Dahua HFW2100R-VF User manual

HDCVI IR Vari-focal Waterproof Fixed Camera
User’s Manual
Version 1.0.0

i
Table of Contents
1General Introduction ..................................................................................................................1
1.1 Overview........................................................................................................................1
1.2 Features.........................................................................................................................1
1.3 Functions .......................................................................................................................1
1.4 Specifications................................................................................................................2
2Framework and Dimensions.....................................................................................................4
2.1 Dimensions....................................................................................................................4
2.2 Structure ........................................................................................................................4
2.3 5-Direction Buttons Settings ................................ Błąd! Nie zdefiniowano zakładki.
3Installation............................................................................. Błąd! Nie zdefiniowano zakładki.
4Menu.............................................................................................................................................8
4.1 HDCVI Series DVR Settings.......................................................................................8
4.2 Menu List .......................................................................................................................9
4.3 Note ..............................................................................................................................10
Appendix Toxic or Hazardous Materials or Elements ...............................................................12

ii
Welcome
Thank you for purchasing our HDCVI camera!
This user’s manual is designed to be a reference tool for your system.
Please read the following safeguard and warnings carefully before you use this series product!
Please keep this user’s manual well for future reference!

iii
Important Safeguards and Warnings
1．Electrical safety
All installation and operation here should conform to your local electrical safety codes.
The power shall conform to the requirement in the SELV (Safety Extra Low Voltage) and the Limited
power source is rated 12V DC in the IEC60950-1.
We assume no liability or responsibility for all the fires or electrical shock caused by improper handling
or installation.
2．Transportation security
Heavy stress, violent vibration or water splash are not allowed during transportation, storage and
installation.
3．Installation
Do not apply power to the camera before completing installation.
Please install the proper power cut-off device during the installation connection.
Always follow the instruction guide the manufacturer recommended.
If this product is installed in the ceiling, please make sure the installation position can sustain the min
50N.
4．Qualified engineers needed
All the examination and repair work should be done by the qualified service engineers.
We are not liable for any problems caused by unauthorized modifications or attempted repair.
5．Environment
This series HDCVI camera should be installed in a cool, dry place away from direct sunlight or strong
light, inflammable, explosive substances and etc.
This series camera shall work on the specified working temperature. Please keep it away from the
electromagnetic radiation object and environment.
Please make sure the CMOS component is out of the radiation of the laser beam device. Otherwise it
may result in CMOS optical component damage.
Please keep the sound ventilation.
Do not allow the water and other liquid falling into the camera.
6. Accessories
Be sure to use all the accessories recommended by manufacturer.
Before installation, please open the package and check all the components are included.
Contact your local retailer ASAP if something is broken in your package.
7. Daily Maintenance

iv
Please shut down the device and then unplug the power cable before you begin daily maintenance
work.
Use the dry soft cloth to clean the device. If there is too much dust, please use the water to dilute the
mild detergent first and then use it to clean the device. Finally use the dry cloth to clean the device.
Please put the dustproof cap to protect the CMOS component when you do not use the camera.

v
Applicable model
This manual can be applied to following models:
HAC-HFW2120RP-VF
HAC-HFW2120RN-VF
HAC-HFW2220RP-VF
HAC-HFW2220RN-VF

1
1General Introduction
1.1 Overview
This series megapixel HD camera conforms to the HDCVI standard. It supports video signal
high-speed long distance transmission without any delay. It can be controlled by the DVR
conforming to the HDCVI.
1.2 Features
High-performance CMOS image sensor, megapixel definition.
Support manual adjustment of lens zoom and focus, conduct lens focus and zoom by
opening the lower cover of the camera body, which is convenient to install for clients.
Support HD video and control signal coaxial transmission.
Support 75-3 coaxial cable transmission without any loss. 720P series transmission
distance over 500m, 1080P series transmission distance over 300m.
High speed, long distance real-time transmission.
Support HDCVI HD and analog SD switch output.
720P series support 720P@25, 720P@30, 720P@50, 720P@60.
1080P series support 1080P@25, 1080P@30, 720P@25, 720P@30, 720P@50,
720P@60.
Support high performance 3D noise reduction (denoise), excellent performance in low
illumination
Support ICR switch to realize surveillance both in the daytime and at night.
Support OSD (on-screen display), suitable for user self-defined setup.
Support DC12V power supplying.
IP66 compliance.
Support intelligent IR function, max IR distance 30m.
1.3 Functions
HDCVI Specification
HDCVI（High Definition Composite Video Interface）is an over-coaxial –cable HD video
transmission standard. The technology renders two HD video formats by progressive scanning.
OSD
User-friendly on-screen display for you to select the different functions.
ICR
The IR cut removal is to filter the IR light in the daytime and then auto switch to the general
fitter at night. This function allows the camera to output the high sensitivity and clear video.
Smart IR technology
The sensor controls the IR light on/off via the combination work of the hardware and software,
which realizes the automatically IR light compensation according to the environment
illumination.

2
3D NR
Comparing with the general 2D denoise function, the 3D denoise function can not only denoise
the brightness of the video separation signal and saturation signal, it can also denoise the
original data from CCD. It greatly enhances noise reduction performance and guarantees clear
and bright video.
1.4 Specifications
Please refer to the following sheet for specification.
Model
Parameter
1 Megapixel HDCVI IR Vari-focal
Waterproof Fixed Camera
2 Megapixel HDCVI IR Vari-focal
Waterproof Fixed Camera
HAC-HFW2100RP/N-VF
HAC-HFW2200RP/N-VF
Video Processor
1/3" 1.37 Mega Pixels CMOS
1/2.8" 2.43 Mega Pixels CMOS
Video Format
PAL/NTSC
Effective Pixel
1305(H) ×1049(V)
1984(H) ×1225(V)
Min Illumination
0.01Lux@（F1.2,AGC ON），0 Lux
with IR
0.05Lux@（F1.2，AGCON），0 Lux
with IR
Electronic Shutter
Support slow shutter，1/3s～1/1000,000s
Video Standard
HDCVI/CVBS compliance
Video Frame Rate
1280×720@25 fps；1280×720@30
fps；1280×720@50 fps；
1280×720@60 fps
1920×1080@25fps；
1920×1080@30fps；1280×720@25
fps；1280×720@30 fps；
1280×720@50 fps；1280×720@60
fps；
Lens Port
Φ14
Lens Type
2.7-12mm@F1.4 fixed iris manual vari-focal lens
Day/Night Switch
ICR auto switch
Video Output
1-channel HDCVI high definition video output/ CVBS standard definition video
output (Can switch.)
Denoise (Noise
Reduction)
Support 2D/3D denoise.
OSD Menu Control
Support coaxial cable control
OSD
EXPOSURE
Exposure Mode/ Exp Level/ Exp Speed/ Anti-flicker/BLC
WHITE
BALANCE
Auto/ Manual/ Day/ Night/Indoor/Outdoor
DAY/NIGHT
Auto/B&W/Color
Function
2DNR/3DNR/ D-Zoom/ Lens/Lens Reset
Advanced
CAM Title/ Mirror&Flip/ Privacy Mask/ Language/Com setup/System Info
IMAGE
Sharpness /Brightness/Contrastness/Saturation/ Sharp Suppress/ Chroma
suppress/ Gamma/ Video Format

3
RESET
----
EXIT
----
Max IR Distance
30m
Transmission
Distance
Over 500m via 75-3 coaxial cable.
Over 300m via 75-3 coaxial cable.
Protection Level
IP66
Working Temperature
/Humidity
-30℃~+60℃. Humidity is less than 95%(no condensation)
Power
DC 12V±10%
Power Consumption
Dimension(mm)
213×80×72
Angle Adjustment
Pan: 0°～360°: Tilt: 0°～90°: Flip: 0°～360°
Weight
550g
Installation Mode
Wall mount

4
2Framework and Dimensions
2.1 Dimensions
Please refer to the following figure for dimension information. The unit is mm. See Figure 2-1.
Figure 2-1
2.2 Structure
Please refer to the following figures for structure information. See Figure 2-2 and Figure 2-3.
Figure 2-2
When the standard definition/high definition switch control cable is short circuit, system outputs
standard definition video. Otherwise, when the circuit is open, system outputs the high
definition video.

5
Figure 2-3

6
3 Installation
Important
Please make sure the installation surface can min support the 3X weight of the camera
and the bracket.
Figure 3-1
Step1
Take out the camera cable through cable exit of the bracket chassis and install camera bracket.
If it is cement wall, you need to install expansion bolt first (the installation hole of expansion
bolt need to be in accordance with the bracket), then use self-tapping bolt to install bracket,
which is shown in Figure 3-1.
If it is wooden wall, you can skip the first step and use self-tapping bolt to install bracket
directly.
Step 2
Unscrew the M3×20 and M3×5 screws on the bracket in the direction shown in Figure 3-2,
adjust the camera to an exact location which needs to be monitored by rotating the bracket
and camera body, then secure the bolts.

7
Figure 3-2
Step 3
Connect the video output port of the device cable to the HDCVI DVR, and connect the power
port of the device cable to the power.
Step 4
After the image is shown on the HDCVI DVR, open the lower cover of the camera and adjust
lens focal length by focus/zoom lever to make the image clear and secure the lever. Retighten
the camera lower cover and complete the installation.

8
4Menu
4.1 HDCVI Series DVR Settings
Note
The following operation and interfaces for reference only. Please refer to the HDCVI
series DVR user’s manual for detailed information.
After connected the camera to the HDCVI series DVR, from Main Menu->Setting->System-
>PTZ, you need to set control mode as HDCVI and the protocol as DH-SD1. Click Save button
to save current setup. See Figure 4-1.
Figure 4-1
On the preview interface, right click mouse and then select PTZ; you can see an interface
shown as below. See Figure 4-2.
Figure 4-2
Click Iris “+”to open menu or confirm current operation.

9
Click up/down button to view all the items on the left pane of the following list. Click left/right
button to set the corresponding values on the right pane of the following list. If there is “ ”,
click confirm button to go to the 2nd menu. Repeat the previous steps to set detailed value.
Click Return button to go back to the previous menu interface.
4.2 Menu List
The 1st
The 2nd
The 3rd
Exposure
Exposure
Mode
Auto
Gain Max
0～100
Gain Min
0～100
Low
Noise
Gain Max
0～100
Gain Min
0～100
Return&Exit
For the 2nd and the 3rd
menu, when you click Exit
button to exit, system
saves current setup by
default.
Low Motion
Blur
Shutter Max
PAL: 0ms～40ms
NTSC: 0ms～33ms
Shutter Min
PAL: 0ms～40ms
NTSC: 0ms～33ms
Return&Exit
Manual
Shutter
1/100000, 1/10000,
1/4000,1/2000,1/1000,1/500,
1/250,1/120,1/100,1/60,1/50,
1/30,1/25,1/15,1/12,1/10,1/8,
1/6,1/5,1/4,1/3
Customized
Gain Max
0～100
Gain Min
0～100
Return&Exit
Exp Level
0～14
Exp Speed
0～7
Anti-flicker
Outoodr/50H
Z/60HZ
50HZ: 1/50, 1/100, 1/25,
1/10, 1/5, 1/4.
60HZ: 1/60, 1/120, 1/30,
1/4, 1/12, 1/6.
The 50HZ and 60HZ mode
have different manual
exposure mode and there
is no low motion blur and
low noise exposure mode.
BLC
BLC
OFF/ON
WDR
0～100
HLC
0～100
The HLC is valid when auto
exposure and outdoor anti-
flicker mode are both valid.
Return&Exit
White
Balance
Auto
Manual
Blue
1～100
Red
1～100
Return&Ex
it
Day
Night
Indoor
Outdoor
Day/Night
Auto
Day→
Night
1～100

10
The 1st
The 2nd
The 3rd
Return&Ex
it
B/W
Color
Function
2DNR
0～100
3DNR
0～100
D-Zoom
1～10
Lens
Manual/DC
Return&Ex
it
Advanced
CAM
Title
Mirror/Flip
Mirror
OFF/ON
Flip
OFF/ON
Return&Exit
Privacy
Mask
OFF
ON
Area Sel
0～7
There are eight privacy
mask zones ranging from 0
to 7. You need to set
parameters for each zone.
Area state
OFF/ON
Area setup
Position
Size
Use direction buttons to set
position and zone size.
Default
Return&Exit
Language
EN
COM
Setup
Address
1～254
Apply
Return&Exit
System
Info
Version
XXXXXXXXX
Return&Exit
Image
Sharpness
0～100
Brightness
0～100
Contrastne
ss
0～100
Saturation
0～100
Sharp
Suppress
0～100
Chroma
suppress
0～100
Gamma
0～15
Video
Format
/720P@25
/720P@3
0 /720P@
50 /720P
@60
OK/CANCEL
1080P series support
1080P@25, 1080P@30,
720P@25, 720P@30,
720P@50, 720P@60
Return&Exi
t
Reset
Exit
4.3 Note

11
Parameter
Function
Brightness
It is to adjust monitor window bright. The value ranges from 0 to
100. The default value is 50.
The larger the number is, the bright the video is. When you
input the value here, the bright section and the dark section of
the video will be adjusted accordingly. You can use this
function when the whole video is too dark or too bright. Please
note the video may become hazy if the value is too high. The
recommended value ranges from 40 to 60.
Contrast
It is to adjust monitor window contrast. The value ranges from 0
to 100. The default value is 50.
The larger the number is, the higher the contrast is. You can
use this function when the whole video bright is OK but the
contrast is not proper. Please note the video may become hazy
if the value is too low. If this value is too high, the dark section
may lack brightness while the bright section may over
exposure .The recommended value ranges from 40 to 60.
Saturation
It is to adjust monitor window saturation. The value ranges from
0 to 100. The default value is 50.
The larger the number, the strong the color is. This value has
no effect on the general brightness of the whole video. The
video color may become too strong if the value is too high. For
the grey part of the video, the distortion may occur if the white
balance is not accurate. Please note the video may not be
attractive if the value is too low. The recommended value
ranges from 40 to 60.
Sharpness
The value here is to adjust the edge of the video. The value
ranges from 0 to 100. The larger the value is, the clear the edge
is and vice versa. Please note there is noise if the value here is
too high. The default value is 50 and the recommended value
ranges from 40 to 60.
3DNR
It is to reduce video noise. The larger the number is, the lower
the noise is. The details of the video may disappear if the value
here is too large.
Anti-flicker
Outdoor: In this mode, you can switch exposure mode to
get the effect under the corresponding exposure mode.
50Hz: When the current is 50Hz, system can auto adjust
the exposure according to the environment brightness in
case there is any strip.
60Hz: When the current is 60Hz, system can auto adjust
the exposure according to the environment brightness in
case there is any strip.

12
Appendix Toxic or Hazardous Materials or Elements
Component
Name
Toxic or Hazardous Materials or Elements
Pb
Hg
Cd
Cr VI
PBB
PBDE
Circuit Board
Component
○
○
○
○
○
○
Device
Construction
Material
○
○
○
○
○
○
Wire and Cable
○
○
○
○
○
○
Packing
Components
○
○
○
○
○
○
Accessories
○
○
○
○
○
○
O: Indicates that the concentration of the hazardous substance in all homogeneous materials
in the parts is below the relevant threshold of the SJ/T11363-2006 standard.
X: Indicates that the concentration of the hazardous substance of at least one of all
homogeneous materials in the parts is above the relevant threshold of the SJ/T11363-2006
standard. During the environmental-friendly use period (EFUP) period, the toxic or hazardous
substance or elements contained in products will not leak or mutate so that the use of these
(substances or elements) will not result in any severe environmental pollution, any bodily injury
or damage to any assets. The consumer is not authorized to process such kind of substances
or elements, please return to the corresponding local authorities to process according to your
local government statutes.
Note
This manual is for reference only. Slight difference may be found in the user
interface.
All the designs and software here are subject to change without prior written
notice.
All trademarks and registered trademarks mentioned are the properties of their
respective owners.
If there is any uncertainty or controversy, please refer to the final explanation of
us.
Please visit our website or contact your local service engineer for more
information.