Customer service: 0871 855 6100
For more innovative products from Easylife please visit:
www.easylifegroup.com
Paper weight 60gsm
PANTONE 072 C
PANTONE 123 C
PRODUCT INFORMATION
This soup maker is designed to make either smooth or chunky soups. It also features a reheat function
allowing precooked soups to be reheated, ready to serve. The built in blades can also be used solely
as a blender to make smoothies, purees, dips and dressings. It also features a steaming program to
steam cook small quantities of food.
The soup maker is tted with several safety features including an interlocking lid with a safety cut-out;
a minimum liquid sensor; a hot liquid overow sensor and a safety micro-switch cut-off on the motor
base.
INSTRUCTIONS FOR USE
Before using the soup maker for the rst time, rinse out the jug and wipe the lid with a damp cloth. The
use of a mild detergent is recommended.
Warning: The jug contains very sharp blades and should be handled with care at all times.
Do not immerse the unit or jug in water or any other liquids.
Place the base unit on a heat-resistant, stable surface. Carefully position the jug on the base unit
aligning the connections in the base of the jug handle with those in the base unit. The jug should sit
securely on top of the base unit.
Cut all your ingredients into approximately 2-3cm pieces. Items chopped larger may not cook in
the programmed time. Also ensure that all ingredients used in programs 1, 2 and 3 are at room
temperature. Frozen ingredients can be used with the pre-set program 4, or with the manual blending
feature only.
Warning: Do not use raw meats in the soup maker. Any meat or sh must be pre-cooked.
Ensure all ingredients are at room temperature.
Please note: The pre-set programs rely on uninterrupted operation. Any interruption will result in the
cancellation of the program. Restarting will result in the cooking stages being repeated which may
affect the nished result.
If you need to add additional ingredients during the cooking process you can remove the lter lid and
insert food without interrupting the program. If you remove the main lid the program will stop and you
will need to start it again.
How to use the pre-set programs
PROGRAM 1 – THIS MAKES SMOOTH SOUP
Method:
Place the soup maker jug on the base ensuring that it is positioned correctly. You DO NOT need the
stainless steel lter for this program. Place all the ingredients into the jug. Add the stock / water the
MAX SOUP level.
• Place the lid on the jug, ensuring that it is properly locked in place.
• Connect the soup maker to the mains power supply and switch on. The soup maker will BEEP
when the mains power is switched on and each time you press any of the buttons.
• Press the START / STOP button once.
• Press the MENU button once – the display will change and will read OFF. Press the MENU button
again. The soup maker display will now show P1.
• Press the START / STOP button once more to start the selected program.
The soup maker starts by heating up the ingredients in the jug. Only once the correct temperature has
been reached will the blender blades activate for a short burst to chop and mix the ingredients. This
can take up to 10 minutes, dependent on the temperature of the ingredients used. The soup maker will
repeat the heat / blending cycle twice more during the program. At the end of the nal cycle the soup
maker will blend all the contents for 4 longer bursts to ensure that all the ingredients are liquidised fully
before switching off. The soup maker will sound 4 long BEEPS to indicate the end of the program. This
program should take no more than 20 minutes.
Your soup is now ready to serve, remove the jug carefully from the base unit, taking care not to touch
the sides of the jug which will be hot. Remove the lid and serve.
PROGRAM 2 – THIS MAKES CHUNKY SOUP
Method:
Place the soup maker jug on the base ensuring that it is positioned correctly. Place the stainless steel
lter inside the jug so the blades remain inside the lter. Place al the ingredients into the jug. Please
note that the ingredients placed inside the lter will be liquidised, any ingredients placed outside the
lter will remain whole. Add the stock / water the MAX SOUP level.
• Place the lid on the jug, ensuring that it is properly locked in place.
• Connect the soup maker to the mains power supply and switch on. The soup maker will BEEP
when the mains power is switched on and each time you press any of the buttons.
• Press the START / STOP button once.
• Press the MENU button once – the display will change and will read OFF. Press the MENU button
twice more. The soup maker display will now show P2.
• Press the START / STOP button once more to start the selected program.
The soup maker starts by heating up the ingredients in the jug. Only once the correct temperature
has been reached will the blender blades will activate for a short burst to chop and mix the ingredients
within the lter. This can take up to 10 minutes, dependent on the temperature of the ingredients
used. The soup maker will repeat the heat / blending cycle twice more during the program. At the
end of the nal cycle the soup maker will blend all the contents for 4 longer bursts to ensure that all
the ingredients are liquidised fully before switching off. The soup maker will sound 4 long BEEPS to
indicate the end of the program. This program should take no more than 25 minutes.
Your soup is now ready to serve, remove the jug carefully from the base unit, taking care not to touch
the sides of the jug which will be hot. Remove the lid and stainless steel lter and serve.