D-Link DIR-632 User manual

Quick Installation Guide
DIR-632
Multifunction Wireless Router
Supporting WiMAX, 3G GSM/CDMA
wit Built-in 8-port Switc

DIR-632 Quick Installation Guide
BEFORE YOU BEGIN
Delivery Package
•Wireless router DIR-632
•Power adapter DC 5V/2.5A
•Straight-through thernet cable (CAT 5 )
•CD-ROM with “User Manual” and “Quick Installation Guide”
•“Quick Installation Guide” (brochure)
If any of the items are missing, please contact your reseller.
!Using a power supply with a different voltage rating than the one
included will cause damage and void the warranty for this product.
Default Settings
IP address o wireless router 192.168.0.1
Username (login) admin
Password admin
Name o wireless network (SSID) DIR-632
2

DIR-632 Quick Installation Guide
System Requirements and Equipment
•A computer with any operating system that supports a web browser.
•A web browser to access the web-based interface of the router: Windows
Internet xplorer, Mozilla Firefox, or Opera.
•A NIC ( thernet or Wi-Fi adapter) to connect to the router.
•An 802.11b, g, or n Wi-Fi adapter to create a wireless network.
•A USB modem to connect to the Internet1.
◦A WiMAX USB modem to connect to the Internet via a WiMAX
network.
!
Some WiMAX operators require subscribers to activate their WiMAX
USB modems prior to using them. Please, refer to connection
guidelines provided by your operator when concluding the agreement
or placed on its website.
◦A 3G USB modem to connect to the Internet via a 3G GSM or
CDMA network.
!
Your USB modem should be equipped with an active identification
card (SIM or R-UIM) of your operator.
It is recommended to disable the PIN code check on the identification
card prior to connecting the USB modem to the router.
1 Contact your operator to get information on the service coverage and fees.
3

DIR-632 Quick Installation Guide
Supported USB Modems
GSM modems
•Huawei 150
•Huawei 1550
•Huawei 160G
•Huawei 169G
•Huawei 173
•Huawei 220
•ZT MF112
•ZT MF192
•ZT MF626
•ZT MF627
•ZT MF652.
CDMA modems
•Anydata ADU-500A
•Celot CT-650.
WiMAX modem
•Samsung SWC-U200 (firmware version u200_rev1-2.7.40-CI14).
!The manufacturer does not guarantee proper operation of the router
with every modification of the firmware of USB modems.
4

DIR-632 Quick Installation Guide
CONNECTING TO PC (OS WINDOWS XP)
PC wit Et ernet Adapter
1. Make sure that your PC is powered off.
2. Connect an thernet cable between any of LAN ports located on the back
panel of the router and the thernet port of your PC.
3. To connect via a WiMAX, 3G GSM or CDMA network: connect your
USB modem to the USB port2 located on the back panel of the router.
!
If you need to connect or change a USB modem to another one when
the router is powered on, power off the router, connect the modem to
the USB port, and power on the router.
4. Connect the power cord to the power connector port on the back panel of
the router, then plug the power adapter into an electrical outlet or power
strip.
5. Turn on your PC and wait until your operating system is completely
loaded.
Now you should configure your PC to obtain an IP address automatically (as
DHCP client).
1. Click the Start button and proceed to the Control Panel > Network
and Internet Connections > Network Connections window.
2 It is recommended to use a USB extension cable to connect a USB modem to the
router.
5

DIR-632 Quick Installation Guide
2. In the Network Connections window, right-click the relevant Local
Area Connection icon and select the Properties line in the menu
displayed.
3. In the Local Area Connection Properties window, on the General
tab, in the This connection uses the ollowing items section, select
the Internet Protocol (TCP/IP) line. Click the Properties button.
6

DIR-632 Quick Installation Guide
4. Select the Obtain an IP address automatically radio button. Click
the OK button.
Click the ОК button. Now your computer is configured to obtain an IP address
automatically.
7

DIR-632 Quick Installation Guide
PC wit Wi-Fi Adapter
1. To connect via a WiMAX, 3G GSM or CDMA network: connect your
USB modem to the USB port3 located on the back panel of the router.
!
If you need to connect or change a USB modem to another one when
the router is powered on, power off the router, connect the modem to
the USB port, and power on the router.
2. Connect the power cord to the power connector port on the back panel of
the router, then plug the power adapter into an electrical outlet or power
strip.
3. Turn on your PC and wait until your operating system is completely
loaded.
4. Turn on your Wi-Fi adapter. As a rule, modern notebooks with built-in
wireless NICs are equipped with a button or switch that turns on/off the
wireless adapter (refer to your PC documents). If your PC is equipped
with a pluggable wireless NIC, install the software provided with your
Wi-Fi adapter.
3 It is recommended to a use USB extension cable to connect a USB modem to the
router.
8

DIR-632 Quick Installation Guide
Now you should configure your Wi-Fi adapter.
1. Click the Start button and proceed to the Control Panel > Network
and Internet Connections > Network Connections window.
2. Select the icon of the wireless connection and make sure that your Wi-Fi
adapter is on.
3. Search for available wireless networks.
4. In the opened Wireless Network Connection window, select the
needed wireless network (DIR-632) and click the Connect button.
After that the Wireless Network Connection Status window appears.
9

DIR-632 Quick Installation Guide
CONFIGURING ROUTER
Connecting to Web-based Interface
1. Start a web browser.
2. In the address bar of the web browser, enter the IP address of the router
(by default, the following IP address is specified: 192.168.0.1). Press
the Enter key.
3. On the opened page, enter the username (login) and password for the
administrator account (by default, the following username and password
are specified: admin, admin). Then click the Enter link.
!
If the error “ The page cannot be displayed ” (or “ Unable to display the
page ”/“ Could not connect to re ote server ”) occurs upon connecting to
the web-based interface of the router, make sure that you have properly
connected the router to your computer.
10

DIR-632 Quick Installation Guide
Right after the first access to the web-based interface you are forwarded to the
page for changing the administrator password specified by default.
nter the new password in the Password and Con irmation fields. Then
click the Save button.
!
Remember or write down the new password for the administrator
account. In case of losing the new password, you can access the settings
of the router only after restoring the factory default settings via the
hardware Reset button. This procedure wipes out all settings that you
have configured for your router.
11

DIR-632 Quick Installation Guide
After successful registration the router's quick settings page opens.
On the page, you can proceed to the Wizards (use the Connect to internet,
Host site, and Con igure Wi-Fi buttons) or switch to the standard web-
based interface of the router by clicking the Con igure manually button.
After clicking the button, the system statistics page opens. The page displays
general information on the router and its software.
The web-based interface of the router is multilingual. Select a needed language
from the menu displayed when the mouse pointer is over the Language
caption. You can change the language of the web-based interface in any menu
item.
After selecting the language, the notification on unsaved changes will be
displayed. Click the Save button to save the current language of the web-
based interface as the default language.
12

DIR-632 Quick Installation Guide
Configuring Connection to t e Internet
!
You should configure your WAN connection in accordance with data
provided by your Internet service provider (ISP). Make sure that you
have obtained all necessary information prior to configuring your
connection. Otherwise contact your ISP.
WiMAX WAN Connection
1. If your operator specified an identifier for the WiMAX network, proceed
to the WiMAX / In ormation page, enter the required value in the SSID
field and click the Connect button.
2. Go to the Net / WAN page and click the Add button.
3. In the General settings section, leave the Manual value.
4. From the Connection Type drop-down list, select the needed value.
5. From the Port drop-down list, select the USB-WIMAX value.
6. Specify a name for your connection (any name for easier identification) in
the Name field.
7. For connection of PPPoE type: in the PPP section, enter authorization
data provided by your ISP (the username (login) in the PPP Username
field and the password in the Password and Password con irmation
fields), or select the Without authorization checkbox if authorization
is not required.
8. For connection of Static IP type: in the IP section, fill in the IP
Address, Netmask, Gateway IP Address, and Primary DNS
server fields.
9. For connection of Dynamic IP type: if your ISP has provided the address
of the DNS server, in the IP section, deselect the Obtain DNS server
addresses automatically checkbox and fill in the Primary DNS
server field.
13

DIR-632 Quick Installation Guide
10. For connection of PPTP + Static IP or L TP + Static IP type: in the IP
section, fill in the IP Address, Netmask, Gateway IP Address, and
Primary DNS server fields. Then in the VPN section, enter
authorization data provided by your ISP (the username (login) in the PPP
Username field and the password in the Password and Password
con irmation fields), or select the Without authorization checkbox if
authorization is not required. In the VPN server address field, enter
the IP or URL address of the PPTP or L2TP authentication server. If your
ISP applies encryption, select a needed value from the Encryption drop-
down list.
11. For connection of PPTP + Dynamic IP or L TP + Dynamic IP type: if
your ISP has provided the address of the DNS server, in the IP section,
deselect the Obtain DNS server addresses automatically
checkbox and fill in the Primary DNS server field. Then in the VPN
section, enter authorization data provided by your ISP (the username
(login) in the PPP Username field and the password in the Password
and Password con irmation fields), or select the Without
authorization checkbox if authorization is not required. In the VPN
server address field, enter the IP or URL address of the PPTP or L2TP
authentication server. If your ISP applies encryption, select a needed
value from the Encryption drop-down list.
12. Click the Save button.
13. On the Net / WAN page, select the choice of the De ault gateway
radio button corresponding to the new WiMAX WAN connection.
14

DIR-632 Quick Installation Guide
3G WAN Connection
If the PIN code check is enabled for the SIM card inserted into your USB
modem, then prior to creating a 3G WAN connection, proceed to the USB
modem menu and enter the PIN code on the page displayed.
1. Go to the Net / WAN page and click the Add button.
2. In the General settings section, from the Provider drop-down list,
select your country and operator to automatically specify all settings
required to connect to the Internet. To specify all settings independently,
leave the Manual value.
3. From the Connection Type drop-down list, select the 3G value.
4. From the Port drop-down list, select the USB value.
5. Specify a name for your connection (any name for easier identification) in
the Name field.
6. If you need to specify other settings, in the PPP Settings section, enter
authorization data provided by your operator (the username (login) in the
PPP Username field and the password in the Password and
Password con irmation fields), or select the Without
authorization checkbox if authorization is not required. In the APN
field, enter the access point name, and in the Dial number field, enter
the number dialed to connect to the authorization server of the operator.
7. Click the Save button.
8. On the Net / WAN page, select the choice of the De ault gateway
radio button corresponding to the new 3G WAN connection.
15

DIR-632 Quick Installation Guide
Wired WAN Connection
1. Go to the Net / WAN page, select the WAN connection and click the
Delete button.
2. Click the Add button.
3. In the General settings section, leave the Manual value.
4. From the Connection Type drop-down list, select the needed value.
5. From the Port drop-down list, select the Internet value.
6. Specify a name for your connection (any name for easier identification) in
the Name field.
7. If your ISP uses MAC address binding, in the Ethernet section, in the
MAC field, enter the MAC address registered by your ISP upon
concluding the agreement. To set the MAC address of the network
interface card (of the computer that is being used to configure the router
at the moment) as the MAC address of the WAN interface, click the
Clone MAC button. To set the address of a device connected to the
router's LAN at the moment, select the relevant value from the drop-down
list located to the right of the field.
8. For connection of PPPoE type: in the PPP section, enter authorization
data provided by your ISP (the username (login) in the PPP Username
field and the password in the Password and Password con irmation
fields), or select the Without authorization checkbox if authorization
is not required.
9. For connection of Static IP type: in the IP section, fill in the IP
Address, Netmask, Gateway IP Address, and Primary DNS
server fields.
10. For connection of Dynamic IP type: if your ISP has provided the address
of the DNS server, in the IP section, deselect the Obtain DNS server
addresses automatically checkbox and fill in the Primary DNS
server field.
16

DIR-632 Quick Installation Guide
11. For connection of PPTP + Static IP or L TP + Static IP type: in the IP
section, fill in the IP Address, Netmask, Gateway IP Address, and
Primary DNS server fields. Then in the VPN section, enter
authorization data provided by your ISP (the username (login) in the PPP
Username field and the password in the Password and Password
con irmation fields), or select the Without authorization checkbox if
authorization is not required. In the VPN server address field, enter
the IP or URL address of the PPTP or L2TP authentication server. If your
ISP applies encryption, select a needed value from the Encryption drop-
down list.
12. For connection of PPTP + Dynamic IP or L TP + Dynamic IP type: if
your ISP has provided the address of the DNS server, in the IP section,
deselect the Obtain DNS server addresses automatically
checkbox and fill in the Primary DNS server field. Then in the VPN
section, enter authorization data provided by your ISP (the username
(login) in the PPP Username field and the password in the Password
and Password con irmation fields), or select the Without
authorization checkbox if authorization is not required. In the VPN
server address field, enter the IP or URL address of the PPTP or L2TP
authentication server. If your ISP applies encryption, select a needed
value from the Encryption drop-down list.
13. Click the Save button.
17

DIR-632 Quick Installation Guide
Configuring Local Area Network
1. Go to the Net / LAN page. If needed, change the IP address of the
router's LAN interface and the mask of the local subnet in the IP
Address and Netmask fields of the IP section. Then click the Save
button.
2. By default, the DHCP server of the router is enabled. In the DHCP
server section you can change the parameters of the DHCP server. If
you want to manually assign IP addresses to devices of your LAN,
disable the DHCP server (select the Disable value from the Mode drop-
down list).
3. After specifying the DHCP server settings, click the Save button.
18

DIR-632 Quick Installation Guide
Configuring Wireless Network
By default, the wireless network of the router is open (it requires no password
to access it). To avoid unauthorized access to your wireless local area network,
change the default settings of the router.
Example of Wireless Settings
1. Go to the Wi-Fi / Security settings page.
2. Select the WPA2-PSK value from the Network Authentication drop-
down list.
3. nter a key (a password that will be used to access your wireless
network) in the Encryption Key PSK field. Use digits and Latin
characters.
4. Select the AES value from the WPA Encryption drop-down list.
5. Click the Change button.
!
If you perform initial configuration of the router via Wi-Fi connection,
note that immediately after changing the wireless default settings you
will need to reconfigure the wireless connection using the newly
specified settings.
19

DIR-632 Quick Installation Guide
Saving Settings to Non-volatile Memory
In order to avoid losing the new settings upon hardware reboot (accidental or
intentional power-off of the device), it is recommended to save the settings to
the non-volatile memory of the router.
Click the Save&Reboot line in the top-page menu displayed when the mouse
pointer is over the System caption.
Wait until the router is rebooted. Now you can use it to access the Internet or
access the web-based interface of the router to configure additional parameters
(for detailed description of every page of the web-based interface, see the
“User Manual” document).
20