Dahua HAC-HF3101 User manual

1 Megapixel ICR Day/Night WDR
Fixed HDCVI Camera User’s Manual
Version 1.0.0

i
Table of Contents
1General Introduction ..................................................................................................................1
1.1 Overview........................................................................................................................1
1.2 Functions .......................................................................................................................1
1.3 Specifications................................................................................................................1
2Framework...................................................................................................................................3
2.1 Rear Panel.....................................................................................................................3
2.2 Side panel......................................................................................................................4
2.3 Front Panel....................................................................................................................5
3Installation ...................................................................................................................................6
3.1 Lens Installation............................................................................................................6
3.2 I/O Port Installation.......................................................................................................7
4Menu.............................................................................................................................................8
Appendix Toxic or Hazardous Materials or Elements ...............................................................12

ii
Welcome
Thank you for purchasing our HDCVI camera!
This user’s manual is designed to be a reference tool for your system.
Please read the following safeguard and warnings carefully before you use this series product!
Please keep this user’s manual well for future reference!

iii
Important Safeguards and Warnings
1．Electrical safety
All installation and operation here should conform to your local electrical safety codes.
The power shall conform to the requirement in the SELV (Safety Extra Low Voltage) and the Limited
power source is rated 12V DC or Ac 24V in the IEC60950-1.
We assume no liability or responsibility for all the fires or electrical shock caused by improper handling
or installation.
2．Transportation security
Heavy stress, violent vibration or water splash are not allowed during transportation, storage and
installation.
3．Installation
Do not apply power to the camera before completing installation.
Please install the proper power cut-off device during the installation connection.
Always follow the instruction guide the manufacturer recommended.
If this product is installed in the ceiling, please make sure the installation position can sustain the min
50N.
4．Qualified engineers needed
All the examination and repair work should be done by the qualified service engineers.
We are not liable for any problems caused by unauthorized modifications or attempted repair.
5．Environment
This series HDCVI camera should be installed in a cool, dry place away from direct sunlight or strong
light, inflammable, explosive substances and etc.
This series camera shall work on the specified working temperature. Please keep it away from the
electromagnetic radiation object and environment.
Please make sure the CMOS component is out of the radiation of the laser beam device. Otherwise it
may result in CMOS optical component damage.
Please keep the sound ventilation.
Do not allow the water and other liquid falling into the camera.
6. Accessories
Be sure to use all the accessories recommended by manufacturer.
Before installation, please open the package and check all the components are included.
Contact your local retailer ASAP if something is broken in your package.
7. Daily Maintenance

iv
Please shut down the device and then unplug the power cable before you begin daily maintenance
work.
Use the dry soft cloth to clean the device. If there is too much dust, please use the water to dilute the
mild detergent first and then use it to clean the device. Finally use the dry cloth to clean the device.
Please put the dustproof cap to protect the CMOS component when you do not use the camera.

1
1General Introduction
1.1 Overview
This series megapixel HD camera conforms to the HDCVI standard. It supports video signal
high-speed long distance transmission without any delay. The HDCVI port adopts coaxial
cable and uses BNC port as the standard cable.
This series product has megapixel definition. It supports DC 12V/AC 24V power supplying. It
supports HDCVI HD and CVBS standard definition output, and OSD operation.
1.2 Functions
Data Transmission
It adopts coaxial cable and use BNC port as the standard cable specifications.
Peripheral Device Control
It can be controlled by the DVR conforming to the HDCVI specifications via the video coaxial
cable
Power Supplying
Support external power adapter supplying. Support AC 24V/DC 12V.
Aux Function
zAuto day/night switch (With ICR switch)
zThe WDR can max reach 120dB, suitable for the backlight environments.
zSupport video/audio/control signal transmission over the same coaxial cable.
zGeneral 75-3 coaxial cable supports over 500m transmission distance without any quality
loss.
zSupport 1280*720@25fps, 1280*720@30fps
z3D NR function
zSupport privacy mask function.
zSupport auto iris function.
zSupport OSD operation.
zHDCVI HD/standard definition output switch function.
1.3 Specifications
Please refer to the following sheet for specification.
1 Megapixel ICR Day/Nigh WDR Fixed HDCVI CameraModel
Parameter HAC-HF3101P/N
Video
Processor 1/3" 1.3 Megapixels CMOS
Video
Video Format PAL/NTSC

2
Sensor Pixel 1280(H)×960(V)
Min
Illumination Color: 0.01Lux@（F1.2,AGC ON）,
Black and white: 0.001Lux@（F1.2,AGC ON）,
Electronic
Shutter 1/1s～1/10000s@ (slow shutter*512）
Video Standard HDCVI/CVBS compliance
Video Frame
Rate 1280*720@25fps ;1280*720@30fps
Day/Night
Switch ICR mechanical auto switch
Lens Port C/CS
Auto Iris DC Drive
WDR Range 120dB
Audio/Video
Transmission Support audio/video transmission over the same coaxial cable.
Control Signal
Transmission Support OSD control and video transmission over the same coaxial cable.
SCENE INDOOR/OUTDOOR/WDR
EXPOSURE AUTO/AUTO IRIS/AUTO SHUTTER/MANUAL
FUNCTION WB/WDR/NR/MIRROR/DAY&NIGHT/HLC/BLC
IMAGE MODE/HUE CNT/SHARPNESS/SHARP
CNT/BRIGHTNESS/SATURATION/HUE/GAMMA
ADVANCED MOTION DETECT/PRIVACY MASK/FREEZE/ALARM MODE/RS-
485/CAMERA ID/LANGUAGE/SYSTEM INFO
OSD
EXIT INDOOR/RESTART/FORMAT/BACK
Video Output 1-channel BNC HDCVI HD/CVBS standard definition output (Can switch)
Audio Input 1-channel audio input port. Connect to devices such as pick up.
Standard
Definition/HD
Switch
Hardware button. Press for 5 seconds to switch standard definition/HD
definition mode.
ICR External
Trigger External trigger signal to activate day/night mode switch.
Alarm Output 1-channel on-off signal output. Can activate motion alarm.
AUX
Port
RS485 port Support OSD operation. Software online upgrade.
Power
Supplying AC 24V/DC 12V
Power
Consumption 7W Max (Input:12V 0.58A/24V～0.52A)
Working
Temperature
/Humidity -30℃~+60℃. Humidity is less than 95%(no condensation)
Dimension(mm) 70×63.2×136.5
Weight 650g
General
Installation
Mode Support various installation modes (Housing and bracket is optional)

3
2Framework
2.1 Rear Panel
Please refer to the following figure for the rear panel information. See Figure 2-1.
Figure 2-1
Port Name Connector Port Function
AC 24V/DC
12V Power port zPower port.
zConnect to AC 24V/ DC 12V.
Red light Power light. The light is on after system boots
up.
Green light Hardware indicator light. The light becomes
on after system successfully loads the
hardware part.
Indicator
light
Yellow light HD/standard definition indicator light. The
light is off when system is using the HD
output. The light is on when system is using
standard definition.
IN ICR external
trigger
Connect to external on-off output to control
ICR switch to realize day/night mode switch.
Please note: if you want to use this function,
you need to go to the OSD menu to set the
day/night mode as EXT TRIG-HIGH or EXT
TRIG-LOW. The control signal shall connect
to the IN and G port. For example, connect
the 5V to the IN port and the day/night mode
as EXT TRIG-HIGH , the camera can switch
from day mode to night mode.
NO Alarm normal open
contact On-off signal alarm output.
C Alarm output public
contact On-off signal alarm output.

4
Port Name Connector Port Function
G GND Ground end.
A RS485_A port. Connect to DVR or RS485
configuration tool to set video parameters.
B RS485 port RS485_B port. Connect to DVR or RS485
configuration tool to set video parameters.
NA N/A Reserved
RX
TX
G
Reserved port For R/D use only.
RESET Reset button Press it for five seconds, system can reload
again and restore factory default setup.
HDCVI Video/audio/control
composite port
Send video stream/audio stream/control data
stream conforming to HDCVI specifications.
Please connect to the HDCVI DVR series
product to control.
MIC IN Microphone audio
input Audio input from the pickup.
5-direction
button OSD button
zPress the middle button for five
seconds to switch HD/standard
definition mode.
zPress the middle button shortly to go to
the OSD menu interface.
zAfter you go to the menu, click the
middle button to confirm current
operation. Move the up/down button to
select menu item and use left/right
button to set parameter value.
GND port
Before you use this series product, please
make sure it has been soundly grounded in
case there is a risk of thunder strike.
2.2 Side panel
Please refer to the following figure for the rear panel information. The unit is mm. See Figure
2-2.

5
Figure 2-2
2.3 Front Panel
Please refer to the following figure for the front panel information. The unit is mm. See Figure
2-3.
Figure 2-3

6
3Installation
Important
zBefore the installation, please make sure the installation surface can sustain at
least 3X weight of the bracket and the camera.
3.1 Lens Installation
Please refer to the steps listed below for installation information. See Figure 3-1 and Figure 3-2.
zRemove the protection cap from the device. Line up the lens to the lens position of the
camera (Install the C/CS adapter ring to the camera if you are using C type lens).Turn
clockwise to secure the lens firmly.
zInsert the socket of the lens cable to the auto iris lens connector on the side panel of the
device. Skip this step if you are using auto iris lens.
zFasten the screw near the focusing ring and then turn counter clockwise to move the
focusing ring out for several millimeters. Now you can focus manually until you get clear
video.
zAfter you completed the focus setup, fix the screw near the focusing ring firmly. Fasten the
focusing ring. Now the installation is complete.
Figure 3-1

7
Figure 3-2
3.2 I/O Port Installation
Install Cable
Please follow the steps listed below to install the cable. See Figure 3-3.
Use the small slotted screwdriver to press the corresponding button of cable groove. Insert the
cable into the groove and then release the screwdriver.
Remove Cable
Please follow the steps listed below to remove the cable.
Use the small slotted screwdriver to press the corresponding button of cable groove. Remove
the cable out of the groove and then release the screwdriver.
Figure 3-3

8
4Menu
Important
Please check the current video output mode when there is no video output. The yellow
light is on when system is outputting standard definition video. The yellow light is off
when system is using high definition video.
THE 1ST MENU THE 2ND MENU THE 3RD MENU
SCENE
INDOOR
SCENE
OUTDOOR
SCENE WDR
SCENE
BACK
MAX SPEED
MIN SPEED
PAL:
1/25, 1/50, 1/75, 1/100, 1/120,
1/150, 1/215, 1/300, 1/425, 1/600,
1/1000, 1/1250, 1/1750, 1/2500,
1/3500, 1/6000, 1/10000
NTSC:
1/30,1/60,1/90,1/100,1/125,1/180,
1/250,1/350,1/500,1/725,1/1000,1
/1500,1/2000,1/3000,1/4000,1/60
00,1/10000.
SLOW SHUTTER PAL:
1/1,1/2,1/3,1/6,1/12,1/25,1/50,1/7
5,1/100,1/120
NTSC:
1/1, 1/2, 1/4, 1/8, 1/15, 1/30,1/60,
1/90,1/100,1/125
SHUTTER
AUTO…
BACK
GAIN -1,0,2,4,6,8,10,12,14,16,18,20,22,24,26,28（DB）
LENS--- It is read-only on auto mode.
EC OFF,+0,+1,+2,+3,+4,+5,+6,+7,-1,-2,-3,-4,-5,-6,-7
LLC 0,5,10,15,20,25,30,35,40,45,50,55,60,65,70,75,80,85,90,95,1
00
AUTO
BACK
SHUTTER PAL:
1/25, 1/50, 1/75, 1/100, 1/120, 1/150, 1/215, 1/300, 1/425,
1/600, 1/1000, 1/1250, 1/1750, 1/2500, 1/3500, 1/6000,
1/10000
NTSC:
1/30,1/60,1/90,1/100,1/125,1/180,1/250,1/350,1/500,1/725,1/
1000,1/1500,1/2000,1/3000,1/4000,1/6000,1/10000.
GAIN -1,0,2,4,6,8,10,12,14,16,18,20,22,24,26,28（DB）
LENS It is read-only on auto iris mode.
EC OFF,+0,+1,+2,+3,+4,+5,+6,+7,-1,-2,-3,-4,-5,-6,-7
LLC 0,5,10,15,20,25,30,35,40,45,50,55,60,65,70,75,80,85,90,95,1
00
IRIS
BACK
MAX SPEED
EXPOSURE
SHUTTER SHUTTER
AUTO… MIN SPEED
PAL:
1/25, 1/50, 1/75, 1/100, 1/120,
1/150, 1/215, 1/300, 1/425, 1/600,
1/1000, 1/1250, 1/1750, 1/2500,
1/3500, 1/6000, 1/10000
NTSC:
1/30,1/60,1/90,1/100,1/125,1/180,
1/250,1/350,1/500,1/725,1/1000,1

9
/1500,1/2000,1/3000,1/4000,1/60
00,1/10000.
SLOW SHUTTER PAL:
1/1,1/2,1/3,1/6,1/12,1/25,1/50,1/7
5,1/100,1/120
NTSC:
1/1, 1/2, 1/4, 1/8, 1/15, 1/30,1/60,
1/90,1/100,1/125
BACK
GAIN -1,0,2,4,6,8,10,12,14,16,18,20,22,24,26,28（DB）
LENS It is read-only on auto shutter mode.
EC OFF,+0,+1.+2,+3,+4,+5,+6,+7,-1,-2,-3,-4,-5,-6,-7
LLC 0,5,10,15,20,25,30,35,40,45,50,55,60,65,70,75,80,85,90,95,1
00
BACK
SHUTTER PAL:
1/25, 1/50, 1/75, 1/100, 1/120, 1/150, 1/215, 1/300, 1/425,
1/600, 1/1000, 1/1250, 1/1750, 1/2500, 1/3500, 1/6000,
1/10000
NTSC:
1/30,1/60,1/90,1/100,1/125,1/180,1/250,1/350,1/500,1/725,1/
1000,1/1500,1/2000,1/3000,1/4000,1/6000,1/10000.
GAIN -1,0,2,4,6,8,10,12,14,16,18,20,22,24,26,28（DB）
LENS MODE OPEN, MODE
OFF
EC It is read-only on manual mode.
LLC It is read-only on manual mode.
MANUAL
BACK
AUTO
INDOOR
OUTDOOR
ONE PUSH
ATW
RED GAIN 000-255MANUAL…
BLUE GAIN 000-255
OUTDOOR
AUTO
SODIUM
AUTO
WB
SODIUM
OFF
INTENSITY 1-5
MOTION COMP
WDR
ON…
RETURN
2D-NR OFF, 1-5
3D-NR OFF, 1-5
NR…
BACK
MIRROR OFF, V-FLI,H-FLIP, CENTRE
SWITCH POINT 1-7
TOLERANCE 1-6
DAYÆNIGHT 2S-30S
NIGHT ÆDAY 2S-30S
AUTO …
BACK
DAY
NIGHT
EXT TRIG-
HIGH
FUNCTION
D/N
EXT TRIG-

10
LOW
HLC OFF, 1, 2
BLC OFF,1, 2
BACK
MODE CUSTOM , FLAMBOYANT,SOFT,
Note: For non-custom mode, the rest parameters are read-only.
HUE CNT 00~15
SHARPNESS 00~15
SHARP CNT 00~15
BRIGHT 000~255
SATURATION 000~255
HUE 000~255
GAMMA 00~15
IMAGE
BACK
SN 1-4
ON/OFF ON/OFF
DISPLAY ON/OFF
SENSITIVIT
Y
00~99
LC （0-23,0-15） AREA
LOCATION
…
SZ （0-23,0-15）
MOTION
DETECT…
BACK
INDEX 0-7
N/F ON/OFF
CENTRE
SET…
SIZE SET…
COLOR BLUE
PRIVACY
MASK …
BACK
FREEZE ON,OFF
TYPE MOTION DETECT
MODE ON/OFF
ALARM
MODE…
INTERVAL CLOSE，1S-255S
NEXT…
Support PELCO-D/P, DH-SD protocol.
BAUD RATE 1200-9600
ADDRESS 001-254
RS-485…
BACK
OFF
ON… CAMERA ID 1-254
CAMERA ID
BACK
LANGUAGE ENGLISH
MANUFACT
URER
xxx
HARDWARE XXX
SOFTWARE XXX
SYSTEM
INFO…
BACK
PREVIOUS …
ADVANCED
BACK
INDOOR CANCEL,
SAVE ，
DEFAULT ，
RESET
RESTART…
EXIT
FORMAT 720@25… ，

11
720@30…
BACK

12
Appendix Toxic or Hazardous Materials or Elements
Toxic or Hazardous Materials or Elements
Component
Name Pb Hg Cd Cr VI PBB PBDE
Circuit Board
Component ○○○○○○
Device
Construction
Material
○
○○○○○
Wire and Cable ○ ○○○○○
Packing
Components ○○○○○○
Accessories ○○○○○○
O: Indicates that the concentration of the hazardous substance in all homogeneous materials
in the parts is below the relevant threshold of the SJ/T11363-2006 standard.
X: Indicates that the concentration of the hazardous substance of at least one of all
homogeneous materials in the parts is above the relevant threshold of the SJ/T11363-2006
standard. During the environmental-friendly use period (EFUP) period, the toxic or hazardous
substance or elements contained in products will not leak or mutate so that the use of these
(substances or elements) will not result in any severe environmental pollution, any bodily injury
or damage to any assets. The consumer is not authorized to process such kind of substances
or elements, please return to the corresponding local authorities to process according to your
local government statutes.
Note
•This manual is for reference only. Slight difference may be found in the user
interface.
•All the designs and software here are subject to change without prior written
notice.
•All trademarks and registered trademarks mentioned are the properties of their
respective owners.
•If there is any uncertainty or controversy, please refer to the final explanation of
us.
•Please visit our website or contact your local service engineer for more
information.