Daesung Celtic SHW-13 User manual

SHW-13 SHW-20 SHW-26
SHW-30 SHW-33
THIS HOT WATER UNIT IS NOT FOR POOL OR SPA HEATING
INSTALLATION REQUIREMENTS.
This unit must be installed in accordance
1.These instructions.
2.Uniform Building Regulations Local authority regulaions;
3.AS/NZS 3500.4 National Plumbing and Drainage Code.Part4 Hot Supply Systems.
4.The installation code AS/NZ5601.1 for gas burning appliances and equipment.
5. Any other statutory regulation that may apply.
6. A notice of intention to install shell be lodged with the recelant Municipal Authority and local
Gas Authority prior to installation.
7. This appliance is not intended for use by persons(including children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge, unless they have been given supersision or
instruction concerning use of the appliance by a person responsible for their safety.
INSTALLATION MUST BE CARRIED OUT ONLY BY AN AUTHORISED AND APPROPRIATE
LICENSED PERSON
Please Note:
This is a modified
Manual.
Pages 22 - 26, 56
& 58 have been
removed as they
refer only to the
smaller units.

User’s Guide ----------------------------3
Important Safety Information -------3
General Parts ---------------------------8
Main Unit --------------------------------8
Remote Controller ------------------10
Initial Operation ----------------------11
Setting and Using the water heater-12
Freeze protection --------------------13
Regular Maintenance ---------------14
Troubleshooting ----------------------16
Specifications -------------------------21
Isometric -------------------------------22
Installation Manual ------------------32
1. Included Accessories -----------33
2. Optional Accessories -----------33
3. Before Installation ---------------34
4. Choosing Installation ------------35
5. Installation Clearances ----------37
6. Unit Installation -------------------38
7. Venting ------------------------------39
8. Gas supply and gas piping ----47
9. Water Piping ----------------------47
10. Application Diagrams ----------50
11. Electrical Wiring -----------------51
12. Condensate Drain --------------53
13. Maintenance ---------------------54
14. Trial Operation ------------------55
15. Dimensions ----------------------56
Servicing Manual ---------------------61
1. Servicing schedule ---------------61
2. Water heater front case removal
& Replacement of components -62
3. Draining the water heater ------63
4. Cleaning the combustion chamber -63
5. Burner -------------------------------64
6. Spark plug & Flames sensing rod -64
7. Igintor --------------------------------65
8. Thermostat -------------------------65
9. Flow Rate Control Valve --------66
10. Bypass Control Valve ----------66
11. Fan ---------------------------------67
12. Overheat thermostat -----------67
13. Latent Heat Exchanger --------68
14. Sensible Heat Exchanger -----68
Measurement -------------------------69
1. Inlet Gas Pressure ---------------69
2. Manifolder Gas Pressure -------69
16. Multi Remote Controllers -----60

Supplier
outdoor,

30cm
5cm 5cm
60cm
30cm
Ground:

1km.
Supplier
13
35
13

External Main Unit (SHW-13 ~ 33)
Outdoor
57~58
Air Intake
[SHW-13~26 Model]
[SHW-30~33 Model]

Indoor
59~60
[SHW-30~33 Model]
[SHW-13~26 Model]
Internal Main Unit (SHW-13 ~ 33)

40
It indiates Priority mode
is turned on.
for your safety.
Priority mode is used only when a secondary remote is installed.

Priority Operation
If the priority light is off, then press the Priority button on
the temperature controller to use priority function.
The Green priority light will glow indicating that this cont-
roller can controll the temperature and also the water he-
ater is ready to supply hot water.
If the controller is lighting on ‘Priority’, the others do not
change the temperature and priority light is flickering.
Open

40
37~50℃, 55℃, 60℃, 65℃, 70℃)
37~50DegC (in 1 increments)℃
50 , Hold UP℃
45℃
50℃
50℃
Hold it
down
for 5sec.
button down for

external pipes from
freezing.
Electrical heating elements are used for freeze protection.
11

[External Model]
[Internal Model]

1.1 liters
Place a bucket under the unit and drain water from it.
for water leak.
(Be careful not to lose the O Ring seal)
to relieve pressure.

2.5LPM
2.5lpm
240V / 50Hz
15
15
12

2.5 LPM
15
15
12

1000kPa