d & b audiotechnik Y Series Quick start guide

YE7470/E7471
Rigging manual 1.1 en

S
y
m
b
o
l
s
o
n
t
h
e
p
r
o
d
u
c
t
P
l
e
a
s
e
r
e
f
e
r
t
o
t
h
e
i
n
f
o
r
m
a
t
i
o
n
i
n
t
h
e
m
a
n
u
a
l
.
W
A
R
N
I
N
G
!
D
a
n
g
e
r
o
u
s
v
o
l
t
a
g
e
!
General information
E7470/E7471 Rigging manual
Version: 1.1 en, 08/2014, D2709.EN .01
Copyright © 2014 by d&b audiotechnik GmbH; all rights
reserved.
Keep this manual with the product or in a safe place
so that it is available for future reference.
When reselling this product, hand over this manual to the new
customer.
If you supply d&b products, please draw the attention of your
customers to this manual. Enclose the relevant manuals with the
systems. If you require additional manuals for this purpose, you
can order them from d&b.
d&b audiotechnik GmbH
Eugen-Adolff-Strasse 134, D-71522 Backnang, Germany
T [phone], F [phone]
[email protected], www.dbaudio.com

1. E7470/E7471 Y Touring carts..................................... 4
1.1. Intended use................................................................ 4
1.2. Scope of supply........................................................... 4
1.3. Weights and dimensions............................................. 5
1.4. Additional top loads.................................................... 5
1.5. Loading the cabinets onto the cart............................. 6
Contents
d&b E7470/E7471 Rigging manual 1.1 en 3

1.1. Intended use
The E7470 and E7471 Y Touring carts are intended to store and
transport 4 x Y8/Y12 (E7470) or 8 x Y8/Y12 (E7471) cabinets,
respectively.
The entire cabinet assembly stored in the cart can be directly
connected to the Y Flying frame or mounted below already
suspended Y8/Y12 or Y-SUB cabinets.
A detailed description of the assembly and disassembly of Y-Series
arrays in conjunction with the Y Touring carts is given in the Y-
Series Rigging manual which is provided with the Y Flying frame.
1.2. Scope of supply
Delivery state
The Y-Series Touring carts are supplied in a dismantled state as
shown in the graphic opposite.
Note: This is also a space-saving way to store the carts on
site during an event.
Please verify the shipment for completeness and proper condition
of the items.
Qty. d&b Code Description
1 E7470 d&b Touring cart 4 x Y8/Y12
1 E7471 d&b Touring cart 8 x Y8/Y12
Each including:
1 Bottom tray with wheels [1] (specific to
cart).
4 Connecting poles [2] equipped with two
fasteners (CamLocks) [F] each.
1 Top lid [3] (specific to cart).
1 D2709.EN .01 Rigging manual
E7470 and E7471 Y Touring carts
[1]
[2]
[3]
[F]
Y Touring carts, scope of supply
Shown: E7470 Touring cart 4 x Y8/Y12
1. E7470/E7471 Y Touring carts
d&b E7470/E7471 Rigging manual 1.1 en4

1.3. Weights and dimensions
Total weight including cabinets:
E7470 130 kg ( 285 lb)
E7471 230 kg ( 510 lb)
E7470 and E7471 dimensions in mm [inch]
1.4. Additional top loads
CAUTION!
Possible risk of personal injury and/or
damage to material!
Observe the maximum permitted top load as indicated on the
corresponding instruction label of the cart:
–E7470 - 100 kg (220 lb)
–E7471 - 200 kg (440 lb)
These additional top loads are only permitted during transport
provided the loads are secured against movement and tipping
over.
Any additional top load must be removed before moving the carts
when unloading or moving them to the assembly position.
d&b E7470/E7471 Rigging manual 1.1 en 5

1.5. Loading the cabinets onto the cart
Order of assembly
The bottom tray and the top lid of a cart are interconnected by four
connecting poles, which are equipped with two fasteners
(CamLocks) each.
Note: To prevent the connecting poles from any damage
when loading the cabinets on the cart, we recommend you to
attach the poles only after the cart is fully loaded.
1. Place the first cabinet on the bottom tray.
2. At the front release the Locking pins of the Front links.
Þ The Front links will slide out automatically.
3. On the rear release both Locking pins and fold out the Splay
link.
4. Reinsert the Locking pins.
6. Prepare the Front and Splay links of the next cabinet in the
same manner as described for the first cabinet.
7. Attach the prepared cabinet to the corresponding slots at the
front of the bottom cabinet.
8. Insert and lock the Locking pins of the cabinet's Front links on
both sides.
9. Add the remaining two cabinets in the same manner until the
assembly is completed.
d&b E7470/E7471 Rigging manual 1.1 en6

10. Attach the poles to the bottom tray and lock all fasteners
(CamLocks).
11. Attach the top lid and lock all fasteners (CamLocks).
Note: The top lids of the touring carts are equipped with
additional guiding tracks to fix the cabinet assemblies in place.
In conjunction with the E7470 Touring cart 4 x Y8/Y12
observe the direction of attachment as shown in the graphic
below.
d&b E7470/E7471 Rigging manual 1.1 en 7

D2709.EN .01, 08/2014 © d&b audiotechnik GmbH
www.dbaudio.com