D-Link DIR-320 User manual

WIRELESS G ROUTER
DIR-320
Quick Installation Guide+

This product can be set up using
any current web browser:
Internet Explorer 6 or Netscape
Navigator 7
DIR-320
Wireless G Router
5V 2A DC Power Adapter
©2004 D-Link Systems, Inc. All rights reserved. Trademarks or registered trademarks are the property of their respective
holders. Software and specications subject to change without notice.
Before You Begin
1. If you purchased this router to share your high-speed Internet connection with
other computers, you must have either an Ethernet-based Cable or DSL modem
with an established Internet account from an Internet Service Provider (ISP).
2. It’s best to use the same computer that is connected to your modem for conguring
the DIR-320 Wireless G Router. The DIR-320 acts as a DHCP server and will
assign all the necessary IP address information on your network. See Appendix at
the end of this Quick Installation Guide for setting each network adapter to
automatically obtain an IP address.
Check Your Package Contents
DIR-320 Wireless G Router
Ethernet (CAT5 UTP/Straight Through) Cable
Using a power
supply with a different
voltage rating will
damage and void the
warranty of this product.
If any of the above items are missing, please contact your reseller.

3
Connecting The DIR-320 Wireless
Router To Your Network
A. Receptor for
Power Adapter.
Reset Button
Pressing this button restores the Router to its original
factory default settings.
A. First, connect the power adapter to the receptor at the back panel of the
DIR-320 and then plug the other end of the power adapter to a wall outlet or power
strip. The Power LED lights up indicating proper operation.
B. 1. Power off your Cable or DSL modem; devices that do not have a on/off switch and
will require you to unplug the power adapter. Now, the DIR-320 should be powered on
and the Cable / DSL modem should be turned off.
Cable / DSL modem (Power Off) – DIR-320 (Power On)
2. Connect an Ethernet cable to the Ethernet jack located on the Cable / DSL modem.
After the Ethernet cable is securely connected, power on the Cable / DSL modem by
turning on the unit or plugging in the power adapter.
Cable / DSL modem (Power On) – DIR-320 (Power On)
3. Insert the other end of the Ethernet cable to the WAN PORT on the back panel of
the DIR-320. The WAN LED light will illuminate to indicate proper connection. If the
WAN LED is not illuminated, please go back to step B1 and repeat the steps.
C. Insert an Ethernet cable to LAN Port 1 on the back panel of the DIR-320 and an
available Ethernet port on the network adapter in the computer you are using to
congure the DIR-320. The LED light for LAN Port 1 illuminates to indicate proper
connection. (Note: The LAN Ports on the DIR-320 are Auto-MDI/MDI-X. Meaning you
can use a straight-through or crossover-Ethernet cable in the LAN Ports.)
D. Computers equipped with 802.11g wireless adapters will be able to connect to the
DIR-320.
B. WAN PORT
This is for the connection
of an Ethernet cable to the
Cable or DSL modem.
D. Antenna
Used to wirelessly
connect to 802.11g
or 802.11b
adapters.
C. LAN PORTS
These are the
connections for Ethernet
cables to Ethernet
enabled computers.
USB PORT

4
Restart Your Computer
Connecting Additional Computers
To The DIR-320
LOCAL NETWORK LEDs – a
solid light on the port indicates
a connection to an Ethernet
enabled computer on ports 1-4.
This LED blinks during data
transmission.
Power LED – a solid
light indicates a proper
connection to the power
supply.
Status LED – a blinking light
indicates that the DIR-320 is
functioning properly.
When you have completed the steps in this Quick Installation Guide, your connected
network should look similar to this:
Using additional Ethernet (CAT5 UTP) cables, connect your Ethernet-equipped
computers to the remaining Ethernet LAN ports on the back panel of the DIR-320.
Internet LED – a solid
light indicates connection
on the WAN port. This
LED blinks during data
transmission.
WLAN LED – a solid light
indicates that the wireless
segment is ready. This
LED blinks during wireless
data transmission.
USB LED – a solid light
indicates connection to
an USB printer device.

5
Using The Internt Connection
Setup Wizard
The logon pop-up screen will appear.
Open your Web browser and
type “http://192.168.0.1” into the
URL address box. Then press the
Enter or Return key.
Type “admin” for the username and
leave the password eld blank.
Click Log In
Click Internet Connection
Setup Wizard
Once you have logged in, the Setup screen will appear.

6
The Internet Connection Setup
Wizard (Continued)
You will see the following screens:
Set up your new password.
You have the option to establish
a password.
Click Next
Choose your time zone from
the drop down list.
Click Next
Click Next

7
If you selected Dynamic IP Address, this
screen will appear: (Used mainly for Cable
Internet service.)
Click the “Clone MAC Address”
button to automatically copy the
MAC address of the network
adapter in your computer. You
can also manually type in the
MAC address.
The Internet Connection Setup
Wizard (Continued)
Select your Internet
Connection. You
will be prompted to
select the type of
Internet connection
for your router.
If you are unsure
of which setting
to select, please
contact your Internet
Service Provider.
Click Next
Click Next
This setup should be done on
the computer that is registered
on the ISP’s network.
Otherwise, you will see the following screen:

8
The Internet Connection Setup
Wizard (Continued)
If your ISP requires a Static IP Address, and this option is selected, then this screen
will appear:
Enter the IP address information originally provided to you by your ISP. You will need
to complete all the required elds.
Click Next
If your ISP uses PPPoE (Point-to-Point Protocol over Ethernet), and this option is
selected, then this screen will appear: (Used mainly for DSL Internet service.)
Please be sure to
remove any existing
PPPoE client
software installed on
your computers.
Enter in the username and password provided to you by your ISP.
Click Next

9
Click Connect
The Internet Connection Setup
Wizard (Continued)

10
Using The Wireless Connection
Setup Wizard
In the wireless connection section, you can start the wireless setting in the wireless
conncetion setup wizard.
You will see the following screens:
Click Next
Click Wireless Connection
Setup Wizard

11
The Wireless Connection Setup
Wizard (Continued)
Set up your new SSID.
Your 802.11g wireless network are
SSID:dlink
Choose your encryption type. The DIR-320 is capable of three levels of wireless
encryption-Good, Better and Best By default the encryption is none. You can change
the encryption settings for more secure wireless communication.
Click Next
Click Next

12
Click Save
Test Internet Connection
You will be returned to the Setup tab.
For additional settings
or information, refer to
the Advanced, Tools,
or Status tabs on the
web-management
interface.
Then relaunch your Web browser (i.e., Internet Explorer or Netscape Navigator), to
link to your favorite Web site to test your Internet connection.
The Wireless Connection Setup
Wizard (Continued)
You can review the wireless setting before conrmation.

13
To connect to the network, make sure the
network adapter in your computer is congured
properly. Here’s how to congure the network
adapter to obtain an IP address automatically
for the DIR-320 Wireless Broadband Router.
APPENDIX
Restart your computer (if necessary)
Click OK
Select Obtain an IP address
automatically
Click Internet Protocol (TCP/IP)
Click Properties
For Microsoft Windows XP:
right click on My Network Places
icon on the desktop > select
Properties > Double-click on the
Network Connection associated
with the Ethernet adapter
(i.e., D-Link DFE-530TX+).

14
For Apple Macintosh OS X:
The IP address information,
the Subnet Mask, the Router’s
IP address and the Ethernet
adapter address will appear.
Click on
Network
Select Using DHCP
in the Congure pull
down menu
Go to the Apple Menu Click
on System Preferences and
Select Network.
Click on Apply Now
Select Built-in Ethernet
in the Show pull down
menu

Technical Support
You can nd software updates and user documentation on the D-Link website.
Tech Support for customers in
Australia:
Tel: [phone]
Monday to Friday 8:00am to 8:00pm EST
Saturday 9:00am to 1:00pm EST
http://www.dlink.com.au
e-mail: [email protected]
India:
Tel: [phone]
Monday to Friday 9:30AM to 7:00PM
http://www.dlink.co.in/support/productsupport.aspx
Indonesia, Malaysia, Singapore and Thailand:
Tel: [phone] (Indonesia)
Tel: [phone] (Malaysia)
Tel: [phone] (Singapore)
Tel: [phone] (Thailand)
Monday to Friday 9:00am to 6:00pm
http://www.dlink.com.sg/support/
e-mail: [email protected]
Korea:
Tel: [phone]
Monday to Friday 9:00am to 6:00pm
http://www.d-link.co.kr
e-mail: [email protected]
New Zealand:
Tel: [phone]
Monday to Friday 8:30am to 8:30pm
Saturday 9:00am to 5:00pm
http://www.dlink.co.nz
e-mail: [email protected]

Technical Support
You can nd software updates and user documentation on the D-Link website.
Tech Support for customers in
Egypt:
Tel: [phone] or [phone]
Sunday to Thursday 9:00am to 5:00pm
http://support.dlink-me.com
e-mail: [email protected]
Iran:
Tel: [phone]
Sunday to Thursday 9:00am to 6:00pm
http://support.dlink-me.com
e-mail: [email protected]
Israel:
Tel: [phone]
Sunday to Thursday 9:00am to 5:00pm
http://www.dlink.co.il/support/
e-mail: [email protected]
Pakistan:
Tel: [phone] or [phone]
Sunday to Thursday 9:00am to 6:00pm
http://support.dlink-me.com
e-mail: [email protected]
South Africa and Sub Sahara Region:
Tel: [phone]
08600 DLINK (for South Africa only)
Monday to Friday 8:30am to 9:00pm South Africa Time
http://www.d-link.co.za
Turkey:
Tel: [phone]
Monday to Friday 9:00am to 6:00pm
http://www.dlink.com.tr
e-mail: [email protected]
e-mail: [email protected]
U.A.E and North Africa:
Tel: [phone] (U.A.E)
Sunday to Wednesday 9:00am to 6:00pm GMT+4
Thursday 9:00am to 1:00pm GMT+4
http://support.dlink-me.com
e-mail: [email protected]

Ver. 1.10(I)
2008/01/23
6DIR320QML01G