Cypress FM4-U120-9B560 User manual

Hardware V1.1 / Documentation V1.8
Starter Kit User Guide
FM4-U120-9B560
FM4-U120-9B560-MEM
Document Number: 002-09878 Rev. *B

SHOW TITLE MM/DD/YY 2 SLIDE OWNER
Warranty and Disclaimer
© Cypress Semiconductor Corporation, 2015-2018. This document is the property of Cypress Semiconductor Corporation and its subsidiaries, including
Spansion LLC (“Cypress”). This document, including any software or firmware included or referenced in this document (“Software”), is owned by Cypress
under the intellectual property laws and treaties of the United States and other countries worldwide. Cypress reserves all rights under such laws and treaties
and does not, except as specifically stated in this paragraph, grant any license under its patents, copyrights, trademarks, or other intellectual property rights.
If the Software is not accompanied by a license agreement and you do not otherwise have a written agreement with Cypress governing the use of the
Software, then Cypress hereby grants you a personal, non-exclusive, nontransferable license (without the right to sublicense) (1) under its copyright rights in
the Software (a) for Software provided in source code form, to modify and reproduce the Software solely for use with Cypress hardware products, only
internally within your organization, and (b) to distribute the Software in binary code form externally to end users (either directly or indirectly through resellers
and distributors), solely for use on Cypress hardware product units, and (2) under those claims of Cypress’s patents that are infringed by the Software (as
provided by Cypress, unmodified) to make, use, distribute, and import the Software solely for use with Cypress hardware products. Any other use,
reproduction, modification, translation, or compilation of the Software is prohibited.
TO THE EXTENT PERMITTED BY APPLICABLE LAW, CYPRESS MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO
THIS DOCUMENT OR ANY SOFTWARE OR ACCOMPANYING HARDWARE, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. No computing device can be absolutely secure. Therefore, despite security
measures implemented in Cypress hardware or software products, Cypress does not assume any liability arising out of any security breach, such as
unauthorized access to or use of a Cypress product. In addition, the products described in these materials may contain design defects or errors known as
errata which may cause the product to deviate from published specifications. To the extent permitted by applicable law, Cypress reserves the right to make
changes to this document without further notice. Cypress does not assume any liability arising out of the application or use of any product or circuit described
in this document. Any information provided in this document, including any sample design information or programming code, is provided only for reference
purposes. It is the responsibility of the user of this document to properly design, program, and test the functionality and safety of any application made of this
information and any resulting product. Cypress products are not designed, intended, or authorized for use as critical components in systems designed or
intended for the operation of weapons, weapons systems, nuclear installations, life-support devices or systems, other medical devices or systems (including
resuscitation equipment and surgical implants), pollution control or hazardous substances management, or other uses where the failure of the device or
system could cause personal injury, death, or property damage (“Unintended Uses”). A critical component is any component of a device or system whose
failure to perform can be reasonably expected to cause the failure of the device or system, or to affect its safety or effectiveness. Cypress is not liable, in
whole or in part, and you shall and hereby do release Cypress from any claim, damage, or other liability arising from or related to all Unintended Uses of
Cypress products. You shall indemnify and hold Cypress harmless from and against all claims, costs, damages, and other liabilities, including claims for
personal injury or death, arising from or related to any Unintended Uses of Cypress products.
Cypress, the Cypress logo, Spansion, the Spansion logo, and combinations thereof, WICED, PSoC, CapSense, EZ-USB, F-RAM, and Traveo are
trademarks or registered trademarks of Cypress in the United States and other countries. For a more complete list of Cypress trademarks, visit cypress.com.
Other names and brands may be claimed as property of their respective owners.

SHOW TITLE MM/DD/YY 3 SLIDE OWNER
Information about this PDF Document
▪For your convenience this user guide includes external links that
simplify installing of drivers, software utilities, and quick jumps to
documentation.
▪Some PDF viewer do not allow access to external content by links
because of security reasons.
▪A viewer called “PDF XChange”is provided in the software package
of this starter kit. It’s use is free of charge and no additional
installation is required.
▪Launching “start.bat” opens this user guide in the PDF XChange
viewer.
▪Please ensure you have copied the complete software package
related to this starter kit to use and run the links and examples
given on the next pages.
▪Please contact the Cypress Support for any question.

SHOW TITLE MM/DD/YY 4 SLIDE OWNER
Overview
▪MCU Features, Board Features, and Contents
▪Please check jumper setting / Test it by a GUI
▪The Hardware / Pin Overview
▪The Jumper Table / Jumper Default
▪Board Power
▪Software Examples & Tools
▪Flash Programming
▪JTAG / CMSIS-DAP
▪IAR-Embedded Workbench
▪KEIL µVision
▪Contacts and More
Additional documents
Schematic
Factsheet
Data sheet MB9B560R Series
Peripheral Manual
Peripheral Manual (Timer Part)
Peripheral Manual (Analog Part)
Peripheral Manual (Communication Part)
Flash Programming Manual and Errata
Please visit www.cypress.com to find latest releases of
the above mentioned documents.

SHOW TITLE MM/DD/YY 5 SLIDE OWNER
Features of the Microcontroller
▪The FM4-U120-9B560 and FM4-U120-9B560-MEM
are based on the Cypress Arm®Cortex®-M4 device MB9BF568R
▪The MB9B560R Series includes the following features:
•Up to 1 MByte Flash Memory and 32 KByte Work Flash Memory
•Up to 128 KByte RAM
•Up to 160 MHz clock
•Up to 2 CAN controller 2.0A/B
•Up to 8 UART / LIN / SPI / I²C interfaces
•USB-Host/-Device interface
•SD-Card interface
•Three 12 bit ADCs, up to 24 channels
•Two 12 bit DACs
•Up to 16 channel external interrupts
•Two Multifunction timer with waveform generator, e.g. Motor control
•Timers (ICUs, OCUs, PPGs, others)

SHOW TITLE MM/DD/YY 6 SLIDE OWNER
Features of the Board
▪The FM4-U120-9B560(-MEM) is available in two versions:
Feature
FM4-U120-9B560 FM4-U120-9B560-MEM
External
Power Supply USB, DAP, JTAG or from FM4-U-PERIPHERAL
On
-board Voltage 3.3 V or 5 V 3.3 V
User
-LEDs, Reset-LED 3x User-LEDs (R,G,B) + Reset
Buttons
3x buttons: Reset + External Interrupt + NMI
Potentiometer
AN18 (0V .. Onboard voltage 3.3V/5V)
Debug interface
Onboard CMSIS-DAP incl. Status LEDs (connected, running)
(optional 20 pin JTAG-IF to be used with external JTAG adapter)
Virtual COM port (USB
-2-UART bridge) Yes
USB interface
USB Function (Mini-USB Type B)
SD
-Card interface Yes No
External Memory
No NAND-Flash: 32 MByte
SDRAM: 16 MByte

SHOW TITLE MM/DD/YY 7 SLIDE OWNER
Contents FM4-U120-9B560
▪The FM4-U120-9B560(-MEM) contents
•The FM4-U120-9B560 or FM4-U120-9B560-MEM evaluation board
•One USB mini cable
•1-page flyer
Box FM4-U120-9B560(-MEM) USB cable
Additional information
AB

SHOW TITLE MM/DD/YY 8 SLIDE OWNER
Please Check Jumper Setting
FM4-U120-9B560 supports 5 V and 3.3 V operation
FM4-U120-9B560-MEM supports only 3.3 V operation
Run
LED
3V
NMI
USBF
USBF
USB
Note:
Please set J9 (USB) instead of J7 (CMSIS-DAP)
Please set J19 and J20:1-2 (SIN0/SOT0)
DAP
SIN0
SOT0

SHOW TITLE MM/DD/YY 9 SLIDE OWNER
Test it by Terminal using USB
▪The microcontroller on the FM4-U120-9B560(-MEM)
is already preprogrammed with a test application (<drive:>\sw-examples\testsoftware)
•Install the USB driver first <drive:>\drivers\driverinstaller.exe
•Connect the starter kit to CN4 (USB) with your PC
✓Ensure jumper J9 (USB) is set for correct power supply
✓Ensure jumper J19 and J20:1-2 are set correctly for use of SIN0/SOT0
•Press the ‚Reset‘- Button
•Check the availability for virtual COM port
✓e.g. Windows Device Manager
•Open a serial terminal tool
✓e.g. Cypress Serial Port Viewer
<drive:>\tools\serialportviewer\setup.exe
✓Settings 115200 baud, 8N1
•Press <space> to show welcome menu
•Please select any function
to test the on-board features

SHOW TITLE MM/DD/YY 10 SLIDE OWNER
Test it by a GUI
▪The microcontroller on the FM4-U120-9B560(-MEM)
is already preprogrammed with a test application (<drive:>\sw-examples\testsoftware)
•Install the USB driver first <drive:>\drivers\driverinstaller.exe
•Connect the starter kit to CN4 (USB) with your PC
•Open the PC software
<drive:>\sw-examples\testsoftware\SK-FM4-U120-9B560_demo.exe
•The picture of the board will be shown
with current status of on-board features
•LED allows control of the RGB-LED
✓Just click to the checkboxes
•Status of user-buttons SW2 and SW3
are shown interactively
•ADC represents the potentiometer R11

SHOW TITLE MM/DD/YY 11 SLIDE OWNER
Test it
▪You finished successfully the first test.
▪Next section covers:
•The onboard features
•How to program the Flash
✓Serial ROM Boot loader
USB Direct
UART0
✓On-board CMSIS-DAP
✓JTAG with optional emulator
•How to start with IAR-Embedded-Workbench and KEIL µVision

SHOW TITLE MM/DD/YY 12 SLIDE OWNER
Hardware

SHOW TITLE MM/DD/YY 13 SLIDE OWNER
The Hardware (Top Side) –Jumper
Option: Ext. JTAG
CMSIS-
DAP
Virt. COM
USB-
Device-
Port
R11
VBat -
+
J25 J24
Expansion Header Pin 1-60
Expansion Header Pin 61-120
2
1
60
59
61
62 119
120
RST
INT
NMI
+5V
3V3
J14
J21
3V/5V
J1
J2
J3
J4
J5
J6
J7
J8
J9
J10
J11
J12
J13
J17 J18 J19
J20
Overview

SHOW TITLE MM/DD/YY 14 SLIDE OWNER
Option: Ext. JTAG
CMSIS-
DAP
Virt. COM
USB-
Device-
Port
Variable
Resistor
AN18
VBat -
+
P47 P46
Expansion Header Pin 1-60
Expansion Header Pin 61-120
2
1
60
59
61
62 119
120
RST
INT
NMI
+5V
3V3
Prog/Run
MD1/LED
3V/5V
P22
U5V
JTAG
MD1
MD0
SK
DAP
JTAG
USB
NMI
USBF
USBF
U5V
MD1 MD0
SIN0
SOT0/P22
The Hardware (Top Side) –Jumper
Function Overview

SHOW TITLE MM/DD/YY 15 SLIDE OWNER
The Hardware (Bottom Side)
SD-Card interface
(only FM4-U120-9B560)
NAND FLASH
(FM4-U120-9B560-MEM)
SDRAM
(FM4-U120-9B560-MEM)
Expansion Header Pin 1-60
2
160
59
61
62
119
120
+5V
3V3
J16
Expansion Header Pin 61-120
55.88mm (= 22x 2.54mm)
2.54mm x 30
2.54mm x 29

SHOW TITLE MM/DD/YY 16 SLIDE OWNER
The Hardware –Pin Overview 1 - 20
Pin Microcontroller-Function FM4-U120-9B560 FM4-U120-9B560-MEM
1VCC VCC_MCU 3V3 or 5V0 VCC_MCU 3V3 or 5V0
2 P50/CTS4_0/AIN0_2/RTO10_0/INT00_0/MADATA00_0 SDRAM, NAND FLASH
3 P51/RTS4_0/BIN0_2/RTO11_0/INT01_0/MADATA01_0 SDRAM, NAND FLASH
4 P52/SCK4_0/ZIN0_2/RTO12_0/MADATA02_0 SDRAM, NAND FLASH
5 P53/TIOA1_2/SOT4_0/RTO13_0/MADATA03_0 SDRAM, NAND FLASH
6 P54/TIOB1_2/SIN4_0/RTO14_0/INT02_0/MADATA04_0 SDRAM, NAND FLASH
7 P55/ADTG_1/SIN6_0/RTO15_0/INT07_2/MADATA05_0 SDRAM, NAND FLASH
8 P56/SOT6_0/DTTI1X_0/INT08_2/MADATA06_0 SDRAM, NAND FLASH
9 P57/SCK6_0/MADATA07_0 SDRAM, NAND FLASH
10 P58/SIN4_2/AIN1_0/INT04_2/MADATA08_0 SDRAM
11 P59/RX1_1/SOT4_2/BIN1_0/INT07_1/MADATA09_0 SDRAM
12 P5A/TX1_1/SCK4_2/ZIN1_0/MADATA10_0 SDRAM
13 P5B/CTS4_2/MADATA11_0 SDRAM
14 P30/TIOB0_1/RTS4_2/INT15_2/WKUP1/MADATA12_0 SDRAM
15 P31/TIOB1_1/SIN3_1/INT09_2/MADATA13_0 SDRAM
16 P32/TIOB2_1/SOT3_1/INT10_1/MADATA14_0 SDRAM
17 P33/ADTG_6/TIOB3_1/SCK3_1/INT04_0/MADATA15_0 SDRAM
18 P34/TX0_1/TIOB4_1/FRCK0_0/MNALE_0 NAND FLASH
19 P35/RX0_1/TIOB5_1/IC03_0/INT08_1/MNCLE_0 NAND FLASH
20 P36/SIN5_2/IC02_0/INT09_1/MNWEX_0 NAND FLASH

SHOW TITLE MM/DD/YY 17 SLIDE OWNER
The Hardware –Pin Overview 21 - 40
Pin Microcontroller-Function FM4-U120-9B560 FM4-U120-9B560-MEM
21 P37/SOT5_2/IC01_0/INT05_2/MNREX_0 NAND FLASH
22 P38/SCK5_2/IC00_0/INT06_2 LED_G LED_G
23 P39/ADTG_2/DTTI0X_0/RTCCO_2/SUBOUT_2/MSDCLK_0 SDRAM
24 P3A/TIOA0_1/AIN0_0/RTO00_0/MSDCKE_0 SDRAM
25 P3B/TIOA1_1/BIN0_0/RTO01_0/MRASX_0 SDRAM
26 P3C/TIOA2_1/ZIN0_0/RTO02_0/MCASX_0 SDRAM
27 P3D/TIOA3_1/RTO03_0/MAD00_0 SDRAM
28 P3E/TIOA4_1/RTO04_0/MAD01_0 SDRAM
29 P3F/TIOA5_1/RTO05_0/MAD02_0 SDRAM
30 VSS GND GND
31 VCC VCC_MCU 3V3 or 5V0 VCC_MCU 3V3 or 5V0
32 P40/TIOA0_0/RTO10_1/INT12_1
33 P41/TIOA1_0/RTO11_1/INT13_1
34 P42/TIOA2_0/RTO12_1/MSDWEX_0 SDRAM
35 P43/ADTG_7/TIOA3_0/RTO13_1/MCSX8_0 SDRAM
36 P44/TIOA4_0/RTO14_1/DA0
37 P45/TIOB0_0/RTO15_1/DA1
38 INITX Button Reset / JTAG Button Reset / JTAG
39 P46/X0A Sub-Crystal 32.768 kHz Sub-Crystal 32.768 kHz
40 P47/X1A Sub-Crystal 32.768 kHz Sub-Crystal 32.768 kHz

SHOW TITLE MM/DD/YY 18 SLIDE OWNER
The Hardware –Pin Overview 41 - 60
Pin Microcontroller-Function FM4-U120-9B560 FM4-U120-9B560-MEM
41 P48/VREGCTL
42 P49/VWAKEUP Pull-Down resistor Pull-Down resistor
43 VBAT Battery (CN1) Battery (CN1)
44 C Capacitor 4u7 Capacitor 4u7
45 VSS GND GND
46 VCC VCC_MCU 3V3 or 5V0 VCC_MCU 3V3 or 5V0
47 P4B/TIOB1_0/SCS7_1/MAD03_0 SDRAM
48 P4C/TIOB2_0/SCK7_1/AIN1_2/MAD04_0 SDRAM
49 P4D/TIOB3_0/SOT7_1/BIN1_2/INT13_2/MAD05_0 SDRAM
50
P4E/TIOB4_0/SIN7_1/ZIN1_2/FRCK1_1/INT11_1/WKUP2/MAD06_0
SDRAM
51 P70/TX0_0/TIOA4_2/AIN0_1/IC13_1
52 P71/RX0_0/TIOB4_2/BIN0_1/IC12_1/INT15_1
53 P72/TIOA6_0/SIN2_0/ZIN0_1/IC11_1/INT14_2
54 P73/TIOB6_0/SOT2_0/IC10_1/INT03_2 USB USB
55 P74/SCK2_0/DTTI1X_1
56 PE0/MD1 LED_B / MD1 LED_B / MD1
57 MD0 MD0 MD0
58 PE2/X0 Main-Crystal 4 MHz Main-Crystal 4 MHz
59 PE3/X1 Main-Crystal 4 MHz Main-Crystal 4 MHz
60 VSS GND GND

SHOW TITLE MM/DD/YY 19 SLIDE OWNER
The Hardware –Pin Overview 61 - 80
Pin Microcontroller-Function FM4-U120-9B560 FM4-U120-9B560-MEM
61 VCC VCC_MCU 3V3 or 5V0 VCC_MCU 3V3 or 5V0
62 P10/AN00/RX1_2/SIN1_1/FRCK0_2/INT02_1/MAD07_0 SDRAM
63 P11/AN01/TX1_2/SOT1_1/IC00_2/MAD08_0 SDRAM
64 P12/AN02/SCK1_1/IC01_2/RTCCO_1/SUBOUT_1/MAD09_0 SDRAM
65 P13/AN03/SIN0_1/IC02_2/INT03_1/MAD10_0 SDRAM
66 P14/AN04/SOT0_1/IC03_2/MAD11_0 SDRAM
67 P15/AN05/SCK0_1/MAD12_0
68 P16/AN06/SIN2_2/INT14_1/MAD13_0
69 P17/AN07/SOT2_2/WKUP3/MAD14_0 SDRAM
70 AVCC VCC_MCU VCC_MCU
71 AVSS GND GND
72 AVRL GND GND
73 AVRH VCC_MCU VCC_MCU
74 P18/AN08/SCK2_2/MAD15_0 SDRAM
75 P19/AN09/SIN4_1/IC00_1/INT05_1/MAD16_0
76 P1A/AN10/SOT4_1/IC01_1/MAD17_0
77 P1B/AN11/SCK4_1/IC02_1/MAD18_0
78 P1C/AN12/CTS4_1/IC03_1/MAD19_0
79 P1D/AN13/RTS4_1/DTTI0X_1/MAD20_0
80 P1E/AN14/ADTG_5/FRCK0_1/MAD21_0

SHOW TITLE MM/DD/YY 20 SLIDE OWNER
The Hardware –Pin Overview 81 - 100
Pin Microcontroller-Function FM4-U120-9B560 FM4-U120-9B560-MEM
81 P1F/ADTG_4/TIOB6_2/RTO05_1
82 P27/TIOA6_2/RTO04_1/INT02_2 LED_R LED_R
83 P26/TIOB5_0/SCK2_1/RTO03_1
84 P25/TX1_0/TIOA5_0/SOT2_1/RTO02_1
85 P24/RX1_0/SIN2_1/RTO01_1/INT01_2
86 P23/AN15/TIOA7_1/SCK0_0/RTO00_1/MAD22_0
87 P22/CROUT_0/AN16/TIOB7_1/SOT0_0/ZIN1_1 JTAG JTAG
88 P21/AN17/SIN0_0/BIN1_1/INT06_1/MAD23_0 JTAG JTAG
89 P20/AN18/AIN1_1/INT05_0/MAD24_0 Potentiometer R11 Potentiometer R11
90 VSS GND GND
91 VCC VCC_MCU 3V3 or 5V0 VCC_MCU 3V3 or 5V0
92 P0E/TIOB5_2/SCS6_1/IC13_0/S_CLK_0/MDQM1_0 SD-Card SDRAM
93 P0D/TIOA5_2/SCK6_1/IC12_0/S_CMD_0/MDQM0_0 SD-Card SDRAM
94 P0C/TIOA6_1/SOT6_1/IC11_0/S_DATA1_0/MALE_0 SD-Card
95 P0B/TIOB6_1/SIN6_1/IC10_0/INT00_1/S_DATA0_0/MCSX0_0 SD-Card NAND FLASH
96 P0A/SIN1_0/FRCK1_0/INT12_2/S_DATA3_0/MCSX1_0 SD-Card
97 P09/AN19/TRACED0/TIOA3_2/SOT1_0/S_DATA2_0/MCSX5_0 SD-Card
98 P08/AN20/TRACED1/TIOB3_2/SCK1_0/MCSX4_0
99 P07/AN21/TRACED2/TIOA0_2/SCK7_0/MCLKOUT_0
100 P06/AN22/TRACED3/TIOB0_2/SOT7_0/MCSX3_0