Current Cost EnviR User manual

Monitor User Guide

2 3
Introduction
Thank you for making the decision to reduce your energy usage (and your energy bills). It’s not all
about cutting use, homes need energy to function, but identifying waste and cutting it, is one way of
helping the planet by reducing our emissions of greenhouse gases.
Current Cost is the leading global provider of real time in-home energy monitors. As an innovative
manufacturer we have successfully distributed over 1,800,000 products throughout the globe.
The Current Cost ethos is to empower consumers with real time information that helps them identify
energy usage and its cost, enabling them to change energy awareness and habits. We don’t want you
to stop using... just wasting!
The beauty of the Current Cost energy monitor is that it shows how much energy you’re using right
now. The EnviR also illustrates how much it is going to cost you everyday and every month. It’s easy;
by making small changes you could receive some big savings.
Keep your EnviR monitor somewhere easy to observe and you’ll soon realise how simple it is to save
money, turn your appliances off standby or switch the light off when you leave the room and see how
much this changes the reading. Check the display before you leave the house or go to bed... it’s
amazing how much energy you waste without realising.

4 5
Table of contents
Introduction 3
Before you get started 5
Sensor Type 6
1. CT Jaw 6
How it works 6
Have you got everything? 6
2. OptiSmart Reader 6
How it works 6
Have you got everything? 6
Setting up your EnviR – CT Jaw Monitor 7
Pairing the EnviR display and transmitter 7
‘Sensable’ Software – Voltage adjustment 8
‘Sensable’ Software – Pairing additional C² enabled displays to the transmitter 8
Fitting the transmitter to your meter 9
Understanding the EnviR display 10
Setting up your EnviR – OptiSmart Reader Monitor 11
Setting up your EnviR display 11
Pairing the EnviR display and transmitter – electronic meter ‘appliance 9’ screen 11
Display/Sensor pairing 2 – Main screen (Energy Now Data) 11
At the property’s electricity meter 12
Setting the clock 13
Adjusting your electricity price 13
Setting an additional rate 13
IAMs – Individual Appliance Monitor 14
PC connectivity 14
NetSmart 14
Fascias 14
C² & S² Technology 14
Troubleshooting 15
Technical Information 16
Contact Us 16
Before you get started – Safety and care of your EnviR monitor
It’s important you observe some simple precautions before using the product.
The EnviR monitor does not require you to carry out any electrical wiring. However, the transmitter has
to be installed at the meter near the electrical supply to your property.
If you have any doubt about how to install it safely do not attempt to install it yourself, but
consult a qualied electrician.
Similarly, if you notice anything unusual about your electricity supply, such as loose wires, exposed
cabling, burn marks or holes in the insulating materials or damage to your meter then STOP
immediately and consult a qualied electrician.
Do not attempt to repair or service any part of the EnviR monitor.
Contact our customer service department for assistance.
Do not immerse the product in water, or any other liquids.
Do not expose the product to heat, ame, steamy conditions or extreme cold.
Do not open the equipment or touch any of its electronic circuitry.
Do not hit, strike or drop the equipment. If the display gets broken take special
care not to touch the liquid crystals.
Do not use this product for any purpose other than for which it was intended.

6 7
Setting up your EnviR – CT Jaw Monitor
Setting up your EnviR display
1) The display power adapter should be connected to the round socket found in the
base of the display unit.
2) Plug the display power adapter into a convenient wall socket.
3) The ‘Energy Now’ value on the display will now show dashes. The EnviR energy monitor
should be left powered on at all times to read energy correctly and run its clock.
4) Remove the plastic battery tab from the back of the black transmitter unit; the transmitter
will now be activated.
5) If the display shows ‘0 Watts’ the display has already been paired and is ready to use. If it
shows dashes the display and transmitter need pairing. It is good practice to uniquely pair
your display to avoid cross communication with a neighbours monitor.
Pairing the EnviR display and transmitter
1) Place the transmitter and the display in the same room.
2) On the front locate the recessed tuning button in the centre of the transmitter.
3) Using a used match, pen or similar, push and hold the recessed tuning button or until the
LED on the transmitter has ashed ONCE only.
4) Upon releasing, the red LED on the transmitter will rapidly ash for a minute. If it doesn’t,
please try again.
5) Whilst the LED on the transmitter is ashing, press and hold the DOWN button on the
display until the LED on the display ashes.
6) When you release the button, the screen will show a tuning signal indicating the display is
tuning to the transmitter. When your monitor and transmitter are tuned, the middle right of the display
will show ‘240’ (indicating UK domestic voltage).
7) Once the process is completed, your display will clear and then ‘0 watts’ will appear. This
usually takes 1 to 2 minutes. The aerial icon will appear indicating pairing has been successful.
Meter
MAINS SUPPLY TO HOUSE VIA FUSE BOX
/SWITCHBOARD
00035252
Button
1
OPTION
Sensor Type
The Current Cost EnviR now comes with a choice of 2 sensor types:
1 CT Jaw
Adapter
For installation instructions please
refer to pages 7 - 10 and then 13 - 16
How it works:
The EnviR monitor shows real time information;
a wireless signal is sent every six seconds from
a transmitter attached via a CT jaw to your
meter and then to the display. This enables
you to view your energy consumption easily,
showing changes in power consumption when
different electrical appliances are used.
Contents of your box
• EnviR Display
• S² transmitter with CT Jaw
• Power Adapter for Display
• Instruction manual
• 1 year Warranty (option to extend online)
How it works
The EnviR monitor shows real time information;
a wireless signal is sent every six seconds from
a transmitter attached via an optical reader
to your meter and then to the display. This
enables you to view your energy consumption
with 100% accuracy, easily showing changes in
power consumption when different appliances
are used.
Contents of your box
• EnviR Display
• C² White OptiSmart transmitter
• OptiSmart Reader
• Power Adapter for Display
• Instruction manual
• 1 year Warranty (option to extend online)
For installation instructions please
refer to pages 11 - 16
OptiSmart Reader
2
Adapter

8 9
‘Sensable’ Software – Voltage adjustment
The new ‘Sensable’ software found in the EnviR transmitter allows you to set your known voltage.
The default value shown on the display of 240 is correct for almost all homes in the UK and you do not
normally need to change it. If you do wish to change it, for example you have a 220V private electricity
supply, undertake the following steps:
1) Follow the steps 1 through to 6 for ‘Pairing the EnviR display and transmitter.’
2) When you release the button the screen will show a tuning signal indicating the display is tuning to
the transmitter. When your monitor and transmitter are tuning, the middle right of the display will show
‘240’ (indicating UK domestic voltage).
3) At this point if you wish to adjust your voltage setting please undertake the following:
(i) Press and hold the recessed tuning button on the transmitter for 3 seconds and then
release.
(ii) The display will now have changed and will indicate ‘250’.
(iii) Repeat this process to select your known voltage (the range is from 200 to 260V
starting at 240V).
(iv) Each press cycles the voltage shown on the display, so press as many times as you need
to reach the voltage value you want to use – for example if you wished to set 200V you
will need to repeat steps (i) and (ii) three times and the display will show 250, 260 and
then 200.
4) Once completed, your display will clear and then ‘0 watts’ will appear. This usually takes 1 to 2
minutes. The aerial icon will appear indicating pairing has been successful.
*Please note that the voltage shown on the display is used for the EnviRs internal calculations, this has
nothing to do with the display power adapter. The power adapter is designed to work in all UK homes
with no adjustment.
‘Sensable’ Software – Pairing additional C² enabled displays to the transmitter
The new ‘Sensable’ software found in the EnviR transmitter allows you to set up additional C²
enabled displays within the home. To pair additional displays please undertake the following steps:
1) Follow steps 1 and 2 for ‘Pairing the EnviR display and transmitter.’
2) Using a used match, pen or similar, push and hold the recessed tuning button until the LED
on the transmitter has ashed exactly TWICE.
3) Upon releasing, the red LED on the transmitter will rapidly ash for a minute (if it doesn’t, please
try again) indicating that the transmitter is now ready to pair with any additional C² enabled displays,
at the same time as remaining paired with the existing EnviR display.
4) Whilst the LED on the transmitter is ashing, at the additional display(s) press and hold the
DOWN button on the display until the LED on the display ashes.
5) When you release the button on the additional display(s) the screen will show a tuning signal
indicating the display(s) is tuning to the transmitter.
6) Once tuning is completed, all displays will clear and then ‘0 watts’ will appear. This usually takes
1 to 2 minutes. The aerial icon will appear indicating pairing has been successful.
Fitting the transmitter to your meter
1) Now that the transmitter and display are paired plug the CT jaw into the middle socket on the
underside of the transmitter. Take the black transmitter with its attached CT jaw to your mains meter.
This is often on an outside wall or in your garage, utility room or porch. If you live in a at, it can often be
found outside your front door in the communal staircase. The EnviR display unit may be left in any room
you wish to see it, for example the hall or kitchen.
TIP: If you have one electricity meter, t the sensor jaw as described below. If you have two electricity
meters, choose the one, which supplies your household electricity, not the one which supplies your night
storage heaters. If you do have a second meter you will need a second CT jaw to monitor this one.
2) Find the thick round wires connected to the electricity meter. The CT jaw should be placed around the
live cable which runs from your meter to your fuse box, this is usually the fourth cable from the left.
IMPORTANT: When looking at the cables leaving the bottom of the meter, they should be fully insulated
and you should not be able to see any of the cable conductor or core. If you do see the live conductor,
do not touch the cable and consult a qualied electrical installer for advice.
3) Choose a place on the cables length where there is some room around and behind it. Encircle the
cable with the jaw of the CT. Please note, it should not be ‘clamped’ onto the cable. It is safe to ease
the cable forwards to make room, provided this is done gently.
4) Place the transmitter in any suitable dry location, as high as possible where it will not fall within the
length of its cable. As soon as this is done, the EnviR display will start to work. No electrical damage
can occur to either the electrical installation or the transmitter by choosing the wrong cable.
x

10 11
Understanding the EnviR display
When your EnviR display is properly installed you should see a screen similar to the image below:
Indicates the number of sensor jaws installed. For most
domestic situations this will be one
The top line of the display shows you how much energy
you’re using right now. Test it out by switching a light on
and off and watch the gures as they change
Aerial icon conrms information is being read from the
transmitter
The second line down shows how much money you’re
spending. It will also change as you switch electrical
goods on and off. The gures change automatically to
show how much it cost you per day and per month – if
you neglect to turn off your appliances
The third line shows you how much you save when you
turn an appliance off, or spend as you turn it on. It also
shows you the equivalent decrease or increase in energy
usage
This graph shows you how much energy you have used
between 7am to 3pm during the previous day, 3pm
to 11pm the previous evening and 11pm to 7am the
previous night
This shows you your accumulative energy in kWh and
scrolls every ten seconds between the last day, the last
seven days and the last 30 days. You can also scroll
through these using the OK button
The time and the temperature are displayed at all times.
Setting up your EnviR – OptiSmart Reader Monitor
Setting up your EnviR display
1) Unpack the product. Plug the display screen into its mains adapter, and plug the mains
adapter into a wall outlet. The display screen will start working and probably show dashes
instead of numbers.
2) Plug the wire from the OptiSmart reader into the white OptiSmart transmitter box. Rotate the aerial on
the white OptiSmart transmitter to the upright position.
3) Remove the plastic battery tab from the back of the white OptiSmart transmitter unit; the transmitter
will now be activated.
4) The Sensor’s red light will start to ash every 6 seconds.
5) For the next step, you will need some information about your electricity meter. On its faceplate look
for a label that says ‘xxxx imp/kWh’ and note the number.
Pairing the EnviR display and transmitter – electronic meter ‘appliance 9’ screen
1) Place the white OptiSmart transmitter and the display screen in the same room.
2) Using a used match, pen or similar, push and hold the small button in the hole on the front until the
LED on the white OptiSmart transmitter has ashed ONCE, then release.
3) The LED will start to ash faster for about a minute.
4) At the display, use the UP or DOWN buttons to reach the ‘appliance 9’ screen. Now press
and hold the DOWN button until the display’s red LED ashes, then release the button. The
display screen 9 will pair to the transmitter. This will show 1000 (default imp/kWh)
5) If the number is different from the imp/kWh on the electricity meter, use a used match, pen or similar
to press and release the small button in the hole on the sensor so that the number changes.
(The options are 100, 500, 600, 800, 1000, 1250, 1600, 3200, 10000).
After about a minute, the transmitters LED will revert to ashing once every 6 seconds. The display’s
appliance 9 screen will now say ‘DATA’. If the transmitter fast ashing stops before you are ready, do the
Electronic Meter pairing again from Step 1.
Display/Sensor pairing 2 – Main screen (Energy Now Data)
1) Place the white OptiSmart transmitter and the display screen in the same room.
2) Using a used match, pen or similar, push and hold the small button in the hole on the front until the
LED on the white OptiSmart transmitter has ashed three times, then release.
3) The LED will start to ash faster for about a minute.
4) At the display, use the UP or DOWN buttons to reach the main screen (this is the screen
that shows Temperature and Time). Now press and hold the DOWN button until the display’s
red LED ashes, then release the button. The main display screen will pair to the transmitter, clear
and then revert to normal operation.
5) After about a minute, the sensor LED will revert to ashing once every 6 seconds. The displays main
screen will now show ‘0 Watts’. If the transmitter’s fast ashing stops before you are ready; start from
the beginning again.
2
OPTION

12 13
At the property’s electricity meter
1) Take the transmitter and its OptiSmart reader to the property’s electricity meter. On the electricity
meter, locate the ashing red LED labeled ‘kWh’. Ignore any other ashing or steady LED’s. Clean
the area thoroughly around the correct ashing LED using a dry paper tissue.
2) Take the supplied adhesive base and remove the paper backing. Carefully align the hole in the circle
so that the ashing LED shines clearly through the hole, and stick the base to the electricity meter.
When you are happy that it is aligned, apply rm pressure to x the adhesive.
3) Put the transmitter in a convenient place clear of metal surfaces, where its radio antenna can work
effectively.
4) Take the OptiSmart reader, which is plugged into the transmitter, and carefully place it over the base.
When the alignment is correct, the LED inside the optical reader will ash at the same time as the
one on the electricity meter.
When your EnviR display is properly installed you should see a screen similar to the image below:
The following information applies to both sensor types:
Setting the clock
To set the clock on the EnviR display
1) Press and hold the OK button until the LED ashes. (Approx. three seconds)
2) The screen will clear and the clock hours will ash.
3) Use the UP and DOWN buttons to alter the hours. (24-hour format)
4) Once the correct hour has been selected press the OK button.
5) The minutes will now ash, use the UP and DOWN button to set the correct minutes.
6) Push the OK button, the display will return to normal operation.
Adjusting your electricity price
The EnviR display has been programmed with a default p/kWh unit rate. If you wish to change
the unit rate please follow these steps:
1) Push and hold the UP button on the EnviR display until the LED ashes then release.
2) Push the UP or DOWN button to change from pounds/pence to euros/cents.
3) Press the OK button to conrm.
4) The price will then start ashing (i.e. c/p/kWh). Push the UP or DOWN button to
adjust the pence/cents price of the electricity.
5) Press the OK button to conrm.
6) Repeat this process to adjust the fraction of a pence / cents, i.e. 8.07 p/c
7) Press the OK button to conrm and the EnviR display will resume normal operation.
Setting an additional rate
There are several electricity tariffs available, if you pay different kWh unit rates for electricity
consumed, the EnviR display can be set up as follows.
1) Press and hold the UP and DOWN buttons together until the LED ashes and release.
2) Using the UP and DOWN buttons you can now select your low rate unit cost.
3) Press the OK button to conrm when the correct price has been set – if you don’t change the
cost, you will not see the time section.
4) You will then see the clock ashing. Using the UP and DOWN buttons you can now set
the time that your low rate starts. Press the OK button to conrm when the time has been set.
5) Using the UP and DOWN buttons you can set the time your normal rate starts. Press the
OK button to conrm when the time has been set.
6) Normal operation will now resume.
Indicates the number of sensor jaws installed. For most
domestic situations this will be one
The top line of the display shows you how much energy
you’re using right now. Test it out by switching a light on
and off and watch the gures as they change
Aerial icon conrms information is being read from the
transmitter
The second line down shows how much money you’re
spending. It will also change as you switch electrical
goods on and off. The gures change automatically to
show how much it cost you per day and per month - if
you neglect to turn off your appliances
The third line shows you how much you save when you
turn an appliance off, or spend as you turn it on. It also
shows you the equivalent decrease or increase in energy
usage
This graph shows you how much energy you have
used between 7am to 3pm during the previous day,
3pm to 11pm the previous evening and 11pm to 7am
the previous night
This shows you your accumulative energy in kWh and
scrolls every ten seconds between the last day, the last
seven days and the last 30 days. You can also scroll
through these using the OK button
The time and the temperature are displayed at all times.

14 15
IAMs – Individual Appliance Monitor
In-home, real-time individual appliance monitors are a great addition to the Current Cost EnviR energy
monitor. The IAM plug-in device transmits energy usage data of specic appliances to the display (the amount
of Watts consumed and the associated cost). The EnviR can record up to nine IAMs so you can discover the
cost and usage of your electrical appliances in the home.
PC Connectivity
Using the Current Cost RJ45 to USB Data Cable, you can download data from your EnviR monitor to your
PC.
Current Cost HomeSmart Software ** Exclusive to all EnviR users**
This free software has been developed with the rst time user in mind. Easy to set up and use, the
HomeSmart software allows you to track your energy data day and night, helping to understand usage
patterns and more importantly identify where wastage is occurring. When used with the Current Cost Data
Cable you can download your historical data as often as you wish. It’s easy to get started, simply email us at
[e-mail] and we will send you the link.
NetSmart
The Current Cost NetSmart device, allows you to send real time energy usage data to the Current Cost Web
Dashboard by connecting your monitor to your broadband connection. With this device you no longer have to
have your Current Cost display connected to your PC or laptop to send real time data information.
Current Cost Web Dashboard
The Current Cost Web Dashboard is an online service that receives data from ENVI and EnviR models.
The Dashboard allows users to remotely view and interrogate their energy usage via their PC, laptop or
Smart phone, wherever they might be in the world. As well as having the ability to view the data from up to 9
additional channels, customers can also share energy usage on social media platforms such as Facebook
and Twitter.
**Customers will require a NetSmart device to access their data on the Current Cost Web Dashboard.
Fascias
Accessorise your Current Cost EnviR with a range of changeable fascias. The EnviR can now complement
any room with a range of colours. All accessories for the EnviR are available at www.currentcost.com
C2 or S2 Technology
Wherever you see the C2 or S2 logo, you know it’s a member of a family of products that enables you to
manage your energy consumption.
Look out for the logo on other Current Cost products as well as our partner organisations. When you buy a C2
or S2 product you can feel safe in the knowledge that it is of the highest standard and that it will communicate
with your other C2 or S2 equipment.
Troubleshooting
Your Current Cost monitor should reach you in perfect condition. If you have connected it properly but
can’t get it to work, please check the following before contacting us for assistance.
If the information above has not resolved your problem either contact our Customer Service Team on
[phone]
Alternatively visit www.currentcost.com/faq.html to nd our “Frequently Asked Questions” page or
www.currentcost.com/contact.html to contact a member of the Current Cost team.
Problem Possible Cause Solution
No display Faulty display and/or display
power supply
Contact supplier
Corrupted display (incomplete
data)
Faulty display Contact supplier
Alternating readings Display picking up a signal
from a neighbours’ transmitter
Pair your transmitter and
display again, see page 7
Data does not change The clamp should not be
placed around a multicore
cable, but 1 exposed cable.
Refer to diagram on page 9
Costs reading seems
excessively high or low
Correct tariff has not been set Refer to page 13 – Adjusting
your electricity price
Temperature gauge
excessively high
Display too close to heat
source
Choose a different location
enabled
433MHz
enabled
433MHz
Changes or modications not expressly approved by the party responsible
for Compliance could void the user’s authority to operate the equipment.

Technical Information
Monitor Model: EnviR
Product Size: 140mm x 170mm (base) x 105mm
Receiver: 433MHz SRD band
Sensor Coding Recognition: 10 channels (digital and analogue reception)
Subordinate Services: 24hr Clock / ˚C / PC Connectivity. All relevant CE approvals
Manufactured in China for Current Cost Ltd.
(1) 15.105 statement
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna. • Increase the separation between the equipment and
receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected. • Consult the dealer or an experienced radio/TV technician for help.
15.19 statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
15.21 statement
changes or modications not expressly approved by the party responsible for compliance could void
the user’s authority to operate the equipment.
CE Approvals:
ETSI EN 300 220-2 V2.1.1(2006-04), EN 50371 2002, EN 301489-3 v1.4.1 2002-08, EN
60215:1989+A1:1992+A2:1994,
IEC 60950-1:2001(1st Edition) and/or EN 60950-1:2001+A11:2004
How to contact us
By email: [email protected]
By phone: [phone]
Further information is available at www.currentcost.com
enabled
433MHz
enabled
433MHz