Daktronics BA-2000 Series User manual

201 Daktronics Drive PO Box 5128 Brookings, SD 57006-5128
Tel: 1-800-DAKTRONICS (1-800-325-8766) Fax: [phone]
Web: www.daktronics.com Email: [email protected]
BA-2000 Series
LED Baseball Scoreboards
Display Manual
ED-16961 Rev 4 –19 November 2010
Models
BA-2001
BA-2002
BA-2008
BA-2009
BA-2018

ED-16961
Product 1192
Rev 4 –19 November 2010
DAKTRONICS, INC.
Copyright 2003-2010
All rights reserved. While every precaution has been taken in the preparation of this manual, the publisher
assumes no responsibility for errors or omissions. No part of this book covered by the copyrights hereon may be
reproduced or copied in any form or by any means –graphic, electronic, or mechanical, including photocopying,
taping, or information storage and retrieval systems –without written permission of the publisher.
All Sport®and PanaView®are trademarks of Daktronics, Inc. Other trademarks used in this manual are the property of their
respective owners.
Please fill in the information below to use for reference when calling Daktronics for assistance.
Display Serial No. _______________________________________________________
Display Model No._______________________________________________________
Date Installed___________________________________________________________

Table of Contents i
Table of Contents
Section 1: Introduction ............................................................................................................................1
1.1 Resources..................................................................................................................................1
1.2 Daktronics Nomenclature ......................................................................................................2
1.3 Model Number ........................................................................................................................3
1.4 Scoreboard Controllers...........................................................................................................3
1.5 Product Safety Approval........................................................................................................3
Section 2: Specifications..........................................................................................................................5
Section 3: Mechanical Installation ........................................................................................................7
3.1 Footings & Beams....................................................................................................................7
3.2 Lifting the Scoreboard ............................................................................................................7
3.3 Scoreboard Mounting.............................................................................................................8
Clamping to Verticals......................................................................................................9
Welding to Horizontals.................................................................................................10
3.4 Ad Panel Mounting...............................................................................................................12
3.5 Scoreboard Protective Devices ............................................................................................13
Section 4: Electrical Installation ..........................................................................................................15
4.1 Installation Overview ...........................................................................................................15
4.2 Power......................................................................................................................................16
Grounding.......................................................................................................................17
Connection ......................................................................................................................17
4.3 Power-On Self-Test (POST) .................................................................................................19
Radio Settings.................................................................................................................19
4.4 Signal Connection .................................................................................................................19
Fiber Optic ......................................................................................................................20
Multiple Driver Connections........................................................................................20
4.5 Power/Signal Connections Between Sections...................................................................20
4.6 Lightning Protection .............................................................................................................20
Section 5: Scoreboard Troubleshooting .............................................................................................21
5.1 Troubleshooting Table..........................................................................................................21
5.2 Component Access................................................................................................................23
5.3 Component Locations...........................................................................................................24
5.4 Replacing Digits ....................................................................................................................24
5.5 Replacing Digit Segments ....................................................................................................25
5.6 Replacing Colons, Decimals & Indicators..........................................................................25
5.7 Power Supplies......................................................................................................................25
Replacing a Power Supply............................................................................................25
5.8 LED Drivers ...........................................................................................................................26
Replacing a Driver .........................................................................................................27
Setting the Driver Address ...........................................................................................28
Multiple Drivers.............................................................................................................28
5.9 Radio Connections ................................................................................................................28
Radio Interference..........................................................................................................29
5.10 Segmentation and Digit Designation..................................................................................31
5.11 Schematics..............................................................................................................................31
5.12 Replacement Parts.................................................................................................................31

ii Table of Contents
5.13 Daktronics Exchange and Repair & Return Programs.....................................................32
Exchange Program .........................................................................................................32
Repair & Return Program .............................................................................................33
Daktronics Warranty and Limitation of Liability ......................................................34
Section 6: TNMC Troubleshooting & Maintenance –Models BA-2001/2002/2008/2009 ...........35
6.1 Team Name Message Center System Overview ...............................................................35
6.2 Initialization Information at Startup...................................................................................35
6.3 TNMC Troubleshooting Table.............................................................................................36
6.4 Power & Signal Summary ....................................................................................................37
6.5 Component Locations & Access..........................................................................................38
For TNMCs Built Before September 2009 ...................................................................39
Front Access....................................................................................................................39
Rear Access .....................................................................................................................40
6.6 TNMC Drivers .......................................................................................................................40
Diagnostic LEDs.............................................................................................................42
Replacing a Driver .........................................................................................................42
6.7 Modules..................................................................................................................................42
Replacing Modules ........................................................................................................42
Weather-stripping..........................................................................................................43
6.8 Power Supplies ......................................................................................................................44
Replacing a Power Supply............................................................................................44
6.9 TNMC Maintenance .............................................................................................................44
6.10 Replacement Parts List .........................................................................................................45
For TNMCs Built Before September 2009...................................................................46
Section 7: TNMC Troubleshooting & Maintenance –Model BA-2018 ........................................47
7.1 Team Name Message Center System Overview ...............................................................47
7.2 Initialization Information at Startup...................................................................................47
7.3 TNMC Troubleshooting Table.............................................................................................48
7.4 Power & Signal Summary ....................................................................................................49
7.5 Component Locations & Access..........................................................................................49
Front Access....................................................................................................................50
Rear Access .....................................................................................................................50
7.6 TNMC Drivers .......................................................................................................................51
Diagnostic LEDs.............................................................................................................51
Replacing a Driver .........................................................................................................51
7.7 Modules..................................................................................................................................52
Replacing Modules ........................................................................................................52
7.8 Power Supplies ......................................................................................................................53
Replacing a Power Supply............................................................................................53
7.9 TNMC Maintenance .............................................................................................................53
7.10 Replacement Parts List .........................................................................................................53
Section 8: Additional Scoreboard Options ........................................................................................55
8.1 Radio Control.........................................................................................................................55
8.2 Changeable Caption Kits......................................................................................................55
Appendix A: Reference Drawings ............................................................................................................57
Appendix B: Daktronics Warranty and Limitation of Liability ..........................................................59

Introduction 1
Section 1: Introduction
This manual explains the installation of Daktronics BA-2000 series LED baseball scoreboards and
provides details for maintenance and troubleshooting. For additional information regarding the
safety, installation, operation, or service of this system, refer to the telephone numbers listed in
Section 5.13. This manual is not specific to a particular installation.
Important Safeguards:
Please read and understand all instructions before beginning the installation process.
Do not drop control equipment or allow it to get wet.
Do not disassemble control equipment or electronic controls of the display; failure to
follow this safeguard will make the warranty null and void.
Disconnect display power when not in use or when servicing.
Disconnect display power before servicing power supplies to avoid electrical shock.
Power supplies run on high voltage and may cause physical injury if touched while
powered.
Do not modify the scoreboard structure or attach any panels or coverings to the
scoreboard without the express written consent of Daktronics, Inc.
Project-specific information takes precedence over any other general information found in
this manual.
1.1 Resources
Figure 1 illustrates a Daktronics drawing
label. The drawing number is located in the
lower-right corner of a drawing. This
manual refers to drawings by listing the last
set of digits and the letter preceding them.
In the example, the drawing would be
referred to as Drawing C-325405.
Reference Drawing:
System Riser Diagram ...........................................................................Drawing C-325405
Daktronics identifies manuals by the DD or ED number located on the cover page of each
manual. For example, this manual would be referred to as ED-16961.
Figure 1: Daktronics Drawing Label

2 Introduction
1.2 Daktronics Nomenclature
Serial and model numbers can be found on the ID label on the display as shown in Figure 2.
Please list the model number, display serial number, and the date this display became
operational in the blanks provided on the second page of this manual. When calling
Daktronics customer service, please have this information available to ensure the request is
serviced as quickly as possible.
Most components within this display carry a white label that lists the part number of the unit.
If a component is not found in the Replacement Parts List in Section 5.12, use the label to
order a replacement. Figure 3 illustrates a typical label. The part number is in bold.
Main Component Labels
Part Type
Part Number
Individual circuit board
0P-XXXX-XXXX
Assembly; a collection of circuit boards
0A-XXXX-XXXX
Wire or cable
W-XXXX
Fuse
F-XXXX
Transformer
T-XXXX
Metal part
M-XXX
Fabricated metal assembly
0S-XXXXXX
Specially ordered part
PR-XXXXX-X
Accessory Labels
Component
Label
Termination block for power
or signal cable
TBXX
Grounding point
EXX
Power or signal jack
JXX
Power or signal plug for the
opposite jack
PXX
Following the Replacement Parts List is the Daktronics Exchange Policy and the Repair &
Return Program. Refer to these instructions if replacing or repairing any display component.
Figure 2: Scoreboard ID Label
Figure 3: Typical Label

Introduction 3
1.3 Model Number
Daktronics scoreboards are differentiated by their model numbers and two-letter prefixes for
each sport. Most Daktronics scoreboards also carry a two-number suffix that refers to the type
of power supply and digit color. Refer to the following tables:
BA
Baseball
-11
120 V, with red digits
-21
120 V, with amber digits
-12
240 V, with red digits
-22
240 V, with amber digits
1.4 Scoreboard Controllers
Daktronics outdoor scoreboards are designed for use with the All Sport®5000 series control
consoles. This console uses keyboard overlays (sport inserts) to control numerous sports and
scoreboard models. Refer to the following manual for operating instructions:
All Sport 5000 Series Control Console Operation Manual (ED-11976)
This control console manual is available online at www.daktronics.com/manuals.
1.5 Product Safety Approval
Daktronics outdoor scoreboards are ETL listed and tested to CSA standard for outdoor use.
Contact Daktronics with any questions regarding testing procedures.

Specifications 5
Section 2: Specifications
The chart on the following pages details all of the mechanical specifications, circuit specifications and
power requirements for each display in this manual. Models are listed in alphanumeric order.
Notes:
1) All displays require a 120 V AC, 15 A circuit. Displays with a 240 V A C power
requirement are also available.
2) Signal wire must be minimum of 22 AWG with shield. Daktronics recommends W-1234.
3) TNMC LEDs are the same color as the LED digits on the scoreboard.
Model &
Options
Number of
Sections
Dimensions:
Height (H), Width (W), Depth (D)
Weight
Watts
Amps
120 / 240 V AC
Driver #
& Address
BA-2001
1 Total
H 7'-0", W 28'-0", D 8"
(2134 mm, 8534 mm, 203 mm)
640 lb
(291 kg)
900 W
7.5 A / 3.75 A
A1 67
A2 68
A3 69
w/ TNMC
(same)
(same)
720 lb
(327 kg)
1200 W
10 A / 5 A
TNMC 221
BA-2002
2 Total
Top
Bottom
H 9'-4", W 36'-0", D 8"
(2845 mm, 10973 mm, 203 mm)
H 4'-0", W 36'-0", D 8"
(1219 mm, 10973 mm, 203 mm)
H 5'-4", W 36'-0", D 8"
(1626 mm, 10973 mm, 203 mm)
1116 lb
(506 kg)
900 W
7.5 A / 3.75 A
A1 67
A2 68
A3 69
w/ TNMC
(same)
(same)
1236 lb
(561 kg)
1200 W
10 A / 5 A
TNMC 221
BA-2008
1 Total
H 7'-0", W 28'-0", D 8"
(2134 mm, 8534 mm, 203 mm)
640 lb
(291 kg)
1200 W
10 A / 5 A
A1 67
A2 68
A3 69
A4 11
w/ TNMC
(same)
(same)
720 lb
(327 kg)
1500 W
12.5 A / 6.25 A
TNMC 221
BA-2009
2 Total
Top
Bottom
H 9'-4", W 36'-0", D 8"
(2845 mm, 10973 mm, 203 mm)
H 4'-0", W 36'-0", D 8"
(1219 mm, 10973 mm, 203 mm)
H 5'-4", W 36'-0", D 8"
(1626 mm, 10973 mm, 203 mm)
1236 lb
(561 kg)
1200 W
10 A / 5 A
A1 67
A2 68
A3 69
A4 11
w/ TNMC
(same)
(same)
1356 lb
(615 kg)
1500 W
12.5 A / 6.25 A
TNMC 221

6 Specifications
Model &
Options
Number of
Sections
Dimensions:
Height (H), Width (W), Depth (D)
Weight
Watts
Amps
120 / 240 V AC
Driver #
& Address
BA-2018
4 Total
Top Left
Bottom Left
Top Right
Bottom
Right
H 13'-0", W 42'-0", D 8"
(3962 mm, 12802 mm, 203 mm)
H 7'-6", W 23'-0", D 8"
(2438 mm, 7010 mm, 203 mm)
H 5'-6", W 23-0", D 8"
(2134 mm, 7010 mm, 203 mm)
H 7'-6", W 19'-0", D 8"
(2438 mm, 5791 mm, 203 mm)
H 5'-6", W 19'-0", D 8"
(2134 mm, 5791 mm, 203 mm)
2530 lb
(1148 kg)
1200 W
10 A / 5 A
A1 66
A2 65
A3 64
A4 01
w/ TNMC
(same)
(same)
2730 lb
(1238 kg)
1600 W
13.5 A / 6.7 A
TNMC 221

Mechanical Installation 7
Section 3: Mechanical Installation
Mechanical installation consists of installing concrete footing and steel beams and mounting the
scoreboard and accompanying ad panels to the beams.
3.1 Footings & Beams
The installation specification drawings in Appendix A show the recommended number of
beams and spacing between them for each scoreboard in this manual. The drawings also
indicate the size of beams required to support the scoreboard at different heights and at
various wind speeds. Use the following table to determine which drawings provide the
installation specifications for each model:
Models
Drawing Title
Number
BA-2001, BA-2008
28' Width Scoreboard Installation Specs
A-316971
BA-2002, BA-2009
36' Width Scoreboard Installation Specs
A-317277
BA-2018
Shop DWG, BA-2018, Pole Mount
B-223556
Shop DWG, BA-2018, Horiz Tubes
B-222672
The column and footing size dimensions are to assist with estimating installation costs. They
are estimates only and are not intended for actual construction purposes. Be sure that the
installation complies with local building codes and is suitable for the particular soil and wind
conditions. The columns, footings, and all connection details must be designed and certified
by a professional engineer licensed to practice in the state of the scoreboard installation.
Note: Daktronics does not assume any liability for any installation derived from the
information provided in this manual or installations designed and installed by others.
3.2 Lifting the Scoreboard
Larger scoreboard sections and message centers are shipped equipped with eyebolts used to
lift them. The eyebolts are located along the top of the cabinet for each scoreboard or
scoreboard section. Daktronics scoreboards use 1/2" and 5/8" shoulder-type eyebolts mounted
to a 1/8" aluminum plate or steel nut plate.
Daktronics strongly recommends using a spreader bar, or lifting bar, to lift the display.
Spreader bars ensure the force on the eyebolts remains straight up, minimizing lifting stress.
Figure 4: Lifting Methods

8 Mechanical Installation
Figure 4 illustrates the preferred scoreboard lifting method on the left and an acceptable
alternative lifting method on the right. When lifting the display:
Use a spreader bar if possible.
Use every lifting point provided.
Cables and chains attached to the eyebolts and directly to
a center lifting point, as shown in the right-hand example
in Figure 4, can create a dangerous lateral force on the
eyebolts and may cause the eyebolts to fail. The smaller
the angle between the cable and the top of the display, the
lighter the sign must be to safely lift it. If this method
must be used, ensure a minimum angle between the chain
and scoreboard of at least 45 degrees.
Do NOT attempt to lift the display if the angle is less than
45 degrees. Exceeding load angles or weight limits could
cause the bolts in the scoreboard cabinet to buckle,
resulting in serious damage to the scoreboard or injury to
personnel. Also, loads should be applied directly in the
plane of the eyebolt as shown in Figure 5.
Note: Daktronics assumes no liability for damages resulting from incorrect setup or
lifting methods. Eyebolts are intended for lifting only. Do not attempt to permanently
support the display by the eyebolts.
If installers remove the eyebolts, plug the holes with bolts and the rubber washers that are
used with the eyebolts. Apply silicone or another waterproof sealant to the eyebolt openings.
Also inspect the top and sides of the display for any other holes or openings that may allow
moisture to enter the display and plug and seal those openings.
3.3 Scoreboard Mounting
In typical multi-section installations, the lower scoreboard is installed first and secured to the
support beams. The upper section is then placed atop or above the lower section and attached
to the beams. There are cables extending from the top of the lower section. Guide these cables
into the hole in the bottom of the upper section for later connection. Refer to Section 4.5 for
more information on the power/signal connections between sections.
Scoreboard models in this manual are typically mounted in one of two ways:
1) clamped to vertical beams using mounting angles and long, threaded rods or
2) permanently welded to tubular horizontal supports.
Figure 5: Eyebolt Plane Load

Mechanical Installation 9
Clamping to Verticals
An inverted channel mounting installation uses C-channels; clip angles; 1/2-13" threaded
rods; and 1/2" square nuts, hex nuts, lock washers, and optional spacers. Refer to Figure 6 and
Drawing A-55101 in Appendix A.
Mount the scoreboard as follows:
1. Place the C-channel against the upper and lower rear flanges of the scoreboard.
2. Use the width of the beam to determine the appropriate hole combination to use for
the bolts. The bolts should be kept as close to the beam as possible.
3. With the C-channel as a template, use a 9/16" bit to drill holes in the upper and lower
rear flanges of the scoreboard cabinet where the bolts will pass through.
4. Place the 1/2" square nuts inside the C-channel and thread the 1/2-13" rods through
the C-channel, rear flange of the scoreboard cabinet, and spacer (if used).
5. Lift the scoreboard into position with the bolts still in place. Position the scoreboard
at the front of the beams with the threaded rods extending from the rear flanges.
6. With the threaded rod straddling the beams, place mounting angles over each pair of
bolts and secure with 1/2" lock washers and hex nuts.
7. Make final adjustments in the positioning of the scoreboard.
8. Make sure that the threaded rods are perpendicular to the scoreboard, and tighten all
of the 1/2" hex nuts.
Figure 6: C-channel Mounting Method, Side View

10 Mechanical Installation
Welding to Horizontals
Steel clip angles are first bolted to the back of each scoreboard section. These clip angles are
then welded on three sides to a horizontal tube, which itself has been welded to the support
beams. Refer to the sections below for suggested horizontal tube spacing.
Models BA-2001 & BA-2008
Figure 7 shows the spacing of the horizontal tubes for BA-2001
and BA-2008 single-section scoreboards. The horizontal tubing
must have a vertical dimension (height) of 4" (102 mm).
The bottom of the first horizontal tube is level with the bottom of
the scoreboard and is considered the zero mark for measuring
the other horizontal tube. The second horizontal tube is at 84"
(2134 mm), including the height of the tube, and will be flush
with the top of the scoreboard. Spacing may vary depending on
the installation. Refer to any project-specific shop drawings for
exact tube and clip angle spacing.
Models BA-2002 & BA-2009
Figure 8 shows the spacing of the horizontal tubes for
BA-2002 and BA-2009 multi-section scoreboards.
The horizontal tubing must have a vertical dimension
(height) of 4" (102 mm). The bottom of the first horizontal
tube is level with the bottom of the scoreboard and is
considered the zero mark for measuring the other two
horizontal tubes. The middle horizontal tube is at 66.2"
(1681 mm), including the height of the tube. The top
horizontal tube is at 112.4" (2855 mm), including the
height of the tube, and will be flush with the top of the
scoreboard. Spacing may vary depending on the
installation. Refer to any project-specific shop drawings
for exact tube and clip angle spacing.
Figure 7: Tube Spacing,
BA-2001 & BA-2008
Figure 8: Tube Spacing,
BA-2002 & BA-2009

Mechanical Installation 11
Model BA-2018
Figure 9 shows the spacing of the horizontal
tubes for BA-2018 scoreboards. The horizontal
tubing must have a vertical dimension (height)
of 4" (102 mm). The bottom of the first
horizontal tube is level with the bottom of the
scoreboard and is considered the zero mark for
measuring the other two horizontal tubes.
The middle horizontal tube is at 68" (1727 mm),
including the height of the tube. The top
horizontal tube is at 156" (3962 mm), including
the height of the tube, and will be flush with the
top of the scoreboard. Refer to Drawing B-
238121 in Appendix A or project-specific shop
drawings for exact tube and clip angle spacing.
Figure 10 and Drawing A-83301 in Appendix A illustrate the mounting of the display to
horizontal tubing.
1. Visually check the display structure before beginning the installation process.
Ensure that the structure will provide a straight and square mounting frame for
the scoreboard/display.
Check to ensure the mounting frame will not give way at unsupported points
after the scoreboard/display is mounted. If any problems are noted, take
corrective action immediately.
2. Bolt the clip angles to the rear of the scoreboard sections with ½" hardware.
Refer to project-specific shop drawings for exact locations of the clip angles.
3. Lift the display section into position. Refer to Section 3.2.
4. Adjust the clip angles as needed so that they are firmly against the horizontal tube.
During the installation of the first section, carefully monitor the horizontal and
vertical straightness of the display. If the mounting structure does not provide a
straight or square mounting surface, it will be necessary to place shims between the
display section and the mounting surface to ensure straightness.
5. Weld the three edges of each clip angle that are in contact with the horizontal tube.
Figure 9: Beam Spacing, BA-2018

12 Mechanical Installation
3.4 Ad Panel Mounting
The installation uses C-channels; clip angles; 1/2-13" threaded rods; and 1/2" square nuts, hex
nuts, lock washers, and optional spacers similar to the clamping mounting method above.
Refer to Figure 11 and Drawing A-52187 in Appendix A.
Figure 10:Scoreboard Mounting Detail, Side View
Figure 11:Ad Panel Mounting with C-channel, Side View

Mechanical Installation 13
Mount the ad panel(s) as follows:
1. Use the width of the beam to determine which hole combination to use for the bolts.
Be sure to keep the bolts as close to the beam as possible.
2. Using the clip angle as a template, use a 9/16" bit to drill holes in the upper and lower
rear flange of the ad panel where the C-channel supports will be placed.
3. Position the C-channel inside the ad panel cabinet along the upper and lower rear
flanges as shown in Figure 11.
4. Place 1/2" square nuts inside the channel and thread the 1/2-13" rods through the
C-channel, rear flange of the ad panel, and spacer (if used).
5. Lift the ad panel into position with the rods still in place.
6. With the threaded rod straddling the beams, place mounting angles over the ends of
each pair of bolts and secure with 1/2" lock washers and hex nuts.
7. Make final adjustments in the positioning of the ad panel.
8. Make sure that the threaded rods are perpendicular to the ad panel, and tighten all of
the 1/2" hex nuts.
Some ad panels have back sheets that must be removed before the display can be installed.
After marking and drilling holes in the upper and lower rear flanges of the ad panel, remove
the back sheets above and below the hole locations. Position the C-channel inside the cabinet
and attach the square nuts to the threaded rods as described above. Be sure to replace the
back sheets after placing the square nuts inside the channel and threading the rods through
the holes in both the upper and lower rear flanges.
3.5 Scoreboard Protective Devices
Daktronics makes optional protective devices, including screens and netting, to help prevent
damage to the scoreboard due to normal ball impacts.
Note: Some users install devices to protect the scoreboard from projectiles. Scoreboard
protection devices not provided by Daktronics must be approved by Daktronics prior to
installation. Failure to follow this approval procedure will void the scoreboard warranty.