Daan Tech Bob User manual

Q  

1
EN
Table of content
1 | QUICK SET-UP GUIDE 2
1 | Scope of application and place of use 2
1.1 | Scope of application 2
1.2 | Place of use 2
2 | Set-up and Connections 3
2.1 | Water inlet 3
2.2 | Water outlet 3
2.3 | Power plug 4
3 | Getting started 5
4 | Capacitive door opening 5
5 | Configure your basket 6
2 | QUICK UTILIZATION GUIDE 7
1 | Interface 7
1.1 | Navigate through Bob interface 7
1.2 | Menu options of the home screen 8
2 | Basket Set-up 8
2.1 | Maximum size of plates 8
2.2 | Recommendations on how to place kitchenware inside Bob 9
2.3 | Basket configuration according to your needs 10
3 | Wash cycle 12
3.1 | How a wash cycle works 12
3.2 | Standard programs 14
4 | Detergent for Bob 15
3 | QUICK MAINTENANCE GUIDE 16
Product description 16
1 | Filters 16
2 | Heating Elements 18
3 | Cover and screen 18
4 | Spray arm 19
4 | QUICK TROUBLESHOOTING GUIDE 20
1 | List of possible issues 20
2 | Repair and customer service 24
Product sheet 24
Safety instructions
yBob, the mini dishwasher, is intended to be used as a domestic home appliance and
for similar purposes, including: professional environments such as kitchenettes used by
personnel at the office and for use in any residential room, including hotels and motels.
PLEASE READ THE SAFETY INSTRUCTIONS CAREFULLY BEFORE USING BOB - THE MINI
DISHWASHER - AND KEEP THEM FOR FUTURE REFERENCE.
yBob can be used from the age of 8 years as well as by people with physical or mental disabilities
as long as a proper supervision is guaranteed or if the former has been provided with the
following safety guidelines and is aware of the possible risks involved with the usage of Bob.
Children shall not play with Bob. Cleaning and maintenance of the appliance shall not be carried
out by unsupervised children.
yIf the power cable is damaged, it shall be replaced either by the manufacturer, its after sales
service or by any similarly qualified person in order to avoid hazard occuring.
yTo inform yourself how and when to clean the appliance, please refer to the Quick maintenace
guide.
yThe door shall not remain fully open to avoid potential incidents, yet it is highly recommended
to slightly leave it open guaranteeing air circulation and thereby decreasing standby energy
consumption.
yWARNING: Knives and other cutlery must be put in the cutlery basket module with its blades
and pikes pointing downwards.
yOnly the new tubes and power cable provided with Bob shall be used while used ones should
not be used.
yInformation on how to load the basket is provided within the section Basket configuration
according to your needs.
yThe pressure within the water inlet shall be between 0,05 Mpa and 1 Mpa.
yThe power plug shall be easily accessible after Bob’s set-up.
yAccording to standard EN50242, this dishwasher shall not be used to clean more than two
place-settings.
IMPORTANT SAFETY GUIDELINES:
yBob, the mini dishwasher, shall only be used to clean plates, glasses, forks, and knives.
yNever unplug Bob from the power network by pulling the power cable, always pull the power
plug instead.
yBefore plugging Bob to the power network, please check if the tension recommended on the
type plate matches the one of the power network. Bob has to be placed on a stable and/or even
surface. Daan Tech is not liable for damage resulting from the use of Bob on an uneven and/or
unstable surface.
yDo not touch Bob when your hands or feet are wet.
yNever open the door during a wash cycle. You may on Bob's door, open carefully and be exposed
to steam or hot water. To pause an ongoing program, please press and wait for 3 seconds.
yDo not let children climb on Bob’s door and do not place heavy objects on the door while it is
open. It may result in the dishwasher tipping over.
yDo not put living creatures, animals or pets inside Bob! ;)

2 available options
2 | Set-up and ConneCtionS
2.1 | Water inlet
Plug the water inlet hose
on one side to the back of Bob and on the other
side to a water inlet via a 19 mm threaded end
(3/4 inch) and make sure the connection is
firmly tightened.
WARNING: Close the water supply tap
after each use of Bob.
Using Bob as an autonomous free-standing
dishwasher thanks to its built-in water tank. In
this case, no water inlet hose is needed! Please
use carafe to quickly fill the water tank! Bob can
be filled with either cold or hot water up to 60°C.
Please always fill the water tank before use (4L
capacity) with the door open, until you hear the
signal sound that indicates that the tank is full.
12
Do not overfill the tank! If you fill in
more than the water tank capacity (4 L),
the excess water will escape into Bob’s
main interior.
Warning: Do not block the water inlet of
the water tank. This must always remain
free.
2.2 | Water outlet
Plug the water drain hose to the back of Bob.
Warning: To prevent leaks, please use a screwdriver to fix the
water outlet.
1.2 | Place of use
3 options
O    
The shelf should withstand a weight of 25kg (55,1 lbs) (weight of Bob + water + dishes).
You can place Bob anywhere you want, it is the smallest dishwasher ever!
1 | SCope of appliCation and plaCe of uSe
1.1 | Scope of application
Bob’s 4 feet can be adjusted up to
+1cm (+0,4in) to ensure that it is in
a perfectly horizontal position.
Warning: Bob’s inclination shall not exceed 2° in order to avoid possible flooding.
Precautions against frost:
Bob shall not be stored in a place with a temperature lower than 0°C. If such a situation could
occur, ensure that Bob has been drained using the draining program ( )and remove the
inlet water hose.
Bob might be humid inside when you receive it. In fact, every Bob has been tested before shipping
(empty cycle with clear water). Therefore, there might still be some traces of residual water.
19,3 in
19,3 in
13,4 in
32
EN
1 | QuiCK Set-up Guide
O   
B  
The provided water outlet’s length is 1m50.
During a cycle, please make sure that nothing hinders the automatic opening of the door at
the completion of the program.
Warning : In the long run, the steam released during the opening of the door may damage
wooden surfaces.
Place Bob on a water-resistant surface to avoid stains. When filling Bob’s water tank or taking
out dishes, drops of water may end up on the work surface.

3 | GettinG Started
2 O     :
Use the water inlet pipe. The water tank is automatically filled before each cycle,
so there is no need to fill it manually. It is the preferred choice if you use Bob as a built-
in dishwasher or if you have close access to a water supply.
Use the built-in water tank: convenient, because it makes Bob completely
autonomous to use wherever you are. Fill the built-in water tank with Carafe. This is
the preferred choice if you intend to regularly move Bob around or if you do not have
access to a water inlet.
4 | CapaCitive door openinG
When you touch the door, it automatically opens.
Convenient, because you can open the door
of your Bob with your elbow, for instance, if
your hands are dirty!
The capacitive area is here
To avoid problems, the capacitive door opening is
deactivated for 3 seconds after closing the door.
When Bob is disconnected from the power supply
you can still open the door but you will encounter
greater resistance due to the deactivation of the
door’s capacitive opening system.
2.3 | Power plug
WARNING: Please turn the power supply off before installing Bob.
Connect the power cable to Bob’s back.
Before you connect Bob to the power supply, please make sure that the voltage on the
type plate corresponds to the voltage of your power supply.
The appliance must be placed on an even and stable surface. Daan Tech is not liable for
any damage caused by placing the device on an uneven and/or unstable surface during use.
Do not plug or unplug by pulling the cord, but always
pull the plug directly.
Connect the water outlet hose to a siphon drain pipe (usually accessible
under the sink)
Warning: The waste water coming out of Bob can reach high
temperature of up to 70°C.
1Siphon drain pipe
2 options for evacutaing the waste water
2
Place the drain hose directly
in your sink and fix it with
the equipment provided.
Place the drain hose in a
container (jerrican, bucket,
etc...)
To avoid possible flooding, the container shall have a capacity of at least 5L.
Fixed installation
Flexible installation
Install the water outlet drain hose either in a fixed or flexible mode by using the
equipment provided.
54
EN

EXPRESS DAILY INTENSIVE ECO TIMER
Bob has an analog display (black & white) only in English and 3 buttons.
1 | interfaCe
1.1 | Navigate through Bob interface
ySwitch left
yStart Bob
yStart a program
yPause a program
yValidate
ySwitch right
Left button
Right button
Central button
Cycles icons and names
Cycle duration
2 | QuiCK utiliZation Guide
Warning
Drying icon
At the end the door opens for drying
5 | ConfiGure your baSKet
Bob adapts to multiple types of dishes thanks to its modular design and
can thus be used all sorts of occasions.
Module for 6 plates
2 modules for 4 glasses Module for cutlery
Basket
The basket allows you to place the module in many different ways.
You can place the plate module
either in the middle of the
basket or at one of the two
sides.
Choose where you want to
place the cutlery module, or
remove it if you do not need it!
Place your forks and knives so that the closing of the door is not disturbed. In fact, sharp
elements can damage the seal and cause leaks.
76
EN

Some items shall not be cleaned using a dishwasher:
yKitchenware items that are made from stuck or welded parts and do not withstand heat.
yKitchenware items made of copper, tin, crystal, aluminium, zinc, or are likely to rust, wood,
synthetic fibres or which cannot withstand heat.
yKitchenware with handles made of wood, horn, porcelain or nacre.
Very often, items that can be cleaned with a dishwasher
have one of the following label on the packaging.
Knives and other kitchenware with long blades may cause hazard if they are not pointing
downwards. Thus, please make sure to load items in such a way that the blades pointing
to the bottom.
Warning: Never start a program without the main basket.
2 | baSKet Set-up
2.1 | Maximum size of plates
The dimensions of Bob’s interior are the following:
29 cm (11,4 in) height / 28 cm (11 in) width / 35 cm (13,8 in)depth
Even considering the small size, Bob fits many items of different dimensions and shapes.
A few examples of items fitting in Bob
Plates of a diameter up
to 29cm (11,4 in).
Platters, up to 35cm
(13,8 in) length x 28cm
(11in) width x 10cm (3,9
in) height
Baby bottles, carafes,
and more.
Pans or saucepans
Prefer using pans
and saucepans with
removable handles to
save space.
2.2 | Recommendations on how to place kitchenware inside
Bob
Before putting kitchenware inside Bob, please mind some recommendations:
Bob’s configurable basket matches all kinds of kitchenware.
1. Please remove food waste, as it might block the filter
or the spray arm.
2. Soak (sauce) pans with hot water if there are burnt
stains before placing them in the basket.
3. Please mind checking that your kitchenware (in
particular lightweight ones) such as plastic containers
are fixed so that they do not flip or impede the spray
arm while the program is running.
4. Please place objects, such as pans, cups and glasses
etc., in a way that they do not store liquid while the
cycle is running.
When starting Bob you may navigate through the different menu options
of the home screen.
1.2 | Menu options of the home screen
The following menu options are available.
You can navigate right and left by pressing and .
Express Intensive Eco
Timer
Daily Emptying
This cycle
allows you to
drain the water
tank.
Schedule your cycles
yGo to the Timer menu and confirm with
ySelect the cycle to postpone with and
yConfirm with
yChoose the shift time (3H-6H-9H-12H) with and
yConfirm with
yIf the tank is empty, fill it so that the timer starts (otherwise the cycle will be blocked
on the "No Water" screen and will not start)
yThroughout the wait, it is possible to cancel the deferral by pressing central button
98
EN

Basket configuration according to European standards:
CYCLE FOR 2 STANDRAD PLACE SETTINGS
y1 soup plate
y1 melamine bowl
y3 dessert plates
y1 Melamine dessert plate
y1 saucer
y1 dessert bowl
y1 cup
y2 glasses
y1 mug
y1 serving fork
y2 forks
y2 soup spoon
y2 knife
y2 dessert spoon
y2 tea spoon
y1 gravy ladler
Recommended cycle
ECO - 180 min - 3,8L of water
Degree of soiling
Soiled and dried up / eggs, oat, milk, tea,
margarine, spinach.
*EN 50242 : This program is the test cycle. The comparative information are in line with the EN 50242
norm. Leave the door open at the end of the cycle to reduce power consumption.
x1 Plate
module
x2 Glass
module
x1 Cutlery
module
2.3 | Basket configuration according to your needs
Depending on your dishes, adapt the modules to ensure easy handling and
guarantee optimal washing performance.
Here are a few examples of basket configurations using different modules, according to the time of
day:
DINNER WITH GUESTS
(4 people)
y4 big plates
y4 knives
y4 forks
y4 small spoons
y4 glasses
y4 cups
Recommended cycle
Intensive - 90 min - 3,8L of water
Degree of soiling
Soiled and dried up / gluten, plant fibres, alcohol, etc...
x1 Plate
module
x 2 Glass
modules
x1 Cutlery
module
1110
EN

DAILY
3 | WaSh CyCle
3.1 | How a wash cycle works
You can follow the progress of the current wash cycle on Bob’s screen
Icon of the current program
Remaining time
(minutes and seconds)
yMake sure that your dishes are positioned correctly in the basket
yPut detergent (gel or tablet or powder) inside the tank
yClose the door. Warning: the cycle cannot be initiated if the door is open or not properly closed
yChoose the most appropriate program according to your dishes and the degree of soiling
yStart the cycle on Bob’s display
yFill the water tank until the signal sound occurs if your Bob is not connected to a water
supply
Before starting a wash cycle
Warning: Ensure that the drain hose is correctly positioned at a water drain
or a container during the entire cycle. Water is drained several times during
a cycle.
Let’s go! The cycle is running now!
yPress the central button to pause the current cycle.
ySelect NO to cancel the current cycle and to launch a drain.
yYou will automatically be redirected to the home screen.
Cancelling an ongoing cycle
During a wash cycle
When the timer is close to zero, the “Drying in progress” icon is displayed.
At the end of the wash cycle
At this point, the door opens automatically and remains half-open with a 10
degree angle.
Warning Please note that hot steam is released when door opens
Depending on the program, drying might take several minutes and will not
consume additional energy. The program is not completed yet; please wait
a few minutes for the drying to finish before removing your dishes.
Warning Please note that some items are very hot and could cause
skin burns if removed too soon. Daan Tech shall not be responsible
for such incidents, which occur when dishes are removed before the
offical end of the cycle.
When the program is completed, a signal sound occurs and Bob will automatically go into standby
mode.
Upon completion of the program, leave Bob’s door open (10°) to prevent unpleasant smell. This also
reduces the energy consumption in the standby mode.
Please note that some water
residue may remain on your
dishes if you do not wait for the
drying to nish.
Adding extra items during an ongoing cycle
yPress the central button to pause the current cycle.
yOpen the door and pay attention to the escaping hot steam
yPlace the additional item in the basket
yClose the door
ySelect YES to continue the cycle
Warning: If you want to cancel a cycle or add additional items, you must press the central
button to interrupt the program.
1312
EN

yPlace the tablet in the slot provided
yRun a cycle of 50 minutes or more to ensure the best wash quality
(higher efficiency from 45°C)
You can use powder or gel or tablets.
Tablettes
Gel ou poudre
If you are using gel or powder, you can put 5g in the notch at the bottom of
the door when it is open.
4 | deterGent for bob
Please only use dishwasher detergents. Using other detergents, such as
hand soap may damage the product and end the warranty. Please note
that dishwasher detergent are corrosive and dangerous. Keep them out
of reach of children.
D  
E
C    (T°C)
C 
D ()*
W  (L)
E  (W)
*(Drying time not included)
20 min
2.9 L
**
Slightly soiled
but no dried-in
stains.
Breakfast
Washing at
70°C
Rinsing
Hot rinisng at
65°C
Drying at 65°C
0,26 kWh
Express
91 min
3.8 L
*****
Soiled and
dried-in and
possibly burnt-
in stains.
(Sauce)pans,
dishes and
cutlery
Pre-washing at
68°C
Washing at 40°C
Cold rinsing
Hot rinsing at
65°C
Drying at 70°C
0,48 kWh
Intensive
180 min
3.8 L
****
Soiled and
dried-in but
not burnt-in
stains.
Lunch or
dinner
Pre-Washing at
50°C
Washing at 40°C
Cold rinsing
Hot rinsing at
65°C
Drying at 65°C
0,43 kWh
Eco
50 min
3.8 L
***
Soiled but not
dried-in or
burnt-in stains.
Lunch or
dinner
Pre-washing at
65°C
Washing at 40°C
Rinsing
Hot rinsing at
65°C
Drying at 65°C
0,35 kWh
Daily
3.2 | Standard programs
Bob offers various programs dedicated to: specific occasions, different dishes and different
degrees of soiling. Please consult the following overview to find out which program is the best fit
for your needs.
1514
EN

Once a week or every 10 cycles
Turn the microfilter counter-clockwise to unlock the microfilter/
coarse filter combination.
Warning: Never start a cycle without the filters in place.
If your microfilter is damaged, please contact your seller's after-
sales service..
Additionally, lift out the stainless steel filter.
Rinse the 3 filters under running tap water and clean them with a
soft bristle brush
Now reinsert the micro filter/coarse waste filter combination by
turning it clockwise until it clicks to ensure its correct position.
Put the stainless steel filter back into Bob.
Filter maintenance
Remove the coarse waste filter with one hand using
its two grip tabs.
Dispose the waste in the bin, clean the coarse waste filter
with clear water and put it back in place.
After each cycle
Maintenance calendar
Tasks Timing Tools
Filters
After each cycle Water
Once a week or every 10 cycles Water
Soft bristle brush
Heating elements Once per month or every 30
cycles
Non abrasive sponge and
degreasing product
Plastic shell, screen and
button
Depending on the amount of soil
on Bob. Moist wipe
Always unplug the appliance before cleaning.
1 | filterS
Bob’s filter system, designed by Daan Tech, consists of 3 filtration stages
A. Stainless-steel filter: First filtration of soil and food particles through a perforated stainless
steel mesh. This first filtration stage allows the water to pass through, while redirecting the soil to
the second filtration stage.
B. Filter for coarse waste: Second filtration and recovery of coarse waste. Large lumps of food are
collected in this coarse waste filter.
C. Micro-filter: Third filtration stage and filtration of fine particles thanks to a 120 micron
microfilter.
C. Micro-lter
B. Coarse waste lter
A. Stainless-steel lter
produCt deSCription
Bob is designed to last at least 10 as long as it is regularly and rigorously maintained.
To ensure a long life for Bob, please follow the recommendations found in this maintenance
guide.
3 | QuiCK MaintenanCe Guide
1716
EN

3 | Cover and SCreen
To clean the exterior of Bob, simply wipe it with a damp cloth
Depending on the amount of soil on your Bob.
Please do not use any scouring agents, chemical solvents or strong detergents as this
could damage the coating of Bob.
To prevent water from getting into the electronic components, screen, buttons or door lock
system,do not use a cleaning spray.
2 | heatinG eleMentS
The heating disk must be cleaned thoroughly to avoid clogging and
reduced rinsing performance.
Once per month or every 30 cycles
To access the heating disc, please remove the 3 filters.
Then remove the protection part of the heating disc and clean it.
You then have access to the heating disc, clean it with a non-
abrasive sponge in order to avoid damaging (scratching) the non-
stick coating.
Put the protection part back in place.
Then reinsert the 3 filters.
4 | Spray arM
If you encounter problems with the spray arm and have observed that it no longer turns, it may
be a nozzle blockage that prevents it from turning. In this case, please follow the instructions
below to clean the spray arm.
To remove the spray arm, unscrew the ring at base of the
spray arm with one hand.
Wash the spray arm under running water and remove any food
residues from the spray nozzles.
Put it back in place and make sure that nothing hinders its
rotation.
1918
EN

1 | liSt of poSSible iSSueS
4 | QuiCK troubleShootinG
Guide
Issue Possible causes Known solutions
Bob does not turn on.
A fuse has blown in your
electrical system or the circuit
breaker has tripped.
Unplug all other appliances
connected to the same electrical
circuit as Bob. Replace the fuse or
reset the circuit breaker.
The power supply is not
activated.
Check that the power cord is properly
plugged at both ends into either the
wall outlet or at Bob’s side.
The cycle does not start.
The door is open. Close the door.
The door remains open,
impossible to close it.
Check whether something is
blocking the closing of the door. If
it is not the case, please contact the
After Sales Service.
No water or not enough water
in the tank.
If you are in the “integrated tank”
mode: fill the tank up until the signal
sounds.
If you are in the “water supply” mode:
check your installation (tap open,
sufficient pressure).
The screen is frozen and the
buttons no longer respond.
Wait 3 seconds until Bob has started.
If the screen is still frozen, disconnect
and reconnect Bob.
Water does not drain out
of Bob.
The drain hose is bent. Check the drain hose and fix it with
“Bob Easyfix”.
The water outlet is blocked
(under the filter).
Clean the bottom of the interior and
the filters.
The drain hose is blocked by a
foreign body/material.
Contact your seller's after-sales
service..
Issue Possible causes Known solutions
Formation of foam inside
the tank during a cycle.
Inappropriate detergent.
Only avoid special dishwasher
detergent to avoid foaming. However,
if this happens, open the dishwasher
door and
allow the foam to evaporate.
Close the door and start a wash
program to drain the water. Repeat
the procedures if necessary. Reduce
the amount of product in the next
cycle.
Soil that generates foam.
Different types of soil generate more
or less foam. However, if there is too
much foam during a cycle it can
block the spray arm. In this case,
empty the basket and run an empty
cycle before you start washing your
dishes again.
Stains on interior
surfaces.
Limescale may appear on the
surfaces.
Pour 10cl of white vinegar into Bob's
tank and run an intensive cycle.
The dishes are not clean.
The dishes are not placed
correctly in the basket.
Avoid any contact between the
different items in the basket. Please
refer to: Recommendations for the
arrangement of the dishes in the
basket.
The selected wash program is
unsuitable.
Choose a more intensive program.
Refer to: Standard programs
The spray arm is blocked by
dishes.
Change the arrangement of the
dishes so that the spray arm can
rotate freely.
One or more of the spray arm
nozzles is/are clogged.
Disassemble and clean the spray
arm.
The filter are not clean or are not
correctly arranged. Disassemble and clean the filters.
2120
EN

Issue Possible causes Known solutions
The dishes do not
properly dry.
The dishes are incorrectly
arranged within the basket
Refer to: Recommendation for the
arrangement of the dishes in the
basket.
The selected program is not
suitable.
Choose a program with a longer
washing time.
The door did not open at the
end of the cycle.
Check that nothing prevents the
door from opening automatically at
the end of the cycle.
The dishes did not have
sufficient time to dry.
Wait for the signal tone at the end
of the cycle before taking out your
dishes.
Emergence of water
under Bob
The tank floods.
The tank capacity is 4 litres.
If you are in the “integrated-tank”
mode, do not overfill it.
If you are in the “water supply” mode:
switch your water supply off and call
your seller's after-sales service.
The door leaks.
Check the condition and position of
the seals on the door and whether
something prevents the door from
closing completely.
Leak at the drain hose
connection.
Use the supplied clamp and the
screwdriver to tighten the drain hose
on the back of Bob.
Leak at Bob’s easywater
connection. . Check the connection and tighten it.
Leak in the tank Contact your seller's after-sales
service.
My dishes are damaged. Unsuitable cycle. Do not put any fragile cutlery in Bob
Damp packaging
Every Bob is tested in the factory
before delivery, which is why
water residues may be present.
(N/A)
The inside of Bob is
humid.
Every Bob is tested in the factory
before delivery, which is why
water residues may be present.
Issue Possible causes Known solutions
Bob is not responsive
(the screen is frozen, the
buttons no longer react)
Malfunctioning Restart Bob by unplugging and then
plugging it in again.
Bad smell (inside the
tank)
Bob has not been used for a
long time.
Drain your Bob completely
with the emptying cycle (Emptying
menu ), then start an empty cycle.
Leave the door open at a 10° angle, if
Bob is not in use.
Pour 10cl of white vinegar into Bob's
tank and run an intensive cycle.
2322
EN

Brand name Bob
Product name BOEM
Manufacturer name Daan Technologies SAS
Origin of manufacturing France (Vendée)
Number of standard place settings 2
Energy efficiency class G
Annual energy consumption 98 kWh/year
Energy consumption for a standard cycle 0,40 kWh/cycle
Standby power consumption (door half-open) 0.5 W
Standby mode duration 5 minutes
Annual water consumption 1064 litres
produCt Sheet
This product sheet complies with the European Directive No. 1059/2010.
NOTES
A (maximum efficiency) to G (minimum efficiency)
Energy consumption of 98 kWh based on 280 standard wash cycles with cold water supply and consumption of low power
modes. The actual energy consumption may differ depending on the conditions.
Water consumption of 1064 litres a year based on 280 standard wash cycles. The actual energy consumption may differ
depending on the conditions.
A (maximum efficiency) to G (minimum efficiency)
This program is suitable for cleaning medium solid dishes. It is the most efficient program in terms of the combined
energy and water consumption for this type of dishwasher.
DISPOSAL
As a manufacturer, we commit to reduce the environmental footprint of our products. We highly recommend you to follow
the disposal guidelines applicable in your country. This will help preserving natural resources by recycling Bob in an eco-
friendly manner. Since Bob has built-in electronic parts, it shall not be disposed with household waste, and must be discarded
according to the applicable law at the time of disposal. For more information about the disposal of electronic waste, please
ask your local authorities.
Drying performance class A
Standard cleaning cycle Eco
Duration of the standard cleaning program 180 minutes
Sound level 43 dB(A) re 1 pW
Can be used as built-in dishwasher No
Height 49 cm (19,3 in)
Width 34 cm (13,4 in)
Depth (with cables & water inlet / outlet) 49 cm (19,3 in)
Power consumption 1000 W
Voltage & Frequency 220-240V~ 50Hz
Water pressure (water inlet) 0,5-10 bar = 0,05-1 MPa
2 | repair and CuStoMer ServiCe
All components are available for 11 years from the date of purchase of the Bob. If you have a
problem with a component of your Bob, please contact the customer service department of the
shop where your Bob was purchased.
IMPORTANT: If you need to have your Bob repaired or transported, please follow the return
procedure:
1. Drain your Bob with the Drain cycle (Drain menu ) and/or unplug the Bob and turn it over a
sink to empty the remaining water in the tank
2. Clean the filters, the spray arm with clean water and the inside of the tank with a sponge
3. Seal the water inlet and outlet with absorbent paper before sending.
4. Be careful not to wrap Bob in plastic, as the electronics may be damaged by water.
5. Place Bob in his original box with the protections provided.
6. Tape the top and bottom cardboard flaps well.
2524
EN