Dahua Technology D-SDZ4032-HNR-ZB User manual

Network Speed Dome & PTZ Camera
Installation Manual
V1.0.0

I
Foreword
General
This manual introduces the precautions, installation preparations and cables of the Speed Dome &
PTZ Camera (hereinafter referred to as "the Device").
Some specifications and metrics might not apply to all models, and the actual product shall prevail.
Safety Instructions
The following categorized signal words with defined meaning might appear in the manual.
Signal Words Meaning
Indicates a high potential hazard which, if not avoided, will result in
death or serious injury.
Indicates a medium or low potential hazard which, if not avoided,
could result in slight or moderate injury.
Indicates a potential risk which, if not avoided, could result in property
damage, data loss, lower performance, or unpredictable result.
Provides methods to help you solve a problem or save you time.
Provides additional information as the emphasis and supplement to
the text.
Revision History
Version Revision Content Release Time
V1.0.0 First release. July 2020
About the Manual
●The manual is for reference only. If there is inconsistency between the manual and the actual
product, the actual product shall prevail.
●We are not liable for any loss caused by the operations that do not comply with the manual.
●The manual would be updated according to the latest laws and regulations of related regions.
For detailed information, see the paper manual, CD-ROM, QR code or our official website. If there
is inconsistency between paper manual and the electronic version, the electronic version shall
prevail.
●All the designs and software are subject to change without prior written notice. The product
updates might cause some differences between the actual product and the manual. Please
contact the customer service for the latest program and supplementary documentation.
●There still might be deviation in technical data, functions and operations description, or errors in
print. If there is any doubt or dispute, please refer to our final explanation.
●Upgrade the reader software or try other mainstream reader software if the manual (in PDF
format) cannot be opened.
●All trademarks, registered trademarks and the company names in the manual are the properties

II
of their respective owners.
●Please visit our website, contact the supplier or customer service if there is any problem occurred
when using the Camera.
●If there is any uncertainty or controversy, please refer to our final explanation.

III
Important Safeguards and Warnings
The manual will help you to use the Device properly. Read the manual carefully before using the
Device, and keep it well for future reference.
Operating Requirements
●Do not press hard, violently vibrate, and soak the Device when transporting and storing it.
Complete package is necessary during the transportation. We will assume no responsibility for
any damage or problem caused by incomplete package during the transportation.
●Protect the Device from falling down or heavy vibration.
●Buckle the safety hook before installing the Device if it is included.
●Keep the Device away from devices that generate electromagnetic field like televisions, radio
transmitters, electromagnetic devices, electric machines, transformers, and speakers; otherwise
image quality will be influenced.
●Keep the Device away from smoke, vapor, heat, and dust.
●Do not install the Device near heating furnace, spotlight, and other heat sources. If it is installed
on ceiling, in kitchen or near boiler room, the Device temperature might rise.
●Do not dissemble the Device; otherwise it might cause dangers or device damage. Contact your
local retailer or customer service center for internal setup or maintenance requirement.
●Make sure that there is no metal, or inflammable, explosive substance in the Device; otherwise it
might cause fire, short-circuit, or other damage.
●Avoid sea water or rain eroding the Device.
●Avoid the lens aiming at intense light source, including sunlight and incandescent light;
otherwise the lens might be damaged.
●It is recommended to use the Device with a lightning-proof device for better lightning-proof
effect.
●Before installing the Device, you need to confirm the salt spray tolerance level. Do not install the
Device in an environment with higher salt spray level than the Device can tolerate. There are
three salt spray tolerance levels of cameras.
◇Devices with higher salt spray tolerance level can be installed in an area within 1500 m by the
sea, or offshore platform.
◇Devices with medium salt spray tolerance level can be installed in an area 1500 m away from
the sea.
◇Devices not salt spray tolerant can only be installed in an area 3000 m away from the sea.
●After unpacking, if the packing bag is damaged or leaking air, and the desiccant particles are of
different colors, the normal use of the Device will not be affected.
●For the Device that supports laser, do not aim the laser directly at eyes. And keep a proper
distance from the flammable to avoid fire.
●Contact your local retailer or customer service center if the Device is abnormal. Do not
disassemble or repair the product by yourself. We will assume no responsibility for any problems
caused by unauthorized modifications, disassembly or repair, incorrect installation or use, and
overuse of certain components.

IV
Power Requirements
●All installation and operations shall conform to local electrical safety regulations.
●Turn off the power and disconnect the power cord immediately if there is water or liquid falling
into the Device. And contact your local retailer or customer service center.
●The power source shall conform to the requirement of the Safety Extra Low Voltage (SELV)
standard, and supply power with rated voltage which conforms to Limited Power Source
requirement according to IEC60950-1. Note that the power supply requirement is subject to the
device label.
●Use the power adapter provided by legitimate manufacturers.
●Do not connect several cameras to one power adapter. It may result in overheat or fire if it
exceeds the rated load.
●Make sure that the power is off when you connect the cables, and install or uninstall the Device.
●Turn off the power and disconnect the power cord immediately if there is any smoke, disgusting
smell, or noise from the Device. And contact your local retailer or customer service center.
Cleaning Requirements
●Clean the enclosure with soft cloth. To remove the dirt, you can dip the soft cloth in proper
detergent, wring the soft cloth out, and then dry the enclosure with soft cloth.
●Do not use gasoline, paint thinner or other chemicals to clean the enclosure; otherwise it might
result in enclosure transfiguration or paint flake.
●Read all the manuals included before using chemical cloth. Avoid long time touch between the
plastic or rubber material and the enclosure. It might result in device damage and paint flake.
Requirements for Installation and maintenance personnel
●Have certificates or experiences related to installation and maintenance of the closed-circuit
television (CCTV).
●Have certificates related to working at height.
●Have basic knowledge and operation technique for low-voltage wiring and low-voltage
electronic circuit connection.
●Have the ability to read and understand the manual.
Requirements for Lifting the Device
●Select appropriate tools to lift the Device.
●Make sure that the selected tools reach the installation height.
●Make sure that the selected tools have high safety performance.

V
Table of Contents
Foreword ........................................................................................................................................................................................................I
Important Safeguards and Warnings............................................................................................................................................ III
1 Installation Preparation.................................................................................................................................................................... 1
1.1 Basic Requirements .................................................................................................................................................................. 1
1.2 Installation Check...................................................................................................................................................................... 1
1.3 Cable Preparation...................................................................................................................................................................... 1
1.3.1 Video Cable Requirements ........................................................................................................................................ 1
1.3.2 RS-485 Cable Requirements...................................................................................................................................... 2
1.3.3 Selecting Power Cable.................................................................................................................................................. 2
1.3.3.1 Power Cable............................................................................................................................................................ 2
1.3.3.2 PoE Power Cable................................................................................................................................................... 3
2 Cables ......................................................................................................................................................................................................... 4
2.1 Cable Description ...................................................................................................................................................................... 4
2.2 Cable Connection....................................................................................................................................................................... 6
2.2.1 Alarm Cable Connection.............................................................................................................................................. 6
2.2.2 Thunder-Proof Cable Connection........................................................................................................................... 6
2.2.2.1 Outdoor .................................................................................................................................................................... 6
2.2.2.2 Indoor ........................................................................................................................................................................ 8
3 RS-485 Cable.........................................................................................................................................................................................10
3.1 Basic Features............................................................................................................................................................................10
3.2 Common Issues in Use...........................................................................................................................................................10
3.3 FAQ on RS-485 Cable .............................................................................................................................................................11
4 Wi-Fi Performance..............................................................................................................................................................................12
5 Cable Diameter (24V AC) and Transmission Distance......................................................................................................13
6 Cable Diameter (12V DC) and Transmission Distance......................................................................................................14
7 Cable Diameter (24V DC) and Transmission Distance......................................................................................................15
8 Cable Diameter (30V DC) and Transmission Distance......................................................................................................16
9 Cable Diameter (36V DC) and Transmission Distance......................................................................................................18
10 Wire Gauge Reference Sheet......................................................................................................................................................20
Appendix 1 Cybersecurity Recommendations........................................................................................................................21

1
1 Installation Preparation
1.1 Basic Requirements
●All installation and operations shall conform to your local electrical safety regulations, fire
protection regulations, and other relevant regulations.
●Make sure that the application scenario conforms to installation requirements. Contact your local
retailer or customer service center if there is any problem.
●Use the Device according to the operating environment.
●Keep the original packing material well because you might need it to pack the Device and send it
back for repair.
1.2 Installation Check
●Make sure that the place where the Device is installed has enough space to hold the Device and
its mounting accessories.
●For PTZ cameras, make sure that the place where the Device is installed can sustain at least 4
times the weight of the Device and its mounting accessories; for speed domes, make sure that
the ceiling and wall can sustain 8 times the weight of the Device and its mounting accessories.
●Do not install the Device at risky or unstable places.
●Make sure that the wall is thick enough to install expansion bolts (Users need to buy expansion
bolts separately).
●For speed domes support intelligent tracking, illegal parking capture or laser, make sure that the
mounting height is over 6 m.
1.3 Cable Preparation
Select the video cable depending on transmission distance.
1.3.1 Video Cable Requirements
●75 ohm.
●Pure copper cored cables.
●95% braided copper shielding.
●For cables applicable to network devices and their maximum transmission distance, see Table
1-1.
●For cables applicable to HDCVI devices and their maximum transmission distance, see Table 1-2.

2
Table 1-1 Cables and maximum transmission distance (network)
Model Maximum Transmission Distance (ft/m)
RG59/U 750 ft/229 m
RG6/U 1,000 ft/305 m
RG11/U 1,500 ft/457 m
Table 1-2 Cables and maximum transmission distance (HDCVI)
Model Maximum Transmission Distance (ft/m)
SYV-75-3
720P (25 fps/30 fps): 1,640 ft/500 m
720P (50 fps/60 fps): 984 ft/300 m
1080P (25 fps/30 fps): 984 ft/300 m
1.3.2 RS-485 Cable Requirements
When using 0.56 mm (24AWG) twisted-pair line, depending on different baud rates, the theoretical
maximum transmission distance is different.
Table 1-3 Theoretical maximum transmission distance
Baud Rate Maximum Transmission Distance
2400bps 1800 m
4800bps 1200 m
9600bps 800 m
The maximum transmission distance will be reduced in the following conditions: When thinner
communication cables are used; the Device is used in places with intense electromagnetic
interference; too many devices are connected to the RS-485 cable. Otherwise, maximum
transmission distance will be increased.
1.3.3 Selecting Power Cable
1.3.3.1 Power Cable
Depending on the power cable specification, the same cable diameter corresponds to different
transmission distance.
●For 24V AC power supply, see "5 Cable Diameter (24V AC) and Transmission Distance".
●For 12V DC power supply, see "6 Cable Diameter (12V DC) and Transmission Distance".
●For 24V DC power supply, see "7 Cable Diameter (24V DC) and Transmission Distance".
●For 30V DC power supply, see "8 Cable Diameter (30V DC) and Transmission Distance".
●For 36V DC power supply, see "9 Cable Diameter (36V DC) and Transmission Distance".

3
1.3.3.2 PoE Power Cable
Table 1-4 PoE power cable
POE Specification Network Cable Specification
AF
CAT5E and network cables with higher standard.
AT
HiPoE or BT

4
2 Cables
2.1 Cable Description
The Device is equipped with a multi-functional combination cable by default, including power cord,
video cable, audio cable, RS-485 control cable, alarm cable, network cable, and optical fiber cable.
For details, see Figure 2-1.

5
The cables of different models vary, and the actual product shall prevail. The manual will introduce
the cables as complete as possible.
Figure 2-1 Cables
Table 2-1 Cable description
No. Description
1 FC connector
2 DC power input port
3
24V AC power input
●Red: V+
●Black: V–
●Yellow-green: Grounding cable
4
RS-485
●Yellow: A+
●Orange: B–

6
No. Description
5 Video output port
6 Ethernet port
7
●White: Audio input
●Red: Audio output
●Black: Audio grounding cable
8
●Blue: Alarm output 1
●Black: Alarm output 2
●Green: Contact switch 1
●Pink: Contact switch 2
●Yellow-green: Grounding cable
9
●Red: Alarm input 1
●Brown: Alarm input 2
●Grey: Alarm input 3
●Light green: Alarm input 4
●Purple: Alarm input 5
●White: Alarm input 6
●Yellow-black: Alarm input 7
2.2 Cable Connection
2.2.1 Alarm Cable Connection
Step 1 Connect the alarm input device to ALARM_IN and ALARM_GND of the user cable.
Step 2 Connect alarm output device to ALARM_OUT and ALARM_COM of the user cable, and
alarm output is relay switch output.
Step 3 Go to the web interface of the Device, and complete settings for alarm input and output
devices. The alarm input on Web interface corresponds to the alarm input of the cables. Set
the corresponding NO and NC output according to the high/low level signal generated by
alarm input device when alarm is triggered.
Step 4 Set the alarm output of cables on the web interface.
2.2.2 Thunder-Proof Cable Connection
The following installation figures are for reference only, and the actual product shall prevail. This
chapter takes PTZ camera as an example.
2.2.2.1 Outdoor
Transient voltage suppressor (TVS) is applied to protect the Device against voltage spikes and
overvoltage below 6000V. However, it is still necessary to do operations to protect the Device

7
according to actual conditions.
●The signal transmission cable must stay at least 50 m away from high voltage devices and high
voltage wires.
●When laying cables outdoors, try to lay them under the eaves.
●At open places, lay cables underground by means of hermetic steel tube, and then do
equipotential grounding to both ends of steel tubes. Laying overhead power cables are
prohibited.
●At places with severe thunderstorms and induced voltage (like substation), you need to prepare
high-powered lightning protection devices and lightning conductors.
●When laying cables and connecting lightning protection devices, you must comply with regional
laws and regulations.
●You must do equipotential grounding to the electric system. The grounding device must meet
the requirements of anti-jamming and conform to your local electrical safety code. The
grounding device shall not form short circuit to N (neutral) line of high voltage power grid or be
mixed with other wires. When the electrical system is connected to the ground cable, the
impedance cannot exceed 4Ω and the cross-sectional area of the earth lead cannot exceed 25
mm2.
Figure 2-2 Installing lightning protection devices outdoors
Table 2-2 Installing lightning protection devices outdoors
No. Description
1 Video lightning conductor.
2 Communication lightning conductor.
3 Power supply lighting conductor.
4 Impedance of the cable connected to the grounding wire should be less than 4Ω.
5 The radius is 60 m.
6 Lightning conductor.
7 Steel tube.

8
Figure 2-3 Installing lightning protection devices outdoors (2)
●R: The radius of the circle, and R=60 m.
●L1: The length of the pole that holds the lightning conductor.
●L2: The length of the rail that holds the Device.
●H: The length of the lightning conductor.
To get the value of L1, you need to use the formula:
2.2.2.2 Indoor
You shall use multiple copper cables whose cross-sectional area is not less than 25 mm2to connect
the yellow-green grounding cable/grounding screws to the indoor equipotential grounding
terminals.

9
Figure 2-4 Installing lightning protection devices indoors
Table 2-3 Installing lightning protection devices indoors
No. Name
1 Yellow-green grounding cable
2 Indoor equipotential grounding terminal

10
3 RS-485 Cable
3.1 Basic Features
RS-485 industrial buses are half-duplex communication buses whose characteristic impedance is
120Ω. Its maximum load is 32 payloads (including controller devices and controlled devices).
3.2 Common Issues in Use
Users tend to connect devices as the way displayed in Figure 3-1. In this case, the terminal resistance
must be connected to the two devices whose cable length is the longest among all the devices (in
Figure 3-1, cable length between 1# and 15# is the longest). However, this connection manner does
not comply with the RS-485 industrial standard. As a result, common issues like signal reflection and
anti-interference capability reduction will occur. And the Device is out of control or cannot stop.
Figure 3-1 Common method to connect devices
To fix the issues, it is recommended to use RS-485 distributors. The RS-485 distributor can help avoid
the common connection issues so as to improve transmission quality.

11
Figure 3-2 Connecting method with RS-485 distributors
3.3 FAQ on RS-485 Cable
Malfunction Possible Reason Solution
The Device can perform
self-check, but is out of
control.
Baud rate/address of the host
and Device are not matched.
Modify the baud rate/address
of the host or Device to be
matched.
Positive electrode and
negative electrode of RS-485
cable are misconnected.
Connect cables to the positive
electrode and negative
electrode correctly.
Loose connection. Connect the cables firmly.
RS-485 cable is broken. Replace RS-485 cable.
The Device can be controlled,
but the operation is not
smooth.
RS-485 cable is in poor
contact.
Connect the RS-485 cable
firmly.
RS-485 cable is broken. Replace RS-485 cable.
The distance between the
host and the Device is too
long.
Install terminal resistance.
Too many cameras are
connected parallelly. Install RS-485 distributors.

12
4 Wi-Fi Performance
Table 4-1 Wi-Fi performance description
Performance Description
Frequency band supported 2.4G; 5G
Working channel (consistent
with AP)
2.4G CH1–CH13 (the actual working
channel shall prevail).
5G The actual working channel shall
prevail.
Transmission performance
●At open places without interference, if the Device is
installed at least 1.5 m above the ground, the effective
communication distance is 100 m.
●In the environment without interference, the signal can
pass through a load-bearing wall, and the effective
communication distance is 20 m.
The actual wall penetration capacity is greatly affected by
network layout and actual environment.

13
5 Cable Diameter (24V AC) and Transmission
Distance
The recommended transmission distances are for reference only, and the actual conditions shall
prevail. The following table shows the maximum transmission distance of cables with certain
diameter when the 24V AC power source voltage loss rate is below 10%.
For devices powered by alternating current, the maximum voltage loss rate allowed is 10%. For
example, when a device of 20W rated power is installed 122 feet (37 m) away from the transformer,
the minimum diameter needed is 0.80 mm.
In the following table, the unit for diameter is mm, and the unit for transmission distance is foot (m).
Table 5-1 Cable diameter (24V AC) and transmission distance
Transmission
Power (W)
Transmission
Distance
(Diameter:
0.80)
Transmission
Distance
(Diameter:
1.00)
Transmission
Distance
(Diameter:
1.25)
Transmission
Distance
(Diameter:
2.00)
5 489 (149) 763 (233) 1193 (364) 3053 (931)
10 244 (74) 382 (116) 596 (182) 1527 (465)
15 163 (50) 254 (77) 398 (121) 1018 (310)
20 122 (37) 191 (58) 298 (91) 763 (233)
25 98 (30) 152 (47) 239 (73) 611 (186)
30 81 (25) 127 (39) 199 (61) 509 (155)
35 70 (21) 109 (33) 170 (52) 436 (133)
40 61 (19) 95 (29) 149 (45) 382 (116)
45 54 (16) 85 (26) 133 (41) 339 (103)
50 49 (15) 76 (23) 119 (36) 305 (93)
55 44 (13) 69 (21) 108 (33) 278 (85)
60 41 (12) 64 (20) 99 (30) 254 (77)
65 38 (12) 59 (18) 92 (28) 235 (72)
70 35 (11) 55 (17) 85 (26) 218 (66)
75 32 (10) 51 (16) 80 (24) 204 (62)
80 31 (9) 48 (15) 75 (23) 191 (58)
85 29 (9) 45 (14) 70 (21) 180 (55)
90 27 (8) 42 (13) 66 (20) 170 (52)
95 26 (8) 40 (12) 63 (19) 161 (49)
100 24 (7) 38 (12) 59 (18) 153 (47)

14
6 Cable Diameter (12V DC) and Transmission
Distance
The recommended transmission distances are for reference only, and the actual conditions shall
prevail. The following table shows the maximum transmission distance of cables with certain
diameter when the 12V DC power source voltage loss rate is below 10%.
For devices powered by direct current, the maximum voltage loss rate allowed is 10%. The cables
mentioned in the following table are all copper cables with electrical resistivity
.
In the following table, the unit for diameter is mm, and the unit for transmission distance is foot (m).
Table 6-1 Cable diameter (12V DC) and transmission distance
Transmission
Power (W)
Transmission
Distance
(Diameter:
0.80)
Transmission
Distance
(Diameter:
1.00)
Transmission
Distance
(Diameter:
1.25)
Transmission
Distance
(Diameter:
2.00)
5 122 (37) 191 (58) 298 (91) 763 (233)
10 61 (19) 95 (29) 149 (45) 382 (116)
15 41 (12) 64 (20) 99 (30) 254 (77)
20 31 (9) 48 (15) 75 (23) 191 (58)
25 24 (7) 38 (12) 59 (18) 153 (47)
30 20 (6) 32 (10) 50 (15) 127 (39)
35 17 (5) 27 (8) 43 (13) 109 (33)
40 15 (5) 23 (7) 37 (11) 95 (29)
45 14 (4) 21 (6) 33 (10) 85 (26)
50 12 (4) 19 (6) 30 (9) 76 (23)
55 11 (3) 17 (5) 27 (8) 69 (21)
60 10 (3) 16 (5) 25 (8) 64 (20)
65 9 (3) 15 (5) 23 (7) 59 (18)
70 9 (3) 14 (4) 21 (6) 55 (17)
75 8 (2) 13 (4) 20 (6) 51 (16)
80 8 (2) 12 (4) 19 (6) 48 (15)
85 7 (2) 11 (3) 18 (5) 45 (14)
90 7 (2) 11 (3) 17 (5) 42 (13)
95 6 (2) 10 (3) 16 (5) 40 (12)
100 6 (2) 10 (3) 15 (5) 38 (12)