Dahua Technology DH-IPC-HDW3441TP-ZS-S2 User manual

Eyeball Network Camera
Quick Start Guide
V1.0.
2ZHEJIANG DAHUA VISION TECHNOLOGY CO., LTD.

Quick Start Guide
I
Foreword
General
This manual introduces the functions, installation, and operations of the camera.
Safety Instructions
The following categorized signal words with defined meaning might appear in the manual.
Signal Words Meaning
WARNING
Indicates a medium or low potential hazard which, if not avoided,
could result in slight or moderate injury.
CAUTION
Indicates a potential risk which, if not avoided, could result in
property damage, data loss, lower performance, or unpredictable
result.
NOTE Provides additional information as a supplement to the text.
Revision History
Version Revision Content Release Date
V1.0.2 Updated SD card installation. November 2021
V1.0.1 Updated "Important Safeguards and Warnings." April 2021
V1.0.0 First release. May 2019
Privacy Protection Notice
As the device user or data controller, you might collect the personal data of others such as their face,
fingerprints, and license plate number. You need to be in compliance with your local privacy protection
laws and regulations to protect the legitimate rights and interests of other people by implementing
measures which include but are not limited: Providing clear and visible identification to inform people
of the existence of the surveillance area and provide required contact information.
About the Manual
The manual is for reference only. Slight differences might be found between the manual and the
product.
We are not liable for any loss caused by the operations that do not comply with the manual.
The manual will be updated according to the latest laws and regulations of related jurisdictions.
For detailed information, see the paper User Manual, use our CD-ROM, scan the QR code or visit
our official website. The manual is for reference only. Slight differences might be found between
the electronic version and the paper version.

Quick Start Guide
II
All the designs and software are subject to change without prior written notice. The product
updates might cause some differences between the actual product and the manual. Please
contact the customer service for the latest program and supplementary documentation.
There still might be deviation in technical data, functions and operations description, or errors in
print. If there is any doubt or dispute, please refer to our final explanation.
Upgrade the reader software or try other mainstream reader software if the manual (in PDF
format) cannot be opened.
All trademarks, registered trademarks and the company names in the manual are the properties
of their respective owners.
Please visit our website, contact the supplier or customer service if there is any problem occurred
when using the device.
If there is any uncertainty or controversy, please refer to our final explanation.

Quick Start Guide
III
Important Safeguards and Warnings
Electrical Safety
All installation and operation should conform to your local electrical safety codes.
The power supply must conform to the requirements of ES1 in IEC 62368-1 standard and be no
higher than PS2. Note that the power supply requirements are subject to the device label.
Make sure the power supply is correct before operating the device.
A readily accessible disconnect device shall be incorporated in the building installation wiring.
Prevent the power cable from being trampled or pressed, especially the plug, power socket and
the junction extruded from the device.
Environment
Do not aim the device at strong light to focus, such as lamp light and sun light; otherwise it might
cause over brightness or light marks, which are not the device malfunction, and affect the
longevity of Complementary Metal-Oxide Semiconductor (CMOS).
Do not place the device in a damp or dusty environment, extremely hot or cold temperatures, or
the locations with strong electromagnetic radiation or unstable lighting.
Keep the device away from any liquid to avoid damage to the internal components.
Keep the indoor device away from rain or damp to avoid fire or lightning.
Keep sound ventilation to avoid heat accumulation.
Transport, use and store the device within the range of allowed humidity and temperature.
Heavy stress, violent vibration or water splash are not allowed during transportation, storage and
installation.
Pack the device with standard factory packaging or the equivalent material when transporting
the device.
Install the device in the location where only the professional staff with relevant knowledge of
safety guards and warnings can access. The accidental injury might happen to the non-
professionals who enter the installation area when the device is operating normally.
Operation and Daily Maintenance
Do not touch the heat dissipation component of the device to avoid scald.
Carefully follow the instructions in the manual when performing any disassembly operation
about the device; otherwise, it might cause water leakage or poor image quality due to
unprofessional disassembly. Please make sure that the gasket ring is flat and properly installed in
the groove before installing the cover. Please contact after-sale service for desiccant replacement
if there is condensed fog on the lens after unpacking or when the desiccant turns green (Not all
models are included with the desiccant).
We recommend using the device together with lightning arrester to improve lightning protection
effect.
We recommend grounding the device to enhance reliability.

Quick Start Guide
IV
Do not touch the image sensor (CMOS) directly. Dust and dirt could be removed with air blower,
or you can wipe the lens gently with soft cloth that moistened with alcohol.
You can clean the device body with soft dry cloth, and for stubborn stains, use the cloth with mild
detergent. To avoid possible damage on device body coating which could cause performance
decrease, do not use volatile solvent such as alcohol, benzene, diluent to clean the device body,
nor can strong, abrasive detergent be used.
Dome cover is an optical component. Do not touch or wipe the cover with your hands directly
during installation or operation. For removing dust, grease or fingerprints, wipe gently with
moistened oil-free cotton with diethyl or moistened soft cloth. You can also remove dust with an
air blower.
WARNING
Strengthen the protection of network, device data and personal information by adopting
measures which include but not limited to using strong password, changing password regularly,
upgrading firmware to the latest version, and isolating computer network. For some devices with
old firmware versions, the ONVIF password will not be changed automatically along with
changing the system password, and you need to upgrade the firmware or manually change the
ONVIF password.
Use standard components or accessories provided by manufacturer and make sure the device is
installed and maintained by professional engineers.
Do not expose the surface of the image sensor to laser beam radiation in an environment where
a laser beam device is used.
Do not provide two or more power supply sources for the device unless otherwise specified. A
failure to follow this instruction might cause damage to the device.

Quick Start Guide
V
Table of Contents
Foreword............................................................................................................................................................ I
Important Safeguards and Warnings............................................................................................................. III
1 Introduction................................................................................................................................................... 1
2 Network Configuration ................................................................................................................................. 2
Initializing Device....................................................................................................................................................................... 2
Changing Device IP Address.................................................................................................................................................. 4
Logging in to Web Page........................................................................................................................................................... 5
3 Installation..................................................................................................................................................... 6
Packing List................................................................................................................................................................................... 6
Dimension..................................................................................................................................................................................... 6
Installing Device ......................................................................................................................................................................... 7
3.3.1 Installation Type ............................................................................................................................................................ 7
3.3.2 Detaching the Enclosure............................................................................................................................................ 7
3.3.3 Installing SD Card (Optional).................................................................................................................................... 7
3.3.4 Attaching Device........................................................................................................................................................... 8
3.3.5 Installing Waterproof Connector (Optional)....................................................................................................... 9
3.3.6 Adjusting Lens Angle ................................................................................................................................................10

Quick Start Guide
1
1Introduction
Waterproof all the cable joints with insulating tape and waterproof tape to avoid short circuit and
water damage. For the detailed operation, see FAQ manual.
Cables
Table 1-1 Cable information
No. Port Name Description
1 Ethernet port
Connects to network with network cable.
Provides power to the device with PoE.
PoE is available on select models.
2 Power input
Inputs 12 VDC power. Please be sure to supply power as instructed in the
Guide.
Device abnormity or damage could occur if power is not supplied correctly.

Quick Start Guide
2
2Network Configuration
Device initialization and IP address setting can be finished with the ConfigTool or in web interface. For
more information, see web operation manual.
Device initialization is available on select models, and it is required at first use or after the device
being reset.
Device initialization is available only when the IP addresses of the device (192.168.1.108 by
default) and the PC stay on the same network segment.
Plan useable network segment properly to connect the device to the network.
The following figures and interfaces are for reference only.
Initializing Device
Double-click ConfigTool.exe to open the tool.
Click .
Click Search Setting.
Setting
Select the searching way.
Current Segment Search (default)
Select the Current Segment Search checkbox. Enter the username in the Username
box and the password in the Password box. The system will search devices accordingly.
Other Segment Search
Select the Other Segment Search checkbox. Enter IP address in the Start IP box and
End IP box respectively. Enter user name and password. The system will search for the
devices accordingly.
If you select the Current Segment Search checkbox and the Other Segment Search
checkbox together, the system searches for devices under both conditions.

Quick Start Guide
3
Enter username and the password when you want to change IP, configure the system,
update the device, restart the device, and more.
Click OK.
Select one or several devices in uninitialized status, and then click Initialize.
Select the devices to be initialized, and then click Initialize.
If you do not provide the linked information for password reset, you can reset the
password only through XML file.
When initializing multiple devices, ConfigTool initializes all devices based on the
password reset mode of the first selected device.
Password setting
Set and confirm the password of the devices, enter a valid email address, and then click Next.

Quick Start Guide
4
Device initialization
Select Easy4ip or select Auto-check for updates as needed. If neither, leave them unselected.
Click OK to initialize the device.
Click the success icon ( ) or the failure icon ( ) for the details.
Click Finish.
Changing Device IP Address
You can change IP address of one or multiple devices in one time. This section is based on
changing IP addresses in batches.
Changing IP addresses in batches is available only when the corresponding devices have the
same login password.
Follow "Step 1" to "Step 4" in "2.1 Initializing Device" to search devices on your network
segment.
After clicking Search setting, enter the username and password, and please make sure they
are the same as what you set during initialization, otherwise there will be wrong password
notice.
Select the devices whose IP addresses need to be changed, and then click Batch Modify IP.