Dahua NKB1000 Installation and user guide

Equipment Model Firmware Course Version Date
NKB1000 V20180115 V1.0 2018/2/9
· How to control the PTZ camera with keyboard?

Page1
Copyright © 2017 Dahua Technologies Co., Ltd.All rights reserved.
ConnectionVia Network/RS485 Network/Address Config Operation
…
Network
…
Control PTZ Camera (HDCVI/Analog/IP) via network or RS485
Keyboard Control PTZ Camera
· How to control the PTZ camera with keyboard?

Page2
Copyright © 2017 Dahua Technologies Co., Ltd.All rights reserved.
ConnectionVia RS485 Network/Address Config Operation
…
Network
…
Control PTZ Camera (HDCVI/Analog/IP) via network or RS485
Keyboard Control PTZ Camera(Via RS485)
· How to control the PTZ camera with keyboard via RS485?

Page3
Copyright © 2017 Dahua Technologies Co., Ltd.All rights reserved.
①Controlling PTZ Cameras – Via RS485.
ConnectionVia RS485 Address Config Operation
RS485
Keyboard Control PTZ Camera
· How to control the PTZ camera with keyboard via RS485?

Page4
Copyright © 2017 Dahua Technologies Co., Ltd.All rights reserved.
Suppose the RS485 address of the PTZ camera is 100, baud rate is 9600, protocol is Pelco-D, then we
should add a “zone” in the keyboard as follows:
ConnectionVia RS485 Address Config Operation
ID: 1
Name: Door1
Type: SD
Link: COM485
485Addr: 100
Rule: PELCOD
BaudRate: 9600
DataBit: 8
Parity: None
StopBit: 1
Note: you can set any ID or Name, but should set other parts based on the actual configuration of the PTZ camera.
RS485connection is available for NKB1000/KBD1000/KB1000.
Keyboard Control PTZ Camera
· How to control the PTZ camera with keyboard via RS485?

Page5
Copyright © 2017 Dahua Technologies Co., Ltd.All rights reserved.
ConnectionVia Network Network/Address Config Operation
…
Network
…
Control PTZ Camera (HDCVI/Analog/IP) via network or RS485
Keyboard Control PTZ Camera(Via Network)
· How to control the PTZ camera with keyboard via network?

Page6
Copyright © 2017 Dahua Technologies Co., Ltd.All rights reserved.
②Controlling PTZ Cameras – Via Network
ConnectionVia Network Network Config Operation
Network
Keyboard Control PTZ Camera(Via Network)
· How to control the PTZ camera with keyboard via network?

Page7
Copyright © 2017 Dahua Technologies Co., Ltd.All rights reserved.
Suppose the IP address of the PTZ camera is 10.15.7.3, port is 37777, password of admin is “qwerty”. Then
we should add a “zone” in the keyboard as follows:
ConnectionVia Network Network Config Operation
ID: 1
Name: Door1
Type: SD
Link: NET
IPAddr: 10.15.7.3
Port: 37777
Rule: DH-2
PW: qwerty
Note: you can set any ID or Name, but should set other parts based on the actual settings of the PTZ camera.
Network connection is only available for NKB1000.
Keyboard Control PTZ Camera(Via Network)
· How to control the PTZ camera with keyboard via network?

Page8
Copyright © 2017 Dahua Technologies Co., Ltd.All rights reserved.
After you’ve added the PTZ camera to the “zone” list of the keyboard.
Enter the “Zone Control” menu, input the ID of the PTZ camera, click “ENTER”, the keyboard will connect to
the PTZ camera and show the following interface.
You can also choose other ways to connect: name, address, etc.
ConnectionVia Network/RS485 Network/Address Config Operation
Keyboard Control PTZ Camera
· How to control the PTZ camera with keyboard?

Page9
Copyright © 2017 Dahua Technologies Co., Ltd.All rights reserved.
IRIS: control the aperture
FOCUS: control the focus
ZOOM: zoom in/out
OTHER: Speed dome OSD
menu
PRESET: Set/call preset
SCAN: Set/call scan
PAN: Call pan
TOUR: Set/call tour
PATTERN: Set/call pattern
Pan/Tilt/Zoom
Keyboard Control PTZ Camera
ConnectionVia Network/RS485 Network/Address Config Operation
· How to control the PTZ camera with keyboard?