

Habitat

Habitat Oto 821030 manual

CHIEF LCB1UP installation instructions

CHIEF

CHIEF LCB1UP installation instructions

Reflecta 23055 installation manual

Reflecta

Reflecta 23055 installation manual

Keysight Technologies Keysight N5470A installation guide

Keysight Technologies

Keysight Technologies Keysight N5470A installation guide

PEERLESS Paramount PRT2X2 installation guide

PEERLESS

PEERLESS Paramount PRT2X2 installation guide

PEERLESS Mounts LCT-A1B1C Installation and assembly

PEERLESS Mounts

PEERLESS Mounts LCT-A1B1C Installation and assembly

Atlas Clamping Rack Shelves SH Series Specifications

Atlas

Atlas Clamping Rack Shelves SH Series Specifications

Accessory Power ENHANCE ENPCGXH100BKEW user guide

Accessory Power

Accessory Power ENHANCE ENPCGXH100BKEW user guide

Graco 24Y479 instructions

Graco

Graco 24Y479 instructions

Advantech PPC-L157 Series Setup guide

Advantech

Advantech PPC-L157 Series Setup guide

Sabaj In-Stand Assembly and operating manual

Sabaj

Sabaj In-Stand Assembly and operating manual

manuals.online logo
manuals.online logoBrands
  • About & Mission
  • Contact us
  • Privacy Policy
  • Terms and Conditions

Copyright 2025 Manuals.Online. All Rights Reserved.