Cyclops Lighting PR-20W User manual

USER MANUAL
PR-20W
Mini portable - Warm White LED profile

Caution!.................................................................................................................3
Introduction...........................................................................................................3
Safety instructions ...............................................................................................4
Overview................................................................................................................3
Installation.............................................................................................................4
Read ‘Safety information’ before installing the xture. ..................................................................4
Fastening the xture to a at surface...............................................................................................4
Mounting the xture on a truss .........................................................................................................5
Securing with a safety cable..............................................................................................................5
Power connection...............................................................................................................................5
Operation...............................................................................................................6
Control Menu Map...............................................................................................................................6
Focus ...................................................................................................................................................6
DMX Protocol........................................................................................................6
Troubleshooting ...................................................................................................7
The xture does not work, no light ...................................................................................................7
Technical specications......................................................................................8
Table of contents

3V1.0
Caution!
Be careful with your operations. With a dangerous voltage you can suffer a dangerous electric
shock when touching the wires!
Avoid looking directly into the light source!
Wear protective glasses and other PPE (personal protective equipment) when working on or near
the xture.
For your own safety, please read this user manual carefully before you initial start-up.
Follow operating safety precautions and pay attention to warning signs methods and equipment
on the user manual.
Indoor use only! To prevent risk of re or shock, do not expose this product to rain or moisture. IP
20 rating.
The ambient temperature must always be between -5° C and +45° C.
Always make sure you are connecting this product to the proper voltage in accordance with the
specications in this manual or on the product’s specication label.Make sure it is grounded when
using it!
Unplug mains lead before opening the housing!
Make sure that the power cord is never crimped or damaged by sharp edges. Check the xture
and the powercord from time to time.
Make sure to replace the fuse with another of the same type and rating.
Warning! This symbol indicates a hot surface. Certain parts of the housing can become hot
during operation. After use, wait for a cool-down period of at least 10 minutes before handling or
transporting the device.
Every person involved with the installation, operation and maintenance of this device has to
- be qualied
- follow the instructions of this manual
- consider this manual to be part of the total product
- keep this manual for the entire service life of the product
- pass this manual on to every further owner or user of the product
- download the latest version of the user manual from the Internet
Introduction
Thank you for having chosen PR-20W. You will see you acquired a powerful and versatile device.
Unpack your item. Before you initial start-up, please make sure that there is no damage caused by trans-
portation. Should there be any, consult your dealer and do not use the device.
Safety instructions
This device has left our premises in absolutely perfect condition. In order to maintain this condition and to
ensure a safe operation, it is absolutely necessary for the user to follow the safety instructions and warn-
ing notes written in this user manual. Always disconnect from the mains, when the device is not in use
or before cleaning it. Keep away children and amateurs from the device! There are no serviceable parts
inside the device. Maintenance and service operations are only to be carried out by authorized dealers.

4V1.0
Overview
Installation
Read ‘Safety information’ before installing the xture.
The xture is designed for indoor use only and must be used in a dry location with adequate ventilation.
Ensure that none of the xture’s ventilation slots are blocked.
Fasten the xture to a secure structure or surface. Do not stand it on a surface or leave it where it can
be moved or fall over. If you install the xture in a location where it may cause injury or damage if it falls,
secure it as directed in this user manual using a securely anchored safety cable that will hold the xture if
the primary fastening method fails.
Fastening the xture to a at surface
The xture can be fastened to a hard, xed, at surface that is oriented at any angle. Ensure that the sur-
face and all fasteners used can support at least 10 times the weight of all xtures and equipment to be
installed on it.
Fasten the xture securely. Do not stand it on a surface or leave it where it can be moved or fall over. If
you install the xture in a location where it may cause injury or damage if it falls, secure it as directed be-
low with a securely anchored safety cable that will hold the xture if the primary fastening method fails.

5V1.0
Mounting the xture on a truss
The xture can be clamped to a truss or similar rigging structure in any orientation. When installing the
xture hanging vertically down, you can use an open-type clamp such as a G-clamp. When installing in
any other orientation, you must use a half-coupler clamp that completely encircles the truss chord.
To clamp the xture to a truss:
1. Check that the rigging structure can support at least 10 times the weight of all xtures and equipment
to be installed on it.
2. Block access under the work area.
3. Fold the legs of the mounting bracket together and bolt a rigging clamp securely to the mounting
bracket. The bolt used must be M10, grade 8.8 steel minimum. It must pass through both mounting
bracket legs and be fastened with a self-locking nut.
4. Working from a stable platform, hang the xture with its clamp on the truss and fasten the clamp se-
curely.
5. Secure the xture with a safety cable as directed below.
Securing with a safety cable
Secure the xture with a safety cable (or other secondary attachment) that is approved for the weight of
the xture so that the safety cable will hold the xture if a primary attachment fails.
Loop the safety cable through the eyebolt in the back of the xture and around a secure anchoring point.
Do not loop the safety cable around the xture’s mounting bracket only, as this will leave the xture un-
secured if it separates from the bracket.
Power connection
Power Requirements
The PR-20W zoom luminaire operates on 100 to 240 volts AC (+/- 10%, auto-ranging). The luminaire
contains an auto-ranging power supply.
Connection with the mains:
Connect the device to the mains with the enclosed power supply cable.
The occupation of the connection cables as below:
Cable color Connection International
Brown Live L
Blue Neutral N
Yellow/green Earth(Ground)

6V1.0
Operation
Control Menu Map
MAIN MENU LEVEL 1 FUNCTION INSTRUCTION
A001 001-512 DMX address setting, 3CH mode
d001 001-512 DMX address setting, 1CH mode
Slave Slave mode
Stat 000-255 Dimmer
St01 1-50 Strobe, with speed increasing
Soud Sound mode
Focus
This function allows you to adjust the focus of the xture.
Step 1: Loosen the focus knob on the top of the device.
Step 2: Adjust the focus by sliding the back lenshousing forward or backward.
Step 3: Tighten the focus knob.
DMX Protocol
A.xxx(3 CH Mode) Function Function Control
CH1 Dimmer 000-255: 0-100% dimmer
CH2 Strobe 000-005: No function
006-255: Strobe with speed increasing
CH3 Dimmer delay & sound
000-025: Dimmer delay on
026-200: Dimmer delay off
251-255: Sound mode
d.xxx(1 CH Mode) Function Function Control
CH1 Dimmer 000-255: 0-100% dimmer

7V1.0
Fixture Cleaning
Due to fog residue, smoke, and dust cleaning the internal and external optical lenses and mirror should
be carried out periodically to optimize light output. Cleaning frequency depends on the environment in
which the xture operates (I.e. smoke, fog residue, dust, dew). In heavy club use we recommend clean-
ing on a monthly basis. Periodic cleaning will ensure longevity, and crisp output.
To clean the xture:
1. Disconnect the xture from power and allow it to cool for at least 10 minutes.
2. Vacuum or gently blow away dust and loose particles from the outside of the xture with low-pressure
compressed air.
3. Clean the surfaces by wiping gently with a soft, clean lint-free cloth moistened with a weak detergent
solution. Do not rub glass surfaces hard: lift particles off with a soft repeated press. Dry with a soft,
clean, lint-free cloth or low-pressure compressed air. Remove stuck particles with an unscented tis-
sue or cotton swab moistened with glass cleaner or distilled water.
4. Check that the xture is dry before reapplying power.
Troubleshooting
Listed below are a few common problems that you may encounter, with solutions.
The xture does not work, no light
• Check the connection of power and main fuse. Be sure the external fuse has not blown.
• Measure the mains voltage on the main connector.

8V1.0
www.cyclopslighting.com
Technical specications
Model PR-20W
Light source: 20 watts Warm white LED
Color temperature: 3200 K
LED life expectancy: 50,000 Hrs.
CRI: 90
Fixed lens: 19°, 26°, 36° or 50°
Optional Fresnel lenses
2 Dimmer curves
Strobe
Track adapters
Video icker free
Silent operation
Control protocols: Rotary, DMX
Control channels: 1, 3 CHs
Input voltage: AC100-240V/50-60Hz
Output: 20-42V /600mA DC
DMX connections: 3 pin XLR In/Out male and female
Power connections: 30-42V/600mA adaptor
Dimensions: 295 x 130 x 120mm
Net weight: 1.3 Kg
Color: Black
Housing: Aluminum
IP rating: 20
Operating temperature -5°C/45°C