D-Link Express EtherNetwork DI-604 User manual

Before You Begin
1. If you purchased this router to share your high-speed Internet connection with
other computers, you must have either an Ethernet-based Cable or a DSL modem
with an established Internet account from an Internet Service Provider (ISP).
2. It’s best to use the same computer that is connected to your modem for
configuring the DI-604 router. The DI-604 Router acts as a DHCP server and will
assign all the necessary IP address information on your network. See Appendix
at the end of this Quick Installation Guide or the Manual on the CD-ROM for
setting each network adapter to automatically obtain an IP address.
Check Your Package Contents
These are the items included with your DI-604 purchase:
If any of the above items are missing, please contact your reseller.
©2003 D-Link Systems, Inc. All rights reserved. Trademarks or registered trademarks are the property of their respective
holders. Software and specifications subject to change without notice. DI-604.03072003
This product can be set up using any current
web browser, i.e., Internet Explorer 5x,
Netscape Navigator 4x.
DI-604
Express EtherNetwork™
Broadband Router
• DI-604 Ethernet Broadband Router
• CD-ROM (containing Manual and Warranty)
• Ethernet (CAT5 UTP/Straight-Through) Cable
• 5V DC, 2A Power Adapter
Using a powe
r
supply with a
different voltage rating
will damage and void
the warranty for this
product.

Connecting The DI-604 Broadband Router
To Your Network
A. First, connect the power adapter to the receptor at the back panel of the
DI-604 and then plug the other end of the power adapter to a wall outlet or
power strip. The Power LED will turn ON to indicate proper operation.
B. 1. Power off your Cable or DSL modem; some devices may not have a on/off
switch and will require you to unplug the power adapter. Now, the DI-604
should be powered on and the Cable / DSL modem should be turned off.
2. Cable / DSL modem (Power Off) – DI-604 (Power On)
Connect an Ethernet cable to the Ethernet jack located on the Cable / DSL
modem. After the Ethernet cable is securely connected, power on the Cable /
DSL modem by turning on the unit or plugging in the power adapter.
3. Cable / DSL modem (Power On) – DI-604 (Power On)
Insert the other end of the Ethernet cable to the WAN PORT on the back
panel of the DI-604. The WAN LED light will illuminate to indicate proper
connection. If the WAN LED is not illuminated, please go back and step B and
repeat its instructions.
C. Insert an Ethernet cable to LAN port 1 on the back panel of the DI-604 and an
available Ethernet port on the network adapter in the computer you will use to
configure the DI-604. The LED light for LAN Port 1 will illuminate to indicate
proper connection. (Note: The LAN Ports on the DI-604 are Auto-MDI/MDIX.
Meaning you can use a straight-through or crossover-Ethernet cable to the
LAN Ports.)
B.WAN Port
This is the connection for the
Ethernet Cable to Ethernet Port on
the Cable or DSL Modem.
C.LAN Ports
These are the connections for Ethernet
cables to your Ethernet-enabled computers
Reset Button
Pressing this button
restores the router
to its original factory
default settings.
A.Receptor for
Power Ada
p
te
r

Connecting Additional Computers To The
DI-604 Broadband Router
Using additional Ethernet (CAT5 UTP/Straight-Through) cables, connect
your Ethernet-equipped computer(s) to one of the 3 remaining Ethernet
LAN ports on the back panel of the DI-604.
When you have completed the steps in this Quick Installation Guide, your
connected network should look similar to this:
Cable or DSL
Modem
DI-604 Ethernet
Broadband Router
Computers connected
to the LAN Ports
LAN Port LEDs. Each of the
LAN ports on the back of the
DI-604 have a corresponding
LED light on the front panel
of the unit. When a proper
connection has been made
to a computer that is ON, the
LED on the front panel
should illuminate.

Using The Setup Wizard
The logon pop-up
screen will appear.
Once you have
logged in, the
Home screen
will appear.
Open your Web
browser and type
“http://192.168.0.1” into
the URL address box.
Then press the Enter or
Return key.
Type “admin” for the
username and leave the
password field blank.
Click OK
Click Run Wizard

You will see the following screens.
Step 1 - Set up your new
password.You have the option to
establish a password.
Step 2 - Choose your time zone.
Click Next
Click Next
Click Next

The Setup Wizard (continued)
Select the type of Internet connection for your router.
If you selected Dynamic IP
Address, this screen will
appear:
Select one of
these settings
If you are unsure of which setting to
select, please contact your Internet
Service Provider.
Click the “Clone MAC
Address” button to
automatically copy the MAC
address of the network adapter
in your computer. You can also
manually type in the MAC
address. What is a MAC address? Each
network adapter has a discrete
Media Access Control (MAC)
address. Note that some computers
and peripherals may already include
built-in network adapters.
Click Next
Click Next

If your ISP requires a Static IP
Address, and this option is
selected, then this screen will
appear:
If your ISP uses PPPoE (Point-to-
Point Protocol over Ethernet) and
this option is selected, then this
screen will appear:
Enter in the username
and password provided
to you by your ISP.
Do not use
the numbers
displayed in these
fields. They are only
shown as an example.
Click Next
Enter the IP address
information originally
provided to you by your ISP.
You will need to complete all
the required fields.
Click Next
Please be sure
t to remove any
existing PPPoE
client software
installed on your
com
p
uters.

Your Setup is Complete!
You will be returned to the Home tab.
Click Restart
Click Close

Test Your Internet Connection
Relaunch your Web
browser (i.e., Internet
Explorer or Netscape
Navigator), to link to
your favorite Web site
to test your Internet
connection.
For additional settings
or information, refer to
the Advanced, Tools,
or Status tabs on the
web-management
interface; or to the
manual located on the
CD-ROM.
Click Exit

APPENDIX
To connect to the network, make sure
the network adapter in your computer
is configured properly. Here’s how to
configure the network adapter to obtain
an IP address automatically for the
DI-604 Broadband Router.
For Microsoft Windows XP:
Go to Start > right click on
My Network Places >
select Properties > Double-click on
the Network Connection associated
with the Ethernet adapter (i.e.,
D-Link DFE-530TX+).
Click Internet Protocol (TCP/IP)
Click Properties
Select Obtain an IP address
automatically
Click OK
Restart your
computer