Cypress CY3633 User manual

Cypress Semiconductor
3901 North First Street
San Jose, CA 95134
Tel.: [phone] (toll-free in the U.S.)
[phone]
www.cypress.com
Version 1.1
CY3633
WirelessUSB™ LS Gaming
DVK User’s Guide

Warranty Disclaimer and Limited
Liability
Cypress Corporation makes no warranty for
the use of its products, other than those
expressly contained in the Company’s stan-
dard warranty which is detailed in Cypress’s
Terms and Conditions located on the Com-
pany’s web site. The Company assumes no
responsibility for any errors which may appear
in this document, reserves the right to change
devices or specifications detailed herein at any
time without notice, and does not make any
commitment to update the information con-
tained herein. No licenses to patents or other
intellectual property of Cypress are granted by
the Company in connection with the sale of
Cypress products, expressly or by implication.
Cypress’s products are not authorized for use
as critical components in life support devices
or systems.
WirelessUSB is a trademark of the Cypress
Corporation. PSoC is a trademark of Cypress
Microsystems. All product and company
names mentioned in this document are the
trademarks of their respective holders.
CY3633 User’s Manual,
Version 1.1.
Copyright © 2004
Cypress Semiconductor Corporation.
All rights reserved.

i
Table of Contents
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Quick Start Using the Pre-programmed Chips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
XBOX Quick Start Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
PlayStation2 Quick Start Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Auto-Bind Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Game Controller Calibration Process. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
XBOX Firmware Development . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
XBOX Receiver Dongle Firmware Development . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Software Requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Software Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Compiling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Using the USB Chip Emulator. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Programming. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
XBOX Memory Unit Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Game Controller Firmware Development. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Hardware Configuration For Controller Firmware Development . . . . . . . . . . . . . . . . . . . 13
Compiling and Programming. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
PlayStation2 Firmware Development. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
PS2 Receiver Firmware Development . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
PS2 Game Controller Firmware Development . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

ii

WirelessUSB™ LS Gaming DVK User’s Guide Rev 1.1 Page -1
WirelessUSB™ LS Gaming DVK User’s Guide
1.0 Introduction
The WirelessUSB LS CY3633 Gaming DVK is an add-on to the WirelessUSB LS CY3632 DVK.
The Gaming DVK is intended to serve the gaming industry by providing example wireless solutions
for the XBOX and PlayStation2 (PS2) gaming platforms.
The contents of this DVK combine with the CY3632 DVK to provide a hardware/firmware solution
for XBOX and PS2 gaming platforms. Refer to the CY3632 Users’s Guide for a list of basic hard-
ware components that will be required to use the additional components supplied with the Gaming
DVK. The Gaming DVK provides the following components:
• USB Hub Adapter board with a pre-programmed CY7C65113 USB chip
• XBOX USB Adapter cable (PN 300-11840)
• CY8C27643 PSoC™ pre-programmed adapter board (labeled “XBOX G”) to provide
XBOX Game Controller functionality
• CY8C27643 PSoC™ pre-programmed adapter board (labeled “PS2 G”) to provide PS2
Game Controller functionality
• CY8C27643 PSoC™ pre-programmed adapter board (labeled “PS2 D”) to provide PS2
receiver dongle functionality
•PlayStation interface cable (PN 300-11841)forconnecting the PS2 receiver to the PS2 game
console
• Plastic joystick knobs
• CD-ROM
• Printed documentation
Hardware items that are required from the standard CY3632 WirelessUSB LS DVK, which
are not included in the CY3633 WirelessUSB LS Gaming DVK are:
• Platform Board PDC-9075 (assembly 121-07500*G) with joysticks and potentiometers
installed
• Platform Board PDC-9075 (assembly 121-07501*E) without joysticks or potentiometers
installed
• Two Radio Modules (PDC-9163)
• Standard USB cable (PN 140xc2)

WirelessUSB™ LS Gaming DVK User’s Guide
Page -2 WirelessUSB™ LS Gaming DVK User’s Guide Rev 1.1
The following diagram shows the contents of the CY3633 WirelessUSB LS Gaming DVK.
Figure 1. WirelessUSB LS Gaming DVK Kit Contents
2.0 Quick Start Using the Pre-programmed Chips
Out of the box, the Gaming DVK is ready to support both the XBOX and PlayStation2 gaming plat-
forms.
2.1 XBOX Quick Start Guide
The XBOX system consists of two Platform Boards (PDC-9075): One is used for the XBOX Don-
gle and the other is used for the XBOX Game Controller.
Dongle - Assembly 121-07501*E (the assembly number is printed on a
white sticker near the DC power jack) has the USB Hub
Adapter Board piggy-backed onto socket U2A, and there are
no potentiometers or joysticks loaded on the board.
Game Controller - Assembly 121-07500*G has the PSoC device labeled “XBOX
G” installed into socket U3.
XBOX USB
Adapter Cable
PlayStation2
Interface Cable
Joystick Knobs
CD-ROM
"PS2 G" PSoC Module
"PS2 D" PSoC Module "XBOX G" PSoC Module
Programmed USB Chip
Blank USB
Chips
USB Hub Adapter
Board
PS2 G
PS2 D
XBOX G

WirelessUSB™ LS Gaming DVK User’s Guide Rev 1.1 Page -3
The hardware setup for operating the XBOX gaming system is shown in Figure 2.
Figure 2. XBOX System Hardware Configuration
A close-up of the receiver dongle is shown Figure 3. The XBOX USB Adapter Cable along with a
standard USB cable are used to interface the Platform Board to the XBOX Console. Power for the
receiver is provided by the XBOX USB interface. Note: The Platform Board and the standard USB
cable are supplied with the standard CY3632 WirelessUSB LS DVK (they are not included in the
CY3633 WirelessUSB LS Gaming DVK).
Figure 3. USB Hub Adapter Board installed into Platform Board (XBOX Receiver Dongle)
Joystick Knobs
XBOX USB Adapter
Cable
Standard
USB Cable
XBOX Game
Console
"XBOX G"
Chip
(No Chip)
Receiver/Dongle Platform Board
(without Joysticks or Potentiometers)
Game Controller Platform Board
(with Joysticks and Potentiometers)
USB Hub Adapter
Board with USB
Chip Installed

WirelessUSB™ LS Gaming DVK User’s Guide
Page -4 WirelessUSB™ LS Gaming DVK User’s Guide Rev 1.1
The Game Controller has a PSoC™ device labeled “XBOX G” installed into socket U3 of the Plat-
form Board. The Game Controller can be powered with batteries or the provided power supply
connected to J5 (DC power jack).
To configure the XBOX system, perform the following steps:
1. Power on the XBOX game console and load any XBOX game.
2. Install the USB Hub Adapter board as shown in Figure 3 above and ensure that the radio mod-
ule is installed in P1 correctly.
3. Connect the XBOX USB Adapter Cable to any of the four game ports on the XBOX Console.
4. Attach the “A” end of the standard USB cable to the other end of the XBOX USB Adapter
cable.
5. Connect the “B” end of the standard USB cable into Platform Board connector J3.
6. Verify that header J2 has pins 1 and 2 connected, which selects VBUS as the power source
for the board.
7. On the Game Controller board, verify that the radio and the proper PSoC™ adapter board are
installed on the board before power is supplied to the assembly. Verify that all eight potentiom-
eters, POT A-H, are turned fully counterclockwise.
8. If batteries are used as the power source, then install them now or plug in the DC power sup-
ply if batteries are not being used. Only one or the other can be used at a time. Ensure that
header J2 has pins 2 and 3 connected. This selects the battery or external DC power source.
9. Perform the binding procedure described in Section 2.3.
The figure below shows the PSoC Adapter Board that is used to adapt the 48-pin SSOP PSoC to
the 48-DIP socket on the platform board.
Figure 4. PSoC Adapter Board Assembly
CY8C27643 48-pin
SSOP PSoC
Pin 1
In System
Programming
Header
PSoC Adapter Board

WirelessUSB™ LS Gaming DVK User’s Guide Rev 1.1 Page -5
The mapping of the XBOX Game Controller joysticks, analog buttons, and digital buttons on the
Platform Board is shown in Figure 5. The eight potentiometers on the Platform Board act as analog
buttons, where clockwise rotation behaves as a depressed button, while fully counterclockwise
rotation behaves as a released button. The push-buttons that make up the Platform Board keypad
area are used for the Game Controller digital buttons as shown in the figure. Pressing the ‘Mode’
button will cause the ‘Right Joy button’ to activate the ‘R Trigger’ function in order to facilitate first
person shooter games. The ‘Connect’ LED flash rate will increase when in the button swap mode.
‘Reset Factory’ is used to clear all of the stored auto bind parameters and should be used when-
ever the radio module has been replaced. See Section 2.3 for more details.
Figure 5. XBOX Joysticks, Analog Buttons, and Digital Buttons
White
B
Y
A
X
R
Trigger
Black
L
Trigger
Left Joy
+
Left Joy
button
Right Joy
+
Right Joy
button
"Gamepad" area of Platform Board
Num
Lock
/*
-
7
Up +
Left
8
Up
9
Up +
Right
4
Left
56
Right
+
Start +
Back
1
Down +
Left
2
Down
3
Down+
Right
0
Select
.
Start
Enter
Mode
"Keypad" area of Platform Board
Reset
Factory

WirelessUSB™ LS Gaming DVK User’s Guide
Page -6 WirelessUSB™ LS Gaming DVK User’s Guide Rev 1.1
2.2 PlayStation2 Quick Start Guide
The PlayStation2 system hardware configuration is shown in Figure 6.
Figure 6. PlayStation2 System Hardware Configuration
The PlayStation2 gaming system uses the Platform Board assembly (121-07501*E) as the
receiver dongle. The PSoC chip labeled “PS2 D” should be installed in chip socket U3 of the
receiver dongle Platform Board. The PlayStation interface cable is used to interface the receiver
Platform Board assembly to the PS2 game console. The PS2 provides power through this cable to
the receiver assembly.
Figure 7. PS2 Interface Cable Connection Diagram
P layS tation2 Interface C able
PlayStation2 Game
Console
Game Controller Platform Board
(with Joysticks and Potentiometers)
Dongle/Receiver Platform Board
(without Joysticks or Potentiometers)
"PS2 G"
Module
"PS2 D"
Module
Joystick Knobs