Daewoo DWD-FT1081 User manual

Service Manual
Washing Machine
Model: DWD-FT1081/FT1082/FT1083
DWD-FT1281/FT1282/FT1283
DAEWOO ELECTRONICS CORP.
S/M No. :
http : //svc.dwe.co.kr May. 2011
✔Caution
: In this Manual, some parts can be changed for improving,
their performance without notice in the parts list. So, if you
need the latest parts information, please refer to PPL(Parts
Price List) in Service Information Center (http://svc.dwe.co.kr).

AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER
AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER
AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER
AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER
AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER
AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER
AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER
AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER
AUTO WASHER
WASHING MACHINE
Contents
1. SPECIFICATIONS....................................................................................................................2
2. INSTALLATION .......................................................................................................................3
Transit bolts.......................................................................................................................3
Removing transit bolts ......................................................................................................3
Installation place requirement...........................................................................................4
BS Plug Safety Details (For U.K. User)............................................................................4
Connecting inlet hose .......................................................................................................5
Installation of drain hose...................................................................................................6
Level adjustment...............................................................................................................7
3. MAINTENANCE.......................................................................................................................8
Cleaning your washer .......................................................................................................8
Cold condition ...................................................................................................................8
Cleaning the water inlet filter ............................................................................................9
Cleaning the drain pump filter...........................................................................................9
Cleaning the detergent case...........................................................................................10
Cleaning the washing drum ............................................................................................10
4. DIRECTION FOR DISASSEMBLY........................................................................................11
5. EXPLODE VIEW AND PARTS LIST.....................................................................................14
6. FUNCTIONS OF THE CONTROL PANEL............................................................................23
7. FUNCTIONS OF THE CONTROLLER..................................................................................24
8. FUNCTION OF THE CONVENIENT SERVICE.....................................................................27
9. TROUBLESHOOTING GUIDE..............................................................................................28
10. WIRING DIAGRAM..............................................................................................................32

1. SPECIFICATIONS
2
SPECIFICATIONS
■ Accessories
DETERGENT CASE
INLET HOSE
HOT
(OPTION) COLD
DOOR
LOWER COVER ADJUSTABLE LEG
HOSE DRAIN
CONTROL PANEL
POWER CORD
Dimension (mm)
Maximum mass of texile (kg)
Unit Weight (kg)
Standard Water Consumption
Spin Speed (RPM)
Operating Water Pressure
595 x 590 x 850 (W x D x H)
7.0 / 8.0
49(Net) / 52(Gross)
50~60ℓ
400 / 800 / 1000 or 1200
0.03MPa ~ 0.8MPa (0.3kgf/cm2~ 8kgf/cm2)
MODEL DWD-FT1081/FT1082/FT1083
DWD-FT1281/FT1282/FT1283
Inlet hose Manual Cap holder(3EA)

2. INSTALLATION
3
INSTALLATION
■ Transit bolts
The appliance is fitted with transit bolts to prevent internal damage during transport.
■ Removing transit bolts
1. To prevent internal damage during transport, the
special 3 bolts are locked. Before operating the
washer, remove the bolts along with the rubber
bungs.
• If they are not removed, it may cause heavy
vibration, noise and malfunction.
2. Unscrew the 3 bolts with the spanner supplied,
and take out the 3 bolts with the rubber bungs.
Keep the 3 bolts and the spanner for future use.
• Whenever the appliance is transported, the
transit bolts must be refitted.
3. Close the holes with the caps supplied.

4
INSTALLATION
■ Installation place requirement
■ BS Plug Safety Details (For U.K. User)
Level floor :
Allowable slope under entire washer is 1°.
Power outlet :
Must be with 1.5 meters of entire side of location of
washer. Do not overload the outlet with more than
one appliance.
Additional Clearance :
For wall, door and floor modeling is required.
(10cm : rear / 2cm : right & left side)
Do not place or store laundry products on top of
washer at any times.
They can damage the finish or controls.
As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings
identifying the terminals in your plug, proceed as follows:
The wire which is coloured Green and Yellow must be connected to the terminal in the plug which is marked
with the letter E or by the earth symbol or coloured Green or Green and Yellow.
The wire which is coloured Blue must be connected to the terminal which is marked with the letter N or coloured Black.
The wire which is coloured Brown must be connected to the terminal which is marked with the letter L or
coloured Red.
If a 13 amp (BS 1363) plug is used, fit a 13amp BS 1362 fuse.
IMPORTANT
THE WIRES IN THIS MAINS LEAD ARE COLOURED IN ACCORDANCE WITH THE FOLLOWING CODE:
GREEN AND YELLOW : EARTH
BLUE : NEUTRAL
BROWN : LIVE
This appliance must be earthed

5
INSTALLATION
FOR ORDINARY TAP
6Connect the inlet hose
adapter of the hose to the
water inlet of the washer by
turning it clockwise to be fixed
tightly.
• Please check the rubber
packing present inside the inlet
hose adapter of the hose.
1Pull down the collar
of the inlet hose to
separate it from the
water tap adapter.
2Loosen the four
screws properly in
order to fit into
water tap.
4Remove the tape,
and screw connector
B into connector A
tightly.
5Connect the inlet
hose to the water tap
adapter by pulling down
the collar of the hose
end.
3Fit the water tap adapter into
the water tap and tighten the
four screws evenly while
pushing up the adapter so that
the
rubber packing can stick to the
water tap tightly.
■ Connecting inlet hose
In using only one water tap or in case of only one water inlet valve, connect the inlet hose to the cold water inlet valve.
Option : Be careful not to confuse hot water inlet and cold water inlet.
FOR SCREW-SHAPED TAP
3 Connect the inlet hose adapter
to the water inlet of the washer
and turn it to be fixed.
• Check the packing in the inlet.
1Connect the inlet hose
to the water tap
adapter by pulling
down the collar of the
hose end.
2 Connect the
connector- inlet
supplied if
necessary.
Inlet Hose
Connector D
Rubber˜
Packing
Connector C
Connector˜
Inlet˜
˜
Rubber˜
Packing
Connector D
Connector C
Hose
TAPE
Connector B
Connector A

6
INSTALLATION
■ Installation of drain hose
• When installing the drain hose in sink, secure
it tightly with a string.
• Proper securing of the drain hose will protect the
floor from damage due to water leakage.
• The drain hose should not be placed higher than
100cm above the floor.
• Proper securing of the drain hose will protect the
floor from damage due to water leakage.
• When the drain hose is too long, do not force
back in to the washer. This will cause
abnormal noise.
■ Installation of drain hose

7
INSTALLATION
■ Level adjustment
1. The level adjustment of the washing machine
prevents excessive noise and vibration.
Install the washing machine on a solid and even
floor surface, if possible, in a corner of the room.
Note: The wooden floor may cause excessive
vibration.
2. If the floor is uneven, adjust the adjustable leg as
the following.
(Do not insert pieces of wood etc. under legs.)
• Please check whether there is any gap between
four adjustable legs and the floor.
• Turn adjustable legs by the enclosed spanner in
order to adjust the level of the washing machine.
• Make it sure that there is no swaying of the
washing machine and check that the washing
machine is even completely. (use a spirit level)
• After the level adjustment is finished, turn fixing
nuts up tightly so that the washing machine
maintains the adjustment.
leg
leg
Fixing Nut
❈ Diagonal Check
When pushing down the edges of the washing
machine top plate diagonally, the machine should
not move up and down at all.
(Please, check both of two directions)
If machine rocks when pushing the machine top
plate diagonally, adjust legs again.

3. MAINTENANCE
8
MAINTENANCE
❈Before cleaning the washer interior, unplug the electrical power cord avoid electrical shock hazards.
■ Cleaning your washer
1. Exterior
Proper care of your washer can extend its life.
The outside of the machine can be cleaned with warm water and a neutral non abrasive household detergent.
Immediately wipe off any spills. Wipe with damp cloth.
Try not to hit surface with sharp objects.
• Do not use methylated spirits, diluents or similar products.
2. Interior
Dry around the washer door opening, flexible gasket and door glass.
Run washer through a complete cycle using hot water.
Repeat process if necessary.
• Remove hard water deposits using only cleaners labeled as washer safe.
■ Cold condition
If the washer is stored in an area where freezing may occur or moved in freezing temperature,
follow these instructions to prevent damage to the washer.
1. Turn off water supply tap.
2. Disconnect hoses from water supply and drain water from hoses.
3. Plug electrical cord into a properly grounded electrical outlet.
4. Add 1gallon(3.8L) of nontoxic recreational vehicle(RV) antifreeze into empty wash drum.
Close the door.
5. Set spin cycle and let washer spin for 1minute to drain out all water.
6. Unplug eletrical power cord, dry the drum interior, and close the door.
7. Remove detergent case and dry excessive water from the compartments.
8. Store washer in an upright position.
9. To remove antifreeze from washer after storage, run empty washer through a complete cycle using detergent.
Do not add wash load.

9
MAINTENANCE
■ Cleaning the water inlet filter
• "IE" error message will blink on the control panel when water does not enter the detergent drawer.
• If your water is very hard or contains traces of lime deposit, the water inlet filter may become clogged.
• It is therefore a good idea to clean it from time to time.
■ Cleaning the drain pump filter
• The drain filter collects threads and small objects left in the laundry.
• Check regularly that the filter is clean to ensure smooth running of your machine.
CAUTION Be careful when draining if the water is hot.
1. Turn off the
water tap.
2. Unscrew the
water inlet
hose.
3. Clean the filter
using a had
bristle brush.
4. Tighten up the
inlet hose.
1. Open the lower cover(1) by
using a coin. Turn the cap
hose(2) to pull out the hose.
Pull out the hose maximally.
(About 13~14cm.)
2. Unplug the cap hose(2), allowing
the water to flow out. At this time use
a vessel to prevent water flowing on
to the floor. When water does not
flow any more, turn the pump
filter(3) open to the left.
3. Remove any foreign material
from the pump filter(3). After
cleaning, turn the pump filter
clockwise and insert the cap
hose(2) to the original place.
Close the lower cover.
1
100
2
3
about
13~14cm
23
about
13~14cm
■ Cleaning the water inlet filter
• "IE" error message will blink on the control panel when water does not enter the detergent drawer.
• If your water is very hard or contains traces of lime deposit, the water inlet filter may become clogged.
• It is therefore a good idea to clean it from time to time.

10
MAINTENANCE
■ Cleaning the washing drum
• If you live in a hard water area, limescale may continuously build up in places where it cannot be seen and thus
not easily removed.
• Over time the build up of scale clogs appliances, and if it is not kept in check these may have to be replaced.
• Although the washing drum is made of stainless steel, specks of rust can be caused by small metal articles (paper
clips, safety pins) which have been left in the drum.
• The washing drum should be cleaned from time to time.
• If you use descaling agents, dyes or bleaches, make sure they are suitable for washing machine use.
❈Descaler may contain chemicals that may damage part of your washing machine.
❈Remove any spots with a stainless steel cleaning agent.
❈Never use steel wool.
■ Cleaning the detergent case
• In case of residual detergents or fabric softeners have accumulated ;
- It should be cleaned with a jet of running water.
- If necessary, it can be removed completely from the washing machine.
• Detergents can be also accumulate the inside cavity.
In this case, the inside cavity should be cleaned with a brush.
• After cleaning, replace the detergent case and run Rinse cycle without laundry.
Push point
1Pull-out
2Push and pull again

4. DIRECTION FOR DISASSEMBLY
11
DIRECTION FOR DISASSEMBLY
DOOR LOCK SWITCH
1) Open the door and remove the gasket clamp. 2) Remove the gasket from the front cabinet.
HEATER AND THERMISTOR
1) Remove four screws on the back cover, and
remove the back cover.
2) Remove connectors and the earth terminal.
3) Remove two screws, and remove the door lock
switch.

12
DIRECTION FOR DISASSEMBLY
3) Remove the nut by using a box wrench, and
remove the earth terminal.
4) Loosen the nut by using a box wrench, and pull out
the heater.
UNIVERSAL MOTOR
1) Remove the belt from the pulley. 2) Lay the right side of the washer on the floor,
and remove the connector.
3) Remove two bolts mounting the motor by using a box
wrench.
4) Remove the motor from the tub.

13
DIRECTION FOR DISASSEMBLY
DRAIN PUMP
1) Lay the right side of the washer on the floor, and
remove the lower panel by pressing six sanp fits.
2) Remove connectors.
3) Remove the screw, and remove the drain pump from
the lower frame.
4) Remove the drain hose.
5) Remove the inner drain hose, and remove the drain
pump.

5. EXPLODE VIEW AND PARTS LIST
14
EXPLODE VIEW AND PARTS LIST
■ BOX INLET AS
A01 CASE HANDLE 36111T2W00 HIPS, FT1081 1
-ABS + SPRAY, FT1081 1
A02 CASE DETERGENT 3611145800 PP 1
A03 CAP SOFTENER 3610907800 PP 1
A04 INLET BOX 3617511800 PP, D-FU1081 1
A05 NOZZLE UNDER 3618103410 PP 1 M’S
A06 NOZZLE TOP 3618112200 PP, Cold only 1
3618112210 PP, Cold + Hot 1
A07 HOSE WATER SUPPLY 3613270900 EPDM,ID9.5,OD14.5, L=310 2(3) COLD(+HOT)
A08 CLAMP HOSE 3611205800 100H,ID=13.8,W=10,0.9T 4(6) COLD(+HOT)
A09 VALVE INLET 3615414900 220~240V, 2-WAY, PP/BRACKET 1 COLD
3615416821 220~240V, VDE,2-WAY+DR TECH INSPECTION COST COLD(EU)
3615414800 220~240V, 1-WAY, HOT PP/BRACKET 1 HOT(OPTION)
A10 SCREW TAPTITE 7272400811 TT3, TRS 4X8 MFZN 2(4) COLD(+HOT)
A11 SCREW TAPPING 7122401411 T2S,TRS, 4X14 MFZN 1
A12 HOSE INLET 3613276600 EPDM, FT1081 1
A13 CLAMP HOSE 3611201401 HSW3,YW,D2.6,ID36,W44.5 1
No. PART NAME PART CODE SPECIFICATION Q'TY REMARK

15
EXPLODE VIEW AND PARTS LIST
■ PANEL FRONT AS
F01 PANEL F 36142T3A00 HIPS, FT1081 1
F02 BUTTON P.S 3616647600 ABS, FT1081 1
F03 WINDOW DISPLAY 3615511700 ABS(TR), FT1081 1
F04 DECO DIAL 36166DGQ00 ABS, FT1081 1
F05 KNOB DIAL 3616647700 ABS, FT1081 1
F06 SHAFT KNOB 3614905700 POM, MU802'S 1
F07 CASE PCB F 36111T2X00 HIPS, FT1081 1
F08 PCB AS PRPSSWB--- DWD-F1XXX SERIES 1
F09 SCREW TAPPING 7122300811 T2S TRS 3X8 3
F10 SCREW TAPPING 7122401411 T2S TRS 4X14 4
No. PART NAME PART CODE SPECIFICATION Q'TY REMARK
Refer to
Detailed Part Code
of PCB AS

16
EXPLODE VIEW AND PARTS LIST
■ Detailed Part Code of PCB AS
PRPSSWB700 D-FT1081 MAIN PCB AS, VE+NON-VDE, BB, HOT+COLD, 1000RPM
PRPSSWB701 D-FT1081 MAIN PCB AS, VE+NON-VDE, NON-BB, COLD, 1000RPM
PRPSSWB702
D-FT1081 MAIN PCB AS, VE+NON-VDE, BB, COLD, 1000RPM
PRPSSWB703
D-FT1081 MAIN PCB AS, VE+NON-VDE, NON-BB, HOT+COLD, 1000RPM
PRPSSWB705
D-FT1081 MAIN PCB AS, VE+VDE, BB, HOT+COLD, 1000RPM
PRPSSWB706
D-FT1081 MAIN PCB AS, VE+VDE, NON-BB, COLD, 1000RPM
PRPSSWB707 D-FT1081 MAIN PCB AS, VE+VDE, BB, COLD, 1000RPM
F08 PCB AS PRPSSWB708
D-FT1081 MAIN PCB AS, VE+VDE, NON-BB, HOT+COLD, 1000RPM
1
PRPSSWB710 D-FT1281 MAIN PCB AS, VE+NON-VDE, BB, HOT+COLD, 1200RPM
PRPSSWB711 D-FT1281 MAIN PCB AS, VE+NON-VDE, NON-BB, COLD, 1200RPM
PRPSSWB712 D-FT1281 MAIN PCB AS, VE+NON-VDE, BB, COLD, 1200RPM
PRPSSWB713 D-FT1281 MAIN PCB AS, VE+NON-VDE, NON-BB, HOT+COLD, 1200RPM
PRPSSWB715 D-FT1281 MAIN PCB AS, VE+VDE, BB, HOT+COLD, 1200RPM
PRPSSWB716
D-FT1281 MAIN PCB AS, VE+VDE, NON-BB, COLD, 1200RPM
PRPSSWB717 D-FT1281 MAIN PCB AS, VE+VDE, BB, COLD, 1200RPM
PRPSSWB718 D-FT1281 MAIN PCB AS, VE+VDE, NON-BB, HOT+COLD, 1200RPM
No. PART NAME PART CODE SPECIFICATION Q'TY REMARK
8th PANEL
DWD-FT128X
SERIES
8th PANEL
DWD-FT108X
SERIES

17
EXPLODE VIEW AND PARTS LIST
■ CABINET FRONT AS
C01 CABINET FRONT 3610811210 PCM, SGCC 0.8T, SILVER 1 DWD-F1XX3
3610811220 SECD 0.7T DWD-F1XX1(2)
C02 SWITCH DOOR LOCK 3619047100 DL-LC.BITRON_3P.250V16A.BI-METAL 1
C03 SCREW TAPPING 7122401208 T2S TRS 4X12 SUS 2
C04 PLATE HINGE SUPPORT 3614531900 SGCC T1.6 0 No use
C05 HINGE DOOR 3612902800 ALDC 1
C06 CAP HINGE DOOR 3610916500 POM 2
C07 SCREW TAPPING 3616030000 F/L BOLT(SE) 5*12 SUS 2
C08 SCREW TAPPING 3616029950 TTS"S" HEX F/L 4*8 6
C09 CLAMP DOOR AS 3611204810 HSW3, D=1.4 GS 1
C10 FRAME DOOR I 3612205200 PP 1
C11 HANDLE DOOR 3612608600 ABS 1
C12 PIN HANDLE 3618200200 SUS304, D3, L48 1
C13 SPRING HOOK 3615114600 SUS D1.4 1
C14 HOOK DOOR 3613100700 ZNDC 1
C15 DOOR GLASS 361A110700 GLASS PI300 1
C16 FRAME DOOR O 3612205102 HIPS D-F'S 1 DWD-F1XX1
3612205120 CR3 DWD-F1XX2(3)
C17 SCREW TAPPING 7115402008 T1S FLT 4*20 SUS 6
No. PART NAME PART CODE SPECIFICATION Q'TY REMARK

18
EXPLODE VIEW AND PARTS LIST
■ TUB ASS’Y

19
EXPLODE VIEW AND PARTS LIST
T01 BALANCER WEIGHT F AS 3616111800 D-FT1081's, 8kg 1
T02 SPECIAL SCREW 3616029400 SWCH 8.5X30 6
T03 GASKET 3612327300 EPDM, D-FT1081 1
T04 CLAMP GASKET AS 3611204520 HSW3, GS 1
T05 TUB *F 3618831000 FRPP, FT1081 1
T06 SPECIAL SCREW 3616062700 SWRCH 18A 5.6X30 12
T07 DAMPER FRICTION 361A700140 70N CIMA ST=170-260 DL=202 1
T08 DAMPER FRICTION 361A700140 70N CIMA ST=170-260 DL=202 1
T09 DAMPER PIN 361A700200 AKS D=14.5 2
T10 SPRING SUSPENSION *L 3615118700 FU1081,D=3.2 L=173,K=0.664 YELLOW COATING 1
T11 SPRING SUSPENSION *R 3615118750 FU1081,D=3.2 L=167,K=0.455 SILVER COATING 1
T12 HOSE VENT 3613267100 EPDM 1
T13 CLAMP HOSE 3611204700 D26 1
T14 HOSE DRAIN 3613267300 EPDM 1
T15 AIR TRAP 361A500101 PP 1
T16 HOSE AIR 3613268600 ID=4,OD=8, L=580 1
T17 CLAMP AS 3611203210 ID=61, WIRE+GUIDE+BOLT, GS 1
T18 CLAMP HOSE 3611201401 HSW3,YW,D2.6,ID36,W44.5 1
T19 CLAMP HOSE 3611204700 D26 1
T20 DRUM SUB AS 3617004002 D-F 0.4T(CENTER, REAR), 0.5(FRONT) 1
T21 LIFTER WASH 361A400410 PP D-F'S NANO 3
T22 SPIDER AS 361A301500 D-FT1081 1
T23 SPECIAL SCREW 3616029500 SUS430 8*25 3
T24 WATER SEAL 361A600100 NBR 1
T25 BEARING INNER 3616303100 F,L,E,U,6206Z 1
T26 BEARING HOUSING 3616305600 ALDC, FT1081 1
T27 BEARING OUTER 3616303200 F,L,E,U,6205Z 1
T28 TUB REAR 3618831100 FRPP, FT1081 1
T29 SEALING TUB 3612321601 EPDM L1600(-0~ +10) 1
T30 FIXTURE HEATER 3612007300 SUS 0.7T 440X45 1
T31 SCREW TAPPING 7122401408 T2S TRS 4*14 SUS,STS 2
T32 HEATER WASH 3612803600 230V 2000W.1R5A721001.IRCA FUSE 2EA 1
3612803700 230V 2000W.1R5A721002.IRCA FUSE 2EA 1
3612803800 240V 2000W.1R5A721003.IRCA FUSE 2EA 1
3612802400 220V 2KW.1R0A721001.RW8TF.IRCA 1
3612802420 240V 2KW.1R0A721003.RW8TF.IRCA 1
T33 THERMISTOR WASH 361AAAAB10 R25=1.704_ R80=11.981_ 1
T34
UNIT MOTOR UNIVERSAL 36189L4H30 DC220V 50HZ 2P PI340 45T DUM-66 TONLON 1
36189L4H10 AC220~240/50 G&J GJ-2UA005A 2P PI340 45T(CCA) 1option
36189L4H20 DC220/50 C&M 2P PI340 45T(AL) 1 option
T35 SPECIAL SCREW 3616007400 T2S TRS 4X10+24 2
T36 UNIT BUBBLE PUMP AS 36189L4120 220-240V DBK-240DB RP CHSHION 1
T37 PULLEY 3618433200 ALDC, D-FU
T38 BELT V 3616591110 GATES 4PJ1120 BUTADIENE RUBBER 1
T39 SPECIAL BOLT AS 3616029600 SWCH 10*30,F/L BOLT S.P/W SEAL LOCK 1
T40 BALANCER WEIGHT *T AS 3616110700 PP, D-LU1011, 2.48KG 1
No. PART NAME PART CODE SPECIFICATION Q'TY REMARK
1 piece
SVC part
CE, CB
Standard