Dahua EBW8600 User manual

HD Fisheye Panorama Network Camera Quick Start Guide
Version 1.1.0
i

Welcome
Thank you for purchasing our network camera!
This user’s manual is designed to be a reference tool for your system.
Please read the following safeguard and warnings carefully before you use this series
product!
Pleasekeep this user’s manual well for future reference!
1
．
Electrical safety
All installation and operation here should conform to your local electrical safety codes.
The power shall conform to the requirement in the SELV(Safety Extra Low Voltage) and
theLimited power source is rated 12V DC in the IEC60950-1. This series product
supports PoE too.
Note: Do not connect these two power supplying sources to the device at the same
time; it may result in device damage!
We assume no liability or responsibility for all the fires or electrical shock caused by
improper handling or installation.
We are not liable for any problems caused by unauthorized modification or attempted
repair.
2
．
Transportation security
Heavy stress, violent vibration or water splash are not allowed during transportation,
storage and installation.
3
．
Installation
Do not apply power to the camera before completing installation.
Please install the proper power cut-off device during the installation connection.
Always follow the instruction guide the manufacturer recommended.
4
．
Qualified engineers needed
All the examination and repair work should be done by the qualified service engineers.
We are not liable for any problems caused by unauthorized modifications or attempted
repair.
5
．
Environment
This series network camera should be installed in a cool, dry place away from direct
sunlight, inflammable, explosive substances and etc.
i

Please keep it away from the electromagnetic radiation object and environment.
Please make sure the CCD (CMOS) component is out of the radiation of the laser beam
device. Otherwise it may result in CCD (CMOS) optical component damage.
Pleasekeep thesound ventilation.
Do not allow the water and other liquid falling into the camera.
Thunder-proof device is recommended to be adopted to better prevent thunder.
The grounding holes of the product are recommended to be grounded to further enhance
the reliability of the camera.
6. Daily Maintenance
Pleaseshut down the device and then unplug the power cable before you begin daily
maintenance work.
Do not touch the CCD (CMOS) optic component. You can use the blower to clean the
dust on the lens surface.
Always use the dry soft cloth to clean the device. If there is too much dust, please use
the water to dilute the mild detergent first and then use it to clean the device. Finally use
the dry cloth to clean the device.
Please put the dustproof cap to protect the CCD (CMOS) component when you do not
use the camera.
Dome enclosure is the optical component, do not touch the enclosure when you are
installing the device or clean the enclosure when you are doing maintenance work.
7. Accessories
Be sure to use all the accessories recommended by manufacturer.
Before installation, please open the package and check all the components are included.
Contact your local retailer ASAP if something isbroken in your package.
Accessory Name Amount
Network Camera 1
Quick Start Guide
1
Installation Accessories Bag
1
CD 1
ii

Table of Contents
1Structure..........................................................................................................1
1.1 Device External Cable ......................................................................1
1.2 Dimensions........................................................................................2
1.3 Bidirectional Talk...............................................................................2
1.3.1 Device-end to PC-end................................................................2
1.3.2 PC-end to Device-end................................................................3
1.4 Alarm Setup.......................................................................................3
2Installation.......................................................................................................4
2.1 General Installation ...........................................................................4
2.2 Device Installation Steps ..................................................................4
2.3 Micro SD Card Installation................................................................5
2.4 Manual Zoom Lens Focus Operation...............................................6
3Quick Configuration Tool ...............................................................................7
3.1 Overview............................................................................................7
3.2 Operation...........................................................................................7
4Web Operation ...............................................................................................9
4.1 Network Connection..........................................................................9
4.2 Login and Main Interface..................................................................9
4.3 Panorama Function on Web...........................................................11
4.3.1 Installation Mode.......................................................................11
4.3.2 Display Mode ............................................................................11
Appendix Toxic or Hazardous Materials or Elements.......................................12
iii

1 Structure
1.1 Device External Cable
Figure 1- 1
The device external cable is shown in Figure 1- 1.
Please refer to Sheet 1-1 for corresponding information about external cable functions.
NO.
Port
Port Name
Connector
Function Description
1 AUDIO
OUT Audio output
port RCA Output audio signal to the speakers.
2 AUDIO IN Audio input
port RCA
Input audio signal, receive the analog audio signal
from the sound pick-up.
3 LAN Network port Ethernet
port Connect to standard Ethernet cable.
4 I/O I/O port - Connect I/O port
5 POWER Power input
port - Connect DC 12V power, input power
Sheet 1-1
Please refer to Sheet 1-2 for corresponding information about I/O port functions.
Port Name Cable
Number Cable Port
Name Function Description
I/O port 1 ALARM_NO

Alarm output port. It is to output the alarm signal
to the alarm device.
NO：Normal open alarm output port.
This port needs to be used with ALARM_COM
port
1

Port Name Cable
Number Cable Port
Name Function Description
2 ALARM_COM Alarm output public port.
3 ALARM_IN1 Alarm input port 1. It is to receive the on-off signal
from the external alarm source.
4 ALARM_IN2 Alarm input port 2. It is to receive the on-off signal
from the external alarm source.
5 GND Ground port
Sheet 1-2
1.2 Dimensions
Note:
There are two standards for side dimension of the device,which are: 33.7mm, 47.7mm and
36.6mm, 50.7mm. Please refer to the actual product model for more details.
You can refer to the following figures for dimension information. The Unit is mm. See Figure 1-2 to
Figure 1-4.
Figure 1-2
Figure 1-3 Figure 1-4
1.3 Bidirectional Talk
1.3.1 Device-end to PC-end
Device Connection
Please connect the speaker or MIC to the audio input port of the PC, and then connect the earphones
to the audio output port of the PC. Login theWeb and then click the Talk button to enable the
2

bidirectional talk function. You can see the button becomes orange after you enabled the bidirectional
talk function. ClickTalk button again to stop the bidirectional talk function.
Listening Operation
At the device end, speak via the speaker or MIC, and then you can get the audio at the pc-end.
1.3.2 PC-end to Device-end
Device Connection
First connect the speaker or MIC to the audio input port of the PC, and then connect the earphones to
theaudio output port of the PC. Login theWeb and then click the “Talk” button to enable the
bidirectional talk function. You can see the button became orange after you enabled the bidirectional
talk function. Click “Talk” button again to stop the bidirectional talk function. Bidirectional talk function
and on-site listening function can’t be used at the same time for the device.
Listening Operation
At the PC end, speak via the speaker or MIC, and then you can get the audio at the device-end.
1.4 Alarm Setup
Please refer to Figure 1-5 for more information about alarm setup.
Figure 1-5
Pleasefollow the steps listed below for alarm input and output connection.
Step 1 Connect the alarm input device to the alarm input port (No.4 pin) of the I/O cable.
Step 2 Connect alarm output deviceto alarm output port (No.1pin) and alarm output public port
(No.2pin), The alarm output port supports NO (normal open) alarm device only.
Step 3 Open WEB and set corresponding alarm input and output in the alarm setup. Please set the
alarm input 01port for the first channel of the I/O cable (No.4 pin). Then set corresponding
NO/NC input according to the high/low level signal generated when alarm occurs to the alarm
input device.
Step 4 Set the WEB alarm output. The alarm output 01 is for the alarm output port of the device. It is
the No.1 pin of the I/O cable.
3

2 Installation
Important
Before you complete the installation and setup, do not remove the electrostatic
attraction film on the transparent enclosure. Otherwise it may result in injury.
After remove electrostatic attraction film, do not touch dome enclosure in case
it may leave stain.
Before the installation, please make sure the installation surface can sustain at
least 3X weight of the bracket and the camera.
2.1 General Installation
Please refer to Figure 2- 1 for device installation information. You can see there are installation screws
in theaccessories bag for you to install the device conveniently.
Figure 2- 1
2.2 Device Installation Steps
Step 1
Take the installation position diagram from theaccessories bag and then paste it on the installation
ceiling or the wall according to the monitor area. Please dig three bottom holes of the plastic
expansion bolts according to the diagram. If you need to dig a hole to pull through the cable on top of
installation surface, you need to dig a cable exit hole of no less than 28MM on the installation surface
according to the installation positioning diagram, which makes the network cable go through.
4

Step 2
Insert 3 expansion bolts from theaccessories bag into the bottom holes and lock them firmly, adjust
theposition of device installation pedestal and pull the cable through the cableexit hole on the
installation surface.
Step 3
Aim 3 screw fixed holes on the installation chassis to 3 plastic expansion bolt fixed holes on the
installation surface, then tighten 3 ST3 self-tapping screws into 3 plastic expansion bolts and fasten
them firmly, fix the installation chassis on the installation surface.
Step 4
When installing dome body, find the little gap on the dome body and make it corresponding to the
“TOP” direction on the installation chassis, rotate the dome body in clockwisedirection and secure it
firmly. So far, installation is completed.
Note:
Pleaserefer to Micro SD card installation steps if you need to install Micro SD card, and operate step 4
after the installation.
Note: If connect the host GND to ground lead, may improve device reliability. The
GND locates next to exit hole on the rear side of the chassis and the GND screw is
M3.
Figure 2- 2
2.3 Micro SD Card Installation
Use the inner hex wrench from the accessories bag tounfasten the 3 inner hex screws on the dome
camera enclosure, find the Micro SD card slot position according to the following figure then fasten
back the 3 screws on the dome camera enclosure after the Micro SD card is inserted.
Note:
5

Please make sure the wire between power panel and device motherboard is firm,
otherwise may cause abnormity.
Please put the enclosure back and fasten the screws tightly to prevent dust.
Figure 2-3
2.4 Manual Zoom Lens Focus Operation
The lens of the HD panorama dome network camera is 360°, no manual zoom is required when it is
operated by in-ceiling mount or ground mount.
The lens of the HD panorama dome network camera is 185°, no manual zoom is required when it is
operated by wall mount.
6