Daewoo DTC-25G1VM User manual

Service Manual
Colour Television
CHASSIS: CM-900
Model: DTC-25G1VM (NO TXT)
DTC-29G1VM (NO TXT)
DTC-25G3VMR (NO TXT)
DTC-25G4VMS (NO TXT)
DTC-25G7VM (NO TXT)
DTC-29G1TM (TXT)
DTC-25G1TM (TXT)
DAEWOO ELECTRONICS CO., LTD.
✔ Caution
: In this Manual, some parts can be changed for improving, their
performance without notice in the parts list. So, if you need the
latest parts information,please refer to PPL(Parts Price List) in
Service Information Center (http://svc.dwe.co.kr).





SPECIFICATIONS ................................................................................................................................ 2
SAFETY INSTRUCTIONS .................................................................................................................... 3
BLOCK DIAGRAM ............................................................................................................................... 4
ALIGNMENT INSTRUCTIONS ............................................................................................................. 5
„ CM-900 CHASSIS ADJUSTMENT .................................................................................................... 5
„ SERVICE MODE ................................................................................................................................ 11
„ OTHER SERVICE FUNCTION .......................................................................................................... 12
„ TEST SIGNAL SELECTION .............................................................................................................. 13
„ SERVICE REMOTE CONTROLLER ................................................................................................. 14
PARTS LIST ......................................................................................................................................... 15
DIFFERENCE PARTS LIST ................................................................................................................. 29
PRINTED CIRCUIT BOARDS .............................................................................................................. 31
EXPLODED VIEW
„ DTC-25G1VM .................................................................................................................................... 32
„ DTC-29G1VM .................................................................................................................................... 33
„ DTC-29G3VMR .................................................................................................................................. 34
„ DTC-29G4VMS .................................................................................................................................. 35
„ DTC-2987VM ..................................................................................................................................... 36
SCHEMATIC DIAGRAM ....................................................................................................................... 37


SPECIFICATIONS
STANDARD MODEL DTC-25G1VM DTC-29G1VM
TV STANDARD PAL/SECAM-B/G, D/K, I, H, NTSC-4.43/3.58
Mains Voltage AC 110 - 250V, 50/60Hz
Power Consumption 120W 145W
Sound Output Power 10W + 10W (AT 100% MOD, 10% THD)
Speaker 12W 8 Ohms (Normal) X 2EA
Antenna Impedance 75 Ohm unbalanced (DIN Standard)
Tuning System Voltage Synthesize Tuning System
Number of Program 100 Channels
Reception Channel VHF - L : I1 -S8 CH (43.25 - 154.25MHz)
VHF - H : S9 - S41 CH (161.25 - 463.25MHz)
UHF : C13 - C57 CH (471.25MHz - 863.25MHz)
Remote ControlUnit R-33C
CRT 25 Inch 29 Inch
Weight 33Kg (SET) 45Kg (SET)
Indication Program No. Display
Tuning Voltage Display
Video Input Display
Analog Control Display
(Color, Bright, Contrast, Sharpness, Tint, B/B-Back/Blue)
Volume Control Display
(Bass, Treble, Balance)
PresetDisplay
Clock Display
NTSC state Display
ON/OFF Timer Display
Language Display


SAFETY INSTRUCTIONS
BEFORE SERVICING THIS CHASSIS,READ THE “X-RAY RADIATION PRECAUTION”,
“SAFETY PRECAUTION” AND “PRODUCT SAFETY NOTICE” BELOW.
NOTE
1. Excessive high voltage can produce potentially haz-
ardous X-RAY RADIATION.To avoid such hazards,
the high voltage mustnot exceed the specified limit.
The nominal value of the high voltageof this receiver is
26.5kv(25”),29.5kv(29”) at max beam current.
The high voltage must not,under any circumstances,
exceed 29.0kv (25”), 31.5kv(29”).
Each time a receiver requires servicing,the high
voltage should be checked. It is recommended the
reading of the high voltage recorded as a part of
the service records. it is important to use an accu-
rate and reliable high voltage meter.
2. The only source of X-RAY Radiation in this TV
receiver is the picture tube.
For continuous RADIATION protection, the
replacement tube must be exactly the same type
tube as specified in the parts list.
1.Potentials ofhigh voltage are presentwhen this receiver
is operating. Operation ofthe receiver outside the cabi-
net or with the back cover removed involves a shock
hazard from the receiver.
1) Servicing should not be attempted by anyone who is
notthoroughly familiar with the precautions necessary
when working on highvoltage equipment.
2) Always discharge the picture tube to avoid the shock
hazard before removing the anode cap.
3)Discharge the high potentialof the picture tube before
handling the tube. The picture tube is highly evac
uated and if broken, glass fragments will be violently
expelled.
2. If any Fuse in this TV receiver is blown, replace it with
the FUSE specified in the Replacement Parts List.
3. When replacing a high wattage resistor(oxide metalfilm
resistor) in circuit board, keep the resistor 10mm away
from circuit board.
4. Keep wires away from high voltage or high temperature
components.
5. This receiver must operate between AC110~250volts,
50Hz/60Hz. NEVER connect to DC supply or any other
power or frequency.
Many electricaland mechanical parts in this
chassis have special safety-related characteristics.
These characteristics are often passed unnoticed by
a visual inspection and the X-RAY RADIATION
protection afforded by them cannot necessarily be
obtained by using replacement components rated for
higher voltage, wattage, etc.
Replacement parts which have these specialsafety
characteristics are identified in this manualand its
supplements, electrical components having such fea-
tures are identified by designated symbolon the parts
list. Before replacing any of these components, read
the parts list in this manual carefully.
The use ofsubstitute replacement parts which do not
have the same safety characteristics as specified in
the parts list may created X-RAY Radiation.
X-RAY RADIATION PRECAUTION
SAFETY PRECAUTION
PRODUCT SAFETY NOTICE


BLOCK DIAGRAM


ALIGNMENTINSTRUCTIONS
„
„„
„CM-900 CHASSIS ADJUSTMENT
Application
•
This prescribes the adjustment procedure for the optimum electricalperformance of the CM-900 chassis
color TV receiver
General Description
•
The grade characteristics have to be marked on the testdevices and measuring instruments.
•
Fix these equipments previously which have enough performance to acknowledge the applied standard for each test items.
•
Perform the adjustment when the chassis is in a fully stable state as long as no particular condition is specified.
•
When adjusting this chassis, the environmental temperature 20±2°C, relative humidity 65±5% and air pressure
860-1060mbar are suitable. As long as no particular condition is specified, however, it is possible to execute the
adjustment at temperature 15-35°C, relative humidity 45-85% and air pressure 860-1060mbar.
•
The strength of the applied input signalis dropped out voltage as long as no particular condition is specified.
Power Supply
•
perform the adjustment within ±10% of the rate voltage.
Additional Remark
• In this test, the subject matterof the open/close applies in accordance with the technical standard control rule TESNO-001.
1. PCB ADJUSTMENT
1-1. Channel Presetting
CH MEMORY CH. SYSTEM PATTERN
01 2 PAL -B RETMA
02 4 PAL -B DEM
03 5 PAL -B CROSS HATCH
04 8 PAL -B RED
05 10 PAL -B COLOR BAR
06 12 SECAM -B SECAM-COLOR
07 18 PAL -K RETMA
08 21 PAL -G R,B,W
09 25 PAL -G COLOR BAR
10 31 PAL -I COLOR BAR
11 38 PAL -I DEM
12 51 PAL -I RETMA
13 5 NTSC -M COLOR BAR
14 8 NTSC -M RETMA
15 10 NTSC -M LADY


2. Initializing
- To use only when you change the EEPROM.
- Push the MUTE key of the user remocon, at the same time push the MENU button on the Mask Front. And then it is a
service mode.
- In service mode, as push the RECALL key ofthe user remocon, at the same time push the CH UP button on the Mask
Front. And then it is initialized.
- It is not necessary to product at a factory
- After initializing,turn off and then turn on the power.
- Refer ‘ SERVICE MODE’.
3. Screen Adjustment
- Receive the RETMA signal.
- Push the SCREEN ON key of the Service Remocon and make to be displayed the Horizontalline.
- Do not adjust the color what this line is displayed, but add the other color data until the Horizontal line is white.
At this time to use R,G,B CUT OFF.
- After adjustment the Horizontalline is white, turn the screen VR of FBT until the Horizontalline disappear. (to the left)
- Push SCREEN OFF key ofthe service remocon, it willbe displayed as like ‘Fig.1’.
- Push the NORMAL key or W/B key of service remocon, then ‘Fig.1’ disappear.
4. White Balance Adjustment
- Receive the RETMA signal
- Set allcondition to the NormalI. (Push the NORMAL key of the service remocon.)
- Connect the JIG for white balance adjustment.
- First, adjust high beam. Use G,B GAIN key of the service remocon. (X=288, Y=301 for W/B)
- And then adjust low beam again using R,G,B CUT OFF key.
(At this time, if the high beam is changed, adjust again about two times.)
- If you adjust high beam and low beam at the same time, it is not any problem what is used first, R,G,B CUT OFF or
G,B GAIN key.
0
127
127
127
127
127
- -
M.M
G.G
B.G
R.C
G.C
B.C

<Fig. 1>


5. Vertical / Horizontal Adjustment
- Receive the Retma signal (for PAL system)
- Set allcondition to the NormalI. (Push the NORMAL key of the service remocon.)
5-1. V-CENTER
- Push the V.C(P/N) key of the service remocon, then it is displayed like ‘Fig 2’
- Adjustto use DATA UP/DOWN key so thatthe centerofRetma Pattern may be located in the Verticalcenterofthe CRT
5-2. V-HEIGHT
- Push the V.H(P/N) key of the service remocon, and the cursor indicate V.H(P) (Fig 2).
- Adjust to use DATA UP/DOWN key so that the Height number “9” may be seen at the edge
above or below from the end ofthe CRT.
8
13
0
0
71
71
2
H.P(P)
H.P(N)
V.C(P)
V.C(N)
V.H(P)
V.H(N)
V.L

<Fig. 2>
<Fig. 3>


5-3. V-LINEARITY
- Push the V.L key of the service remocon, and the cursor indicate V.L (Fig 2).
- Adjust to use DATA UP/DOWN key so that the Retma Pattern is the most complete circle.
5-4. H-CENTER
- Push the H.P(P) key ofthe service remocon, and the cursor indicate H.P(P) (Fig 2).
- Adjust to use DATA UP/DOWN key so thatthe Width number at the edge of left/ right side may be seen the same.
6. Pincusion Adjustment
- Receive the CROSS-HATCH signal.
- Turn E/W VR(R401) of the main PCB so thatthe second verticalline of the left side may be straightened. (like Fig.4)
7. Width Adjustment
- Receive the Retma signal (for PAL system)
- Turn VR(R402) of the main PCB so that the Width number “11” may be seen at the edge ofleft and right side.
(like Fig.3)
(SECOND VERTICAL LINE)
<Fig. 4>


8. Secam Bell Filter Adjustment
- Receive the SECAM Color Bar signal
- Connect JIG to the Pin No.36 of TB1226N(I501)
- Push the SECAM key of the service remocon, then it is displayed like ‘Fig 5’
- Move the cursor at B.F with ITEM key ofthe service remocon.
- Adjust to use DATA UP/DOWN key so that the wave form may be flat like Fig.6
AB
AB
AB
BEFORE ADJUSTMENT AFTER
13
8
2
- -
- -
- -
- -
R.Y
B.Y
B.F

<Fig. 5>
<Fig. 6>


9. Secam White Balance Adjustment
- Receive the SECAM Color Bar signal
- Connect JIG to the Pin No.35 of TB1226N(I501)
- Push the SECAM key of the service remocon, then it is displayed like ‘Fig 5’
- Move the cursor at R-Y with ITEM key of the service remocon.
- Adjust ‘A’,’B’ block is flat with ‘C’ using DATA UP/DOWN key like Fig 7.
- Move the JIG to the Pin No.36 ofTB1226N (I501).
- Move the cursor at B-Y with ITEM key of the service remocon
- Adjust ‘A’,’B’ block is flat with ‘C’ using DATA UP/DOWN key like Fig 7.
ABC
<Fig. 7>


„
„„
„SERVICE MODE
1.ENTERING TO SERVICE MODE (USE USER REMOTE CONTROL)
1) Press button once on Remote control. 2) Press button again to keep pressing.
3) Press MENU button on TV set, at the same time to keep pressing the button
2. Selection the adjusting items
Every pressing of channel

button changes the adjustment items in the following order
(

button for reverse order )
3. Adjusting the DATA
Pressing of volume

(

) or

(

) will change the value ofdata.
4. EXIT from service mode
Press POWER button to turn off the TV once.
R.C

Red Cutoff
127
127
127
127
127
1
13
R.C
G.C
B.C
G.G
B.G
B.F
R-Y
(Service mode display)
Data adjustingHorizontal line on/off The adjusting item
PR
MENU
RECALL key
(in the Remote
control)
PR

(in the TV Front
Panel)
Initialization of the Memory
(I701)
(Keep pressing the
Recal Button) (Press the ‘PR

'

button)


„
„„
„OTHER SERVICE FUNCTION
The following function key entry during display of adjustment menu provides special functions

Test signal selection

Horizontal line ON/OFF

The adjusting item selection

-/+ Data adjust
4
3
4
3
1
2
1
3
4
2
(TXT) (NO TXT)


„
„„
„TEST SIGNAL SELECTION
Every pressing of AV MIX button changes the testpatterns on screen as descriked below.
ITEM Adjustment procedure
Horizontal position
adjustment
P (P) : PAL
H.P (N) : NTSC
Vertical center
adjustment
C (P) : PAL
H.C (N) : NTSC
1. Set the TV in service mode and get black
or white cross-bar signal with video button
remote hard unit.
2. Select either H.P or V.C with PR
 , 
buttons and adjust horizontal or vertical
picture position in the center of screen
with volume
 ,  buttons.
Vertical amplitude
adjustment
H (P) : PAL
V.H (N) : NTSC
1. Black or white cross-hatch
2. HIT
 V.H
CHANNEL
 PR
Width adjustment
R402 (only PAL)
Pincushion adjustment
R401( only PAL)
1. Set the TV in service mode and get black
or white cross-hatch signal with video
button on remote hard unit.
2. Turn VR(R402) of the main PCB so that
the first vertical line may be placed at
2cm from the edge of left side.
3. Turn E/W VR(R401) of the main PCB
so that the second vertical line of the left
side may be straightened.
The first
The first The second
2cm 1cm
Signaloff PAL signals ( 14 patterns )
NTSC signals ( 14 patterns )


„
„„
„SERVICE REMOTE CONTROLLER
- Adjust whole service function withoutusing user remote controller.
- The following box explains specialkeys.
KEY OPERATION
POWER To turn TV on/off
TTX To select teletext
SEARCH STOP To stop searching Channel
SCREEN ON/OFF To make the Horizontal line
DATA (</>) To change the directed data
V.C(P/N) To adjust Vertical Cente.
(P/N : PAL/NTSC)
V.H(P/N) To adjust Vertical Height
H.P(P/N) To adjust HorizontalPosition
V.L(P/N) To adjust Vertical Linearity
SECAM To adjust SECAM
ITEM(+/-) To move the directed cursor
DATA(+/-) To change two kinds of data
(PAL&NTSC)
PAGE(+/-) To turn a page in a Factory mode
FACTORY To select a Factory mode


PARTS LIST
LOC. PART CODE PART NAME PART DESCIRPTION
ZZ100 48B2833C03 TRANSMITTER REMOCON R-33C03
ZZ110 PTACPWC971 ACCESSORY AS DTC-29G1VM
20 4850A00150 TRANS ANT MATCHING IMT-02
40 485869 MANUAL INSTRUCTION DTC-29G1VM
100 47P7500001 BATTERY AAM 1.5V
M822 48582138 BAG INSTRUCTION L.D.P.E T0.05X250X400
ZZ120 PTBCSHC971 COVER BACK AS DTC-29G1VM
M211 4852150422 COVER BACK HIPS BK
M541 48554158 SPEC PLATE 150ART P/E FILM (C/TV)
M782 485781763 CLOTH BLACK FELT T0.7 L=400
M783 485781761 CLOTH BLACK FELT T0.7 L=300
ZZ130 PTPKCPC971 PACKING AS DTC-29G1VM
M641 65200101 STAPLE PIN 18M/M J D O
M681 48568124 BAND 18MM X 3M
M801 485805225K BOX CARTON DW-3
M811 48581839 PAD EPS 29G1
M821 48582156 BAG P.E PE FOAM T0.5X1550X1270
ZZ131 58G0000094 COIL DEGAUSSING DC-2901
ZZ132 48519A4210 CRT GROUND NET 2901H-1015-2P
ZZ140 PTCACAC971 CABINET AS DTC-29G1VM
M191 485192961 BUTTON CTRL 4936410 5533900
M191A 7128301212 SCREW TAPPING T2S WAS 3X12 MFZN BK
M201A 485601582 SCREW CRT FIX SWRM SK5 L=35
M201B 4856215402 WASHER RUBBER CR
M211A 7122401612 SCREW TAPPING T2S TRS 4X16 MFZN BK
M211B 7128301212 SCREW TAPPING T2S WAS 3X12 MFZN BK
M211C 7122401612 SCREW TAPPING T2S TRS 4X16 MFZN BK
M481 4854851901 BUTTON POWER ABS BK
M481A 4856716 SPRING SWPA PIE0.5
M561 48556174SD MARK BRAND SILVER DIA-CUTTING
M682 48568163 CLAMP WIRE NYLON 6 (V0)
M781 4857821102 CLOTH BLACK FELT 340X10XT1.68
SP01A 7122401412 SCREW TAPPING T2S TRS 4X14 MFZN BK
V901 485961806 CRT A68KTB190X006 P38
ZZ200 PTFMSJC971 MASK FRONT AS DTC-29G1VM
M201 4852064901 MASK FRONT HIPS BK
ZZ202 PTSPPWC971 SPEAKER AS DTC-29G1VM
M681 4856812001 TIE CABLE NYLON66 DA100
SP01 48A8304700 SPEAKER SYSTEM SS-58126F01
ZZ290 PTMPMSC971 PCB MAIN MANUAL AS DTC-29G1VM
C310 CEXF1V332V C ELECTRO 35V RSS 3300MF 18X35.5
C322 CEYF1V222V C ELECTRO 35V RSS 2200MF (16X31.5)
C401 CMYB2G514K C MYLAR 400V EU 0.51MF K
C403 CMYH3C822J C MYLAR 1.6KV BUP 8200PF J
C404 CMYH3C822J C MYLAR 1.6KV BUP 8200PF J
✔ Caution:In this Service Manual, some parts can be changed for improving, their performance without notice in the parts list. So, if you need the
latest parts information, please refer to PPL(Parts Price List) in Service information Center(http://svc.dwe.co.kr)


C411 CEYD1H689V C ELECTRO 50V RUB 6.8MF (16*35.5)
C413 CEYF2C221C C ELECTRO 160V RUS 220MF (18X35.5)
C427 CMXM2A104J C MYLAR 100V 0.1MF J (TP)
C801 CL1JB3474K C LINE ACROSS AC250V 0.47MF U/C/SNDF/SV
C812 CH1FFE222M C CERA AC 4.0KV 2200PF M KD AC250V
C813 CEYN2G331P C ELECTRO 400V LHS 330MF (30X45)
C814 CH1AEE472M C CERA AC 2.5KV 4700PF M KH DE1307
C820 CBYB3D152K C CERA SEMI 2KV BL(N) 1500PF K
C836 CEYN2D221T C ELECTRO 200V FWS 220MF (22X30)
C842 CEYF1H222C C ELECTRO RUS 50V 2200MF 18*35.5
C843 CEYF1H222C C ELECTRO RUS 50V 2200MF 18*35.5
D401 DDG3------ DIODE DG3
D402 DRGP30J--- DIODE RGP30J
D444 DDG3------ DIODE DG3
D706 DKLR114L-- LED KLR114L
D801 PTA1SW5801 HEAT SINK ASS`Y DPBS606GU- 7174301011
D801 DPBS606GU- DIODE BRIDGE PBS606GU
D801A 4857015801 HEAT SINK SPCC-SN T1.0
D801B 7174301011 SCREW TAPPTITE TT2 RND 3X10 MFZN
D811 DBYT56K--- DIODE BYT56K
D812 DBYT56K--- DIODE BYT56K
D815 DRGP30J--- DIODE RGP30J
F801 5F3GB6322L FUSE GLASS TUBE V/S TL 6.3A 250V MF51
I301 PTA2SW6104 HEAT SINK ASS`Y 1TA8427K-- 7174301011
I301 1TA8427K-- IC TA8427K
I301A 4857026104 HEAT SINK AL EX BK
I301B 7174301011 SCREW TAPPTITE TT2 RND 3X10 MFZN
I302 1EW------- IC HYBRID E/W
I501 1TB1226BN- IC TB1226BN
I502 1K1A7812P1 IC REGULATOR KIA7812PI
I503 1K1A7809-- IC REGULATOR KIA7809
I601 PTA2SW3332 HEAT SINK ASS`Y 1LA4282--- 7128301011
11LA4282--- IC LA4282
0000A 4857023332 HEAT SINK AL EX
0000B 7128301011 SCREW TAPPING T2S WAS 3X10 MFZN
I602 1TDA8424-- IC AUDIO TDA8424
I603 1SN76861NJ IC SN76861NJ-12
I701 1TMP87PS38 IC MICOM TMP87PS38N
I702 124LC08B-- IC MEMORY 24LC08B
I704 PTH2SW6900 HEAT SINK ASS`Y 1KA7805--- 7174301011
11KA7805--- IC REGULATOR KA7805
0000A 48570269 HEAT SINK AL EX
0000B 7174301011 SCREW TAPPTITE TT2 RND 3X10 MFZN
I705 1TFMW5380- IC PREAMP TFMW5380
I801 PTL2SW6500 HEAT SINK ASS`Y 1STR6708-- 7174301211
LOC. PART CODE PART NAME PART DESCIRPTION


I801 1STRS6708- IC POWER STR-S6708
I801A 48570265 HEAT SINK AL EX
I801B 7174301211 SCREW TAPPTITE TT2 RND 3X12 MFZN
I802 1SE130N--- IC SE130N
I805 1LTV817C-- IC PHOTO COUPLER LTV-817C
JV02 485910845 JACK PIN BOARD YSC03P-4120-14A
JV03 485910705 JACK PIN BOARD PH-JB-9601 (PH06P-4120-C)
L401 58H0000039 COIL H-LINEARITY TRL-200D
L402 58W0000018 COIL WIDTH TLN-2092
L404 58C7070085 COIL CHOKE TLN-3062A
L801 5PLF30A1-- FILTER LINE LF-30A1
L811 58C4500079 COIL CHOKE L-45
L812 58C4500079 COIL CHOKE L-45
M352 4853530901 HOLDER LED P.P
M371 48537478 RETA PCB NYLON 66
M681 4856812001 TIE CABLE NYLON66 DA100
P401 485924012 CONN WAFER YFW500-06
P801 485924222 CONN WAFER YFW800-02
P802 485924222 CONN WAFER YFW800-02
P802A 485990291 CORD POWER AS KKP419C BL102NG TUBE=2100
A000 4859901111 CORD POWER KKP-419C KLCE-2F (2.1ME)
Q401 TKTC3208-- TR KTC3208
Q402 PTL2SW4502 HEAT SINK ASS`Y T2SD2251-- 7174301011
Q402 T2SD2251-- TR 2SD2251
Q402A 4857024502 HEAT SINK AL EX
Q402B 7174301211 SCREW TAPPTITE TT2 RND 3X12 MFZN
Q402D 4856215201 WASHER SPCC
Q403 PTM2SW4502 HEAT SINK ASS`Y TKTD2058Y- 7174301211
Q403 TKTD2058Y- TR KTD 2058-Y
Q403A 4857024502 HEAT SINK AL EX
Q403B 7174301211 SCREW TAPPTITE TT2 RND 3X12 MFZN
Q403C 4856215201 WASHER SPCC
Q801 T2SC4793-- TR 2SC4793
Q802 TKTA1659Y- TR KTA 1659-Y
R407 RX10T402J- R CEMENT 10W 4K OHM J TRIPOD
R431 DR320K---- THERMISTOR R-320K
R801 DJ140M290L POSISTOR J503P53D140M290L
R802 RX10T109J- R CEMENT 10W 1 OHM J TRIPOD
R803 RX10T109J- R CEMENT 10W 1 OHM J TRIPOD
R812 RM02Y158J- R METAL FLAT 2W 0.15 OHM J
SW801 5S40202080 SW PUSH PS3-22 (PCB)
T401 5TD0000018 TRANS DRIVE THD-120
T402 50H0000168 FBT FFA94024L
T402A 7128301212 SCREW TAPPING T2S WAS 3X12 MFZN BK
T802 50M5345A60 TRANS SMPS TSM-5345A6
LOC. PART CODE PART NAME PART DESCIRPTION


TU01 485971723 TUNER VARACTOR UHF111
W001 WBNZBK2515 WIRE LEAD 1617 AWG22 17/0.16 BK 5-250-5
X501 5XE16R200E CRYSTAL QUARTZ HC-49/U 16.20000MHZ 30PPM
X701 5XE8R0000E CRYSTAL QUARTZ HC-49/U 8.000000MHZ 30PPM
Y801 5SC0101327 SW RELAY DJ12D1-0(M)-0.25W
Z801 DSVC471D14 VARISTOR SVC471D14A
ZZ200 PTMPJ0C971 PCB MAIN (RHU) AS DTC-29G1VM
C402 CMXB2D683J C MYLAR 200V EU 0.068MF J (TP)
C405 CMXE2G273J C MYLAR 400V PU 0.027MF J (TP)
C410 CEXF1H101V C ELECTRO 50V RSS 100MF (8X11.5) TP
C416 CEXF1V102V C ELECTRO 35V RSS 1000MF (13X25) TP
C426 CEXF1E222C C ELECTRO 25V RUS 2200MF (16X25) TP
C472 CEXF1E102V C ELECTRO 25V RSS 1000MF (13X20) TP
C473 CEXF1E471V C ELECTRO 25V RSS 470MF (10X16) TP
C477 CEXF1E471V C ELECTRO 25V RSS 470MF (10X16) TP
C651 CEXF1V102V C ELECTRO 35V RSS 1000MF (13X25) TP
C652 CEXF1V102V C ELECTRO 35V RSS 1000MF (13X25) TP
C659 CEXF1E102V C ELECTRO 25V RSS 1000MF (13X20) TP
C663 CEXF1H102V C ELECTRO 50V RSS 1000MF (16X25) TP
C691 CEXF1C222V C ELECTRO 16V RSS 2200MF (13X25) TP
C714 CEXF1C102V C ELECTRO 16V RSS 1000MF (10X20) TP
C772 CEXF1C222V C ELECTRO 16V RSS 2200MF (13X25) TP
C773 CEXF1E471V C ELECTRO 25V RSS 470MF (10X16) TP
C811 CEXF1E471V C ELECTRO 25V RSS 470MF (10X16) TP
C831 CCXB3A102K C CERA 1KV B 1000PF K (TAPPING)
C838 CEXF2C100C C ELECTRO 160V RUS 10MF (10X16)TP
C841 CEXF1E222C C ELECTRO 25V RUS 2200MF (16X25) TP
ZZ200 PTMPJBC971 PCB MAIN M-10 AS DTC-29G1VM
P402 485923162S CONN WAFER YW025-03 (STICK)
P403 485923182S CONN WAFER YW025-05 (STICK)
P601 485923172S CONN WAFER YW025-04 (STICK)
R321 RF01Z109J- R FUSIBLE 1W 1 OHM J (TAPPING)
R403 RS01Z102J- R M-OXIDE FILM 1W 1K OHM J (TAPPING)
R410 RS02Z183JS R M-OXIDE FILM 2W 18K OHM J SMALL
R423 RF01Z109J- R FUSIBLE 1W 1 OHM J (TAPPING)
R491 RF01Z109J- R FUSIBLE 1W 1 OHM J (TAPPING)
R492 RF02Z439J- R FUSIBLE 2W 4.3 OHM J (TAPPING)
R691 RS01Z390J- R M-OXIDE FILM 1W 39 OHM J (TAPPING)
R831 RF02Z278J- R FUSIBLE 2W 0.27 OHM J (TAPPING)
R832 RF01Z338J- R FUSIBLE 1W 0.33 OHM J (TAPPING)
R833 RF01Z688J- R FUSIBLE 1W 0.68 OHM J (TAPPING)
R836 RS01Z681J- R M-OXIDE FILM 1W 680 OHM J (TAPPING)
ZZ200 PTMPJRC971 PCB MAIN RADIAL AS DTC-29G1VM
C301 CMXL1J104J C MYLAR 63V MEU 0.1MF J
C304 CMXM2A223J C MYLAR 100V 0.022MF J TP
LOC. PART CODE PART NAME PART DESCIRPTION


C306 CEXF1E221V C ELECTRO 25V RSS 220MF (8X11.5) TP
C307 CMXM2A102J C MYLAR 100V 1000PF J (TP)
C308 CEXF1H229V C ELECTRO 50V RSS 2.2MF (5X11) TP
C311 CCXF1H103Z C CERA 50V F 0.01MF Z (TAPPING)
C321 CCXB2H102K C CERA 500V B 1000PF K (TAPPING)
C351 CEXF1H229V C ELECTRO 50V RSS 2.2MF (5X11) TP
C352 CCXB1H152K C CERA 50V B 1500PF K (TAPPING)
C406 CCXB2H271K C CERA 500V B 270PF K (TAPPING)
C408 CCXB2H102K C CERA 500V B 1000PF K (TAPPING)
C409 CCXF2H103Z C CERA HIKF 500V 0.01MF Z
C412 CEXF1H470C C ELECTRO 50V RUS 47MF (6.3X11) TP
C414 CMXL1J104J C MYLAR 63V MEU 0.1MF J
C415 CMXL1J104J C MYLAR 63V MEU 0.1MF J
C417 CMXB1H563J C MYLAR 50V EU 0.056MF J (TP)
C422 CMXM2A472J C MYLAR 100V 4700PF J (TP)
C423 CCXB2H271K C CERA 500V B 270PF K (TAPPING)
C424 CCXB2H102K C CERA 500V B 1000PF K (TAPPING)
C425 CCXB1H681K C CERA 50V B 680PF K (TAPPING)
C428 CMXM2A103J C MYLAR 100V 0.01MF J (TP)
C451 CMXL1J334J C MYLAR 63V MEU 0.33MF J (TP)
C452 CEXF1H229V C ELECTRO 50V RSS 2.2MF (5X11) TP
C453 CCXB1H221K C CERA 50V B 220PF K (TAPPING)
C454 CCXF1H103Z C CERA 50V F 0.01MF Z (TAPPING)
C471 CCXF1H103Z C CERA 50V F 0.01MF Z (TAPPING)
C474 CCXF1H103Z C CERA 50V F 0.01MF Z (TAPPING)
C475 CCXF1H103Z C CERA 50V F 0.01MF Z (TAPPING)
C476 CCXF1H103Z C CERA 50V F 0.01MF Z (TAPPING)
C491 CCXB2H102K C CERA 500V B 1000PF K (TAPPING)
C501 CCXF1H103Z C CERA 50V F 0.01MF Z (TAPPING)
C502 CCXF1H103Z C CERA 50V F 0.01MF Z (TAPPING)
C503 CEXF1E470V C ELECTRO 25V RSS 47MF (5X11) TP
C504 CEXF1H229V C ELECTRO 50V RSS 2.2MF (5X11) TP
C505 CCXF1H103Z C CERA 50V F 0.01MF Z (TAPPING)
C506 CEXF1E470V C ELECTRO 25V RSS 47MF (5X11) TP
C507 CEXF1H479V C ELECTRO 50V RSS 4.7MF (5X11) TP
C508 CMXB1H104J C MYLAR 50V EU 0.1MF J (TP)
C509 CMXM2A103J C MYLAR 100V 0.01MF J (TP)
C510 CEXF1H229V C ELECTRO 50V RSS 2.2MF (5X11) TP
C511 CMXL1J104J C MYLAR 63V MEU 0.1MF J
C512 CMXL1J104J C MYLAR 63V MEU 0.1MF J
C513 CMXL1J104J C MYLAR 63V MEU 0.1MF J
C514 CCXF1H103Z C CERA 50V F 0.01MF Z (TAPPING)
C515 CEXF1H100V C ELECTRO 50V RSS 10MF (5X11) TP
C516 CEXF1H109V C ELECTRO 50V RSS 1MF (5X11) TP
C517 CEXF1E101V C ELECTRO 25V RSS 100MF (6.3X11) TP
LOC. PART CODE PART NAME PART DESCIRPTION