Daktronics BA-515 User manual

Single-Section Outdoor
Incandescent Scoreboards
Installation, Maintenance,
and Specifications Manual
ED11974
All Sport®is a registered trademark of Daktronics, Inc
Deoxit

and Cailube

are trademarks of their respective manufacturers.
MODEL NUMBERS
BA-515 BA-718 CT-2001 MS-915 MS-2006 SO-2008
BA-518 BA-1018 CT-2002 MS-918 MS-2011 TI-218
BA-618 BA-2003 FB-824 MS-2002 SO-824 TI-418
BA-624 BA-2004 FB-2340 MS-2004 SO-918 TI-2003
ED11974
Product 1091
Rev 9 – 13 August 2002
Copyright © 2002 Daktronics, Inc.
All rights reserved. While every precaution has been taken in the
preparation of this manual, the publisher assumes no responsibility for errors
or omissions. No part of this book covered by the copyrights hereon may be
reproduced or copied in any form or by any means – graphic, electronic
or mechanical, including photocopying, taping, or information storage
and retrieval systems – without written permission of the publisher.
PO Box 5128 331 32nd Ave Brookings SD 57006
Note: Please fill in the information below for
your display, and use it as a reference when
calling Daktronics for assistance.
Serial No. ___________________________
Model No.___________________________
Date Installed ________________________
Tel [phone] or 877-605-1115 Fax [phone]
www.daktronics.com e-mail: hel[email protected]

Table of Contents
Section 1: Introduction..................................................................................................1-1
1.1 How To Use This Manual ..........................................................................................1-1
1.2 Product Safety Approval ............................................................................................1-1
1.3 Manual Overview .......................................................................................................1-2
1.4 Daktronics Exchange and Repair and Return Programs ............................................1-2
Section 2: Model Identification.....................................................................................2-1
Section 3: Specifications ..............................................................................................3-1
3.1 Single-Section Scoreboards........................................................................................3-2
3.2 230 Volt Single-Section Scoreboards.........................................................................3-7
Section 4: Component Locations.................................................................................4-1
Section 5: Schematics...................................................................................................5-1
Section 6: Mechanical Installation ...............................................................................6-1
6.1 Footings and Beams ...................................................................................................6-1
6.2 Lifting the Scoreboard................................................................................................6-2
6.3 Scoreboard Mounting.................................................................................................6-3
Method 1 ....................................................................................................................6-3
Method 2 ....................................................................................................................6-4
6.4 Ad Panel Mounting ....................................................................................................6-5
Models BA-515 and BA-518 .....................................................................................6-5
Section 7: Electrical Installation...................................................................................7-1
7.1 Power Requirements...................................................................................................7-1
Grounding...................................................................................................................7-1
Power Installation.......................................................................................................7-2
7.2 Power and Signal Connection ....................................................................................7-3
Section 8: Digit Maintenance and Troubleshooting ...................................................8-1
8.1 Component Access .....................................................................................................8-1
Lamp Driver Access...................................................................................................8-1
Digit Access ...............................................................................................................8-1
8.2 Lamp Replacement.....................................................................................................8-2
8.3 Lamp Drivers..............................................................................................................8-2
8.4 Fuses...........................................................................................................................8-3
8.5 Segmentation ..............................................................................................................8-3
8.6 Power On Self-Test ....................................................................................................8-3
8.7 Lightning Protection...................................................................................................8-4
8.8 Replacement Parts ......................................................................................................8-4
8.9 Troubleshooting .........................................................................................................8-5
Table of Contents
i

Section 9: Team Name Message Centers Maintenance and Troubleshooting ........9-1
9.1 TNMC Schematics..................................................................................................... 9-1
9.2 Service Procedures..................................................................................................... 9-2
Removing a Module................................................................................................... 9-2
Removing a Lampbank.............................................................................................. 9-2
Replacing a Lampbank .............................................................................................. 9-3
Replacing the Module................................................................................................ 9-3
9.3 Lamp Testing and Replacement................................................................................. 9-3
Individual Lamp Replacement................................................................................... 9-4
9.4 Lens Position and Sequence ...................................................................................... 9-4
9.5 Lens/Reflector Assembly Maintenance ..................................................................... 9-4
Weatherstripping Maintenance .................................................................................. 9-4
Louver Maintenance .................................................................................................. 9-5
9.6 Lamp Module Transformer........................................................................................ 9-5
9.7 Fan Filters .................................................................................................................. 9-5
9.8 Filter Removal ........................................................................................................... 9-6
9.9 Fans............................................................................................................................9-6
9.10 Lens Airflow .............................................................................................................. 9-7
9.11 Structural Inspection .................................................................................................. 9-8
9.12 Cleaning the Signal Connectors................................................................................. 9-8
9.13 Troubleshooting......................................................................................................... 9-8
9.14 Replacement Parts List .............................................................................................. 9-9
9.15 TNMC Exchange and Repair and Return Programs................................................ 9-10
Section 10: Scoreboard Options ..................................................................................10-1
10.1 Team Name Captions – Models BA-624, BA-1518 and BA-1524 ......................... 10-1
10.2 Trumpet Horn .......................................................................................................... 10-2
AC Trumpet Horn Installation (Internally Mounted) .............................................. 10-2
DC Trumpet Horn Installation (Externally Mounted) ............................................. 10-2
Appendix A: Reference Drawings................................................................................... A-1
Appendix B: Eyebolts........................................................................................................ B-1
Table of Contents
ii

Section 1: Introduction
1.1 How To Use This Manual
This manual explains the installation of Daktronics Single-Section, Outdoor Incandescent
Scoreboards and provides details for display maintenance. For questions regarding the safety,
installation, operation, or service of this system, please refer to the telephone numbers listed on the
cover page of this manual.
Important Safeguards:
1. Read and understand these instructions before installing the scoreboard.
2. Do not drop the scoreboard control console or allow it to get wet.
3. Properly ground the scoreboard with a grounding electrode at the scoreboard location.
4. Disconnect power when not using the scoreboard.
5. Disconnect power when servicing the scoreboard.
6. Do not modify the scoreboard structure or attach any panels or coverings to the scoreboard
without the express written consent of Daktronics, Inc.
The box at right illustrates the Daktronics
drawing numbering system. Daktronics
identifies individual drawings by the drawing
number (7087-P08A-69945 in Figure 1),
which is located in the lower-right corner of
the drawing. This manual refers to drawings
by their last set of digits and the letter
preceding them. The example would be
Drawing A-69945.
Figure 1: Daktronics Drawing Label
Reference drawings are grouped and inserted in alphanumeric order in Appendix A.
The serial and model number of a Daktronics scoreboard can be found on the ID label, located on the
display. This label will be
similar to the one shown in
Figure 2. When calling
Daktronics Customer
Service, please have this
information available to
ensure that your request
Figure 2: Scoreboard ID Label
is serviced as quickly
as possible.
1
.2 Product Safety Approval
Daktronics outdoor scoreboards are ETL-listed, tested to CSA standards and CE-labeled for outdoor
use. Contact Daktronics with any questions regarding testing procedures.
Introduction
1-1

1.3 Manual Overview
This manual is divided into the following sections:
Section 1: Contains an overview of the manual and explains the Daktronics drawing
numbering system and Daktronics Exchange and Repair and Return
programs.
Section 2: Lists the drawings needed to determine scoreboard model numbers.
Section 3: Contains tables showing all of the mechanical specifications, circuit
specifications, and maximum power requirements for each model.
Section 4: Lists drawings needed to determine the location of scoreboard components.
Section 5: Lists the electrical schematic drawings for each model.
Section 6: Contains information needed for the mechanical installation for each model.
Section 7: Contains information needed for the electrical installation for each model.
Section 8: Contains information needed to service the scoreboards.
Section 9: Contains information needed to service the team name message centers.
Section 10: Contains descriptions and installation instructions for the various scoreboard
options.
Appendices: Contain reference drawings and ED-7244, Eyebolts.
1.4 Daktronics Exchange and Repair and Return Programs
To serve customers’ repair and maintenance needs, Daktronics offers both an Exchange Program and a
Repair and Return Program.
Daktronics’ unique Exchange Program is a quick, economical service for replacing key components in
need of repair. If a component fails, Daktronics sends the customer a reconditioned replacement
within 24 hours. The customer, in turn, sends the failed component to Daktronics. This not only saves
money but also decreases scoreboard downtime. This service is provided to qualified customers who
follow the program guidelines explained below.
Daktronics provides this service to ensure users get the most from their Daktronics products. Please
call the Help Desk – [phone] – if you have questions regarding the Exchange Program or any
other Daktronics service.
When you call the Daktronics Help Desk, a trained service technician will work with you to diagnose
the equipment problem and determine which replacement part to ship. (If, after you make the
exchange, the equipment still has problems, please contact our Help Desk immediately.) If the
replacement part fixes the problem, package the defective part in the same box and wrapping in which
the replacement part arrived, fill out and attach the enclosed UPS shipping document, and RETURN
THE PART TO DAKTRONICS.
For most equipment, you will be invoiced for the replacement part at the time it is shipped. This bill is
due when you receive it.
Daktronics expects immediate return of an exchange part if it does not solve the problem. The
company also reserves the right to refuse equipment that has been damaged due to acts of nature or
causes other than normal wear and tear.
1-2 Introduction

If the defective equipment is not shipped to Daktronics within 30 working days from the invoice date,
it is assumed you are purchasing the replacement part, and you will be invoiced for it. This second
invoice represents the difference between the exchange price and the full purchase price of the
equipment. The balance is due when you receive the second invoice. If you return the exchange
equipment after 30 working days from the invoice date, you will be credited for the amount on the
second invoice, minus a restocking fee.
@To avoid a restocking charge, please return the defective equipment within 30 days from the
invoice date.
Daktronics also offers a repair and return program for items not subject to exchange.
Return Materials Authorization: To return parts for service, contact your local representative prior
to shipment to acquire a Return Materials Authorization (RMA) number. If you have no local
representative, call the Daktronics Help Desk for the RMA. This expedites repair of your component
when it arrives at Daktronics.
Packaging for Return: Package and pad the item well so that it will not be damaged in shipment.
Electronic components such as printed circuit boards should be installed in an enclosure or placed in
an antistatic bag before boxing. Please enclose your name, address, phone number and a clear
description of symptoms.
This is how to reach us:
Mail:Customer Service
Daktronics, Inc.
P.O. Box 5128
331 32nd Avenue
Brookings, SD 57006
Phone:Daktronics Help Desk: 1 [phone] (toll free)
or 1 [phone]
Fax:[phone]
E-mail:[email protected]
Introduction
1-3

Section 2: Model Identification
Use the following drawings to determine your scoreboard model number. The drawings, located in the
Appendix, are inserted in alphanumeric order by drawing number.
Reference Drawings:
Single-Section Scoreboard Models....................................................... Drawing A-124342
Single-Section Scoreboard Models w/TNMC........................................ Drawing A-127262
Single Section Scoreboard Models ....................................................... Drawing A-152945
Model Identification
2-1

Section 3: Specifications
The following tables include all of the mechanical specifications, circuit specifications, and maximum
power requirements for each model in this manual. Models are listed in alphanumeric order.
Section 3.1: Single-Section Scoreboards ....................................................................................3-2
Section 3.2: 230-Volt Single-Section Scoreboards.....................................................................3-5
Specifications
3-1

3.1 Single-Section Scoreboards
Note 1: Signal wires must be a minimum of 22- gauge with shield. Daktronics recommends using W-1234.
Note 2: 120/240 or two lines of 120 V AC from a 120/208 WYE service.
WattageModel Dimensions
(Height, Width,
Depth)
Weight
Uncrated
(Crated)
Digit Size
and Matrix Lamp Maximum
Power
(See Note 2)
Amps per Line
(Single Phase)
Driver Number
and Address
Inning, scores
15" 3x5
(381 mm)
25 W 1905 W 120 V AC 16 A
Inning, scores
15" 4x7
(381 mm)
30 W 3280 W 120 V AC 27 A
BA-515 H3’-0", W6’-0", D11"
(914 mm, 1829 mm,
279 mm)
115 lb
52 kg
(118 lb)
(54 kg)
Ball, Strike,
Out indicators
40 W
A1 61
Inning, scores
18" 3x5
(457 mm)
25 W 1905 W 120 V AC 16 A
Inning, scores
18" 4x7
(457 mm)
25 W 2780 W 120 V AC 24 A
BA-518 H4’-0", W9’-0", D6"
(1219 mm, 2743 mm,
152 mm)
120 lb
55 kg
(152 lb)
(70 kg)
Ball, Strike,
Out indicators
40 W
A1 61
All digits
18" 3x5
(457 mm)
25 W 2110 W 120 V AC 18 A
All digits
18" 4x7
(457 mm)
25 W 3035 W 120 V AC 26 A
BA-618 H5’-0", W14’-0", D6"
(1524 mm, 4267 mm,
152 mm)
250 lb
114 kg
(580 lb)
(263 kg)
Ball, Strike,
Out, H/E
indicators
40 W
A1 61
All digits
24" 4x7
(610 mm)
25 W 3035 W 120 V AC 24 A
BA-624 H6’-0", W16’-0", D6"
(1829 mm, 4877 mm,
152 mm)
375 lb
170 kg
(770 lb)
(350 kg)
Ball, Strike,
Out, H/E
Indicators
40 W
A1 61
Specifications 3-2

WattageModel Dimensions
(Height, Width,
Depth)
Weight
Uncrated
(Crated)
Digit Size
and Matrix Lamp Maximum
Power
(See Note 2)
Amps per Line
(Single Phase)
Driver Number
and Address
Inning, Time,
scores
18" 3x5
(457 mm)
25 W 2555 W 120 V AC 22 A
Inning, Time,
scores
18" 4x7
(457 mm)
25 W 3780 W 120 V AC 32 A
BA-718 H4’-0", W12’-0", D6"
(1219 mm, 3658 mm,
152 mm)
160 lb
73 kg
(490 lb)
(222 kg)
Ball, Strike,
Out indicators
40 W
A1 62
All digits
18" 3x5
(457 mm)
25 W 3050 W 120/240 or
120/208 V AC
L1 15 A
L2 11 A
BA-1018 H6’-0", W14’-0", D6"
(2438 mm, 4877 mm,
152 mm)
270 lb
122 kg
(621 lb)
(281 kg) All digits
18" 4x7
(457 mm)
25 W 4675 W 120/240 or
120/208 V AC
L1 23 A
L2 17 A
A1 12
BA-2003 H4'-6", W10'-0", D8"
(1372 mm, 3048 mm,
203 mm)
250 lb
113 kg
(475 lb)
(215 kg)
All digits
36" 4x7
(914 mm)
40 W 1880 W 120/240 or
120/208 V AC
15 A A1 11
BA-2004 H6'-6", W20'-0", D6"
(2845 mm, 6096 mm,
152 mm)
750 lb
340 kg
(1,425 lb)
(646 kg)
Ball, strike,
out, H/E
18" 3x5
(457 mm)
Scoring
15" 3x5
(381 mm)
25 W 8491 W 120/240 or
120/208 V AC
L1 33 A
L2 38 A
A1 67
A2 68
A3 69
All digits
18" 3x5
(457 mm)
25 W 975 W 120 V AC 15 A
CT-2001 H2’-0", W6’-0", D11"
(610 mm, 1829 mm,
279 mm)
50 lb
23 kg
(83 lb)
(37 kg)
All digits
18" 4x7
(457 mm)
25 W 1500 W 120 V AC 15 A
A1 1
Specifications
3-3

WattageModel Dimensions
(Height, Width,
Depth)
Weight
Uncrated
(Crated)
Digit Size
and Matrix Lamp Maximum
Power
(See Note 2)
Amps per Line
(Single Phase)
Driver Number
and Address
CT-2002 H2’-7", W7’-0", D11"
(610 mm, 2133 mm,
279 mm)
75 lb
34 kg
(125 lb)
(57 kg)
All digits
24" 4x7
(610 mm)
25 W 1500 W 120 V AC 15 A A1 1
All digits
24" 4x7
(610 mm)
25 W
FB-824 H4’-0", W14’-0", D6"
(1219 mm, 4267 mm,
152 mm)
250 lb
114 kg
(560 lb)
(254 kg)
Quarter
indicators
40 W
4160 W 120/240 or
120/208 V AC
L1 18 A
L2 17 A
A1 11
FB-2340
H5'-0", W7'-0", D8"
(1524 mm, 2134 mm,
203 mm)
135 lb
61 kg
(220 lb)
(100 kg)
All digits
18" 4x7
(457 mm)
25 W 3000 W 120/240 or
120/20 V AC
L1 12.5 A
L2 12.5 A
A1 2
MS-915 H4’-0", W8’-0", D11"
(1219 mm, 2438 mm,
279 mm)
110 lb
50 kg
(185 lb)
(84 kg)
All digits
15" 3x5
(381 mm)
25 W 2925 W 120/240 or
120/208 V AC
L1 11 A
L2 14 A
A1 11
Clock, scores
18" 3x5
(457 mm)
Inning
15" 3x5
(381 mm)
25 W 3285 W 120/240 or
120/208 V AC
L1 11 A
L2 17 A
Clock, scores
18" 4x7
(457 mm)
Inning
15" 4x7
(381 mm)
25 W 4960 W 120/240 or
120/208 V AC
L1 17 A
L2 24 A
MS-918 H5’-0", W14’-0", D6"
(1524 mm, 4267 mm,
152 mm)
275 lb
125 kg
(640 lb)
(290 kg)
Ball, Strike,
Out indicators
40 W
A1 11
Specifications 3-4

WattageModel Dimensions
(Height, Width,
Depth)
Weight
Uncrated
(Crated)
Digit Size
and Matrix Lamp Maximum
Power
(See Note 2)
Amps per Line
(Single Phase)
Driver Number
and Address
Clock, scores
24" 4x7
(610 mm)
25 W
MS-2002 H4’-6", W16’-0", D6"
(1372 mm, 4877 mm,
152 mm)
250 lb
114 kg
(715 lb)
(324 kg)
Period
18" 3x5
(457 mm)
25 W
4325 W 120/240 or
120/208 V AC
L1 17 A
L2 20 A
A1 11
MS-2002
w/TNMC
H4’-6", W16’-0", D6"
(1372 mm, 4877 mm,
152 mm)
425 lb
193 kg
(740 lb)
(336 kg)
Period
18" 3x5
(457 mm)
25 W
6245 W 120/240 or
120/208 V AC
L1 25 A
L2 28 A
A1 11
All digits
18" 3x5
(457 mm)
25 W 10 000 W 120/240 or
120/208 V
AC
L1 28 A
L2 28 A
MS-2004 H5’-0", W18’-0", D6"
(1524 mm, 5486 mm,
152 mm)
375 lb
170 kg
(770 lb)
(350 kg)
All digits
18" 4x7
(457 mm)
25 W 10 000 W 120/240 or
120/208 V AC
L1 42 A
L2 42 A
A1 74
A2 75
MS-2006
w/TNMC
H7'-0", W25'-0", D6"
(2134 mm, 7620 mm,
152 mm)
500 lb
227 kg
(850 lb)
(386 kg)
Clock, scores
30" 4x7
(762 mm)
Period
24" 4x7
(610 mm)
25 W 10 080 W 120/240 or
120/208 V AC
L1 25 A
L2 28 A
A1 11
MS-2011
w/TNMC
H4'-6", W20'-0", D6"
(1372 mm, 6096 mm,
152 mm)
475 lb
215 kg
(903 lb)
(410 kg)
Clock, scores
24" 4x7
(610 mm)
Period
15" 3x5
(381 mm)
25 W 7206 W 120/240 or
120/208 V AC
L1 22 A
L2 28 A
A1 11
24" 4x7
(610 mm)
25 WSO-824 H4’-0", W14’-0", D6"
(1219 mm, 4877 mm,
152 mm)
250 lb
114 kg
(560 lb)
(254 kg)
Half
indicators
40 W
4160 W 120/240 or
120/208 V AC
L1 18 A
L2 17 A
A1 11
Specifications
3-5

Wattage PowerModel Dimensions
(Height, Width,
Depth)
Weight
Uncrated
(Crated)
Digit Size
and Matrix Lamp Maximum (See Note 2)
Amps per Line
(Single Phase)
Driver Number
and Address
18" 3x5
(457 mm)
25 W 2925 W 120/240 or
120/208 V
AC
L1 11 A
L2 17 A
18" 4x7
(457 mm)
25 W
SO-918 H4’-0", W12’-0", D6"
(1219 mm, 3658 mm,
152 mm)
225 lb
102 kg
(455 lb)
(206 kg)
Half
Indicators
40 W
4500 W 120/240 or
120/208 V
AC
L1 17 A
L2 21 A
A1 11
SO-2008
w/TNMC
H5'-6", W16'-0", D6"
(1676 mm, 4877 mm,
152 mm)
300 lb
136 kg
(570 lb)
(259 kg)
All digits
18" 3x5
(457 mm)
25 W 6145 W 120/240 or
120/208 V
AC
L1 22 A
L2 30 A
A1 17
All digits
18" 3x5
(457 mm)
25 W 650 W 120 V AC 6
TI-218 H2’-0", W3’-0", D11"
(610 mm, 914 mm,
279 mm)
20 lb
9 kg
(57 lb)
(26 kg)
All digits
18" 4x7
(457 mm)
25 W 1000 W 120 V AC 9
A1 2
All digits
18" 3x5
(457 mm)
25 W 1300 W 120 V AC 11
TI-418 H2’-0", W6’-0", D11"
(787 mm, 1829 mm,
279 mm)
50 lb
23 kg
(87 lb)
(40 kg)
All digits
18" 4x7
(457 mm)
25 W 2000 W 120 V AC 17
A1 1
TI-2003 H3’-0", W4’-0", D11"
(914 mm, 1219 mm,
279 mm)
110 lb
50 kg
(150 lb)
(68 kg)
All digits
30" 4x7
(762 mm)
40 W 1600 W 120 V AC 14 A1 2
Specifications 3-6

3.2 230 Volt Single-Section Scoreboards
Note 1: Signal wires must be a minimum of 22-gauge with shield. Daktronics recommends using W-1234.
WattageModel Dimensions
(Height, Width,
Depth)
Weight
Uncrated
(Crated)
Digit Size
and Matrix Lamp Maximum
Power Amps per Line
(Single Phase)
Driver Number
and Address
Inning,
scores
18" 3x5
(457 mm)
25 W 1905 W 230 V AC 8 A
Inning,
scores
18" 4x7
(457 mm)
25 W 2780 W 230 V AC 12 A
BA-518 H4’-0", W9’-0", D6"
(1219 mm, 2743 mm,
152 mm)
120 lb
55 kg
(152 lb)
(70 kg)
Ball, Strike
Out indicators
40 W
A1 61
CT-2001 H2’-0", W6’-0", D11"
(610 mm, 1829 mm,
279 mm)
50 lb
23 kg
(83 lb)
(37 kg)
All digits
18" 4x7
(457 mm)
30 W 1800 W 230 V AC 8 A A1 1
24" 4x7
(610 mm)
25 WSO-824 H4’-0", W14’-0", D6"
(1219 mm, 4877 mm,
152 mm)
250 lb
114 kg
(560 lb)
(254 kg)
Half
indicators
40 W
4160 W 230 V AC L1 9 A
L2 9 A
A1 11
Specifications
3-7

Component Locations
4-1
Section 4: Component Locations
Use the following drawings to determine the location of scoreboard components. The drawings are
listed below in alphanumeric order by model number. In the Appendix, they are inserted in
alphanumeric order by drawing number.
Model Drawing Name Drawing No.
BA-515 Component Locations, BA-515 A-126083
BA-518 Component Locations, BA-518 A-126084
BA-618 Component Locations, BA-618 A-126221
BA-624 Component Locations, BA-624 A-126285
BA-718 Component Locations, BA-718 A-126306
BA-1018 Component Locations, BA-1018 A-126353
BA-2003 Component Locations, BA-2003 A-158315
BA-2004 Component Locations, BA-2004 A-152733
CT-2001 Component Locations, CT-2001 A-126429
CT-2002 Component Locations, CT-2002 A-126430
FB-824 Component Locations, FB-824 A-126431
FB-2340 Component Locations, FB-2340 A-137679
MS-915 Component Locations, MS-915 A-126432
MS-918 Component Locations, MS-918 A-124343
MS-2002 Component Locations, MS-2002 A-127235
MS-2002 w/TNMC Component Locations, MS-2002 w/TNMC A-127193
MS-2002 w/TNMC
and 40W Lamps
Component Locations, MS-2002 w/TNMC
and 40W Lamps
A-135738
MS-2004 Component Locations, MS-2004 A-128047
MS-2006 w/TNMC Component Locations, MS-2006 w/TNMC A-132960
MS-2011 w/TNMC Component Locations; MS-2011 A-138889
SO-824 Component Locations, S0-824 A-127285
SO-918 Component Locations, S0-918 A-126433
SO-2008 w/TNMC Component Locations; SO-2008 w/ 832-12 w/TNMC A-150127
TI-218 Component Locations, TI-218 A-126364
TI-418 Component Locations, TI-418 A-126372
TI-2003 Component Locations, TI-2003 A-126434