Cypress FM0+ S6E1C SERIES User manual

FM0-64L-S6E1C3 QUICK START GUIDE
FM0+ S6E1C-SERIES STARTER KIT
• Download and install the FM0+S6E1C-Series
Starter Kit installer FM0PS6E1C3KitSetup.exe
from
www.cypress.com/FM0-64L-S6E1C3
www.cypress.com/FM0-64L-S6E1C3
Kit Contents:
1 FM0+ S6E1C-Series Starter board
2 USB Standard-A to Micro-B cable
3 Quick Start Guide (this document)
1
• Check the jumpers J1 and J2 are open
• Check the jumper J4 has been closed on pin 1
and pin 2
• Connect the board with PC via CN3 using the
USB cable
2
J2 J1
J4

FM0-64L-S6E1C3 QUICK START GUIDE
• Launch the Serial Port Viewer tool from the
start menu
• Click on the Serial Port Viewer icon in
the notication area of the taskbar and
select FM-Link/CMSIS-DAP Cypress FM
Communications Port
• Congure the baud rate as 115200
• Click the Disconnected button to connect
• Press Enter on your PC keyboard to run the
board test demo
3 4
• Key in the option 02 and press Enter to
change the RGB LED color from Red to
Green to Blue. For more information on the
test procedures, refer to the kit user guide
• Use IAR Embedded Workbench or Keil uVision
IDE to develop code examples on this kit
5 6

FM0-64L-S6E1C3 QUICK START GUIDE
1. Arduino interface (CN7-CN10)
2. User button
3. MB9AF312K Programmer and debugger
(CMSIS-DAP)
4. Serial programming mode select (J3)
5. Power supply resource select (J4)
6. USB device connector (CN4)
7. Potentiometer
8. Programming mode jumper of MB9AF312K (J1)
9. Headphone and microphone jack (CN1)
10. Reset button
11. Multicon connector (CN12, CN13)
12. Jumper for current measure (J5)
13. 10-pin JTAG connector
14. Stereo codec
15. Programming mode jumper of FM0+ (J2)
16. Cypress FM0+ MCU S6E1C32D0A
17. RGB LED
18. Cypress 4-Mb NOR Flash
19. 3.3V Voltage Regulator
FM0+ S6E1C-Series Starter Board Details
12
3
4
5
6
7
110 819
11
12
13
14
16
15
17
18
9

© 2016 Cypress Semiconductor Corporation. All rights reserved.
All trademarks or registered trademarks referenced herein are the property of their respective owners.
002-11420 Rev.*A
FM0+ S6E1C-Series Starter Board Details
FM0-64L-S6E1C3 QUICK START GUIDE
FM0+ S6E1C-SERIES STARTER KIT
For the latest information about this kit, visit www.cypress.com/FM0-64L-S6E1C3
Arduino interface
FM0+ S6E1C-Series Starter Kit
NC- Not connected
P0C/D15
P0B/D14
AREF/AREF
GND/GND
P4C/D13
P4E/D12
P4D/D11
P42/D10
P00/D9
P02/D8
P43/D7
P3B/D6
P3C/D5
P35/D4
P3A/D3
P34/D2
P32/D1
P33/D0
NC/NC
5V0/IOREF
RESET/RESET
3V3/3.3V
5V0/5V
GND/GND
GND/GND
5V0/Vin
P22/A0
P23/A1
P15/A2
P11/A3
P12/A4
P13/A5