D-Link DI-624S - AirPlus Xtreme G Wireless 108G USB Storage... User manual

2 D-Link Systems, Inc.
DI-624S Install GuideSystem Requirements
System Requirements
Minimum System Requirements:
 Cable or DSL Modem with an Ethernet Port
 Windows XP/2000 or MAC OS X (10.3,10.2,10.1) PC with at least:
• 200MHz Processor
• 64MB Memory
• CD-ROM Drive
• Ethernet Adapter with TCP/IP Protocol Installed
 Internet Explorer Version 6.0 or Netscape Navigator Version 7.0
Package Contents

D-Link Systems, Inc. 3
DI-624S Install Guide Hardware Overview
Hardware Overview
Front Panel
Local Network LEDs
A solid light on the port indicates a
connection to an Ethernet enabled
computer on ports 1-4. This LED
blinks during data transmission.
WLAN LED
A solid light indicates that the
wireless segment is ready. This
LED blinks during wireless data
transmission.
WAN LED
A solid light indicates a connection
on the WAN port. This LED blinks
during data transmission.
Power LED
A solid light indicates
a proper connection
to the power supply.
Status LED
A blinking light indicates
that the DI-624S is
functioning properly.
USB LEDs
A solid light indicates a
connection on the USB
port. This LED blinks during
data transmission.

4 D-Link Systems, Inc.
DI-624S Install GuideHardware Overview
Rear Panel
LAN Ports
These are the connections for the
Ethernet cables to Ethernet enabled
computers.
USB 2.0 Ports
Use these ports to connect USB 2.0
devices. USB 1.1 devices may also be
connected but will be limited to USB
1.1 speed.
Reset Button
Pressing this button restores the
Router to its original factory default
settings.
WAN Port
This is for the connection of an
Ethernet cable to the Cable or
DSL modem.
Power Receptor
This is for the connection of
a Power Adapter.

D-Link Systems, Inc. 5
DI-624S Install Guide Installation Overview
Installation Overview
Once you’ve completed your DI-624S installation, your network should appear
similar to the diagram below.

6 D-Link Systems, Inc.
DI-624S Install GuideInstalling the Hardware
Installing the Hardware
1
Plug the AC adapter into the receptor located on the back
panel of the DI-624S.
2
Plug the other end of the AC adapter into a power strip
or wall outlet. The Power LED on the DI-624S will turn
ON to indicate proper operation.

D-Link Systems, Inc. 7
DI-624S Install Guide Installing the Hardware
3(A) Power off your Cable or DSL modem; some devices
may not have an on/off switch, which will require you
to unplug the power adapter. At this point, the DI-624S
should be powered on and the Cable/DSL modem should
be turned off.
(B) Cable/DSL modem (Power OFF) - DI-624S (Power ON)
Connect an Ethernet cable to the Ethernet jack located on
the Cable/DSL modem. After the Ethernet cable is securely
connected, power on the Cable/DSL modem by pressing
the power button or plugging in the power adapter.
(C) Cable/DSL modem (Power ON) - DI-624S (Power ON)
Insert the other end of the Ethernet cable into the WAN
PORT on the back panel of the DI-624S. The WAN LED
light will illuminate to indicate proper connection. If the WAN
LED is not illuminated, please go back to STEP (3-A) and
repeat the instructions.
4
Insert an Ethernet cable into LAN port 1 on the back panel
of the DI-624S. Note: the LAN ports on the DI-624S are
Auto-MDI/MDIX, meaning you can use straight-through or
crossover Ethernet cable to the LAN ports.

8 D-Link Systems, Inc.
DI-624S Install GuideUsing the Setup Wizard
Type ”admin” for the username and
leave the password blank.
Click OK
Once you have logged in, the
Home screen will appear.
Click Run Wizard
The logon pop-up screen will appear.
Open your Web browser and type
“http://192.168.0.1” into the URL
address box. Then press the Enter
or Return key.
Using the Setup Wizard
admin

D-Link Systems, Inc. 9
DI-624S Install Guide The Setup Wizard (continued)
Click Next
Click Next
Click Next
You will see the following screens.
Setup your new password.
You have the option to establish
a password.
Choose your time zone from
the drop down list.

10 D-Link Systems, Inc.
DI-624S Install GuideThe Setup Wizard (continued)
Click Next
Click Next
Click Next
Select your internet connection.
You will be prompted to select the
type of Internet connection for your
router.
If you selected Dynamic IP Address,
this screen will appear: (Used mainly
for Cable Internet Service.)
If your ISP requires a Static IP
Address, and this option is selected,
then this screen will appear:
Enter the IP address information
originally provided to you by your
ISP. You will need to complete all the
required fields.
Please continue to Wireless Setup on page 12
Please continue to Wireless Setup on page 12
This setup should be done on
the computer that was originally
connected to your modem.
If you are unsure of which
setting to select, please contact
your Internet Service Provider.