CTS OE0052 User manual
www.centretank.com
PRODUCT MANUAL
PRODUCT CODES
OIL TALLY HEATING OIL METER
OE0052
›Flow range: 1 to 50 litres per hour (maximum 60 lph intermittently)
›Accuracy: +/-0.5% of reading (repeatability +/-0.1%)
›Maximum working pressure: 25 bar (pressure loss 0.2 bar max)
›Temperature range: -30°C to 80°C
›Installation and service of this equipment must only be carried out by competent persons
›The installation must conform to all relevant regulations and standards
›the sealing plugs in the meter inlet and outlet threads must be removed before installation
›For internal installations only
›Observe the ow range - the meter will not operate with ows outside the range given
›Not suitable for external tting
Your Oil Tally meter has a mechanical register with the following features:
›A seven digit non-resettable display showing the accumulated total in litres to 99999.99
The black digits are complete litres and the 2 last red digits represent 0.10 litre giving a reading to
two decimal places 0.00 ). For example; 0074460 would read as 744.6 litres.
›A red sweep hand on a dial showing 0.01 of a litre. When read in conjunction with the main display
this gives a reading to two decimal places (0.00).
›A black spinning visual indicator shows that ow is present through the meter.
www.centretank.com
Important Safety Notes
How To Read Your Meter
Product Information
PRODUCT INFORMATION
OIL TALLY HEATING OIL METER
www.centretank.com
OIL TALLY HEATING OIL METER
›Always install the meter based on the direction of ow as shown by the arrow on the meter.
›The meter can be installed on the suction or delivery side of the boiler pump.
›The meter can be installed horizontally or vertically, but if vertically, the ow must be upwards through
the meter. Please note: Incorrect installation can cause premature wear of meter components.
›The pipe layout must ensure that the meter is lled with uid at all times.
›Where back-ow may occur a non-return valve should be tted after the meter to prevent inaccurate
readings.
›An 80 micron lter should be tted before the meter to prevent impurities entering and damaging the
meter.
›The meter is supplied with two 10mm compression x 1/4” BSPM adapters. After removing the
sealing plugs, the 1/4” BSPM ends should be tightened into the inlet and outlet threads of the meter
(max 7Nm). Then add the nuts and olives. The tted washers will seal the adaptors to the meter and
no sealant or thread tape is required.
›The 10mm compression ttings are used to connect the meter into a 10mm oil line. After turning
off the oil ow a section pipe should be removed to allow the installation of the meter into the line.
For lines other than 10mm additional adaptors (not supplied) will be required and the removed pipe
length may vary.
›To prevent stress on the pipe and connections support the meter if necessary.
›Turn on the oil ow and check the meter for correct operation and all uid connections for leaks.
Installation Instructions
INSTALL ATION
›The meter does not register any ow and no oil is reaching the appliance -
Check that the oil tank is not empty; Check that the lter is not clogged and preventing oil from
passing; Check that there is oil in the system and not air by undoing the tting at the appliance and
allowing air to escape until oil ows freely; check that the system ow rate is greater than 1 litre per
hour; check that no foreign bodies have clogged the inlet to the meter; check that any non-return
valve tted is working.
›The meter does not register any ow but oil is reaching the appliance -
Check that the system ow rate is greater than 0.5 but no more than 60 litres per hour.
www.centretank.com
OIL TALLY HEATING OIL METER
›Warranty for this meter is subject to a standard 12 month warranty from the date of dispatch. For
service advice please call us on 0121 351 4445 or email sales@centretank.com.
Problem Solving
Warranty
TROUBLESHOOTING
Table of contents
