Dali Phantom Kompas Manual

Item No. 950490-4-0B
PHANTOM EUPHONIA
PHANTOM HELICON
PHANTOM IKON
NPHANTOM KOMPAS
DALI PHANTOM KOMPAS 6M
BACKBOX
INSTALLATION DIRECTIONS
2
ENGLISH
KOMPAS 6M BACKBOX
KOMPAS 6M BACKBOX 2 pcs
4 screws, PH2 2 pcs
Installation directions 1 pc
TABLE 1
FIGURE 1 FIGURE 2
DALI UK [phone] DALI USA [phone] DALI DE [phone] DALI Denmark [phone]
www.dali-speakers.com
Congratulations with your new KOMPAS 6M BACKBOX. We recommend that you go through these installation
directions before mounting the BACKBOX to your KOMPAS loudspeaker.
You can find more information about the products on our website www.dali-speakers.com or by contacting your
local DALI dealer.
MOunting the KOMPAS BACKBOX tO KOMPAS 6M lOudSPeAKer:
1. KOMPAS Loudspeaker Tweeter:
Make sure to protect the tweeter on the KOMPAS
loudspeaker while mounting the BACKBOX by using
the painting cover mask (protection shield that comes
with the KOMPAS 6M loudspeaker). If the cover mask
is no longer available the grille must be in place while
mounting. We strongly recommend that the mounting
is done on a soft surface in order to prevent scratching
the grille.
NOTE: The protection shield/grille must be off while
mounting into the ceiling.
2. BACKBOX-Connectors:
Connection of the KOMPAS speaker to the BACKBOX-
connectors (red/black).
OR

43
KOMPAS 6M BACKBOX
Material 1 mm zinc plated steel
with bitumen damping
Cut-out dimensions (Ø) [mm/inch] 221/8.7
Weight – BACKBOX [kg/lb] 1.6/2.2
Weight – BACKBOX incl. KOMPAS
loudspeaker [kg/lb]
3.6/6.4
TABLE 2 - KOMPAS 6M BACKBOX TECHNICAL SPECIFICATIONS
5
All technical specifications are subject to change without notice.
FIGURE 3 FIGURE 4
FIGURE 5 FIGURE 6
3. Screws:
Make sure to fully tighten all 4 screws when mounting
the BACKBOX to the KOMPAS loudspeaker. Please refer
to the recommendations of use of tools.
4. Connector Block:
We recommend that you dismantle the green Connector
Block from the BACKBOX before connecting to the
amplifier cable.
NOTE: Make sure to fully tighten all screws.
5. Connector Block: 6. Connector Block:
The green Connector Block is equipped with a “Daisy
Chain” (parallel connection) for easy connection of a
2nd KOMPAS. Make sure that you connect the +/- from
the amplifier to the +/- connection of the BACKBOX.
NOTE: If you’re doing a retrofit installation, please be careful not to drop
the KOMPAS loudspeaker when you unscrew the 4 screws. The tweeter is
very fragile so the same precaution is needed when mounting the KOMPAS
loudspeaker into the ceiling.
NOTE: If you haven’t installed your KOMPAS loudspeaker at this stage we
strongly recommend that you read the manual including in the KOMPAS 6M
loudspeaker packaging very carefully.
Recommended tools to use:
• 3 mm HEX bit: For dismantling the KOMPAS loudspeaker from the ceiling
• PH2 bit: For mounting the BACKBOX to the KOMPAS loudspeaker
• Slotted 2,5 mm bit: For connecting the connectors
NOTE: If using an electrical or battery driven screwdriver, we recommend
that you use an extension bit when mounting the BACKBOX to the KOMPAS
loudspeaker because of the narrow space around the doglegs brackets.
AMPLIFIER OUTPUT
FIGURE 7
7. Earthquake Safety Hook:
If using this feature make sure that the wire is attached
to the roof construction. We recommend consulting a
professional builder.
mm - 8.6 inch
280mm-10.8inch
290mm-11.5inch
219.0
256 mm - 10.1 inch

25mm-1.0inch