Ctl CTL 5xn User manual

COLOR MONITOR
Model No : CTL 5xn
USER
'
SMANUAL

1. Read all of these instructions.
2. Save these instructions for later use.
3. Unplug this monitor from the wall
outlet before cleaning. Do not use liquid
cleaners or aerosol cleaners. Use a damp
cloth for cleaning.
4. Do not use attachments not recommended by the
monitor manufacturer as they may cause hazards.
5. Do not use this monitor near water for example, near
a bathtub, washbowl, kitchen sink, or laundry tub, in a
wet basement or near a swimming pool, etc.
6. Do not place this monitor on an
unstable cart, stand, or table. The monitor
may fall, causing serious injury to a child
or adult, and serious damage to the
appliance.
7. Slots and openings in the cabinet and
the back or bottom are provided for
ventilation, and to ensure reliable
operation of the monitor and to protect it
from overheating, these openings must not be blocked
or covered. The openings should never be blocked by
placing the monitor on a bed, sofa, rug, or other similar
surface. This should never be placed near or over a
radiator or heat register. This monitor should not be
placed in a built-in installation such as a bookcase
unless proper ventilation is provided.
8. This monitor should be operated only
from the type of power source indicated
on the marking label. If you are not sure
of the power supplied to your home,
consult your monitor dealer or local
power company.
9. This monitor is equipped with a 3-wire
grounding type plug, a plug having a
third (grounding) pin. This plug will only
fit into a groundingtype power outlet.
This is a safety feature. If you are unable
to insert the plug into the outlet, contact your electrician
to replace your obsolete outlet. Do not defeat the
purpose of the groundingtype plug.
10. Do not allow anything to rest on the
power cord. Do not locate this monitor
where the cord will be abused by persons
walking on it.
11. Follow all warnings and instructions marked on the
monitor.
12. For added protection for this monitor
during a lightning storm, or when it is left
unattended and unused for long periods of
time, unplug it from the wall outlet. This
will prevent damage to the set due to
lightning and powerline surges.
13. Do not overload wall outlets and extension cords as
this can result in fire or electric shock.
14. Never push objects of any kind into this monitor
through cabinet slots, as they may touch dangerous
voltage points or short out parts that could result in a
fire or electric shock. Never spill liquid of any kind on
the monitor.
15. Do not attempt to service this monitor
yourself as opening or removing covers
may expose you to dangerous voltage or
other hazards. Refer all servicing to
qualified service personnel.
16. Unplug this monitor from the wall outlet and refer
servicing to qualified service personnel under the
following conditions:
a. When the power cord or plug is damaged or frayed.
b. If liquid has been spilled into the monitor.
c. If the monitor has been exposed to rain or water.
d.If the monitor does not operate normally by following
the operating instructions. Adjust only those controls
that are covered by the operating instructions as
improper adjustment of other controls may result in
damage and will often require extensive work by a
qualified technician to restore normal operation.
e.If the monitor has been dropped or the cabinet has
been damaged.
f. When the monitor exhibits a distinct change in
performance this indicates a need for service.
17. When replacement parts are
required, be sure the service technician
has used replacement parts specified by
the manufacturer that have the same
characteristics as the original part.
Unauthorized substitutions may result
in fire, electric shock, or other hazards.
18. Upon completion of any service or repairs to this
monitor, ask the service technician to perform routine
safety checks to determine that the monitor is in safe
operating condition.
IMPORTANT SAFEGUARDS

FEDERAL COMMUNICATIONS COMMISSION RADIO
FREQUENCY INTERFERENCE STATEMENT
NOTE: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the
following measures :
ƒ¡Reorient or relocate the receiving antenna.
ƒ¡Increase the separation between the equipment and receiver.
ƒ¡Connect the equipment to an outlet on a circuit different from that to
which the receiver is connected.
ƒ¡Consult the dealer or an experienced radio, TV technician for help.
CANADIAN DEPARTMENT OF COMMUNICATIONS
COMPLIANCE STATEMENT
This digital apparatus does not exceed the Class A/Class B (whichever
is applicable) limits for radio noise emissions from digital apparatus set
out in the Radio Interference Regulations of the Canadian Department of
Communications.
Avis de conformité aux normes du Ministère des Communications du
Canada.
Le present appareil numérique n¡flemet pas de bruits radioélectriques
depassant les limites applicables aux appareils numériques de Class
A/de Class B (selon le cas) prescrites dans le règlement sur le brouillage
radioélectrique édicte par le ministère des communications du canada.
CAUTION: Any changes or modifications not expressly approved by the
part responsible for compliance could void the user's authority
to operate the equipment.

The power cord is used as a main disconnect device. Disconnect the power
cord before servicing.
The outlet must be installed near the monitor and must be easily accessible.
As an E NERGY S TAR Partner, Daewoo Electronics Co., Ltd. has determined that
this product meets the Energy Star guidelines for energy efficiency.

Introduction 1
Product Features 2
Setup 3
Installing the Tilt/Swivel Stand 3
Connecting the D-Sub Signal Cable 4
Connecting to Your Macintosh Computer 4
Connecting the Power Cord 4
Power Management System 5
DDC for Plug & Play 5
Operation & Adjustment 6
Specifications 9
Factory Preset Timings 10
Troubleshooting 11
Appendix
Description for D-sub Connector
CONTENTS

This manual explains how to correctly install, operate and get the
best performance from your monitor. Please read this user's
manual carefully before installing your monitor, then keep it near
your monitor for quick reference.
First, please check that the contents of the carton box corresponds
with the following checklist :
¡Color monitor
¡Power cord
¡Tilt/swivel stand
¡User's manual
¡Warranty Handbook
¡Warranty Registration Card
If there is any item missing or damaged, please contact your
dealer. Please keep the carton box and packing materials so that
you may properly store or transport your monitor.
1
INTRODUCTION
English

PRODUCT FEATURES
¡The convenient and user-friendlly on-screen display allows for
easy and accurate adjustments of horizontal and vertical screen
size and position, geometry and screen color.
¡The monitor supports a safe working environment in strict
compliance with the MPR¥–standard for low emissions.
¡The monitor complies with the VESA Display Data Channel
(DDC) specification for “Plug & Play” compatibility. Advanced
microcircuitry makes set-up and configuration fast and
effortless.
¡The monitor features Advanced Color Controls for fine-tuning
to meet your own personal tastes or application requirements.
Use the on-screen controls to adjust the color temperature, RB
gain value for the best possible screen color and intensity.
¡Just activate the higher refresh rates of the monitor to stabilize
the screen and eliminate the annoying flicker that contributes to
eye-strain and headaches.
¡The “borderless” full-screen display capability works under all
graphic modes and provides a larger viewing area than
conventional monitors, giving you a better picture with more
workspace.
2

INSTALLING THE TILT/SWIVEL STAND
1. Ensure that the power to the monitor is off.
2. Set the monitor face down with the underside facing you.
Please be careful so as not to scratch the monitor screen.
3. Align the four hooks on the stand with the guide holes of
bottom chassis of the monitor.
4. Insert the hooks into the guide holes.
5. Slide the tilt/swivel stand toward the front of the monitor until
the latch locks in position.
6. Turn the monitor and the stand upright.
If you want to remove the tilt/swivel stand on the monitor, press
the latch and pull the tilt/swivel stand toward the back of the
monitor. Lift the stand to separate.
3
SETUP
2
PUSH
1
PUSH
FRONT
<Removing the tilt/swivel stand>
English

CONNECTING THE D-SUB SIGNAL CABLE
1. Turn off the computer and monitor.
2. Connect the 15 pin D-sub connector to the output port of the
video card in your computer.
3. Tighten the screws of connector.
CONNECTING TO YOUR MACINTOSH COMPUTER
1. Turn off the computer and monitor.
2. Attach the Macintosh cable adapter to the Macintosh video
card.
3. Tighten the screws on the cable adapter.
4. Connect the signal cable provided with your monitor to the
other end of the Macintosh cable adapter.
5. Tighten the screws between the Macintosh cable adapter and
the signal cable.
CONNECTING THE POWER CORD
1. Plug the power cord into the AC receptacle located at the back
of the monitor.
2. Plug the other end of the power cord into the AC outlet.
4
If your power cord is PC to Monitor type, plug the other end of the
power cord into the AC receptacle in the computer.

POWER MANAGEMENT SYSTEM
If you use the monitor with a computer which complies with the
power saving program, you can set the monitor to go blank when
the system has remained unused for a period of time. To specify
the period or to disable this feature, set the system timeout field
of the computer's system setup program or use special software
for power saving. See the computer user's manual for the details
of using the system setup. While the monitor is in power saving
mode (blank screen), it consumes less power than normal
state;the color of the power LED will indicate the state. To restore
the screen image, press any key of your keyboard or move your
mouse. If the signal cable is connected loosely or disconnected,
the power saving feature will operate.
DISPLAY DATA CHANNEL (DDC) FOR PLUG & PLAY
If you use the monitor with a computer which complies with
DDC1/2B of VESA, the Host-Video Card automatically
configures itself without your intervention in a way that best fits
the attached monitor.
The Display Data Channel, DDC, allows the monitor to inform
the host system about configuration information for optimum
use of the monitor . Use of the Video Card utility is not required
to match the resolutions and refresh rates of the monitor and
video card.
5
English