Dahua DH-IPC-GX6 User manual

Dahua Bullet Wi-Fi Camera Quick Start Guide
Dahua Bullet Wi-Fi Camera
Quick Start Guide
Version 1.0.0
ZHEJIANG DAHUA VISION TECHNOLOGY CO., LTD.

Dahua Bullet Wi-Fi Camera Quick Start Guide
2
1 Packing List
Device ×1
QSG ×1Screw Package ×1
Power Adapter ×1
Waterproof Connector×1

Dahua Bullet Wi-Fi Camera Quick Start Guide
3
2 Product Appearance
Please refer to Figure 2-1 for device port description.
Figure 2-1
Please refer to the following table for more details about each port.
SN
Name
①
Power port
②
Network port
Table 2-1
Figure 2-2
Please refer to the following table for more details about each component.

Dahua Bullet Wi-Fi Camera Quick Start Guide
4
Table 2-2
Note
For reset, long press for 8 seconds and then the light off; For WPS (Wi-Fi Protected
Setup), one quick press.
Please refer to the following table for more details about status of indicator light.
Indicator light status
Device status
Red light stably on
Booting
Green light slow flashing
Booting completed, await Wi-Fi config,
enter smart config status;
Green light quick flashing
WPS connecting (The device is trying to
connect to Wi-Fi via WPS).
Green light stably on
Wi-Fi connection succeeded, operate
normally.
Red and green lights flash alternately
Device upgrade
Red light slow flashing
Network disconnection
Red light quick flashing
Device fail to boot up; SD card does not
work
Table 2-3
SN Name
①Lower cover
②SD card slot
③Reset/WPS
④MIC
⑤Indicator light
⑥Antenna

Dahua Bullet Wi-Fi Camera Quick Start Guide
5
3 Operation by Easy4ip App
Step 1 Power on your camera with power adapter.
Step 2 Connect your smartphone to your Wi-Fi network, scan "Easy4ip" QR on the
packing box, download and install "Easy4ip" APP.
Step 3 Open Easy4ip APP (take iOS version as an example), see Figure 3-1. Please
register an account for first use.
Figure 3-1
Step 4 Please tap “+”to add new devices after you login your account.

Dahua Bullet Wi-Fi Camera Quick Start Guide
6
Figure 3-2
Step 5 Scan the QR code on the back of the camera to get the SN, you can also tap
"Manually enter the SN" and manually input the SN number on the next page.
Then tap "Next".

Dahua Bullet Wi-Fi Camera Quick Start Guide
7
Figure 3-3
Step 6 Select “Yes, go to Wi-Fi settings”and make sure your smartphone is
connected to the same Wi-Fi, then tap “Next”.
Figure 3-4
Step 7 Fill in the password of your Wi-Fi, then tap “Next”.

Dahua Bullet Wi-Fi Camera Quick Start Guide
8
Figure 3-5
Step 8 Input your device password, the default password is “admin”.
Figure 3-6
Step 9 Your camera is successfully added. You can set up your time zone and start
preview.

Dahua Bullet Wi-Fi Camera Quick Start Guide
9
Figure 3-7
Note
If you have more cameras, please follow step 4-9 to add them one by one.
If you want to change the Wi-Fi signal, please reset the camera to factory default
and repeat step 4-9 to add the device

Dahua Bullet Wi-Fi Camera Quick Start Guide
10
4 Device Installation
Note
Please make sure the installation surface can min support the 3X weight of the camera
and the bracket.
Figure 4-1
Step 1 Dig holes on the installation surface (wall or ceiling).
Step 2 Open accessories bag, take out expansion bolt and insert it into the hole you
just dug.
Step 3 Open accessories bag, take out self-tapping screws. Tighten the screws to fix
the device on the installation surface (wall or ceiling).
Step 4 Connect external wiring of the device properly.