D-Link DSL-2730E User manual

D-Link DSL-2730E
Wireless N 150 ADSL2+ Modem Router
User Manual
RECYCLABLE
2014/08/14
Ver. 1.00

DSL-2730E User Manual
Contents
1Introduction......................................................................................................1
1.1 Packing List......................................................................................... 1
1.2 Safety Precautions .............................................................................. 1
1.3 LEDs and Interfaces............................................................................ 2
1.4 System Requirements ......................................................................... 4
1.5 Features.............................................................................................. 4
2Hardware Installation....................................................................................... 6
3Web Configuration........................................................................................... 7
3.1 Accessing the Device .......................................................................... 7
3.2 Setup ..................................................................................................9
3.2.1 Wizard................................................................................. 9
3.2.2 Local Network.................................................................... 15
3.2.3 Internet Setup.................................................................... 24
3.2.4 Wireless Setup .................................................................. 31
3.2.5 Time and Date................................................................... 36
3.3 Advanced .......................................................................................... 37
3.3.1 Advanced Wireless............................................................ 38
3.3.2 Access Control List............................................................ 43
3.3.3 Port Triggering................................................................... 46
3.3.4 Port Forwarding................................................................. 48
3.3.5 DMZ .................................................................................. 49
3.3.6 Parental Control ................................................................ 49
3.3.7 Filtering Options ................................................................ 52
3.3.8 DoS Settings ..................................................................... 55
3.3.9 DNS .................................................................................. 56
3.3.10 Dynamic DNS.................................................................... 58
3.3.11 Network Tools.................................................................... 60
3.3.12 Routing.............................................................................. 72
3.3.13 NAT ................................................................................... 76
3.4 Maintenance ..................................................................................... 80
3.4.1 System .............................................................................. 80
3.4.2 Firmware Update............................................................... 82
3.4.3 Password .......................................................................... 82
i

DSL-2730E User Manual
3.4.4 Diagnostics........................................................................ 83
3.4.5 System Log ....................................................................... 86
3.4.6 Logout ............................................................................... 88
3.5 Status ................................................................................................ 88
3.5.1 Device Info ........................................................................ 88
3.5.2 Wireless Clients................................................................. 90
3.5.3 DHCP Clients .................................................................... 90
3.5.4 ADSL Driver ...................................................................... 91
3.5.5 Statistics............................................................................ 91
3.5.6 Route Info.......................................................................... 92
3.6 Help .................................................................................................. 93
ii

DSL-2730E User Manual
1 Introduction
The DSL-2730E supports multiple line modes. With four 10/100 base-T Ethernet
interfaces at the user end, the device provides high-speed ADSL broadband
connection to the Internet or Intranet for high-end users like net bars and office
users. It provides high performance access to the Internet with a downstream
rate of 24 Mbps and an upstream rate of 1 Mbps. It supports IPV6.
The device supports WLAN access, such as WLAN AP or WLAN device, to the
Internet. It complies with specifications of IEEE 802.11, 802.11b/g/n, WEP, WPA,
and WPA2 security. The WLAN of the device supports 1T1R.
1.1 Packing List
1 x DSL-2730E
1 x external splitter
1 x power adapter
1 x telephone cables (RJ-11)
1 x Ethernet cable (RJ-45)
1 x QIG
1.2 Safety Precautions
Take the following instructions to prevent the device from risks and damage
caused by fire or electric power:
Use the type of power marked in the volume label.
Use the power adapter in the product package.
Pay attention to the power load of the outlet or prolonged lines. An
overburden power outlet or damaged lines or plugs may cause electric
shock or fire accidents. Check the power cords regularly. If you find any
damage, replace it at once.
Proper space left for heat dissipation is necessary to avoid damage
caused by overheating to the device. The long and thin holes on the device
are designed for heat dissipation to ensure that the device works normally.
Do not cover these heat dissipation holes.
1

DSL-2730E User Manual
Do not put this device close to a heat source or under a high temperature
occurs. Keep the device away from direct sunshine.
Do not put this device close to an overdamp or watery place. Do not spill
fluid on this device.
Do not connect this device to a PC or electronic product unless instructed
by our customer engineer or your broadband provider. Wrong connection
may cause power or fire risk.
Do not place this device on an unstable surface or support.
1.3 LEDs and Interfaces
Note:
The figures in this document are for reference only.
Front Panel
Figure 1 Front panel
The following table describes the LEDs of the device.
LED
Color
Status
Description
Power
Green
Off
The power is off.
On The power is on and the initialization is
normal.
Red
On
The device is initiating.
Blinks
The firmware is upgrading.
LAN 1/2/3/4 Green
Off
No LAN link.
Blinks
Data is being transmitted through the
LAN interface.
On
The connection of LAN interface is
normal.
2

DSL-2730E User Manual
LED
Color
Status
Description
WLAN
Green
Blinks Data is transmitted through the WLAN
interface.
On
The connection of WLAN interface is
normal.
Off The WLAN connection is not established.
WPS Blue
Blinks WPS negotiation is enabled, waiting for
the clients.
Off WPS negotiation is not enabled on the
device.
DSL Green
Off
Initial self-test is failed.
Blinks
The device is detecting itself.
On Initial self-test of the unit has passed and
is ready.
Internet
Green
Off
The device is under the Bridge mode,
DSL connection is not present, or the
power is off.
Blinks
Internet data is being transmitted in the
routing mode.
On
IP is connected.
Red On
The device is attempted to become IP
connected, but failed.
Rear Panel
Figure 2 Rear panel
3

DSL-2730E User Manual
The following table describes the interface of the device.
Interface/Button
Description
Antenna position
DSL RJ-11 interface that connects to the telephone set through
the telephone cable.
LAN4/3/2/1 Ethernet RJ-45 interfaces that connect to the Ethernet
interfaces of computers or Ethernet devices.
WPS Press the button for 1 second to enable WPS function.
WIRELESS
ON/OFF
Press the button silently to enable WLAN function.
ON/OFF Power on or off the device.
12V DCIN
Interface that connects to the power adapter. The power
adapter output is: 12V DC, 500mA.
Reset (on the
bottom case)
Reset to the factory defaults. To restore factory defaults,
keep the device powered on and push a paper clip into the
hole. Press down the button for 1 second and then release.
1.4 System Requirements
A 10 baseT/100BaseT Ethernet card installed on your PC
A hub or switch (attached to several PCs through one of Ethernet
interfaces on the device)
Operating system: Windows Vista, Windows 7, Windows 98SE, Windows
2000, Windows ME or Windows XP
Internet Explorer V5.0 or higher, Netscape V4.0 or higher, or Firefox 1.5 or
higher
1.5 Features
Various line modes
External PPPoE dial-up access
Internal PPPoE and PPPoA dial-up access
Leased line mode
1483B, 1483R, and MER access
4

DSL-2730E User Manual
Multiple PVCs (eight at most) and these PVCs can be isolated from each
other
A single PVC with multiple sessions
Multiple PVCs with multiple sessions
Binding of ports with PVCs
802.1Q and 802.1P protocol
DHCP server
NAT and NAPT
Static route
Firmware upgrade: Web, TFTP, FTP
Reset to the factory defaults
DNS relay
Virtual server
DMZ
Two-level passwords and user names
Web user interface
Telnet CLI
System status display
PPP session PAP and CHAP
IP filter
IP QoS
Remote access control
Line connection status test
Remote management (telnet and HTTP)
Backup and restoration of configuration file
Ethernet interface supports crossover detection, auto-correction and
polarity correction
UPnP
IPV6
5

DSL-2730E User Manual
2 Hardware Installation
Step 1 Connect the DSL port of the device and the Modem port of the splitter
with a telephone cable. Connect the phone to the Phone port of the
splitter through a telephone cable. Connect the incoming line to the
Line port of the splitter.
The splitter has three ports:
Line: Connect to a wall phone port (RJ-11 jack).
Modem: Connect to the DSL port of the device.
Phone: Connect to a telephone set.
Step 2 Connect a LAN port of the device to the network card of the PC
through an Ethernet cable (MDI/MDIX).
Note:
Use twisted-pair cables to connect the device to a Hub or switch.
Step 3 Plug one end of the power adapter to the wall outlet and the other end
to the Power port of the device.
Figure 3 displays the application diagram for the connection of the device, PC,
splitter and telephone sets, when no telephone set is placed before the splitter.
Figure 3 Connection diagram
6

DSL-2730E User Manual
3 Web Configuration
This chapter describes how to configure the device by using the Web-based
configuration utility.
3.1 Accessing the Device
The following is the detailed description of accesing the device for the first time.
Step 1 Open the Internet Explorer (IE) browser and enter http://192.168.1.1.
Step 2 The Login page shown in the following figure appears. Enter the user
name and password. The user name and password of the super user
are admin and admin.
If you log in as the super user successfully, the page shown in the following figure
appears. This page displays a summary overview of the router, including the
system information, DSL information, LAN Configuration, DNS information and
WAN Configuration.
7

DSL-2730E User Manual
8

DSL-2730E User Manual
3.2 Setup
In the main interface, click Setup tab to enter the Setup menu as shown in the
following figure. The submenus are Wizard, Local Network,Internet Setup,
Wireless Setup and Time and Date.
3.2.1 Wizard
Wizard enables fast and accurate configuration of Internet connection and other
important parameters. The following sections describe configuration parameters.
When subscribing to a broadband service, you should be aware of the method,
by which you are connected to the Internet. Your physical WAN device can be
Ethernet, DSL, or both.
Technical information about the properties of your Internet connection is provided
by your Internet service provider (ISP). For example, your ISP should inform you
that you are connected to the Internet using a static or dynamic IP address, and
the protocol you use to communicate over the Internet, i.g. PPPoA or PPPoE.
Choose Setup > Wizard. The page shown in the following figure appears.
Click Setup Wizard. The page shown in the following figure appears.
9

DSL-2730E User Manual
There are 5 steps to configure the device. Click Next to continue.
Step 1 Change the device login password.
Step 2 Set the time and date.
Step 3 Configure the Internet connection.
10

DSL-2730E User Manual
If the internet service you subscribed is PPPoE or PPPoA,you can choose the
Protocol to be PPPoE or PPPoA. Set the VPI and VCI. Enter the user name and
password provided by your ISP.
11

DSL-2730E User Manual
If the internet service you subscribed is Dynamic IP, you can choose Protocol to
be Dynamic IP. The page shown in the following figure appears.
If the Protocol is Static IP, you can choose Protocol to be Static IP. The page
shown in the following figure appears. Enter the IP Address, Subnet Mask,
Default Gateway and Primary DNS Server provided by your ISP.
12

DSL-2730E User Manual
If the Protocol is Bridge, the page shown in the following figure appears.
13

DSL-2730E User Manual
Step 4 Configure the wireless network.
Step 5 Complete and apply the settings. Click Apply to save the settings.
14

DSL-2730E User Manual
Note:
In each step of the Wizard page, you can click Back to review or modify the
previous settings. Click Cancel to exit the wizard page.
3.2.2 Local Network
You can configure the LAN IP address according to the actual application. The
preset IP address is 192.168.1.1. You can use the default settings and DHCP
service to manage the IP settings for the private network. The IP address of the
device is the base address used for DHCP. To use the device for DHCP on your
LAN, the IP address pool used for DHCP must be compatible with the IP address
of the device. The IP address available in the DHCP IP address pool changes
automatically if you change the IP address of the device.
You can also enable the secondary LAN IP address. The two LAN IP addresses
must be in different networks.
15

DSL-2730E User Manual
3.2.2.1 LAN Interface
Choose Setup > Local Network > LAN Interface. The LAN Setting page
shown in the following figure appears. You may configure the LAN interface, for
example, the IP address and subnet mask.
16

DSL-2730E User Manual
The following table describes the parameters in this page.
Field Description
IP
Address
Enter the IP address of LAN interface. It is recommended to
use an address from a block reserved for private use. This
address block is 192.168.1.1- 192.168.1.254.
Subnet
Mask
Enter the subnet mask of LAN interface. The range of subnet
mask is from 255.255.0.0-255.255.255.254.
Secondary
IP
Select it to enable the secondary LAN IP address. The two LAN
IP addresses must be in different subnets.
LAN Port
You may choose the LAN interface you want to configure.
Link
Speed/
Duplex
Mode
You may select one mode from the drop-downlist:
100Mbps/FullDuplex, 100Mbps/Half Duplex,
10Mbps/FullDuplex, 10Mbps/Half Duplex and Auto
Negotiation.
MAC
Address
Control
It is the access control based on MAC address. Select it, and
the host whose MAC address is listed in the Current Allowed
MAC Address Table can access the modem.
Add Enter MAC address, and then click this button to add a new
MAC address.
3.2.2.2 LAN IPv6 Interface
Choose Setup > Local Network > LAN IPv6 Interface. The LAN IPv6 Setting
page shown in the following figure appears. You may set LAN RA server work
mode and LAN DHCPv6 server work mode.
17