Daikin DRC036 User manual

Description
These installation instructions supplement the electric heater kits
for installation in the following models:
DRC036, DRC048, DRC060, DRC072
DRH036, DRH048, DRH060, DRH072
DBC036, DBC048, DBC060, DBC072
DBH036, DBH048, DBH060, DBH072
These instructions should be used only as a supplement to
installation instructions IOD-1032 for DRC and DRH models,
or IOD-1043 for DBC and DBH models. If the heater kit is
installed on a unit with DDC controls, reference the DDC user
manual for controller conguration instructions. The controller
will not control the heater kit unless it is properly congured.
WARNING
HIGH VOLTAGE!
DISCONNECT ALL POWER BEFORE SERVICING OR INSTALLING
THIS UNIT. MULTIPLE POWER SOURCES MAY BE PRESENT. FAILURE
TO DO SO MAY CAUSE PROPERTY DAMAGE, PERSONAL INJURY OR
DEATH.
INSTRUCTIONS
1. Disconnect all power to the unit, both indoor and outdoor.
2. Remove control box door.
3. Remove blower door.
4. Locate heater box. Remove screws holding the heater box cover
in place (Figure 1).
BLOWER DOOR
HEAT BOX
COVER
HORIZONTAL
SUPPLY COVER
Figure 1
Attention Installing Personnel
As a professional installer, you have an obligation to know the prod-
uct better than the customer. This includes all safety precautions
and related items.
Prior to actual installation, thoroughly familiarize yourself with this
Instruction Manual. Pay special attention to all safety warnings.
Often during installation or repair, it is possible to place yourself in a
position which is more hazardous than when the unit is in operation.
Remember, it is your responsibility to install the product safely and to
know it well enough to be able to instruct a customer in its safe use.
Safety is a matter of common sense...a matter of thinking before
acting. Most dealers have a list of specic good safety practices...
follow them.
The precautions listed in this Installation Manual are intended as
supplemental to existing practices. However, if there is a direct
conict between existing practices and the content of this manual,
the precautions listed here take precedence.
SAFETY CONSIDERATIONS
The following symbols and labels are used throughout this manual
to indicate immediate or potential safety hazards. It is the owner’s
and installer’s responsibility to read and comply with all safety
information and instructions accompanying these symbols. Failure
to heed safety information increases the risk of personal injury,
property damage, and/or product damage.
ELECTRIC HEAT KITS EHXD, EHXB,
EHSD AnD EHSB foR
3-6 Ton LIGHT CoMMERCIALRoof ToP UnITS
MoDELS: DRC, DRH, DBC AnD DBH
InSTALLATIon InSTRUCTIonS
© 2019
19001 Kermier Rd., Waller, TX 77484
www.daikincomfort.com
P/N: IOD-7100A Date: December 2019
O
NLY
PERSONNEL THAT
HAVE
BEEN
TRAINED TO
INSTALL ,
ADJUST , SERVICE
OR
REPAIR (
HEREINAFTER , “ SERVICE
”) THE EQUIPMENT
SPECIFIED
IN THIS
MANUAL
SHOULD
SERVICE THE
EQUIPMENT . T HE MANUFACTURER WILL
NOT
BE
RESPONSIBLE
FOR
ANY
INJURY
OR
PROPERTY
DAMAGE
ARISING
FROM
IMPROPER SERVICE OR SERVICE PROCEDURES . I F YOU SERVICE THIS UNIT
, YOU
ASSUME RESPONSIBILITY FOR ANY INJURY OR PROPERTY DAMAGE WHICH MAY
RESULT
. I N ADDITION
, IN JURISDICTIONS THAT REQUIRE
ONE OR
MORE
LICENSES
TO SERVICE THE EQUIPMENT SPECIFIED
IN THIS MANUAL , ONLY
LICENSED
PERSONNEL SHOULD SERVICE THE
EQUIPMENT . I MPROPER
INSTALLATION , ADJUSTMENT
, SERVICING
OR REPAIR
OF
THE
EQUIPMENT
SPECIFIED IN
THIS MANUAL , OR
ATTEMPTING TO INSTALL , ADJUST ,
SERVICE OR
REPAIR
THE EQUIPMENT SPECIFIED IN
THIS MANUAL WITHOUT PROPER
TRAINING MAY RESULT IN PRODUCT DAMAGE , PROPERTY
DAMAGE , PERSONAL
INJURY OR DEATH .
WARNING
PROP 65 WARNING
FOR CALIFORNIA CONSUMERS
Cancer and Reproductive Harm -
www.P65Warnings.ca.gov
0140M00517-A
All manuals and user guides at all-guides.com

2
ELECTRIC HEATER KIT
ELECTRIC
PANEL PART
HEATING
ELEMENT PART
Figure 2
Wires and some components are not shown
5. Install heating element part of the heater kit (Figure 2) in the
heater box using screws from heater box cover. Ensure the
elements are positioned in the retaining bracket as shown in
Figure 3. It may be necessary to remove the horizontal supply
cover to observe the bracket. The heater box cover can be
discarded.
6. Install electric panel part of the kit to the left side of the heater
box using 3 screws supplied with this IO (Figure 4).
Figure 3
7. Connect power to kit.
• Remove power cable from the box.
• Connect wire leads to the line side of the power block on the
heater kit’s electrical panel. Connect one wire lead per pole.
• Route all leads through the blower deck and into the control box
as shown in Figure 4.
• Connect wire leads to the load side of the power block in the
unit’s control box. Connect one wire lead per pole.
NOTE: Single phase kits will only have 2 lugs (L1 and L2).
Figure 4
8. Locate 9-pin plug in unit.
9. Connect the plug to the mating 9-pin plug attached to heater kit
(Figure 4).
10. For EHSD and EHSB models, verify that the SCR step
controlboard DIP switch settings match the wiring diagram
provided with the heater kit.
11. Install blower door and horizontal supply cover if it was removed.
12. Set up a required airow - CFM for your unit with electic heater by
selecting a proper speed tap. For details see Air Flow Adjustment
chapter in IOD-1032 for DRC and DRH models or in IOD-1043
for DBC and DBG models.
• Refer to Air Flow for Electric Heat table in this document to
identify minimum required CFM for your unit with specic heater
model.
• Refer to Appendix A - Blower Performance Tables for speed tap
selection in IOD-1032 for DRC and DRH models or in IOD-1043
for DBC and DBH models.
13. Close control box door.
14. Reconnect power to the unit.
15. Test unit to ensure it is functioning properly.
All manuals and user guides at all-guides.com

3
UNITS
HEATER KIT
MODEL NUMBER
kW
MINIMUM
SCFM
EH**-*S05 5
EH**-*S10 10
EH**-*S15 15
EH**-*S05 5
EH**-*S10 10
EH**-*S15 15
EH**-*S18 18
EH**-*S20 20
EH**-*S05 5
EH**-*S10 10
EH**-*S15 15
EH**-*S18 18
EH**-*S20 20
EH**-*S05 5
EH**-*S10 10
EH**-*S15 15
EH**-*S18 18
EH**-*S20 20
EH**-*S30 30
EH**-*S31 30
1950
AIR FLOW FOR ELECTRIC HEAT
DRC060, DRH060,
DBC060, DBH060
DRC036, DRH036,
DBC036, DBH036
DRC048, DRH048,
DBC048, DBH048
975
1300
1625
DRC072, DRH072,
DBC072, DBH072
EH X D - 3 S 15
1 2 3 - 4 5 6, 7
Electric Heater
Heater Type
XStaged
SSCR (modulating)
Drive System
BBelt Drive
DDirect Drive
Voltage
1208-230/1/60 Single phase 60 Hz
3208-230/3/60
Three phase 60 Hz
4460/3/60
Three phase 60 Hz
7575/3/60
Three phase 60 Hz
Chassis
SSmall
MMedium
LLarge
Kilowatt
55 KW HIGH AND STANDARD STATIC
10
15
18
20
30
31
18 KW HIGH AND STANDARD STATIC
20 KW HIGH AND STANDARD STATIC
30 KW HIGH STATIC
30 KW STANDARD STATIC
HEATER KIT MODEL NUMBER NOMENCLATURE
10 KW HIGH AND STANDARD STATIC
15 KW HIGH AND STANDARD STATIC
All manuals and user guides at all-guides.com

4
NOTE: SPECIFICATIONS AND PERFORMANCE DATA LISTED HEREIN ARE SUBJECT TO CHANGE WITHOUT NOTICE
Quality Makes the Difference!
All of our systems are designed and manufactured with the same high quality standards regardless of size or efciency. We have designed
these units to signicantly reduce the most frequent causes of product failure. They are simple to service and forgiving to operate. We use qual-
ity materials and components. Finally, every unit is run tested before it leaves the factory. That’s why we know. . .There’s No Better Quality.
Visit our website at www.daikincomfort.com for information on:
• Products
• Warranties
• Customer Services
• Parts
• Contractor Program and Training
• Financing Options
© 2019
CUSTOMER FEEDBACK
Daikin is very interested in all product comments.
Please ll out the feedback form on the following link:
https://daikincomfort.com/contact-us
You can also scan the QR code on the right to be directed to the feedback page.
All manuals and user guides at all-guides.com